42f7ec ошибка мерседес актрос

Ниже приведены коды ошибок, выдаваемые электронными системами, грузового автомобиля Мерседес-Бенц Актрос МР4 Евро 6. В справочном видео Вы можете увидеть где их можно найти. Все коды разбиваются (генерируются) блоками управления. К примеру АСМ — Блок управления системы нейтрализации отработанных газов, МСМ — блок управления двигателем, и так далее. Найти свою ошибку ниже из списка можно при помощи нажатия двух клавиш CTRL+F, введя код ошибки в появившейся области для поиска, однако не забывайте сверять блок управления, которому этот код ошибки принадлежит. Удачи!

Да поможет Гугл переводчик Вам!

<!— 00F0EE (0x00F0EE 0x00): MU_PROTO_01 —>

<!— 010209 (0x010209 0x00): Actual Tourque Signal Not Available via CAN —>

<!— 011103 (0x011103 0x00): Diffuser Heater Circuit Failed High —>

<!— 011103 (0x011103 0x00): Diffusor heating for the urea air assited system -short to battery —>

<!— 011103 (0x011103 0x00): Dosing Unit Heater Circuit Failed High —>

<!— 011104 (0x011104 0x00): Diffuser Heater Circuit Failed Low —>

<!— 011104 (0x011104 0x00): Diffusor heating for the urea air assited system -short to ground —>

<!— 011104 (0x011104 0x00): Dosing Unit Heater Circuit Failed Low —>

<!— 011105 (0x011105 0x00): Diffuser Heater Open Circuit —>

<!— 011105 (0x011105 0x00): Diffusor heating for the urea air assited system -Open Loop —>

<!— 011105 (0x011105 0x00): Diffusor heating for the urea air assited system -Open load —>

<!— 011105 (0x011105 0x00): Dosing Unit Heater Open Circuit —>

<!— 01F0EE (0x01F0EE 0x00): MU_PROTO_02 —>

<!— 021103 (0x021103 0x00): Line Heater #1 Circuit Failed High —>

<!— 021103 (0x021103 0x00): SCR Line Heater #1 Circuit Failed High —>

<!— 021103 (0x021103 0x00): Urea Line heating 1 — Short to battery —>

<!— 021104 (0x021104 0x00): Line Heater #1 Circuit Failed Low —>

<!— 021104 (0x021104 0x00): SCR Line Heater #1 Circuit Failed Low —>

<!— 021104 (0x021104 0x00): Urea Line heating 1 — Short to ground —>

<!— 021105 (0x021105 0x00): Line Heater #1 Open Circuit —>

<!— 021105 (0x021105 0x00): SCR Line Heater #1 Open Circuit —>

<!— 021105 (0x021105 0x00): Urea Line heating 1 — Open load —>

<!— 021105 (0x021105 0x00): Urea Line heating 1 — Open loop —>

<!— 02F0EE (0x02F0EE 0x00): MU_PROTO_03 —>

<!— 031103 (0x031103 0x00): Line Heater #2 Circuit Failed High —>

<!— 031103 (0x031103 0x00): SCR Line Heater #2 Circuit Failed High —>

<!— 031103 (0x031103 0x00): Urea Line heating 2 — Short to battery —>

<!— 031104 (0x031104 0x00): Line Heater #2 Circuit Failed Low —>

<!— 031104 (0x031104 0x00): SCR Line Heater #2 Circuit Failed Low —>

<!— 031104 (0x031104 0x00): Urea Line heating 2 — Short to ground —>

<!— 031105 (0x031105 0x00): Line Heater #2 Circuit Failed Open —>

<!— 031105 (0x031105 0x00): SCR Line Heater #2 Circuit Failed Open —>

<!— 031105 (0x031105 0x00): Urea Line heating 2 — Open load —>

<!— 031105 (0x031105 0x00): Urea Line heating 2 — Open loop —>

<!— 03F0EE (0x03F0EE 0x00): MU_PROTO_04 —>

<!— 04100D (0x04100D 0x00): MCM/ACM Software Not Compatable —>

<!— 04100D (0x04100D 0x00): MCM/ACM Software Not Compatible —>

<!— 041103 (0x041103 0x00): Line Heater #3 Circuit Failed High —>

<!— 041103 (0x041103 0x00): SCR Line Heater #3 Circuit Failed High —>

<!— 041103 (0x041103 0x00): Urea Line heating 3 — Short to battery —>

<!— 041104 (0x041104 0x00): Line Heater #3 Circuit Failed Low —>

<!— 041104 (0x041104 0x00): SCR Line Heater #3 Circuit Failed Low —>

<!— 041104 (0x041104 0x00): Urea Line heating 3 — Short to ground —>

<!— 041105 (0x041105 0x00): Line Heater #3 Circuit Failed Open —>

<!— 041105 (0x041105 0x00): SCR Line Heater #3 Circuit Failed Open —>

<!— 041105 (0x041105 0x00): Urea Line heating 3 — Open load —>

<!— 041105 (0x041105 0x00): Urea Line heating 3 — Open loop —>

<!— 04F0EE (0x04F0EE 0x00): MU_PROTO_05 —>

<!— 051103 (0x051103 0x00): Line Heater #4 Circuit Failed High —>

<!— 051103 (0x051103 0x00): SCR Line Heater #4 Circuit Failed High —>

<!— 051103 (0x051103 0x00): Urea Line heating 4 — Short to battery —>

<!— 051104 (0x051104 0x00): Line Heater #4 Circuit Failed Low —>

<!— 051104 (0x051104 0x00): SCR Line Heater #4 Circuit Failed Low —>

<!— 051104 (0x051104 0x00): Urea Line heating 4 — Short to ground —>

<!— 051105 (0x051105 0x00): Line Heater #4 Circuit Failed Open —>

<!— 051105 (0x051105 0x00): SCR Line Heater #4 Circuit Failed Open —>

<!— 051105 (0x051105 0x00): Urea Line heating 4 — Open load —>

<!— 051105 (0x051105 0x00): Urea Line heating 4 — Open loop —>

<!— 05F0EE (0x05F0EE 0x00): MU_PROTO_06 —>

<!— 061103 (0x061103 0x00): DEF General Heater Circuit Failed High —>

<!— 061103 (0x061103 0x00): Line Heater #5 Circuit Failed High —>

<!— 061103 (0x061103 0x00): Urea Line heating 5 — Short to battery —>

<!— 061104 (0x061104 0x00): DEF General Heater Circuit Failed Low —>

<!— 061104 (0x061104 0x00): Line Heater #5 Circuit Failed Low —>

<!— 061104 (0x061104 0x00): Urea Line heating 5 — Short to ground —>

<!— 061105 (0x061105 0x00): DEF General Heater Circuit Failed Open —>

<!— 061105 (0x061105 0x00): Line Heater #5 Circuit Failed Open —>

<!— 061105 (0x061105 0x00): Urea Line heating 5 — Open load —>

<!— 061105 (0x061105 0x00): Urea Line heating 5 — Open loop —>

<!— 06F0EE (0x06F0EE 0x00): MU_PROTO_07 —>

<!— 07F0E1 (0x07F0E1 0x00): MU_RESERVE_04 —>

<!— 07F0EE (0x07F0EE 0x00): MU_PROTO_08 —>

<!— 081102 (0x081102 0x00): Rationality check for t_scr —>

<!— 081103 (0x081103 0x00): SCR Inlet Temperature Sensor Circuit Failed High —>

<!— 081104 (0x081104 0x00): SCR Inlet Temperature Sensor Circuit Failed Low —>

<!— 081108 (0x081108 0x00): MU_OFD_DUMMY_50 —>

<!— 081108 (0x081108 0x00): SCR Inlet Temperature — Signal Spike —>

<!— 08110A (0x08110A 0x00): SCR Inlet Temperature Sensor — Rationality Error —>

<!— 08110E (0x08110E 0x00): MU_SCR_T_CAT_PLAUS —>

<!— 08110E (0x08110E 0x00): rationality check for t_SCR —>

<!— 08110E (0x08110E 0x00): Rationality check for t_scr —>

<!— 08110F (0x08110F 0x00): SCR Inlet Temperature High —>

<!— 081114 (0x081114 0x00): SCR Inlet Temperature Sensor Drift High in Range —>

<!— 081115 (0x081115 0x00): SCR Inlet Temperature Drift in Range —>

<!— 08F0EE (0x08F0EE 0x00): MU_PROTO_09 —>

<!— 08F0F1 (0x08F0F1 0x00): MU_EDU_RESERV_01 —>

<!— 08F0F1 (0x08F0F1 0x00): MU_LO_DIA_NQV_PRE_DEBOUNCE —>

<!— 090402 (0x090402 0x00): ACM2.1 engine hours data erratic, intermittent or incorrect —>

<!— 090402 (0x090402 0x00): MU_ISP_ACM_TIME_RAT_ERROR —>

<!— 09F0EE (0x09F0EE 0x00): MU_PROTO_10 —>

<!— 0AF0EE (0x0AF0EE 0x00): MU_DPF_RESERVE1 —>

<!— 0B1100 (0x0B1100 0x00): Exothermie in the SCR —>

<!— 0B1100 (0x0B1100 0x00): SCR Outlet Temperature High —>

<!— 0B1100 (0x0B1100 0x00): SCR Outlet Temperature Too High —>

<!— 0B1103 (0x0B1103 0x00): SCR Outlet Temperature Sensor Circuit Failed High —>

<!— 0B1104 (0x0B1104 0x00): SCR Outlet Temperature Sensor Circuit Failed Low —>

<!— 0B1107 (0x0B1107 0x00): SCR Outlet Temperature Sensor Out of Range High —>

<!— 0B1108 (0x0B1108 0x00): Gradient of change for t_scr_out —>

<!— 0B1108 (0x0B1108 0x00): MU_OFD_DUMMY_49 —>

<!— 0B1108 (0x0B1108 0x00): SCR Outlet Temperature — Signal Spike —>

<!— 0B110A (0x0B110A 0x00): SCR Outlet Temperature Sensor — Rationality Error —>

<!— 0B1114 (0x0B1114 0x00): SCR Outlet Temperature Sensor Drift High in Range —>

<!— 0B1114 (0x0B1114 0x00): SCR Temperature Drift — Inlet Low/Outlet High —>

<!— 0B1115 (0x0B1115 0x00): SCR Oulet Temperature Drift in Range —>

<!— 0BF0EE (0x0BF0EE 0x00): MU_DPF_RESERVE2 —>

<!— 0C1101 (0x0C1101 0x00): SCR NOX Conversion Efficiency Very Low —>

<!— 0C1101 (0x0C1101 0x00): SCR NOX Coversion Efficiency Very Low —>

<!— 0C1101 (0x0C1101 0x00): SCR NOX Coversion Efficienty Very Low —>

<!— 0C110E (0x0C110E 0x00): MU_OFD_DUMMY_33 —>

<!— 0C110E (0x0C110E 0x00): SCR catalyst nox conversion rate check —>

<!— 0C1112 (0x0C1112 0x00): SCR NOX Conversion Efficiency Low —>

<!— 0C1112 (0x0C1112 0x00): SCR NOX Coversion Efficiency Low —>

<!— 0C1112 (0x0C1112 0x00): SCR NOX Coversion Efficienty Low —>

<!— 0C111F (0x0C111F 0x00): MU_NOX_MON_SCR_EFF_LOW —>

<!— 0CF0EE (0x0CF0EE 0x00): MU_DPF_RESERVE3 —>

<!— 0D0400 (0x0D0400 0x00): DPF HC Absorption Very High —>

<!— 0D040F (0x0D040F 0x00): DPF HC Absorption Warning —>

<!— 0D0410 (0x0D0410 0x00): DPF HC Absorption High —>

<!— 0D0E03 (0x0D0E03 0x00): Actuator and Sensor Supply — Side 1 — Short to battery —>

<!— 0D0E03 (0x0D0E03 0x00): High Side Digital Output 1 Circuit Failed High —>

<!— 0D0E04 (0x0D0E04 0x00): High Side Digital Output 1 Circuit Failed Low —>

<!— 0DF0EE (0x0DF0EE 0x00): MU_DPF_RESERVE4 —>

<!— 0E0E03 (0x0E0E03 0x00): Actuator and Sensor Supply — Side 2 — Short to battery —>

<!— 0E0E03 (0x0E0E03 0x00): High Side Digital Output 2 Circuit Failed High —>

<!— 0E0E04 (0x0E0E04 0x00): High Side Digital Output 2 Circuit Failed Low —>

<!— 0EF0EE (0x0EF0EE 0x00): MU_DPF_RESERVE5 —>

<!— 0F0E03 (0x0F0E03 0x00): Actuator and Sensor Supply — Side 3 — Short to battery —>

<!— 0F0E03 (0x0F0E03 0x00): High Side Digital Output 3 Circuit Failed High —>

<!— 0F0E04 (0x0F0E04 0x00): High Side Digital Output 3 Circuit Failed Low —>

<!— 0FF0EE (0x0FF0EE 0x00): MU_DPF_RESERVE6 —>

<!— 10F0EE (0x10F0EE 0x00): MU_DPF_RESERVE7 —>

<!— 12F0EE (0x12F0EE 0x00): MU_DPF_MON_P_BACK_SRH —>

<!— 13F0EE (0x13F0EE 0x00): MU_DPF_MON_SCR_PIPE_LEAK —>

<!— 14F0EE (0x14F0EE 0x00): MU_DPF_MON_EXG_PIPE_LEAK —>

<!— 151500 (0x151500 0x00): Regeneration Frequency Error — Severe —>

<!— 15150B (0x15150B 0x00): Check if Kalman request a regeneration before the fixed trigger and very late in zone 0 —>

<!— 15150E (0x15150E 0x00): Check if Kalman request a regeneration before the fixed trigger and very early in zone 0 — it is a smoky engine —>

<!— 151510 (0x151510 0x00): Regeneration Frequency Error — Moderate —>

<!— 15151F (0x15151F 0x00): DPF Regen Too Often —>

<!— 15151F (0x15151F 0x00): MU_DPF_ZONE0_DUR_ERR —>

<!— 15F0EE (0x15F0EE 0x00): MU_DPF_MON_DPF_PLUG_HIGH —>

<!— 161100 (0x161100 0x00): check of relation between pump speed and pressure: pump speed too high for given pressure —>

<!— 161100 (0x161100 0x00): Under pressurized DEF system —>

<!— 161101 (0x161101 0x00): check of relation between pump speed and pressure: pump speed too low for given pressure —>

<!— 161101 (0x161101 0x00): Over pressurized DEF system —>

<!— 161102 (0x161102 0x00): MU_EDU_PUMP_SPD_DIFF_SMALL —>

<!— 161102 (0x161102 0x00): pump speed difference between high and low dosing amounts is to small —>

<!— 161102 (0x161102 0x00): Too small difference of DEF pump speed at low respectively at high dosing amounts —>

<!— 161102 (0x161102 0x00): Too small difference of urea pump speed at low respectively at high dosing amounts —>

<!— 161103 (0x161103 0x00): pump speed signal over measurement range —>

<!— 161104 (0x161104 0x00): pump speed signal below measurement range —>

<!— 161113 (0x161113 0x00): DEF pump is not running synchronous —>

<!— 161113 (0x161113 0x00): DEF system is not being controlled as expected —>

<!— 161113 (0x161113 0x00): difference between requested and actual DEF pump speed —>

<!— 161113 (0x161113 0x00): MU_EDU_PUMP_DEF_SPD_INVAL —>

<!— 161113 (0x161113 0x00): MU_EDU_PUMP_UREA_SPD_INVAL —>

<!— 161113 (0x161113 0x00): Urea pump is not running synchronous —>

<!— 16F0E3 (0x16F0E3 0x00): MU_OFD_DUMMY_38 —>

<!— 16F0E4 (0x16F0E4 0x00): MU_OFD_DUMMY_37 —>

<!— 16F0E5 (0x16F0E5 0x00): MU_OFD_DUMMY_39 —>

<!— 16F0EE (0x16F0EE 0x00): MU_DPF_MON_DPF_CRACK —>

<!— 16F0EE (0x16F0EE 0x00): Pressure drop accross the filter too low —>

<!— 171103 (0x171103 0x00): Air Assited pump- Short to battery —>

<!— 171103 (0x171103 0x00): DEF Pump Circuit Failed High —>

<!— 171104 (0x171104 0x00): Air assited pump- Short to ground —>

<!— 171104 (0x171104 0x00): DEF Pump Circuit Failed Low —>

<!— 171105 (0x171105 0x00): Air assisted pump — Open load —>

<!— 171105 (0x171105 0x00): Air assisted pump — Open loop —>

<!— 171105 (0x171105 0x00): DEF Pump Circuit Failed Open —>

<!— 171106 (0x171106 0x00): Current to the urea pump is too high (air assisted system) —>

<!— 171106 (0x171106 0x00): Current to the urea pump is too high — air assisted system —>

<!— 171106 (0x171106 0x00): DEF Pump Supply Current High —>

<!— 171510 (0x171510 0x00): MU_DPF_HC_QUANT_DEF_OP —>

<!— 17151F (0x17151F 0x00): Display HC burn-off request —>

<!— 17151F (0x17151F 0x00): MU_DPF_HC_BRNOFF_REQ —>

<!— 17F0EE (0x17F0EE 0x00): MU_DPF_MON_DPF_PLUG_LOW —>

<!— 17F0EE (0x17F0EE 0x00): Pressure drop accross the filter too high — lowest level —>

<!— 190E03 (0x190E03 0x00): DOC Inlet Pressure Circuit Failed High —>

<!— 190E03 (0x190E03 0x00): DPF Inlet Pressure Circuit Failed High —>

<!— 190E04 (0x190E04 0x00): DOC Inlet Pressure Circuit Failed Low —>

<!— 190E04 (0x190E04 0x00): DPF Inlet Pressure Circuit Failed Low —>

<!— 190E08 (0x190E08 0x00): DOC Inlet Pressure Signal Spike — sporadic defect on p dpf in sensor —>

<!— 190E08 (0x190E08 0x00): DOC Inlet Pressure Signal Spike —>

<!— 190E08 (0x190E08 0x00): DPF In Pressure sensor sporadic defect —>

<!— 190E0A (0x190E0A 0x00): DOC Inlet Pressure Sensor Stuck —>

<!— 190E15 (0x190E15 0x00): DPF Inlet Pressure — Drift Low —>

<!— 191100 (0x191100 0x00): NH3 slip check for Euro VI SCR fault identification —>

<!— 191100 (0x191100 0x00): SCR Outlet NOx High — Non Fueling —>

<!— 1A0E00 (0x1A0E00 0x00): DPF System Back Pressure Too High —>

<!— 1A0E02 (0x1A0E02 0x00): DPF Inlet/Outlet Pressure not Plausible (KEY ON ENGINE OFF) —>

<!— 1A0E02 (0x1A0E02 0x00): DPF Outlet Pressure Sensor — Not Plausible —>

<!— 1A0E02 (0x1A0E02 0x00): p_dpf_out sensor rationality check —>

<!— 1A0E03 (0x1A0E03 0x00): DPF Outlet Pressure Circuit Failed High —>

<!— 1A0E04 (0x1A0E04 0x00): DPF Outlet Pressure Circuit Failed Low —>

<!— 1A0E07 (0x1A0E07 0x00): DPF Outlet Pressure High —>

<!— 1A0E07 (0x1A0E07 0x00): HWL deposit can not be totally removed. —>

<!— 1A0E08 (0x1A0E08 0x00): DPF Out Pressure sensor sporadic defect —>

<!— 1A0E08 (0x1A0E08 0x00): DPF Outlet Pressure Signal Spike — sporadic defect on p dpf out sensor —>

<!— 1A0E08 (0x1A0E08 0x00): DPF Outlet Pressure Signal Spike —>

<!— 1A0E0A (0x1A0E0A 0x00): DPF Outlet Pressure Sensor Stuck —>

<!— 1A0E0E (0x1A0E0E 0x00): MU_DPF_MON_SCR_PIPE_LEAK —>

<!— 1A0E0F (0x1A0E0F 0x00): MU_DPF_MON_P_BACK_SRH —>

<!— 1A0E15 (0x1A0E15 0x00): DPF Oulet Pressure — Drift Low —>

<!— 210D00 (0x210D00 0x00): DEF Dosing Valve Stuck Open —>

<!— 210D00 (0x210D00 0x00): DEF Pressure Duty Cycle High —>

<!— 210D01 (0x210D01 0x00): DEF Dosing Valve Stuck Closed —>

<!— 210D01 (0x210D01 0x00): DEF Pressure Duty Cycle Low —>

<!— 210D03 (0x210D03 0x00): DEF Dosing Valve Circuit Failed High —>

<!— 210D03 (0x210D03 0x00): Urea dosing valve air assisted system- Short to battery —>

<!— 210D04 (0x210D04 0x00): DEF Dosing Valve Circuit Failed Low —>

<!— 210D04 (0x210D04 0x00): Urea dosing valve air assisted system- Short to ground —>

<!— 210D05 (0x210D05 0x00): DEF Dosing Valve Circuit Failed Open —>

<!— 210D05 (0x210D05 0x00): Urea dosing valve air assisted system — Open loop —>

<!— 210D05 (0x210D05 0x00): Urea dosing valve air assisted system — Open load —>

<!— 210D07 (0x210D07 0x00): Clear partial clogging —>

<!— 210D07 (0x210D07 0x00): DEF Unit — Unable to clear Restriction —>

<!— 210D08 (0x210D08 0x00): Air assisted doser unclogging —>

<!— 210D08 (0x210D08 0x00): DEF Metering Unit — Exceeded Unclog Attempts —>

<!— 210D0D (0x210D0D 0x00): DEF Dosing Correction Factor Not Available via CAN —>

<!— 210D1F (0x210D1F 0x00): Dosing Unit Error —>

<!— 210D1F (0x210D1F 0x00): dosing unit is defect (possibly flooded by DEF) —>

<!— 230D00 (0x230D00 0x00): DEF Tank Temperature — High —>

<!— 230D01 (0x230D01 0x00): DEF Tank Temperature — Low —>

<!— 230D03 (0x230D03 0x00): DEF Coolant Valve Circuit Failed High —>

<!— 230D03 (0x230D03 0x00): DEF Tank Heater Circuit Failed High —>

<!— 230D03 (0x230D03 0x00): Urea Tank Heating- Short to battery —>

<!— 230D04 (0x230D04 0x00): DEF Coolant Valve Circuit Failed Low —>

<!— 230D04 (0x230D04 0x00): DEF Tank Heater Circuit Failed Low —>

<!— 230D04 (0x230D04 0x00): Urea Tank Heating- Short to ground —>

<!— 230D05 (0x230D05 0x00): DEF Coolant Valve Circuit Failed Open —>

<!— 230D05 (0x230D05 0x00): DEF Tank Heater Circuit Failed Open —>

<!— 230D05 (0x230D05 0x00): Urea Tank Heating- Open load —>

<!— 230D05 (0x230D05 0x00): Urea Tank Heating- Open loop —>

<!— 230D07 (0x230D07 0x00): DEF Tank Temperature Too Low —>

<!— 230D07 (0x230D07 0x00): Tank Heating Valve Stuck Closed —>

<!— 230D07 (0x230D07 0x00): Urea Tank Heating valve stucked closed —>

<!— 230D1F (0x230D1F 0x00): DEF Tank Temperature Too High —>

<!— 230D1F (0x230D1F 0x00): Tank Heating Valve Stuck Open —>

<!— 230D1F (0x230D1F 0x00): Urea Tank Heating valve stucked open —>

<!— 23F0E5 (0x23F0E5 0x00): MU_OFD_DUMMY_36 —>

<!— 240D00 (0x240D00 0x00): MU_SCR_DIA_MLIT_CASE3 —>

<!— 240D01 (0x240D01 0x00): DEF Quality Warning (Speed Limit Imposed) —>

<!— 240D01 (0x240D01 0x00): Improper DEF Quality Final Warning —>

<!— 240D01 (0x240D01 0x00): urea quality check —>

<!— 240D01 (0x240D01 0x00): urea quality check Final —>

<!— 240D01 (0x240D01 0x00): urea quality check final warning —>

<!— 240D02 (0x240D02 0x00): Improper DEF Quality —>

<!— 240D11 (0x240D11 0x00): DEF Quality Warning —>

<!— 240D11 (0x240D11 0x00): Improper DEF Quality Warning —>

<!— 240D11 (0x240D11 0x00): urea quality check —>

<!— 240D11 (0x240D11 0x00): urea quality check Warning —>

<!— 240D11 (0x240D11 0x00): urea quality check warning —>

<!— 240D12 (0x240D12 0x00): Improper DEF Quality Drate —>

<!— 240D12 (0x240D12 0x00): Improper DEF Quality Warning —>

<!— 240D13 (0x240D13 0x00): MU_ISP_DISC_SENS_ERR —>

<!— 25F0EE (0x25F0EE 0x00): MU_SCR_DUMMY_01 —>

<!— 27F0ED (0x27F0ED 0x00): Fuel Mass Signal Not Available via CAN —>

<!— 28F0E9 (0x28F0E9 0x00): NOx Mass Signal Not Available via CAN —>

<!— 29F0E9 (0x29F0E9 0x00): MU_ISP_HEARTBEAT_CAN2 —>

<!— 29F0ED (0x29F0ED 0x00): MU_ISP_DUMMY_CAN_SNA —>

<!— 2AF0ED (0x2AF0ED 0x00): DEF Dosing Correction Factor Not Available via CAN —>

<!— 2DF0EE (0x2DF0EE 0x00): MU_SCR_DIA_MLIT_CASE1 —>

<!— 2EF0EE (0x2EF0EE 0x00): MU_ISP_KM_PARITY_ERR —>

<!— 2FF0E3 (0x2FF0E3 0x00): MU_ISP_RES_DPF_1_SRH —>

<!— 2FF0E4 (0x2FF0E4 0x00): MU_ISP_RES_DPF_1_SRL —>

<!— 30F0E3 (0x30F0E3 0x00): MU_ISP_RES_DPF_2_SRH —>

<!— 30F0E4 (0x30F0E4 0x00): MU_ISP_RES_DPF_2_SRL —>

<!— 31F0E3 (0x31F0E3 0x00): MU_ISP_RES_SCR_1_SRH —>

<!— 31F0E4 (0x31F0E4 0x00): MU_ISP_RES_SCR_1_SRL —>

<!— 32F0E3 (0x32F0E3 0x00): MU_ISP_RES_SCR_2_SRH —>

<!— 32F0E4 (0x32F0E4 0x00): MU_ISP_RES_SCR_2_SRL —>

<!— 330004 (0x330004 0x00): Intake Air Throttle Circuit Failed Low —>

<!— 330004 (0x330004 0x00): MU_ISP_DUMMY_03_SRL —>

<!— 33F0E3 (0x33F0E3 0x00): MU_ISP_RES_SCR_3_SRH —>

<!— 33F0E4 (0x33F0E4 0x00): MU_ISP_RES_SCR_3_SRL —>

<!— 34F0E3 (0x34F0E3 0x00): MU_ISP_SOOT_SENS_SRH —>

<!— 34F0E4 (0x34F0E4 0x00): MU_ISP_SOOT_SENS_SRL —>

<!— 35F0E3 (0x35F0E3 0x00): MU_ISP_DUMMY_01_SRH —>

<!— 35F0E4 (0x35F0E4 0x00): MU_ISP_DUMMY_01_SRL —>

<!— 36C403 (0x36C403 0x00): MU_UPS_DUMMY_01 —>

<!— 36C404 (0x36C404 0x00): Def Acumulator Failure —>

<!— 36C404 (0x36C404 0x00): Urea pressure out of working range (air assisted system) —>

<!— 36F0E3 (0x36F0E3 0x00): MU_ISP_DUMMY_02_SRH —>

<!— 36F0E4 (0x36F0E4 0x00): MU_ISP_DUMMY_02_SRL —>

<!— 38F0E3 (0x38F0E3 0x00): MU_ISP_RSP_01_DPF_SRH —>

<!— 38F0E4 (0x38F0E4 0x00): MU_ISP_RSP_01_DPF_SRL —>

<!— 39F0E4 (0x39F0E4 0x00): MU_SCR_T_CAT_IN_3_SRH —>

<!— 39F0E4 (0x39F0E4 0x00): SCR Inlet Temperature High —>

<!— 3B1507 (0x3B1507 0x00): DEF pump is blocked —>

<!— 3B1507 (0x3B1507 0x00): EDU DEF pump is blocked —>

<!— 3B1507 (0x3B1507 0x00): EDU urea pump is blocked —>

<!— 3B1507 (0x3B1507 0x00): MU_EDU_PUMP_DEF_BLOCKED —>

<!— 3B1507 (0x3B1507 0x00): MU_EDU_PUMP_UREA_BLOCKED —>

<!— 3B1507 (0x3B1507 0x00): Non DEF flow situation —>

<!— 3BF0EE (0x3BF0EE 0x00): MU_DPF_Q_DOT_DOCB_ERR —>

<!— 3CF0EE (0x3CF0EE 0x00): DEF Tank Zone 4 Condition —>

<!— 3CF0F2 (0x3CF0F2 0x00): MU_SCR_DIA_MLIT_CASE2 —>

<!— 3CF0FF (0x3CF0FF 0x00): DEF Tank Zone 5 Condition —>

<!— 3D1103 (0x3D1103 0x00): MU_ISP_RSP_01_SCR_SRH —>

<!— 3D1104 (0x3D1104 0x00): MU_ISP_RSP_01_SCR_SRL —>

<!— 41F0F2 (0x41F0F2 0x00): HC Slip is too high —>

<!— 41F0F2 (0x41F0F2 0x00): MU_DPF_HC_SLIP_HIGH —>

<!— 42F0EE (0x42F0EE 0x00): MU_OFD_DUMMY_40 —>

<!— 431500 (0x431500 0x00): DPF HC Absorption Very High —>

<!— 43150F (0x43150F 0x00): DPF HC Absorption Warning —>

<!— 431510 (0x431510 0x00): DPF HC Absorption High —>

<!— 44F0EE (0x44F0EE 0x00): ATS Not Started Up —>

<!— 44F0EE (0x44F0EE 0x00): MU_PAR_ATS_START_NOT_EFFECT —>

<!— 45F0EE (0x45F0EE 0x00): ACM Not Parameterized —>

<!— 45F0EE (0x45F0EE 0x00): MU_PAR_ACM_NOT_PARAMETRIZED —>

<!— 4DF0E8 (0x4DF0E8 0x00): Input Signal Spike 1 — Sporadic Defect —>

<!— 4DF0E8 (0x4DF0E8 0x00): Input Signal Spike 1 —>

<!— 4DF0E8 (0x4DF0E8 0x00): Sporadic defect of ADC sensor in ISP40 (MU1) —>

<!— 4EF0E8 (0x4EF0E8 0x00): Input Signal Spike 2 — sporadic defect —>

<!— 4EF0E8 (0x4EF0E8 0x00): Input Signal Spike 2 —>

<!— 4EF0E8 (0x4EF0E8 0x00): Sporadic defect of ADC sensor in ISP40 (MU2) —>

<!— 55F0FF (0x55F0FF 0x00): MU_DPF_MON_TIME_EST_INT —>

<!— 56F0F1 (0x56F0F1 0x00): MU_SCR_DIA_EURO6_Z3 —>

<!— 56F0F2 (0x56F0F2 0x00): MU_SCR_DIA_EURO6_Z4 —>

<!— 57F0E2 (0x57F0E2 0x00): EDU DEF temperature sensor signal drift —>

<!— 57F0E2 (0x57F0E2 0x00): EDU urea temperature sensor signal drift —>

<!— 57F0E2 (0x57F0E2 0x00): MU_EDU_TEMP_DEF_SDRF —>

<!— 57F0E2 (0x57F0E2 0x00): MU_EDU_TEMP_UREA_SDRF —>

<!— 57F0E3 (0x57F0E3 0x00): EDU Temperature Sensor Signal Failed High —>

<!— 57F0E3 (0x57F0E3 0x00): MU_EDU_T_DEF_SRH / Dave’s Text needed —>

<!— 57F0E4 (0x57F0E4 0x00): EDU Temperature Sensor Signal Failed Low —>

<!— 57F0E4 (0x57F0E4 0x00): MU_EDU_T_DEF_SRL / Dave’s Text needed —>

<!— 58F0E3 (0x58F0E3 0x00): EDU Pressure Sensor Signal Failed High —>

<!— 58F0E3 (0x58F0E3 0x00): MU_EDU_P_DEF_SRH / Dave’s Text needed —>

<!— 58F0E4 (0x58F0E4 0x00): EDU Pressure Sensor Signal Failed Low —>

<!— 58F0E4 (0x58F0E4 0x00): MU_EDU_P_DEF_SRL / Dave’s Text needed —>

<!— 59F0E3 (0x59F0E3 0x00): EDU sensor supply signal range high. —>

<!— 59F0E3 (0x59F0E3 0x00): MU_EDU_SENS_SUPPLY_SRH / Dave’s Text needed —>

<!— 59F0E3 (0x59F0E3 0x00): MU_EDU_SENS_SUPPLY_SRH —>

<!— 59F0E4 (0x59F0E4 0x00): EDU sensor supply signal range low. —>

<!— 59F0E4 (0x59F0E4 0x00): MU_EDU_SENS_SUPPLY_SRL / Dave’s Text needed —>

<!— 59F0E4 (0x59F0E4 0x00): MU_EDU_SENS_SUPPLY_SRL —>

<!— 5AF0E3 (0x5AF0E3 0x00): EDU urea injector valve shortcut to battery. Urea injector team plans to block the urea injection. —>

<!— 5AF0E3 (0x5AF0E3 0x00): EDU Dosing Valve Signal Failed High —>

<!— 5AF0E3 (0x5AF0E3 0x00): EDU urea injector valve shortcut to battery. Urea injector team plans to block the urea injection. —>

<!— 5AF0E3 (0x5AF0E3 0x00): MU_EDU_DOS_VALVE_SC_UBAT / Dave’s Text needed —>

<!— 5AF0E4 (0x5AF0E4 0x00): EDU Dosing Valve Signal Failed Low —>

<!— 5AF0E4 (0x5AF0E4 0x00): EDU urea injector valve shortcut to ground. —>

<!— 5AF0E4 (0x5AF0E4 0x00): MU_EDU_DOS_VALVE_SC_GND / Dave’s Text needed —>

<!— 5AF0E5 (0x5AF0E5 0x00): EDU dosing valve open load —>

<!— 5AF0E5 (0x5AF0E5 0x00): EDU Dosing Valve Signal Failed Open —>

<!— 5AF0E5 (0x5AF0E5 0x00): MU_EDU_DOS_VALVE_OL / Dave’s Text needed —>

<!— 5BF0E3 (0x5BF0E3 0x00): EDU DEF heater shortcut to battery —>

<!— 5BF0E3 (0x5BF0E3 0x00): EDU urea heater shortcut to battery —>

<!— 5BF0E3 (0x5BF0E3 0x00): MU_EDU_HEATER_SC_UBAT / Dave’s Text needed —>

<!— 5BF0E3 (0x5BF0E3 0x00): MU_EDU_HEATER_SC_UBAT —>

<!— 5BF0E4 (0x5BF0E4 0x00): EDU DEF heater shortcut to ground —>

<!— 5BF0E4 (0x5BF0E4 0x00): EDU urea heater shortcut to ground —>

<!— 5BF0E4 (0x5BF0E4 0x00): MU_EDU_HEATER_SC_GND / Dave’s Text needed —>

<!— 5BF0E4 (0x5BF0E4 0x00): MU_EDU_HEATER_SC_GND —>

<!— 5BF0E5 (0x5BF0E5 0x00): EDU urea heater open load —>

<!— 5BF0E5 (0x5BF0E5 0x00): Heater of EDU open load —>

<!— 5BF0E5 (0x5BF0E5 0x00): MU_EDU_HEATER_SC_OL / Dave’s Text needed —>

<!— 5BF0E5 (0x5BF0E5 0x00): MU_EDU_HEATER_SC_OL —>

<!— 5CF0E3 (0x5CF0E3 0x00): EDU high side switch 1 -pump and heater- shortcut to battery —>

<!— 5CF0E3 (0x5CF0E3 0x00): EDU high side switch 1 (pump + heater) shortcut to battery —>

<!— 5CF0E3 (0x5CF0E3 0x00): EDU high side switch 1 -pump and heater- shortcut to battery —>

<!— 5CF0E3 (0x5CF0E3 0x00): MU_EDU_HS1_SC_UBAT / Dave’s Text needed —>

<!— 5CF0E3 (0x5CF0E3 0x00): MU_EDU_HS1_SC_UBAT —>

<!— 5CF0E4 (0x5CF0E4 0x00): EDU high side switch 1 -pump and heater shortcut to ground —>

<!— 5CF0E4 (0x5CF0E4 0x00): EDU high side switch 1 (pump + heater) shortcut to ground —>

<!— 5CF0E4 (0x5CF0E4 0x00): EDU high side switch 1 -pump and heater shortcut to ground —>

<!— 5CF0E4 (0x5CF0E4 0x00): MU_EDU_HS1_SC_GND / Dave’s Text needed —>

<!— 5CF0E4 (0x5CF0E4 0x00): MU_EDU_HS1_SC_GND —>

<!— 5DF0E3 (0x5DF0E3 0x00): EDU high side switch 2 (pump + heater) shortcut to battery —>

<!— 5DF0E3 (0x5DF0E3 0x00): EDU high side switch 2 -pump and heater- shortcut to battery —>

<!— 5DF0E3 (0x5DF0E3 0x00): MU_EDU_HS2_SC_UBAT / Dave’s Text needed —>

<!— 5DF0E3 (0x5DF0E3 0x00): MU_EDU_HS2_SC_UBAT —>

<!— 5DF0E4 (0x5DF0E4 0x00): EDU high side switch 2 (pump + heater) shortcut to ground —>

<!— 5DF0E4 (0x5DF0E4 0x00): EDU high side switch 2 -pump and heater- shortcut to ground —>

<!— 5DF0E4 (0x5DF0E4 0x00): MU_EDU_HS2_SC_GND / Dave’s Text needed —>

<!— 5DF0E4 (0x5DF0E4 0x00): MU_EDU_HS2_SC_GND —>

<!— 5EF0E3 (0x5EF0E3 0x00): EDU battery signal range high —>

<!— 5EF0E3 (0x5EF0E3 0x00): MU_EDU_UBAT_SRH / Dave’s Text needed —>

<!— 5EF0E3 (0x5EF0E3 0x00): MU_EDU_UBAT_SRH —>

<!— 5EF0E4 (0x5EF0E4 0x00): EDU battery signal range low —>

<!— 5EF0E4 (0x5EF0E4 0x00): MU_EDU_UBAT_SRL / Dave’s Text needed —>

<!— 5EF0E4 (0x5EF0E4 0x00): MU_EDU_UBAT_SRL —>

<!— 5F0402 (0x5F0402 0x00): Air fuel ratio rationality check —>

<!— 5F0402 (0x5F0402 0x00): Nox Signal Not Plausible —>

<!— 5F041F (0x5F041F 0x00): Air fuel ratio rationality check —>

<!— 5F041F (0x5F041F 0x00): Nox Signal Not Plausible —>

<!— 5FF0E9 (0x5FF0E9 0x00): ACM DM1 Message Not Received at Dash Cluster —>

<!— 5FF0E9 (0x5FF0E9 0x00): Dashboard doesn’t recieve ACM DM1 / Dave’s text needed —>

<!— 600F07 (0x600F07 0x00): Incomplete Regeneration —>

<!— 600F07 (0x600F07 0x00): zone 5 regeneration is interrupted — incomplete regeneration —>

<!— 600F11 (0x600F11 0x00): MU_DPF_EFF_CHECK —>

<!— 600F12 (0x600F12 0x00): DPF Efficency Error —>

<!— 600F12 (0x600F12 0x00): DPF Pressure — Out of Range Low — Broken DPF —>

<!— 600F12 (0x600F12 0x00): DPF Pressure — Out of Range Low —>

<!— 60F0FF (0x60F0FF 0x00): MU_OFD_DUMMY_25 —>

<!— 60F0FF (0x60F0FF 0x00): Obsolete MU3 —>

<!— 61F0E3 (0x61F0E3 0x00): EDU DEF pump schortcut to battery —>

<!— 61F0E3 (0x61F0E3 0x00): EDU urea pump schortcut to battery —>

<!— 61F0E3 (0x61F0E3 0x00): MU_EDU_PUMP_DEF_SC_UBAT —>

<!— 61F0E3 (0x61F0E3 0x00): MU_EDU_PUMP_UREA_SC_UBAT —>

<!— 61F0E4 (0x61F0E4 0x00): EDU DEF pump schortcut to ground —>

<!— 61F0E4 (0x61F0E4 0x00): EDU urea pump schortcut to ground —>

<!— 61F0E4 (0x61F0E4 0x00): MU_EDU_PUMP_DEF_SC_GND —>

<!— 61F0E4 (0x61F0E4 0x00): MU_EDU_PUMP_UREA_SC_GND —>

<!— 61F0E5 (0x61F0E5 0x00): EDU DEF pump open load —>

<!— 61F0E5 (0x61F0E5 0x00): EDU urea pump open load —>

<!— 61F0E5 (0x61F0E5 0x00): MU_EDU_PUMP_DEF_OL —>

<!— 61F0E5 (0x61F0E5 0x00): MU_EDU_PUMP_UREA_OL —>

<!— 620103 (0x620103 0x00): Relative Humidity Sensor Circuit Failed High —>

<!— 620104 (0x620104 0x00): Relative Humidity Sensor Circuit Failed Low —>

<!— 62F0F1 (0x62F0F1 0x00): EDU DEF filter service requirement —>

<!— 62F0F1 (0x62F0F1 0x00): EDU urea filter service requirement —>

<!— 62F0F1 (0x62F0F1 0x00): MU_EDU_FILT_DEF_SERV —>

<!— 62F0F1 (0x62F0F1 0x00): MU_EDU_FILT_UREA_SERV —>

<!— 62F0F2 (0x62F0F2 0x00): EDU DEF filter life time expired — service routine —>

<!— 62F0F2 (0x62F0F2 0x00): EDU urea filter life time expired — service routine —>

<!— 62F0F2 (0x62F0F2 0x00): EDU urea filter life time expired (service routine) —>

<!— 62F0F2 (0x62F0F2 0x00): MU_EDU_FILT_DEF_LT_EX —>

<!— 62F0F2 (0x62F0F2 0x00): MU_EDU_FILT_UREA_LT_EX —>

<!— 63F0E0 (0x63F0E0 0x00): EDU DEF pump speed too high —>

<!— 63F0E0 (0x63F0E0 0x00): EDU urea pump speed too high —>

<!— 63F0E0 (0x63F0E0 0x00): MU_EDU_PUMP_SPD_HI —>

<!— 63F0E1 (0x63F0E1 0x00): EDU DEF pump speed too low —>

<!— 63F0E1 (0x63F0E1 0x00): EDU urea pump speed too low —>

<!— 63F0E1 (0x63F0E1 0x00): MU_EDU_PUMP_SPD_LO —>

<!— 63F0E2 (0x63F0E2 0x00): Too small difference of DEF pump speed at low respectively at high dosing amounts —>

<!— 63F0E2 (0x63F0E2 0x00): Too small difference of urea pump speed at low respectively at high dosing amounts —>

<!— 63F0E7 (0x63F0E7 0x00): EDU DEF pump is blocked —>

<!— 63F0E7 (0x63F0E7 0x00): EDU urea pump is blocked —>

<!— 63F0F3 (0x63F0F3 0x00): DEF pump is not running synchronous —>

<!— 63F0F3 (0x63F0F3 0x00): Urea pump is not running synchronous —>

<!— 64F0EE (0x64F0EE 0x00): Check if Kalman request a regeneration before the fixed trigger and very early in zone 0 it is a smoky engine —>

<!— 64F0EE (0x64F0EE 0x00): Check if Kalman request a regeneration before the fixed trigger and very early in zone 0 — it is a smoky engine —>

<!— 64F0EE (0x64F0EE 0x00): MU_DPF_SOOT_DP_DEV_HI —>

<!— 64F0FF (0x64F0FF 0x00): Check if Kalman request a regeneration before the fixed trigger and very late in zone 0 —>

<!— 64F0FF (0x64F0FF 0x00): MU_DPF_SOOT_DP_DEV_LO —>

<!— 65F0EC (0x65F0EC 0x00): EDU ECU internal fault —>

<!— 65F0EC (0x65F0EC 0x00): MU_EDU_ECU_TRAP —>

<!— 65F0ED (0x65F0ED 0x00): EDU memory check failed —>

<!— 65F0ED (0x65F0ED 0x00): MU_EDU_ECU_MEM_CHK_ERR —>

<!— 66F0E7 (0x66F0E7 0x00): MU_EDU_PRESS_REL_VLV_DEF —>

<!— 66F0E7 (0x66F0E7 0x00): Pressure relief valve is stuck closed —>

<!— 67F0FF (0x67F0FF 0x00): EDU pump speed signal range low. —>

<!— 67F0FF (0x67F0FF 0x00): MU_EDU_PUMP_DEF_SPD_INTRP —>

<!— 67F0FF (0x67F0FF 0x00): MU_EDU_PUMP_UREA_SPD_INTRP —>

<!— 68F0ED (0x68F0ED 0x00): EDU dataset is not valid —>

<!— 68F0ED (0x68F0ED 0x00): MU_EDU_DATASET_NOT_VALID —>

<!— 69F0E9 (0x69F0E9 0x00): MU_ISP_HEARTBEAT_CAN1 —>

<!— 6AF0E9 (0x6AF0E9 0x00): MU_ISP_HEARTBEAT_CAN3 —>

<!— 6BF0E9 (0x6BF0E9 0x00): MU_ISP_HEARTBEAT_CAN4 —>

<!— 6C000D (0x6C000D 0x00): Ambient Air Pressure Signal Not Available via CAN —>

<!— 6CF0EE (0x6CF0EE 0x00): MU_ATS_DIA_TDOC_IN_FIN_RAT —>

<!— 6CF0EE (0x6CF0EE 0x00): MU_NOX_DUMMY_01 —>

<!— 6CF0EE (0x6CF0EE 0x00): MU_NOX_EMISSION_DOS_SL_SCR_KAT —>

<!— 6D1603 (0x6D1603 0x00): MU_DPS_UBAT —>

<!— 6D1604 (0x6D1604 0x00): MU_DPS_SHORT_CIRC —>

<!— 6D1609 (0x6D1609 0x00): MU_DPS_DIA_CAN_SNA —>

<!— 6D160C (0x6D160C 0x00): MU_DPS_SELF_DIAG —>

<!— 6D160D (0x6D160D 0x00): MU_DPS_DIA_SENS_SNA —>

<!— 6D160F (0x6D160F 0x00): MU_DPS_IDE_NEG —>

<!— 6D1610 (0x6D1610 0x00): MU_DPS_IDE_NEG_ON —>

<!— 6D1611 (0x6D1611 0x00): MU_DPS_IDE_POS —>

<!— 6D1612 (0x6D1612 0x00): MU_DPS_IDE_NEG_OFF —>

<!— 6D1613 (0x6D1613 0x00): MU_DPS_SNA —>

<!— 6DF0EE (0x6DF0EE 0x00): MU_NOX_DUMMY_02 —>

<!— 6DF0EE (0x6DF0EE 0x00): MU_NOX_EMISSION_DOS_SRL —>

<!— 6E0009 (0x6E0009 0x00): Coolant Temperature Signal Not Available via CAN —>

<!— 6EF0EE (0x6EF0EE 0x00): MU_NOX_DUMMY_03 —>

<!— 6EF0EE (0x6EF0EE 0x00): MU_NOX_EMISSION_ROH_SH —>

<!— 6FF0EE (0x6FF0EE 0x00): MU_NOX_DUMMY_04 —>

<!— 6FF0EE (0x6FF0EE 0x00): MU_NOX_EMISSION_SCR_KAT_DEF —>

<!— 701503 (0x701503 0x00): DEF General Heater Circuit Failed High —>

<!— 701503 (0x701503 0x00): SCR Line Heater #5 Circuit Failed High —>

<!— 701503 (0x701503 0x00): Urea Line heating 5 — Short to battery —>

<!— 701504 (0x701504 0x00): DEF General Heater Circuit Failed Low —>

<!— 701504 (0x701504 0x00): SCR Line Heater #5 Circuit Failed Low —>

<!— 701504 (0x701504 0x00): Urea Line heating 5 — Short to ground —>

<!— 701505 (0x701505 0x00): DEF General Heater Circuit Failed Open —>

<!— 701505 (0x701505 0x00): SCR Line Heater #5 Circuit Failed Open —>

<!— 701505 (0x701505 0x00): Urea Line heating 5 — Open load —>

<!— 70F0EE (0x70F0EE 0x00): MU_NOX_DUMMY_05 —>

<!— 70F0EE (0x70F0EE 0x00): MU_NOX_EMISSION_SENSOR_DEF —>

<!— 710202 (0x710202 0x00): CPC Message not Received or Stopped Arriving —>

<!— 710202 (0x710202 0x00): MU_CAN_CPC_NO_COM —>

<!— 710209 (0x710209 0x00): MU_ISP_HEARTBEAT_CAN1 —>

<!— 710209 (0x710209 0x00): PT-CAN Heartbeat Missing —>

<!— 71F0EE (0x71F0EE 0x00): Euro 5 SCR fault identification Level 1 SR —>

<!— 71F0EE (0x71F0EE 0x00): MU_NOX_DUMMY_06 —>

<!— 71F0EE (0x71F0EE 0x00): MU_NOX_LEVEL1_SR —>

<!— 72F0EE (0x72F0EE 0x00): Euro 5 SCR fault identification Level 2 HWL Quali SR —>

<!— 72F0EE (0x72F0EE 0x00): MU_NOX_DUMMY_07 —>

<!— 72F0EE (0x72F0EE 0x00): MU_NOX_LEVEL2_HWL_QUALI_SR —>

<!— 73160C (0x73160C 0x00): MU_DPS_HTR_DIAG —>

<!— 73160F (0x73160F 0x00): MU_DPS_HTR_ON —>

<!— 731611 (0x731611 0x00): MU_DPS_HTR_OFF —>

<!— 73F0EE (0x73F0EE 0x00): Euro 5 SCR fault identification Level 2 MIN DOS SR —>

<!— 73F0EE (0x73F0EE 0x00): MU_NOX_DUMMY_08 —>

<!— 73F0EE (0x73F0EE 0x00): MU_NOX_LEVEL2_MIN_DOS_SR —>

<!— 74020E (0x74020E 0x00): ECU Software Error —>

<!— 74020E (0x74020E 0x00): MU reserve —>

<!— 740703 (0x740703 0x00): Air lock valve for the urea air assited system -short to battery —>

<!— 740703 (0x740703 0x00): DEF Air Lock Valve Circuit Failed High —>

<!— 740704 (0x740704 0x00): Air lock valve for the urea air assited system -short to ground —>

<!— 740704 (0x740704 0x00): DEF Air Lock Valve Circuit Failed Low —>

<!— 740705 (0x740705 0x00): Air lock valve for the urea air assited system -Open Loop —>

<!— 740705 (0x740705 0x00): Air lock valve for the urea air assited system -Open Load —>

<!— 740705 (0x740705 0x00): DEF Air Lock Valve Circuit Failed Open —>

<!— 74F0EE (0x74F0EE 0x00): Euro 5 SCR fault identification — Level 2 SR —>

<!— 74F0EE (0x74F0EE 0x00): MU_NOX_DUMMY_09 —>

<!— 74F0EE (0x74F0EE 0x00): MU_NOX_LEVEL2_SR —>

<!— 75020C (0x75020C 0x00): ACM Internal Error —>

<!— 75F0FF (0x75F0FF 0x00): DOC/DPF (for 2-leg sysetm) presence detection —>

<!— 75F0FF (0x75F0FF 0x00): DOC/DPF for 2-leg sysetm presence detection —>

<!— 75F0FF (0x75F0FF 0x00): MU_ATS_DIA_DOCBDPFB_PRES —>

<!— 760202 (0x760202 0x00): Powerlatch of last driving cycle not completed —>

<!— 76020A (0x76020A 0x00): Loss of non-volatile data —>

<!— 76020C (0x76020C 0x00): E2P Hardware Error —>

<!— 76020C (0x76020C 0x00): Fault to write to the e2p —>

<!— 76020C (0x76020C 0x00): MU_E2P_RW_ERR —>

<!— 76020D (0x76020D 0x00): MU_AUTH_E2P_DATA_LOSS inform TP PEE Team Kowol —>

<!— 76020E (0x76020E 0x00): E2P Emulation Hardware Error —>

<!— 76020E (0x76020E 0x00): E2P Emulation ReadWrite Error —>

<!— 76021F (0x76021F 0x00): Incorrect UDS security calibration —>

<!— 76021F (0x76021F 0x00): MU_DSERV_CHK_SEC_TBL —>

<!— 76F0EE (0x76F0EE 0x00): SCR Inlet Temperature Sensor — Rationality Error —>

<!— 76F0FF (0x76F0FF 0x00): SCR Outlet Temperature Sensor — Rationality Error —>

<!— 770E1F (0x770E1F 0x00): Regen Inhibit Swicht active when zone logic increments —>

<!— 77F0E0 (0x77F0E0 0x00): Regeneration Frequency Error — Severe —>

<!— 77F0E9 (0x77F0E9 0x00): EDU CAN Message Not Received —>

<!— 77F0F0 (0x77F0F0 0x00): Regeneration Frequency Error — Moderate —>

<!— 78F0FF (0x78F0FF 0x00): DEF Tank Level — Zone 2 —>

<!— 78F0FF (0x78F0FF 0x00): Urea tank level check — Lim2 — Refill —>

<!— 79F0FF (0x79F0FF 0x00): DEF Tank Level — Zone 3 —>

<!— 79F0FF (0x79F0FF 0x00): Urea tank level check — Lim3 -Torque limiter —>

<!— 7AF0FF (0x7AF0FF 0x00): DEF Tank Level — Zone 4 —>

<!— 7AF0FF (0x7AF0FF 0x00): Urea tank level check — Lim4 -Speed limiter —>

<!— 7BF0FF (0x7BF0FF 0x00): EDU dosing unit defect —>

<!— 7CF0FF (0x7CF0FF 0x00): EDU supply unit Defect —>

<!— 7DF0E2 (0x7DF0E2 0x00): FSG: MU_SCR_DIA_T_UREA_TANK_RAT —>

<!— 7DF0E2 (0x7DF0E2 0x00): Reductant Tank Temperature Sensor Circuit Range/Performance —>

<!— 7E1400 (0x7E1400 0x00): Regulatory Fault Ignored — Final Action (Speed Limit) —>

<!— 7E140F (0x7E140F 0x00): Regulatory Fault Ignored — Derate On —>

<!— 7E1410 (0x7E1410 0x00): Regulatory Fault Ignored — Final Action Pending —>

<!— 7EF0FF (0x7EF0FF 0x00): DOC Clean-up Fault —>

<!— 7EF0FF (0x7EF0FF 0x00): DOC plugging clearance process is not terminated successfully. —>

<!— 7F0E1F (0x7F0E1F 0x00): MU_DPF_LIGHT_OFF_ERR —>

<!— 7F0E1F (0x7F0E1F 0x00): Parked Regen Failed — DOC Temp In Low Preventing Dosing —>

<!— 7F150D (0x7F150D 0x00): Fuel Mass Signal Not Available via CAN —>

<!— 7FF0FF (0x7FF0FF 0x00): SCR Catalyst — Age :Limit — SCR catalyst is defect —>

<!— 7FF0FF (0x7FF0FF 0x00): SCR Catalyst — Age :Limit —>

<!— 80F0F1 (0x80F0F1 0x00): MU_SCR_ADS_FILT_DEF_SERV —>

<!— 80F0F1 (0x80F0F1 0x00): MU_SCR_ADS_FILT_UREA_SERV —>

<!— 80F0F2 (0x80F0F2 0x00): MU_SCR_ADS_FILT_DEF_LT_EX —>

<!— 80F0F2 (0x80F0F2 0x00): MU_SCR_ADS_FILT_UREA_LT_EX —>

<!— 810E1F (0x810E1F 0x00): MU_DPF_TARGET_TEMP_ERR —>

<!— 810E1F (0x810E1F 0x00): Parked Regen Failed — DOC Temp Out, Not Reaching Target Temp —>

<!— 81F0EA (0x81F0EA 0x00): MU_ISP_ACM_TIME_RAT_ERROR —>

<!— 82F0E9 (0x82F0E9 0x00): MU_CAN_CPC_NO_COM —>

<!— 83F0E3 (0x83F0E3 0x00): High Side Digital Output Supply Voltage Circuit Failed High —>

<!— 83F0E3 (0x83F0E3 0x00): High Side Digital Output UV_DOS Circuit Failed High —>

<!— 83F0E4 (0x83F0E4 0x00): High Side Digital Output UV_DOS Circuit Failed Low —>

<!— 84F0E7 (0x84F0E7 0x00): DEF pump is blocked —>

<!— 85F0F1 (0x85F0F1 0x00): DEF filter change interval —>

<!— 85F0F2 (0x85F0F2 0x00): DEF filter overloaded —>

<!— 86F0E3 (0x86F0E3 0x00): check of relation between pump speed and pressure: DEF pump speed too high for given pressure —>

<!— 86F0E4 (0x86F0E4 0x00): check of relation between pump speed and pressure: DEF pump speed too low for given pressure —>

<!— 86F0E4 (0x86F0E4 0x00): MU_EDU_RESERV_03 —>

<!— 870E00 (0x870E00 0x00): Soot Level Very High — Zone 5 Operation —>

<!— 870E00 (0x870E00 0x00): Soot Level Very High —>

<!— 870E0F (0x870E0F 0x00): DPF Zone 3 Condition —>

<!— 870E10 (0x870E10 0x00): Soot Level High — Zone 4 Operation —>

<!— 870E10 (0x870E10 0x00): Soot Level High —>

<!— 870E1F (0x870E1F 0x00): DPF Zone 2 Condition —>

<!— 87F0E3 (0x87F0E3 0x00): check of relation between pump speed and pressure: DEF pump speed too high for given pressure —>

<!— 87F0E3 (0x87F0E3 0x00): MU_EDU_RESERV_04 —>

<!— 87F0E4 (0x87F0E4 0x00): check of relation between pump speed and pressure: pump speed too low for given pressure —>

<!— 87F0E4 (0x87F0E4 0x00): MU_EDU_RESERV_02 —>

<!— 880E0F (0x880E0F 0x00): DPF Ash Clean Request —>

<!— 880E10 (0x880E10 0x00): DPF Ash Derate Request —>

<!— 88F0E7 (0x88F0E7 0x00): DEF pressure relieve valve stuck open or closed —>

<!— 88F0E7 (0x88F0E7 0x00): DEF system has been over pressurized —>

<!— 89F0FF (0x89F0FF 0x00): Non DEF flow situation —>

<!— 89F0FF (0x89F0FF 0x00): supply unit is defect (possibly flooded by DEF) —>

<!— 8AF0E3 (0x8AF0E3 0x00): MU_ISP_T_DEF_MIXER_SRH —>

<!— 8AF0E4 (0x8AF0E4 0x00): MU_ISP_T_DEF_MIXER_SRL —>

<!— 8BF0F1 (0x8BF0F1 0x00): MU_ATS_DIA_COLD_THAW —>

<!— 8CF0F1 (0x8CF0F1 0x00): MU_ATS_DIA_EXH_T_LIGHTOFF —>

<!— 8CF0F1 (0x8CF0F1 0x00): Selective Catalyst Reduction (SCR) Inlet Temperature Too Low —>

<!— 8DF0E1 (0x8DF0E1 0x00): MU_SOOT_SEN_NOT_IN_EXHT —>

<!— 8DF0EE (0x8DF0EE 0x00): MU_SOOT_SENSOR_EFF —>

<!— 8DF0F4 (0x8DF0F4 0x00): MU_SOOT_SENSOR_DRIFT_HIGH —>

<!— 8DF0F5 (0x8DF0F5 0x00): MU_SOOT_SENSOR_DRIFT_LOW —>

<!— 8EF0EE (0x8EF0EE 0x00): MU_SCR_DIA_RSTRT_REST_REL —>

<!— 8FF0F0 (0x8FF0F0 0x00): MU_SOOT_SENS_HTR_PERF_ERR —>

<!— 900C02 (0x900C02 0x00): SCR Outlet NOx Sensor — Rationality Error —>

<!— 900C03 (0x900C03 0x00): SCR Inlet Nox Sensor Circuit Failed High —>

<!— 900C04 (0x900C04 0x00): SCR Inlet Nox Sensor Circuit Failed Low —>

<!— 900C07 (0x900C07 0x00): MU_NOX_RAW_RD_SENS_STAT —>

<!— 900C07 (0x900C07 0x00): Nox raw sensor presence check —>

<!— 900C0B (0x900C0B 0x00): Nox raw sensor rationality check for Euro VI SCR fault identification —>

<!— 900C0B (0x900C0B 0x00): SCR Inlet NOx — Rationality Error —>

<!— 900C0D (0x900C0D 0x00): SCR Inlet Nox Sensor Signal Not Available —>

<!— 900C0F (0x900C0F 0x00): MU_NOX_MON_NOX_RAW_SRH —>

<!— 900C12 (0x900C12 0x00): MU_RESERVE_02 —>

<!— 90F0EC (0x90F0EC 0x00): MU_SOOT_SENSOR_IDE_FAIL —>

<!— 91F0EE (0x91F0EE 0x00): MU_SOOT_SENSOR_T_PRB_ERR —>

<!— 92F0EE (0x92F0EE 0x00): MU_SOOT_SENSOR_HTR_FAIL —>

<!— 93F0EE (0x93F0EE 0x00): MU_SOOT_SENSOR_PWR_ERR —>

<!— 940403 (0x940403 0x00): Turbo Compressor Inlet Temperature Circuit Failed High —>

<!— 940404 (0x940404 0x00): Turbo Compressor Inlet Temperature Circuit Failed Low —>

<!— 94F0E4 (0x94F0E4 0x00): MU_ISP_DUMMY_03_SRL —>

<!— 95F0E3 (0x95F0E3 0x00): MU_ISP_DUMMY_04_SRH —>

<!— 95F0E4 (0x95F0E4 0x00): MU_ISP_DUMMY_04_SRL —>

<!— 96100E (0x96100E 0x00): Tier4 Inducement System has not been activated —>

<!— 96F0EE (0x96F0EE 0x00): MU reserve —>

<!— 970C07 (0x970C07 0x00): MU_NOX_RAW_RC —>

<!— 970C07 (0x970C07 0x00): NOx RAW Sensor not ready after dewpoint enable check —>

<!— 970C07 (0x970C07 0x00): NOx RAW Sensor ready after dewpoint enable check —>

<!— 981303 (0x981303 0x00): Actuator and Sensor Supply — Side 4 — Short to battery —>

<!— 981303 (0x981303 0x00): Coolant Valve Supply Voltage Failed High —>

<!— 981303 (0x981303 0x00): High Side Digital Output 4 Circuit Failed High —>

<!— 981304 (0x981304 0x00): Coolant Valve Supply Voltage Failed Low —>

<!— 981304 (0x981304 0x00): High Side Digital Output 4 Circuit Failed Low —>

<!— 98F0F2 (0x98F0F2 0x00): MU_RESERVE_02 —>

<!— 991303 (0x991303 0x00): Actuator and Sensor Supply — Side 5 — Short to battery —>

<!— 991303 (0x991303 0x00): High Side Digital Output 5 Circuit Failed High —>

<!— 991304 (0x991304 0x00): High Side Digital Output 5 Circuit Failed Low —>

<!— 99F0E0 (0x99F0E0 0x00): MU_SCR_DIA_MLIT_CASE3 —>

<!— 9A0C02 (0x9A0C02 0x00): SCR Outlet Nox Sensor — Drift —>

<!— 9A0C02 (0x9A0C02 0x00): SCR Outlet Nox Sensor Drift in Range —>

<!— 9A0C03 (0x9A0C03 0x00): SCR Outlet Nox Sensor Circuit Failed High —>

<!— 9A0C04 (0x9A0C04 0x00): SCR Outlet Nox Sensor Circuit Failed Low —>

<!— 9A0C07 (0x9A0C07 0x00): MU_NOX_OUT_RD_SENS_STAT —>

<!— 9A0C07 (0x9A0C07 0x00): Nox out sensor presence check —>

<!— 9A0C0A (0x9A0C0A 0x00): MU_OFD_DUMMY_48 —>

<!— 9A0C0A (0x9A0C0A 0x00): Nox tailpile sensor nox signal stuck check. —>

<!— 9A0C0A (0x9A0C0A 0x00): SCR Outlet Nox Sensor — Drift Low —>

<!— 9A0C0B (0x9A0C0B 0x00): Nox out sensor rationality check for Euro VI SCR fault identification —>

<!— 9A0C0B (0x9A0C0B 0x00): SCR Outlet NOx — Rationality Error —>

<!— 9A0C0D (0x9A0C0D 0x00): SCR Outlet Nox Sensor Signal Not Available —>

<!— 9A0C0E (0x9A0C0E 0x00): MU_ISP_NOXO_CONV_RAT —>

<!— 9A0C12 (0x9A0C12 0x00): MU_RESERVE_03 —>

<!— 9A0C14 (0x9A0C14 0x00): Nox Outlet Sensor Drift Low —>

<!— 9A0C15 (0x9A0C15 0x00): Nox Outlet Sensor Drift High —>

<!— 9A1312 (0x9A1312 0x00): DOC efficiency fault —>

<!— 9A1312 (0x9A1312 0x00): MU_DPF_DOC_EFF_ERR —>

<!— 9AF0EE (0x9AF0EE 0x00): MU_FMM_TEST1 —>

<!— 9BF0EE (0x9BF0EE 0x00): MU_FMM_TEST2 —>

<!— 9CF0EE (0x9CF0EE 0x00): MU_DPS_TUBE —>

<!— 9DF0EE (0x9DF0EE 0x00): MU_DPS_MON —>

<!— 9E0003 (0x9E0003 0x00): MU_OFD_HSW_KL15_SC_UBATT_OL —>

<!— 9E0003 (0x9E0003 0x00): MU_RESERVE_06 —>

<!— 9E0004 (0x9E0004 0x00): MU_OFD_HSW_KL15_SC_GND —>

<!— 9E0004 (0x9E0004 0x00): MU_RESERVE_05 —>

<!— 9E0007 (0x9E0007 0x00): ACM Power Down — Key Off Purge Cycle —>

<!— 9EF0E9 (0x9EF0E9 0x00): MU_ISP_RESERVE_2 —>

<!— 9EF0ED (0x9EF0ED 0x00): MU_ISP_RESERVE_3 —>

<!— 9EF0FF (0x9EF0FF 0x00): MU_ISP_RESERVE_1 —>

<!— 9FF0EE (0x9FF0EE 0x00): MU_LO_DIA_SYSTEM_NO_COOL —>

<!— A0F0E3 (0xA0F0E3 0x00): MU_DPS_DIA_SPLY_ERR —>

<!— A0F0E4 (0xA0F0E4 0x00): MU_DPS_DIA_SPLY_L_ERR —>

<!— A10C07 (0xA10C07 0x00): MU_NOX_OUT_RC —>

<!— A10C07 (0xA10C07 0x00): NOx OUT Sensor ready after dewpoint enable check —>

<!— A1F0EF (0xA1F0EF 0x00): MU_DPS_T_MEA_IV_RAT —>

<!— A1F0F0 (0xA1F0F0 0x00): MU_DPS_T_MEA_ACT_RAT —>

<!— A1F0F3 (0xA1F0F3 0x00): MU_DPS_T_MEA —>

<!— A20D03 (0xA20D03 0x00): DEF Purge Lamp Circuit Failed High —>

<!— A20D04 (0xA20D04 0x00): DEF Purge Lamp Circuit Failed Low —>

<!— A20D05 (0xA20D05 0x00): DEF Purge Lamp Circuit Failed Open —>

<!— A2F0EA (0xA2F0EA 0x00): MU_ATS_DIA_RD_T_MIXER —>

<!— A40C09 (0xA40C09 0x00): Exhaust Mass Signal Not Available via CAN —>

<!— A60C02 (0xA60C02 0x00): NOx OUT Sensor not ready after dewpoint enable check —>

<!— A60E1F (0xA60E1F 0x00): CPC High Idle Regen Aborted —>

<!— A60E1F (0xA60E1F 0x00): High Idle Regen Aborted — CPC Request —>

<!— A80000 (0xA80000 0x00): Battery Voltage High —>

<!— A80000 (0xA80000 0x00): Battery voltage Signal range high —>

<!— A80001 (0xA80001 0x00): Battery Voltage Low —>

<!— A80001 (0xA80001 0x00): Battery voltage Signal range low —>

<!— AA0C00 (0xAA0C00 0x00): DOC inlet Temperature High —>

<!— AA0C00 (0xAA0C00 0x00): MU_DPF_DOC_IN_OVER_TEMP —>

<!— AA0C00 (0xAA0C00 0x00): Over temperature for the DOC —>

<!— AA0C02 (0xAA0C02 0x00): DOC Inlet Temperature Stuck (high box) —>

<!— AA0C02 (0xAA0C02 0x00): t_doc_in stuck check — high box —>

<!— AA0C03 (0xAA0C03 0x00): DOC Inlet Temperature Circuit Failed High —>

<!— AA0C04 (0xAA0C04 0x00): DOC Inlet Temperature Circuit Failed Low —>

<!— AA0C07 (0xAA0C07 0x00): MU_T_DOC_IN_MISS_OR_BYPASS —>

<!— AA0C08 (0xAA0C08 0x00): DOC Inlet Temperature — Signal Spike —>

<!— AA0C08 (0xAA0C08 0x00): Gradient of change for t_doc_in —>

<!— AA0C0A (0xAA0C0A 0x00): DOC Inlet Temperature Sensor Stuck —>

<!— AA0C0A (0xAA0C0A 0x00): t_doc_in stuck check — low box —>

<!— AA0C0D (0xAA0C0D 0x00): MU_ISP_T_DOC_IN_MCM_CAN_SNA —>

<!— AA0C0E (0xAA0C0E 0x00): MU_ATS_DIA_TDOC_IN_FIN_RAT —>

<!— AA0C11 (0xAA0C11 0x00): Diesel Oxidation Catalyst (DOC) Inlet Temperature Out Of Range Low Preventing HC Dosing —>

<!— AA0C11 (0xAA0C11 0x00): MU_ATS_DIA_HC_T_LIGHTOFF —>

<!— AA0C14 (0xAA0C14 0x00): DOC Inlet Temeperature Sensor Drifted High in Range —>

<!— AA0C14 (0xAA0C14 0x00): DOC Temperature Drift — Inlet High or Outlet Low —>

<!— AA0C15 (0xAA0C15 0x00): DOC Inlet Temperature Sensor — Plausibility Error —>

<!— AA0C15 (0xAA0C15 0x00): Rationality check for t_doc_in —>

<!— AA0C15 (0xAA0C15 0x00): Rationality check for t_doc_out —>

<!— AA0C1F (0xAA0C1F 0x00): DOC Inlet Temperature Stuck (high box) —>

<!— AA0C1F (0xAA0C1F 0x00): t_doc_in stuck check — high box —>

<!— AB0002 (0xAB0002 0x00): Ambient Air Temperature Not Plausible —>

<!— AB0002 (0xAB0002 0x00): ambient temperature sensor rationality check —>

<!— AB0002 (0xAB0002 0x00): MU_ISP_T_A_AIR_RAT —>

<!— AB0003 (0xAB0003 0x00): Ambient Air Temperature Circuit Failed High —>

<!— AB0004 (0xAB0004 0x00): Ambient Air Temperature Circuit Failed Low —>

<!— AB0008 (0xAB0008 0x00): Ambient Air Temp Signal Spike — sporadic defect on t ambient air sensor —>

<!— AB0008 (0xAB0008 0x00): Ambient Air Temp Signal Spike —>

<!— AB0008 (0xAB0008 0x00): Ambient Air Temperature sensor sporadic defect —>

<!— AB000D (0xAB000D 0x00): Ambient Air Temperature Signal Not Available via CAN —>

<!— AE0C00 (0xAE0C00 0x00): DPF Outlet Temperature High —>

<!— AE0C00 (0xAE0C00 0x00): DPF Outlet Temperature Very High —>

<!— AE0C03 (0xAE0C03 0x00): DPF Oulet Temperature Circuit Failed High —>

<!— AE0C04 (0xAE0C04 0x00): DPF Oulet Temperature Circuit Failed Low —>

<!— AE0C07 (0xAE0C07 0x00): MU_T_DPF_O_MISS_OR_BYPASS —>

<!— AE0C08 (0xAE0C08 0x00): DPF Outlet Temperature — Signal Spike —>

<!— AE0C08 (0xAE0C08 0x00): Gradient of change for t_dpf_out —>

<!— AE0C0A (0xAE0C0A 0x00): DPF Outlet Temperature Sensor Stuck —>

<!— AE0C0E (0xAE0C0E 0x00): Abnormal DPF Temperature Rise 2 —>

<!— AE0C0E (0xAE0C0E 0x00): Abnormal DPF Temperature Rise fisrt leg — uncontrolled regeneration —>

<!— AE0C0F (0xAE0C0F 0x00): DPF Outlet Temperature — High —>

<!— AE0C0F (0xAE0C0F 0x00): DPF Outlet Temperature High —>

<!— AE0C0F (0xAE0C0F 0x00): Preliminary over temperature detection for the DPF —>

<!— AE0C14 (0xAE0C14 0x00): DPF Outlet/SCR Inlet Temperature — Abnormal —>

<!— AE0C14 (0xAE0C14 0x00): DPF Outlet/SCR Inlet Temperature — Abnormal — sensor drift —>

<!— AE0C14 (0xAE0C14 0x00): DPF Temperature — DOC Outlet Low/DPF Outlet High —>

<!— AE0C15 (0xAE0C15 0x00): DOC Outlet Temperature Sensor — Plausibility Error —>

<!— AE0C15 (0xAE0C15 0x00): DPF Outlet Temperature Sensor — Plausibility Error —>

<!— AE0C15 (0xAE0C15 0x00): Rationality check for t_dpf_out —>

<!— AE0C1F (0xAE0C1F 0x00): Abnormal DPF Temperature Rise 1 —>

<!— B20C00 (0xB20C00 0x00): DOC Inboard Outlet Temperature Too High —>

<!— B20C00 (0xB20C00 0x00): DOC Outlet Temperature Very High —>

<!— B20C03 (0xB20C03 0x00): DOC Inboard Outlet Temperature Circuit Failed High —>

<!— B20C03 (0xB20C03 0x00): DOC Outlet Temperature Circuit Failed High —>

<!— B20C04 (0xB20C04 0x00): DOC Inboard Outlet Temperature Circuit Failed Low —>

<!— B20C04 (0xB20C04 0x00): DOC Outlet Temperature Circuit Failed Low —>

<!— B20C07 (0xB20C07 0x00): DOC Outlet Temperature Response Error —>

<!— B20C07 (0xB20C07 0x00): MU_T_DOC_O_MISS_OR_BYPASS —>

<!— B20C08 (0xB20C08 0x00): DOC Inboard Outlet Temperature — Signal Spike —>

<!— B20C08 (0xB20C08 0x00): DOC Outlet Temperature — Signal Spike —>

<!— B20C08 (0xB20C08 0x00): Gradient of change for t_doc_in —>

<!— B20C08 (0xB20C08 0x00): Gradient of change for t_doc_out —>

<!— B20C0A (0xB20C0A 0x00): DOC Inboard Outlet Temperature Sensor Stuck —>

<!— B20C0A (0xB20C0A 0x00): DOC Outlet Temperature Sensor Stuck —>

<!— B20C0D (0xB20C0D 0x00): MU_ISP_T_DOC_OUT_MCM_CAN_SNA —>

<!— B20C0E (0xB20C0E 0x00): Abnormal DOC Temperature Rise 2 —>

<!— B20C0E (0xB20C0E 0x00): Diagnostic for a HC leak in the exhaust pipe —>

<!— B20C0F (0xB20C0F 0x00): DOC Outlet Temperature — High —>

<!— B20C0F (0xB20C0F 0x00): DOC Outlet Temperature High —>

<!— B20C0F (0xB20C0F 0x00): Preliminary over temperature detection for the DOC —>

<!— B20C14 (0xB20C14 0x00): DOC Inboard Outlet Temperature Sensor -Drifted High in Range —>

<!— B20C14 (0xB20C14 0x00): DOC Temperature Drift — Inlet Low or Outlet High —>

<!— B20C15 (0xB20C15 0x00): DOC Inboard Outlet Temperature Sensor — Plausibility Error —>

<!— B20C15 (0xB20C15 0x00): Rationality check for t_doc_out —>

<!— B20C1F (0xB20C1F 0x00): Abnormal DOC Temperature Rise 1 —>

<!— B2140E (0xB2140E 0x00): SCR Abnormal Temperature Rise — Detect exothermie in the SCR —>

<!— B2140E (0xB2140E 0x00): SCR Abnormal Temperature Rise —>

<!— B30C00 (0xB30C00 0x00): DPF Pressure Out of Range High —>

<!— B30C00 (0xB30C00 0x00): DPF Pressure Out of Range Very High —>

<!— B30C00 (0xB30C00 0x00): Pressure drop accross the filter too high — highest level —>

<!— B30C01 (0xB30C01 0x00): DPF is missing or failed —>

<!— B30C01 (0xB30C01 0x00): DPF Pressure Out of Range Low —>

<!— B30C02 (0xB30C02 0x00): DOC Inlet Pressure Sensor — Not Plausible —>

<!— B30C02 (0xB30C02 0x00): DPF delta P signal rationality check —>

<!— B30C02 (0xB30C02 0x00): DPF Inlet/Outlet Pressure not Plausible (Driving) —>

<!— B30C0E (0xB30C0E 0x00): MU_DPF_MON_EXG_PIPE_LEAK —>

<!— B30C0F (0xB30C0F 0x00): MU_DPF_MON_DPF_PLUG_HIGH —>

<!— B30C10 (0xB30C10 0x00): DPF Pressure — Out of Range High —>

<!— B30C10 (0xB30C10 0x00): Pressure drop accross the filter too high — lowest level —>

<!— B30C14 (0xB30C14 0x00): DOC Inlet Pressure Sensor — Not Plausible —>

<!— B30C14 (0xB30C14 0x00): DPF delta P signal rationality check —>

<!— B30C15 (0xB30C15 0x00): DOC Inlet / Outlet Pressure Not Plausible —>

<!— B30C15 (0xB30C15 0x00): MU_ATS_DIA_LOW_DP_DPF_RAT —>

<!— B30C1F (0xB30C1F 0x00): Pressure drop accross the filter too high — lowest level —>

<!— B50D03 (0xB50D03 0x00): ACM Sensor Supply 1 Short to Battery —>

<!— B50D03 (0xB50D03 0x00): MU_OFD_VSENS1_SC_UBATT —>

<!— B50D04 (0xB50D04 0x00): ACM Sensor Supply 1 Short to Ground —>

<!— B50D04 (0xB50D04 0x00): MU_OFD_VSENS1_SC_GND —>

<!— B60D03 (0xB60D03 0x00): ACM Sensor Supply 2 Short to Battery —>

<!— B60D03 (0xB60D03 0x00): MU_OFD_VSENS2_SC_UBATT —>

<!— B60D04 (0xB60D04 0x00): ACM Sensor Supply 2 Short to Ground —>

<!— B60D04 (0xB60D04 0x00): MU_OFD_VSENS2_SC_GND —>

<!— B61401 (0xB61401 0x00): AMOX catalyst is aged —>

<!— B61401 (0xB61401 0x00): MU_ATS_AMOX_EFF_INTR_CHK —>

<!— B81207 (0xB81207 0x00): SCR Catalyst — Age :Limit — SCR catalyst is defect —>

<!— B81207 (0xB81207 0x00): SCR Catalyst — Age :Limit —>

<!— B8120E (0xB8120E 0x00): SCR Catalyst Aged Level 1 —>

<!— B8120E (0xB8120E 0x00): SCR Inlet Temperature High —>

<!— B8121F (0xB8121F 0x00): SCR Catalyst Aged Level 2 —>

<!— B8121F (0xB8121F 0x00): SCR Inlet Temperature Very High —>

<!— BA120E (0xBA120E 0x00): Detect the presence of the SCR —>

<!— BA120E (0xBA120E 0x00): MU_SCR_CAT_PRESENCE —>

<!— BA121F (0xBA121F 0x00): MU_OFD_DUMMY_26 —>

<!— BA121F (0xBA121F 0x00): SCR catalyst presence detection —>

<!— BB0D13 (0xBB0D13 0x00): MU_ISP_UQS_T_DEF_ERR —>

<!— BB121F (0xBB121F 0x00): DPF Outlet Temperature Response — Too fast —>

<!— BB121F (0xBB121F 0x00): DPF Pressure Differential —>

<!— BC0D01 (0xBC0D01 0x00): MU_SCR_DIA_UQS_PCT_DEF —>

<!— BC0D07 (0xBC0D07 0x00): MU_SCR_DIA_UQS_TMPR_DIAG —>

<!— BC0D09 (0xBC0D09 0x00): MU_ISP_UQS_SNA —>

<!— BC0D09 (0xBC0D09 0x00): MU_ISP_UQS_SNS_CAN_SNA —>

<!— BC0D13 (0xBC0D13 0x00): MU_ISP_UQS_CONC_DEF_ERR —>

<!— BC0D14 (0xBC0D14 0x00): MU_ISP_UQS_CONC_DRIFT_HI —>

<!— BC0D15 (0xBC0D15 0x00): MU_ISP_UQS_CONC_DRIFT_LO —>

<!— BC121F (0xBC121F 0x00): DOC Outlet Temperature Response — Too Fast —>

<!— BC121F (0xBC121F 0x00): DOC presence detection — DOC Outlet Temperature Response — Too Fast —>

<!— BD0D01 (0xBD0D01 0x00): DEF Tank Level — Zone 4 —>

<!— BD0D01 (0xBD0D01 0x00): Urea tank level check — Lim4 -Speed limiter —>

<!— BD0D09 (0xBD0D09 0x00): MU_ISP_CAN_L_DEF_TANK_SRH —>

<!— BD0D0E (0xBD0D0E 0x00): DEF Tank Level — Zone 2 —>

<!— BD0D0E (0xBD0D0E 0x00): Urea tank level check — Lim2 — Refill —>

<!— BD0D11 (0xBD0D11 0x00): DEF tank level check — Lim1 reserve —>

<!— BD0D11 (0xBD0D11 0x00): Urea tank level check — Lim1 reserve —>

<!— BD0D12 (0xBD0D12 0x00): DEF Tank Level — Zone 3 —>

<!— BD0D12 (0xBD0D12 0x00): Urea tank level check — Lim3 -Torque limiter —>

<!— BD0D13 (0xBD0D13 0x00): DEF Tank Signal Erratic via CAN —>

<!— BD0D13 (0xBD0D13 0x00): MU_ISP_CAN_L_DEF_TANK_ERR —>

<!— BD0D1F (0xBD0D1F 0x00): MU_TRC_L_DEF_TANK_LIM_5 —>

<!— BE0009 (0xBE0009 0x00): Engine Speed Signal Not Available via CAN —>

<!— C10D1F (0xC10D1F 0x00): MU_SCR_DIA_UQS_IS_DIESEL —>

<!— C1150C (0xC1150C 0x00): MU_DPS_T_SENS —>

<!— C1150E (0xC1150E 0x00): MU_DPS_TEMP —>

<!— C30D08 (0xC30D08 0x00): MU_DPF_FFAC_ERR —>

<!— C30D08 (0xC30D08 0x00): Regen Frequency Error —>

<!— D00C00 (0xD00C00 0x00): DPF Outlet Temperature High (Bank 2) —>

<!— D00C03 (0xD00C03 0x00): MU_ISP_DUMMY_04_SRH —>

<!— D00C04 (0xD00C04 0x00): MU_ISP_DUMMY_04_SRL —>

<!— D00C0E (0xD00C0E 0x00): Abnormal DPF Temperature Rise seccond leg — uncontrolled regeneration —>

<!— D00C0E (0xD00C0E 0x00): MU_DPF_UNCNTRL_REGENB —>

<!— D00C15 (0xD00C15 0x00): MU_ATS_DIA_DUMMY_01 —>

<!— D40C00 (0xD40C00 0x00): DOC Outlet Temperature High (Bank 2) —>

<!— D40C03 (0xD40C03 0x00): DOC Outboard Outlet Temperature Circuit Failed High —>

<!— D40C04 (0xD40C04 0x00): DOC Outboard Outlet Temperature Circuit Failed Low —>

<!— D40C08 (0xD40C08 0x00): DOC Outboard Outlet Temperature — Signal Spike —>

<!— D40C08 (0xD40C08 0x00): Gradient of change for t_doc_out b —>

<!— D40C0A (0xD40C0A 0x00): DOC Outboard Outlet Temperature Sensor Stuck —>

<!— D40C0E (0xD40C0E 0x00): MU_DPF_Q_DOT_DOCB_ERR —>

<!— D40C0F (0xD40C0F 0x00): MU_DPF_DOCB_OVERTEMP_WRN —>

<!— D40C0F (0xD40C0F 0x00): MU_OFD_DUMMY_32 —>

<!— D40C0F (0xD40C0F 0x00): Preliminary over temperature for the DOC —>

<!— D40C15 (0xD40C15 0x00): DOC Outboard Outlet Temperature Sensor — Plausibility Error —>

<!— D40C15 (0xD40C15 0x00): DPF Outlet Temperature Sensor — Not Plausible —>

<!— D40C15 (0xD40C15 0x00): Rationality check for t_docb_out —>

<!— D70B00 (0xD70B00 0x00): SCR Temperature of Tank is Too High —>

<!— D70B02 (0xD70B02 0x00): DEF Tank Temperature Drift in Range —>

<!— D70B03 (0xD70B03 0x00): DEF Tank Temeprature Sensor Circuit Failed High —>

<!— D70B03 (0xD70B03 0x00): DEF Tank Temperature Sensor Circuit Failed High —>

<!— D70B04 (0xD70B04 0x00): DEF Tank Temeprature Sensor Circuit Failed Low —>

<!— D70B04 (0xD70B04 0x00): DEF Tank Temperature Sensor Circuit Failed Low —>

<!— D70B09 (0xD70B09 0x00): DEF Tank Temperature Signal Not Available via CAN —>

<!— D70B09 (0xD70B09 0x00): MU_ISP_CAN_T_DEF_TANK_SRH —>

<!— D70B0A (0xD70B0A 0x00): Reductant Tank Temperature Sensor Circuit Range/Performance —>

<!— D70B0D (0xD70B0D 0x00): DEF Tank Temperature Signal Not Available via CAN —>

<!— D70B13 (0xD70B13 0x00): DEF Tank Temperature Error (CAN) —>

<!— D70B13 (0xD70B13 0x00): MU_ISP_CAN_T_DEF_TANK_ERR —>

<!— E10600 (0xE10600 0x00): DEF tank level check — Lim1 reserve —>

<!— E10600 (0xE10600 0x00): MU_TRC_L_DEF_TANK_SRL —>

<!— E10600 (0xE10600 0x00): MU_TRC_L_UREA_TANK_LIM_1 —>

<!— E10600 (0xE10600 0x00): Urea tank level check — Lim1 reserve —>

<!— E10601 (0xE10601 0x00): DEF Tank Level 0 — Empty (Speed Limited) —>

<!— E10601 (0xE10601 0x00): DEF Tank Zone 0 Condition (Speed Limit) —>

<!— E10602 (0xE10602 0x00): DEF Level Sensor Error —>

<!— E10602 (0xE10602 0x00): MU_SCR_DIA_L_DEF_TANK_RAT —>

<!— E10603 (0xE10603 0x00): DEF Tank Level Sensor Circuit Failed High —>

<!— E10604 (0xE10604 0x00): DEF Tank Level Sensor Circuit Failed Low —>

<!— E10609 (0xE10609 0x00): DEF tank level signal not available —>

<!— E10609 (0xE10609 0x00): MU_ISP_DEF_TANK_LVL_SNA —>

<!— E1060D (0xE1060D 0x00): MU_ISP_SEL_L_DEF_TANK —>

<!— E1060D (0xE1060D 0x00): MU_ISP_SEL_L_UREA_TANK —>

<!— E1060D (0xE1060D 0x00): tank level curve not selected. —>

<!— E1060E (0xE1060E 0x00): DEF Level Sensor Error —>

<!— E1060E (0xE1060E 0x00): DEF Tank Level 2 — Very Low —>

<!— E10611 (0xE10611 0x00): DEF Tank Level 2 — Very Low —>

<!— E10611 (0xE10611 0x00): DEF Tank Zone 2 Condition —>

<!— E10611 (0xE10611 0x00): MU_SCR_DIA_DEF_LEVEL_LOW —>

<!— E10612 (0xE10612 0x00): DEF Tank Level 1 — Empty —>

<!— E10612 (0xE10612 0x00): DEF Tank Zone 1 Condition —>

<!— E1061F (0xE1061F 0x00): DEF Tank Level 3 — Low —>

<!— E1061F (0xE1061F 0x00): DEF Tank Zone 3 Condition —>

<!— E40D00 (0xE40D00 0x00): Over fuelling of the HC doser —>

<!— E40D00 (0xE40D00 0x00): Regen Temperature — Out of Range High —>

<!— E40D01 (0xE40D01 0x00): Insufficent fuelling of the hc doser —>

<!— E40D01 (0xE40D01 0x00): Regen Temperature — Out of Range Low —>

<!— E40D12 (0xE40D12 0x00): DOC Outlet Temp Low (Low Temp Regen) —>

<!— EA0B00 (0xEA0B00 0x00): DOC plugged —>

<!— EA0B00 (0xEA0B00 0x00): Engine Air Flow Out of Range Low —>

<!— EA0B01 (0xEA0B01 0x00): Active Regen Temp Out of Range Low —>

<!— EA0B01 (0xEA0B01 0x00): DOC is missing or failed —>

<!— EB0B1F (0xEB0B1F 0x00): Determine the aging effect on SCR —>

<!— EB0B1F (0xEB0B1F 0x00): MU_SCR_MOD_SCR_AGE —>

<!— EB1010 (0xEB1010 0x00): MU_DEF_DLVRY_OVER_DOS —>

<!— EB1012 (0xEB1012 0x00): MU_DEF_DLVRY_UNDER_DOS —>

<!— EC101F (0xEC101F 0x00): DOC inlet temperature out of range low preventing hc dosing —>

<!— EC101F (0xEC101F 0x00): MU_ATS_DIA_COLD_THAW —>

<!— ED000D (0xED000D 0x00): ACM ECU has detected an exchange of MCM or ACM ECU —>

<!— ED000D (0xED000D 0x00): MU_DIAG_ECU_EXCHANGE —>

<!— EE1002 (0xEE1002 0x00): DEF Pressure Sensor Drift in Range —>

<!— EE1003 (0xEE1003 0x00): DEF Pressure Sensor Circuit Failed High —>

<!— EE1004 (0xEE1004 0x00): DEF Pressure Sensor Circuit Failed Low —>

<!— EE1005 (0xEE1005 0x00): DEF Pressure Sensor not Plausible —>

<!— EE1007 (0xEE1007 0x00): DEF Pressure Low —>

<!— EE1007 (0xEE1007 0x00): Urea pressure too low. Block urea supply line,urea leakage in the system, bad air purging of the urea supply system —>

<!— EE1008 (0xEE1008 0x00): DEF Pressure sensor sporadic defect —>

<!— EE1008 (0xEE1008 0x00): DEF Pressure Signal Spike — sporadic defect on p urea sensor —>

<!— EE1008 (0xEE1008 0x00): DEF Pressure Signal Spike —>

<!— EE100A (0xEE100A 0x00): Def Acumulator Failure —>

<!— EE100A (0xEE100A 0x00): Urea pressure out of working range (air assisted system) —>

<!— EE1011 (0xEE1011 0x00): DEF Discharge Pressure High —>

<!— EE1011 (0xEE1011 0x00): DEF Purge Pressure High —>

<!— EE1011 (0xEE1011 0x00): Urea pressure drop too low Prevent Urea cristal formation and freezing protection in the urea system through cycling the air supply on/off —>

<!— EE1011 (0xEE1011 0x00): Urea pressure drop too low. Prevent Urea cristal formation and freezing protection in the urea system through cycling the air supply on/off —>

<!— EF1001 (0xEF1001 0x00): Air pressure Sensor Urea system Signal range low —>

<!— EF1001 (0xEF1001 0x00): DEF Air Pressure Not Detected (from vehicle supply) —>

<!— EF1002 (0xEF1002 0x00): DEF Air Pressure Sensor Dift in Range —>

<!— EF1002 (0xEF1002 0x00): DEF Air Pressure Sensor Drift —>

<!— EF1003 (0xEF1003 0x00): DEF Air Pressure Sensor Circuit Failed High —>

<!— EF1004 (0xEF1004 0x00): DEF Air Pressure Sensor Circuit Failed Low —>

<!— EF1005 (0xEF1005 0x00): DEF Air Pressure Sensor not Plausible —>

<!— EF1007 (0xEF1007 0x00): Check Internal air pressure line in the channel to the sensor —>

<!— EF1007 (0xEF1007 0x00): Check Internal air pressure line in the diffuser to the sensor —>

<!— EF1007 (0xEF1007 0x00): DEF Air Pressure Air Low —>

<!— EF1007 (0xEF1007 0x00): DEF Air Pressure Low —>

<!— EF1008 (0xEF1008 0x00): Air Pressure sensor sporadic defect —>

<!— EF1008 (0xEF1008 0x00): DEF Air Pressure Signal Spike — sporadic defect on p air sensor —>

<!— EF1008 (0xEF1008 0x00): DEF Air Pressure Signal Spike —>

<!— EF100E (0xEF100E 0x00): Air pressure Sensor Urea system Signal range High —>

<!— EF100E (0xEF100E 0x00): DEF — Information Only —>

<!— EF100E (0xEF100E 0x00): DEF Air Pressure High —>

<!— EF101F (0xEF101F 0x00): Check Internal air pressure line in the diffuser to the sensor —>

<!— EF101F (0xEF101F 0x00): DEF — Information Only —>

<!— F00B02 (0xF00B02 0x00): MU_OFD_DUMMY_28 —>

<!— F00B02 (0xF00B02 0x00): Nox raw sensor lambda signal rationality check —>

<!— F00B02 (0xF00B02 0x00): SCR Inlet Nox Sensor — Error —>

<!— F01003 (0xF01003 0x00): Air control valve for the urea air assited system -short to battery —>

<!— F01003 (0xF01003 0x00): DEF Air Valve Circuit Failed High —>

<!— F01003 (0xF01003 0x00): Pressure Limiting Unit Circuit Failed High —>

<!— F01004 (0xF01004 0x00): Air control valve for the urea air assited system -short to ground —>

<!— F01004 (0xF01004 0x00): DEF Air Valve Circuit Failed Low —>

<!— F01004 (0xF01004 0x00): Pressure Limiting Unit Circuit Failed Low —>

<!— F01005 (0xF01005 0x00): Air control valve for the urea air assited system -Open Loop —>

<!— F01005 (0xF01005 0x00): Air control valve for the urea air assited system -Open load —>

<!— F01005 (0xF01005 0x00): DEF Air Valve Circuit Failed Open —>

<!— F01005 (0xF01005 0x00): Pressure Limiting Unit Circuit Failed Open —>

<!— F10B02 (0xF10B02 0x00): MU_OFD_DUMMY_29 —>

<!— F10B02 (0xF10B02 0x00): Nox out sensor lambda signal rationality check —>

<!— F10B02 (0xF10B02 0x00): SCR Outlet Nox Sensor — Error —>

<!— F11000 (0xF11000 0x00): DEF dosing system is not cooled —>

<!— F11000 (0xF11000 0x00): MU_EDU_DOS_SYS_UNCOOLED —>

<!— F11000 (0xF11000 0x00): Urea dosing system is not cooled —>

<!— F11001 (0xF11001 0x00): SCR_ADS system Frozen —>

<!— F11001 (0xF11001 0x00): Torque limitation if the system can not be cooled (e.g., the urea line is frozen in cold environment.) —>

<!— F11001 (0xF11001 0x00): Torque limitation if the system can not be cooled — e.g., the urea line is frozen in cold environment. —>

<!— F11002 (0xF11002 0x00): DEF Dosing Unit Temperature Drift in Range —>

<!— F11003 (0xF11003 0x00): DEF Temeprature Sensor Circuit Failed High —>

<!— F11003 (0xF11003 0x00): DEF Temperature Sensor Circuit Failed High —>

<!— F11004 (0xF11004 0x00): DEF Temeprature Sensor Circuit Failed Low —>

<!— F11004 (0xF11004 0x00): DEF Temperature Sensor Circuit Failed Low —>

<!— F20E00 (0xF20E00 0x00): Long term DEF consumption too high —>

<!— F20E00 (0xF20E00 0x00): Long term Urea consumption too high —>

<!— F20E00 (0xF20E00 0x00): MU_UCM_DEF_CONSUM_AVE_SRH —>

<!— F20E00 (0xF20E00 0x00): MU_UCM_UREA_CONSUM_AVE_SRH —>

<!— F20E01 (0xF20E01 0x00): Long term DEF consumption too low —>

<!— F20E01 (0xF20E01 0x00): Long term Urea consumption too low —>

<!— F20E01 (0xF20E01 0x00): MU_UCM_DEF_CONSUM_AVE_SRL —>

<!— F20E01 (0xF20E01 0x00): MU_UCM_UREA_CONSUM_AVE_SRL —>

<!— F31007 (0xF31007 0x00): MU_DPF_FB_CTRL_ERR —>

<!— F40E00 (0xF40E00 0x00): MU_UCM_DEF_CONSUM_ACT_SRH —>

<!— F40E00 (0xF40E00 0x00): MU_UCM_UREA_CONSUM_ACT_SRH —>

<!— F40E00 (0xF40E00 0x00): Short term DEF consumption too high —>

<!— F40E00 (0xF40E00 0x00): Short term Urea consumption too high —>

<!— F40E01 (0xF40E01 0x00): MU_UCM_DEF_CONSUM_ACT_SRL —>

<!— F40E01 (0xF40E01 0x00): MU_UCM_UREA_CONSUM_ACT_SRL —>

<!— F40E01 (0xF40E01 0x00): Short term DEF consumption too low —>

<!— F40E01 (0xF40E01 0x00): Short term Urea consumption too low —>

<!— F40E0F (0xF40E0F 0x00): MU_UCM_SC_CONSUM_SRH —>

<!— F40E11 (0xF40E11 0x00): MU_UCM_SC_CONSUM_SRL —>

<!— F80B07 (0xF80B07 0x00): DPF regeneration can not be terminated in time — infenite regeneration. —>

<!— F80B07 (0xF80B07 0x00): High Idle Regeneration Not Complete —>

<!— F80B0D (0xF80B0D 0x00): DPF System Parametrization Failure —>

<!— F80B0E (0xF80B0E 0x00): Pressure drop accross the filter too low —>

<!— FE0F1F (0xFE0F1F 0x00): Adblue dilution detection —>

<!— FE0F1F (0xFE0F1F 0x00): Improper DEF Quality —>

<!— FE0F1F (0xFE0F1F 0x00): Improper DEF Quality by regeneration —>

<!— 00F0EE (0x00F0EE 0x00): MU_PROTO_01 —>

<!— 010209 (0x010209 0x00): Actual Torque Signal Not Available via CAN —>

<!— 011103 (0x011103 0x00): Dosing Unit Heater Circuit Failed High —>

<!— 011104 (0x011104 0x00): Dosing Unit Heater Circuit Failed Low —>

<!— 011105 (0x011105 0x00): Dosing Unit Heater Open Circuit —>

<!— 01F0EE (0x01F0EE 0x00): MU_PROTO_02 —>

<!— 021103 (0x021103 0x00): SCR Line Heater #1 Circuit Failed High —>

<!— 021104 (0x021104 0x00): SCR Line Heater #1 Circuit Failed Low —>

<!— 021105 (0x021105 0x00): SCR Line Heater #1 Open Circuit —>

<!— 02F0EE (0x02F0EE 0x00): MU_PROTO_03 —>

<!— 031103 (0x031103 0x00): SCR Line Heater #2 Circuit Failed High —>

<!— 031104 (0x031104 0x00): SCR Line Heater #2 Circuit Failed Low —>

<!— 031105 (0x031105 0x00): SCR Line Heater #2 Circuit Failed Open —>

<!— 03F0EE (0x03F0EE 0x00): MU_PROTO_04 —>

<!— 04100D (0x04100D 0x00): MCM/ACM Software Not Compatible —>

<!— 041103 (0x041103 0x00): SCR Line Heater #3 Circuit Failed High —>

<!— 041104 (0x041104 0x00): SCR Line Heater #3 Circuit Failed Low —>

<!— 041105 (0x041105 0x00): SCR Line Heater #3 Circuit Failed Open —>

<!— 04F0EE (0x04F0EE 0x00): MU_PROTO_05 —>

<!— 051103 (0x051103 0x00): SCR Line Heater #4 Circuit Failed High —>

<!— 051104 (0x051104 0x00): SCR Line Heater #4 Circuit Failed Low —>

<!— 051105 (0x051105 0x00): SCR Line Heater #4 Circuit Failed Open —>

<!— 05F0EE (0x05F0EE 0x00): MU_PROTO_06 —>

<!— 06F0EE (0x06F0EE 0x00): MU_PROTO_07 —>

<!— 081102 (0x081102 0x00): Selective Catalyst Reduction Inlet Temperature — Not Plausible —>

<!— 081103 (0x081103 0x00): SCR Inlet Temperature Sensor Circuit Failed High —>

<!— 081104 (0x081104 0x00): SCR Inlet Temperature Sensor Circuit Failed Low —>

<!— 081108 (0x081108 0x00): SCR Inlet Temperature — Signal Spike —>

<!— 08110A (0x08110A 0x00): SCR Inlet Temperature Sensor — Rationality Error —>

<!— 08110F (0x08110F 0x00): SCR Inlet Temperature High —>

<!— 081114 (0x081114 0x00): SCR Inlet Temperature Sensor Drift High in Range —>

<!— 081115 (0x081115 0x00): SCR Inlet Temperature Drift in Range —>

<!— 08F0EF (0x08F0EF 0x00): Reserved_MU_435 MU not in use —>

<!— 090402 (0x090402 0x00): ACM2.1 engine hours data erratic, intermittent or incorrect —>

<!— 09F0E3 (0x09F0E3 0x00): MU_RESERVE_09_E5 —>

<!— 09F0EE (0x09F0EE 0x00): MU_DPS_TEMP —>

<!— 09F0EF (0x09F0EF 0x00): MU_RESERVE_08_E5 —>

<!— 09F0F1 (0x09F0F1 0x00): MU_RESERVE_11_E5 —>

<!— 09F0F3 (0x09F0F3 0x00): MU_RESERVE_10_E5 —>

<!— 0AF0EE (0x0AF0EE 0x00): MU_DPF_RESERVE1 —>

<!— 0B1100 (0x0B1100 0x00): SCR Outlet Temperature High —>

<!— 0B1103 (0x0B1103 0x00): SCR Outlet Temperature Sensor Circuit Failed High —>

<!— 0B1104 (0x0B1104 0x00): SCR Outlet Temperature Sensor Circuit Failed Low —>

<!— 0B1107 (0x0B1107 0x00): SCR Outlet Temperature Sensor Out of Range High —>

<!— 0B1108 (0x0B1108 0x00): SCR Outlet Temperature — Signal Spike —>

<!— 0B110A (0x0B110A 0x00): SCR Outlet Temperature Sensor — Rationality Error —>

<!— 0B1114 (0x0B1114 0x00): SCR Temperature Drift — Inlet Low/Outlet High —>

<!— 0B1115 (0x0B1115 0x00): SCR Outlet Temperature Drift in Range —>

<!— 0BF0EE (0x0BF0EE 0x00): MU_DPF_RESERVE2 —>

<!— 0C1101 (0x0C1101 0x00): SCR NOX Conversion Efficiency Very Low —>

<!— 0C110E (0x0C110E 0x00): SCR catalyst nox conversion rate check —>

<!— 0C1112 (0x0C1112 0x00): SCR NOX Conversion Efficiency Low —>

<!— 0C111F (0x0C111F 0x00): SCR Nox Efficiency Low —>

<!— 0CF0EE (0x0CF0EE 0x00): MU_DPF_RESERVE3 —>

<!— 0D0E03 (0x0D0E03 0x00): High Side Digital Output 1 Circuit Failed High —>

<!— 0D0E04 (0x0D0E04 0x00): High Side Digital Output 1 Circuit Failed Low —>

<!— 0DF0EE (0x0DF0EE 0x00): MU_DPF_RESERVE4 —>

<!— 0E0E03 (0x0E0E03 0x00): High Side Digital Output 2 Circuit Failed High —>

<!— 0E0E04 (0x0E0E04 0x00): High Side Digital Output 2 Circuit Failed Low —>

<!— 0EF0EE (0x0EF0EE 0x00): MU_DPF_RESERVE5 —>

<!— 0F0E03 (0x0F0E03 0x00): High Side Digital Output 3 Circuit Failed High —>

<!— 0F0E04 (0x0F0E04 0x00): High Side Digital Output 3 Circuit Failed Low —>

<!— 0FF0EE (0x0FF0EE 0x00): MU_DPF_RESERVE6 —>

<!— 10F0EE (0x10F0EE 0x00): MU_DPF_RESERVE7 —>

<!— 151500 (0x151500 0x00): Regeneration Frequency Error — Severe —>

<!— 15150B (0x15150B 0x00): Check if Kalman request a regeneration before the fixed trigger and very late in zone 0 —>

<!— 15150E (0x15150E 0x00): Check if Kalman request a regeneration before the fixed trigger and very early in zone 0 — it is a smoky engine —>

<!— 151510 (0x151510 0x00): Regeneration Frequency Error — Moderate —>

<!— 15151F (0x15151F 0x00): DPF Regen Too Often —>

<!— 161100 (0x161100 0x00): Under pressurized DEF system —>

<!— 161101 (0x161101 0x00): Over pressurized DEF system —>

<!— 161102 (0x161102 0x00): pump speed difference between high and low dosing amounts is to small —>

<!— 161103 (0x161103 0x00): pump speed signal over measurement range —>

<!— 161104 (0x161104 0x00): pump speed signal below measurement range —>

<!— 161113 (0x161113 0x00): DEF system is not being controlled as expected —>

<!— 171103 (0x171103 0x00): DEF Pump Circuit Failed High —>

<!— 171104 (0x171104 0x00): DEF Pump Circuit Failed Low —>

<!— 171105 (0x171105 0x00): DEF Pump Circuit Failed Open —>

<!— 171106 (0x171106 0x00): DEF Pump Supply Current High —>

<!— 171510 (0x171510 0x00): HC Dosing Quantity —>

<!— 17151F (0x17151F 0x00): MU_DPF_HC_BRNOFF_REQ —>

<!— 190E03 (0x190E03 0x00): DOC Inlet Pressure Circuit Failed High —>

<!— 190E04 (0x190E04 0x00): DOC Inlet Pressure Circuit Failed Low —>

<!— 190E08 (0x190E08 0x00): DOC Inlet Pressure Signal Spike —>

<!— 190E0A (0x190E0A 0x00): DOC Inlet Pressure Sensor Stuck —>

<!— 190E0E (0x190E0E 0x00): MU_DPF_DOC_CLN_UP_P_FAULT —>

<!— 190E15 (0x190E15 0x00): DPF Inlet Pressure — Drift Low —>

<!— 191100 (0x191100 0x00): SCR Outlet NOx High — Non Fueling —>

<!— 1A0E00 (0x1A0E00 0x00): DPF System Back Pressure Too High —>

<!— 1A0E02 (0x1A0E02 0x00): DPF Outlet Pressure Sensor — Not Plausible —>

<!— 1A0E03 (0x1A0E03 0x00): DPF Outlet Pressure Circuit Failed High —>

<!— 1A0E04 (0x1A0E04 0x00): DPF Outlet Pressure Circuit Failed Low —>

<!— 1A0E07 (0x1A0E07 0x00): DPF Outlet Pressure High —>

<!— 1A0E08 (0x1A0E08 0x00): DPF Outlet Pressure Signal Spike —>

<!— 1A0E0A (0x1A0E0A 0x00): DPF Outlet Pressure Sensor Stuck —>

<!— 1A0E0E (0x1A0E0E 0x00): DPF backpressure too low —>

<!— 1A0E0F (0x1A0E0F 0x00): DPF Backpressure Signal Range High —>

<!— 1A0E15 (0x1A0E15 0x00): DPF Outlet Pressure — Drift Low —>

<!— 210D00 (0x210D00 0x00): DEF Dosing Valve Stuck Open —>

<!— 210D01 (0x210D01 0x00): DEF Dosing Valve Stuck Closed —>

<!— 210D03 (0x210D03 0x00): DEF Dosing Valve Circuit Failed High —>

<!— 210D04 (0x210D04 0x00): DEF Dosing Valve Circuit Failed Low —>

<!— 210D05 (0x210D05 0x00): DEF Dosing Valve Circuit Failed Open —>

<!— 210D07 (0x210D07 0x00): MU_LO_DSR_IOP_AUTO_INCMPT —>

<!— 210D08 (0x210D08 0x00): DEF Metering Unit — Exceeded Unclog Attempts —>

<!— 210D0D (0x210D0D 0x00): DEF Dosing Correction Factor Not Available via CAN —>

<!— 210D0E (0x210D0E 0x00): DEF System not on standby —>

<!— 210D1F (0x210D1F 0x00): Dosing Unit Error —>

<!— 230D00 (0x230D00 0x00): DEF Tank Temperature — High —>

<!— 230D01 (0x230D01 0x00): DEF Tank Temperature — Low —>

<!— 230D03 (0x230D03 0x00): DEF Coolant Valve Circuit Failed High —>

<!— 230D04 (0x230D04 0x00): DEF Coolant Valve Circuit Failed Low —>

<!— 230D05 (0x230D05 0x00): DEF Coolant Valve Circuit Failed Open —>

<!— 230D07 (0x230D07 0x00): DEF Tank Temperature Too Low —>

<!— 230D1F (0x230D1F 0x00): DEF Tank Temperature Too High —>

<!— 240D01 (0x240D01 0x00): Improper DEF Quality Final Warning —>

<!— 240D02 (0x240D02 0x00): Improper DEF Quality —>

<!— 240D11 (0x240D11 0x00): Improper DEF Quality Warning —>

<!— 240D12 (0x240D12 0x00): Improper DEF Quality — Moderately severe —>

<!— 28F0E9 (0x28F0E9 0x00): NOx Mass Signal Not Available via CAN —>

<!— 2DF0EE (0x2DF0EE 0x00): MLIT Case1 Inducement — Dosing activity error —>

<!— 2EF0EE (0x2EF0EE 0x00): CAN Parity signal and vehicle mileage not available —>

<!— 2FF0E3 (0x2FF0E3 0x00): MU_ISP_RES_DPF_1_SRH —>

<!— 2FF0E4 (0x2FF0E4 0x00): MU_ISP_RES_DPF_1_SRL —>

<!— 30F0E3 (0x30F0E3 0x00): MU_ISP_RES_DPF_2_SRH —>

<!— 30F0E4 (0x30F0E4 0x00): MU_ISP_RES_DPF_2_SRL —>

<!— 31F0E3 (0x31F0E3 0x00): MU_ISP_RES_SCR_1_SRH —>

<!— 31F0E4 (0x31F0E4 0x00): MU_ISP_RES_SCR_1_SRL —>

<!— 32F0E3 (0x32F0E3 0x00): MU_ISP_RES_SCR_2_SRH —>

<!— 32F0E4 (0x32F0E4 0x00): MU_ISP_RES_SCR_2_SRL —>

<!— 33F0E3 (0x33F0E3 0x00): MU_ISP_RES_SCR_3_SRH —>

<!— 33F0E4 (0x33F0E4 0x00): MU_ISP_RES_SCR_3_SRL —>

<!— 34F0E3 (0x34F0E3 0x00): MU_ISP_SOOT_SENS_SRH —>

<!— 34F0E4 (0x34F0E4 0x00): MU_ISP_SOOT_SENS_SRL —>

<!— 36F0E3 (0x36F0E3 0x00): MU_ISP_DUMMY_02_SRH —>

<!— 36F0E4 (0x36F0E4 0x00): MU_ISP_DUMMY_02_SRL —>

<!— 38F0E3 (0x38F0E3 0x00): MU_ISP_RSP_01_DPF_SRH —>

<!— 38F0E4 (0x38F0E4 0x00): MU_ISP_RSP_01_DPF_SRL —>

<!— 3B1507 (0x3B1507 0x00): Non DEF flow situation —>

<!— 3CF0EE (0x3CF0EE 0x00): DEF Tank Zone 4 Condition —>

<!— 3CF0F2 (0x3CF0F2 0x00): MLIT Case2 Inducement — Low Diesel-Exhaust-Fuel tank —>

<!— 3CF0FF (0x3CF0FF 0x00): DEF Tank Zone 5 Condition —>

<!— 3D1103 (0x3D1103 0x00): MU_ISP_RSP_01_SCR_SRH —>

<!— 3D1104 (0x3D1104 0x00): MU_ISP_RSP_01_SCR_SRL —>

<!— 41F0F2 (0x41F0F2 0x00): HC Slip is too high —>

<!— 431500 (0x431500 0x00): DPF HC Absorption Very High —>

<!— 43150F (0x43150F 0x00): DPF HC Absorption Warning —>

<!— 431510 (0x431510 0x00): DPF HC Absorption High —>

<!— 44F0EE (0x44F0EE 0x00): ATS Not Started Up —>

<!— 45F0EE (0x45F0EE 0x00): ACM Not Parameterized —>

<!— 4DF0E8 (0x4DF0E8 0x00): Input Signal Spike 1 —>

<!— 4EF0E8 (0x4EF0E8 0x00): Input Signal Spike 2 —>

<!— 55F0FF (0x55F0FF 0x00): MU_DPF_MON_TIME_EST_INT —>

<!— 57F0E2 (0x57F0E2 0x00): EDU DEF temperature sensor signal drift —>

<!— 57F0E3 (0x57F0E3 0x00): EDU Temperature Sensor Signal Failed High —>

<!— 57F0E4 (0x57F0E4 0x00): EDU Temperature Sensor Signal Failed Low —>

<!— 58F0E3 (0x58F0E3 0x00): EDU Pressure Sensor Signal Failed High —>

<!— 58F0E4 (0x58F0E4 0x00): EDU Pressure Sensor Signal Failed Low —>

<!— 59F0E3 (0x59F0E3 0x00): EDU sensor supply signal range high. —>

<!— 59F0E4 (0x59F0E4 0x00): EDU sensor supply signal range low. —>

<!— 5AF0E3 (0x5AF0E3 0x00): EDU Dosing Valve Signal Failed High —>

<!— 5AF0E4 (0x5AF0E4 0x00): EDU Dosing Valve Signal Failed Low —>

<!— 5AF0E5 (0x5AF0E5 0x00): EDU Dosing Valve Signal Failed Open —>

<!— 5BF0E3 (0x5BF0E3 0x00): EDU DEF heater shortcut to battery —>

<!— 5BF0E4 (0x5BF0E4 0x00): EDU DEF heater shortcut to ground —>

<!— 5BF0E5 (0x5BF0E5 0x00): Heater of EDU open load —>

<!— 5CF0E3 (0x5CF0E3 0x00): EDU high side switch 1 -pump and heater- shortcut to battery —>

<!— 5CF0E4 (0x5CF0E4 0x00): EDU high side switch 1 -pump and heater shortcut to ground —>

<!— 5DF0E3 (0x5DF0E3 0x00): EDU high side switch 2 -pump and heater- shortcut to battery —>

<!— 5DF0E4 (0x5DF0E4 0x00): EDU high side switch 2 -pump and heater- shortcut to ground —>

<!— 5EF0E3 (0x5EF0E3 0x00): EDU battery signal range high —>

<!— 5EF0E4 (0x5EF0E4 0x00): EDU battery signal range low —>

<!— 5F0402 (0x5F0402 0x00): Air fuel ratio rationality check —>

<!— 5FF0E9 (0x5FF0E9 0x00): ACM DM1 Message Not Received at Dash Cluster —>

<!— 600F07 (0x600F07 0x00): Incomplete Regeneration —>

<!— 600F11 (0x600F11 0x00): DPF Efficiency Check —>

<!— 600F12 (0x600F12 0x00): DPF Pressure — Out of Range Low —>

<!— 61F0E3 (0x61F0E3 0x00): EDU DEF pump schortcut to battery —>

<!— 61F0E4 (0x61F0E4 0x00): EDU DEF pump schortcut to ground —>

<!— 61F0E5 (0x61F0E5 0x00): EDU DEF pump open load —>

<!— 620103 (0x620103 0x00): Relative Humidity Sensor Circuit Failed High —>

<!— 620104 (0x620104 0x00): Relative Humidity Sensor Circuit Failed Low —>

<!— 62F0F1 (0x62F0F1 0x00): EDU DEF filter service requirement —>

<!— 62F0F2 (0x62F0F2 0x00): EDU DEF filter life time expired — service routine —>

<!— 63F0E0 (0x63F0E0 0x00): EDU DEF pump speed too high —>

<!— 63F0E1 (0x63F0E1 0x00): EDU DEF pump speed too low —>

<!— 63F0E2 (0x63F0E2 0x00): Too small difference of DEF pump speed at low respectively at high dosing amounts —>

<!— 63F0E7 (0x63F0E7 0x00): EDU DEF pump is blocked —>

<!— 63F0F3 (0x63F0F3 0x00): DEF pump is not running synchronous —>

<!— 65F0EC (0x65F0EC 0x00): EDU ECU internal fault —>

<!— 65F0ED (0x65F0ED 0x00): EDU memory check failed —>

<!— 66F0E7 (0x66F0E7 0x00): Pressure relief valve is stuck closed —>

<!— 67F0FF (0x67F0FF 0x00): EDU pump speed signal range low. —>

<!— 68F0ED (0x68F0ED 0x00): EDU dataset is not valid —>

<!— 6AF0E0 (0x6AF0E0 0x00): MU_ATS_DIA_EDU_OVER_TEMP —>

<!— 6AF0E9 (0x6AF0E9 0x00): DEF Doser (EDU) CAN Signal Missing —>

<!— 6AF0EF (0x6AF0EF 0x00): Uncooled DEF system, EDU Hot —>

<!— 6AF0F0 (0x6AF0F0 0x00): Uncooled DEF system, EDU hot high —>

<!— 6C000D (0x6C000D 0x00): Ambient Air Pressure Signal Not Available via CAN —>

<!— 6D1604 (0x6D1604 0x00): Soot Sensor Probe short circuit —>

<!— 6D1609 (0x6D1609 0x00): Soot Sensor communication error —>

<!— 6D160C (0x6D160C 0x00): Soot Sensor Probe self diagnostic —>

<!— 6D160D (0x6D160D 0x00): Soot Sensor CAN Signal Missing —>

<!— 6D1610 (0x6D1610 0x00): Soot Sensor Data Valid But Above Normal Operating Range — Moderately Severe Level —>

<!— 6D1611 (0x6D1611 0x00): MU_RESERVE_03_E5 —>

<!— 6D1612 (0x6D1612 0x00): Soot Sensor Data Valid But Below Normal Operating Range — Moderately Severe Level —>

<!— 6E0009 (0x6E0009 0x00): Coolant Temperature Signal Not Available via CAN —>

<!— 701503 (0x701503 0x00): SCR Line Heater #5 Circuit Failed High —>

<!— 701504 (0x701504 0x00): SCR Line Heater #5 Circuit Failed Low —>

<!— 701505 (0x701505 0x00): SCR Line Heater #5 Circuit Failed Open —>

<!— 710202 (0x710202 0x00): CPC Message not Received or Stopped Arriving —>

<!— 710209 (0x710209 0x00): PT-CAN Heartbeat Missing —>

<!— 731609 (0x731609 0x00): MU_RESERVE_02_E5 —>

<!— 73160C (0x73160C 0x00): Soot Sensor heater Fault —>

<!— 740703 (0x740703 0x00): DEF Air Lock Valve Circuit Failed High —>

<!— 740704 (0x740704 0x00): DEF Air Lock Valve Circuit Failed Low —>

<!— 740705 (0x740705 0x00): DEF Air Lock Valve Circuit Failed Open —>

<!— 75020C (0x75020C 0x00): ACM Internal Error —>

<!— 75F0FF (0x75F0FF 0x00): DOC/DPF 2-Box system not detected —>

<!— 760202 (0x760202 0x00): Powerlatch of last driving cycle not completed —>

<!— 76020A (0x76020A 0x00): Loss of non-volatile data —>

<!— 76020C (0x76020C 0x00): E2P Hardware Error —>

<!— 76020D (0x76020D 0x00): MU_AUTH_E2P_DATA_LOSS inform TP PEE Team Kowol —>

<!— 76020E (0x76020E 0x00): E2P Emulation Hardware Error —>

<!— 76021F (0x76021F 0x00): Incorrect UDS security calibration —>

<!— 770E0E (0x770E0E 0x00): SCR OBD checks inhibited too long by the inhibit switch —>

<!— 770E1F (0x770E1F 0x00): Regen Inhibit Switch active when zone logic increments —>

<!— 77F0E9 (0x77F0E9 0x00): EDU CAN Message Not Received —>

<!— 78F0E0 (0x78F0E0 0x00): Calibratable Inhibit Test MUs with Changing FMI —>

<!— 79F0E1 (0x79F0E1 0x00): Calibratable Inhibit Test2 MUs with Changing FMI —>

<!— 7BF0FF (0x7BF0FF 0x00): EDU dosing unit defect —>

<!— 7CF0FF (0x7CF0FF 0x00): EDU supply unit Defect —>

<!— 7E1400 (0x7E1400 0x00): Regulatory Fault Ignored — Final Action (Speed Limit) —>

<!— 7E140F (0x7E140F 0x00): Regulatory Fault Ignored — Derate On —>

<!— 7E1410 (0x7E1410 0x00): Regulatory Fault Ignored — Final Action Pending —>

<!— 7F0E1F (0x7F0E1F 0x00): Parked Regen Failed — DOC Temp In Low Preventing Dosing —>

<!— 7F150D (0x7F150D 0x00): Fuel Mass Signal Not Available via CAN —>

<!— 80F0F1 (0x80F0F1 0x00): MU_SCR_ADS_FILT_DEF_SERV not in use —>

<!— 80F0F2 (0x80F0F2 0x00): MU_SCR_ADS_FILT_DEF_LT_EX not in use —>

<!— 810E1F (0x810E1F 0x00): Parked Regen Failed — DOC Temp Out, Not Reaching Target Temp —>

<!— 83F0E3 (0x83F0E3 0x00): High Side Digital Output Supply Voltage Circuit Failed High —>

<!— 83F0E4 (0x83F0E4 0x00): High Side Digital Output Supply Voltage Circuit Failed Low —>

<!— 840609 (0x840609 0x00): CAN3 Signal Missing —>

<!— 850609 (0x850609 0x00): CAN4 Signal Missing —>

<!— 85F0F1 (0x85F0F1 0x00): DEF filter change interval —>

<!— 85F0F2 (0x85F0F2 0x00): DEF filter overloaded —>

<!— 86F0E4 (0x86F0E4 0x00): MU_EDU_RESERV_03 —>

<!— 870E00 (0x870E00 0x00): Soot Level Very High —>

<!— 870E0F (0x870E0F 0x00): DPF Zone 3 Condition —>

<!— 870E10 (0x870E10 0x00): Soot Level High —>

<!— 870E1F (0x870E1F 0x00): DPF Zone 2 Condition —>

<!— 87F0E3 (0x87F0E3 0x00): MU_EDU_RESERV_04 —>

<!— 87F0E4 (0x87F0E4 0x00): MU_EDU_RESERV_02 —>

<!— 880E0F (0x880E0F 0x00): DPF Ash Clean Request —>

<!— 880E10 (0x880E10 0x00): DPF Ash Derate Request —>

<!— 88F0E7 (0x88F0E7 0x00): DEF system has been over pressurized —>

<!— 89F0FF (0x89F0FF 0x00): DEF flow quantity below normal —>

<!— 8CF0F1 (0x8CF0F1 0x00): Selective Catalyst Reduction (SCR) Inlet Temperature Too Low —>

<!— 8DF0E1 (0x8DF0E1 0x00): Soot Sensor Rationality Error —>

<!— 8DF0EE (0x8DF0EE 0x00): Soot Sensor Efficiency Error —>

<!— 8DF0F4 (0x8DF0F4 0x00): Soot Sensor Drift High —>

<!— 8DF0F5 (0x8DF0F5 0x00): Soot Sensor Drift Low —>

<!— 8DF0FF (0x8DF0FF 0x00): Soot sensor diagnosis request counter monitoring —>

<!— 8EF0EE (0x8EF0EE 0x00): MLIT Restart restriction —>

<!— 8FF0F0 (0x8FF0F0 0x00): Soot Sensor Heater Performance Error —>

<!— 900C02 (0x900C02 0x00): SCR Outlet NOx Sensor — Rationality Error —>

<!— 900C03 (0x900C03 0x00): SCR Inlet Nox Sensor Circuit Failed High —>

<!— 900C04 (0x900C04 0x00): SCR Inlet Nox Sensor Circuit Failed Low —>

<!— 900C07 (0x900C07 0x00): Nox raw sensor presence check —>

<!— 900C0B (0x900C0B 0x00): SCR Inlet NOx — Rationality Error —>

<!— 900C0D (0x900C0D 0x00): SCR Inlet Nox Sensor Signal Not Available —>

<!— 900C0E (0x900C0E 0x00): nox raw sensor does not support self diagnosis —>

<!— 900C0F (0x900C0F 0x00): NOx efficiency above desired target level, most likely nox raw sensor drifted —>

<!— 900C13 (0x900C13 0x00): nox raw E2P self check error detected —>

<!— 900C14 (0x900C14 0x00): Nox Raw sensor diagnosis oxygen pump capacity high —>

<!— 900C15 (0x900C15 0x00): Nox Raw sensor diagnosis oxygen pump capacity low —>

<!— 900C1F (0x900C1F 0x00): Nox Raw sensor diagnosis request counter monitoring —>

<!— 90F0EC (0x90F0EC 0x00): Soot Sensor Current Fail —>

<!— 910C03 (0x910C03 0x00): Selective Catalyst Reduction Inlet NOx Sensor Lambda 1 Circuit Failed High —>

<!— 910C05 (0x910C05 0x00): Selective Catalyst Reduction Inlet NOx Sensor Lambda 1 Circuit Failed Open —>

<!— 91F0EE (0x91F0EE 0x00): Soot Sensor Temperature Error —>

<!— 92F0EE (0x92F0EE 0x00): Soot Sensor Heater Fail —>

<!— 93F0EE (0x93F0EE 0x00): Soot Sensor Power Error —>

<!— 940403 (0x940403 0x00): Turbo Compressor Inlet Temperature Circuit Failed High —>

<!— 940404 (0x940404 0x00): Turbo Compressor Inlet Temperature Circuit Failed Low —>

<!— 95F0E3 (0x95F0E3 0x00): MU_ISP_DUMMY_04_SRH —>

<!— 96100E (0x96100E 0x00): Tier4 Inducement System has not been activated —>

<!— 96F0F1 (0x96F0F1 0x00): DEF Plausibility Value High —>

<!— 970C07 (0x970C07 0x00): NOx RAW Sensor not ready after dewpoint enable check —>

<!— 981303 (0x981303 0x00): High Side Digital Output 4 Circuit Failed High —>

<!— 981304 (0x981304 0x00): High Side Digital Output 4 Circuit Failed Low —>

<!— 98F0F2 (0x98F0F2 0x00): MU_RESERVE_02 —>

<!— 991303 (0x991303 0x00): High Side Digital Output 5 Circuit Failed High —>

<!— 991304 (0x991304 0x00): High Side Digital Output 5 Circuit Failed Low —>

<!— 99F0E0 (0x99F0E0 0x00): MLIT Case3 Inducement — Diesel-Exhaust-Fuel quality error —>

<!— 9A0C02 (0x9A0C02 0x00): SCR Outlet Nox Sensor — Drift —>

<!— 9A0C03 (0x9A0C03 0x00): SCR Outlet Nox Sensor Circuit Failed High —>

<!— 9A0C04 (0x9A0C04 0x00): SCR Outlet Nox Sensor Circuit Failed Low —>

<!— 9A0C07 (0x9A0C07 0x00): Nox out sensor presence check —>

<!— 9A0C0A (0x9A0C0A 0x00): Nox Out sensor signal erratic —>

<!— 9A0C0B (0x9A0C0B 0x00): SCR Outlet NOx — Rationality Error —>

<!— 9A0C0D (0x9A0C0D 0x00): SCR Outlet Nox Sensor Signal Not Available —>

<!— 9A0C0E (0x9A0C0E 0x00): MU_ISP_NOXO_CONV_RAT —>

<!— 9A0C12 (0x9A0C12 0x00): MU_RESERVE_03 —>

<!— 9A0C13 (0x9A0C13 0x00): nox out E2P self check error detected —>

<!— 9A0C14 (0x9A0C14 0x00): Nox Outlet Sensor Drift High —>

<!— 9A0C15 (0x9A0C15 0x00): Nox Outlet Sensor Drift Low —>

<!— 9A0C1F (0x9A0C1F 0x00): Nox Out sensor diagnosis request counter monitoring —>

<!— 9A1312 (0x9A1312 0x00): DOC efficiency Low —>

<!— 9AF0EE (0x9AF0EE 0x00): MU_FMM_TEST1 Fuelmap Not for Production —>

<!— 9B0C03 (0x9B0C03 0x00): Selective Catalyst Reduction Outlet NOx Sensor Lambda 1 Circuit Failed High —>

<!— 9B0C05 (0x9B0C05 0x00): Selective Catalyst Reduction Outlet NOx Sensor Lambda 1 Circuit Failed Open —>

<!— 9BF0EE (0x9BF0EE 0x00): MU_FMM_TEST2 Fuelmap Not for Production —>

<!— 9CF0EE (0x9CF0EE 0x00): Soot Sensor Protection Tube —>

<!— 9DF0EE (0x9DF0EE 0x00): DPF Filter Efficiency too Low —>

<!— 9E0003 (0x9E0003 0x00): MU_RESERVE_06 —>

<!— 9E0004 (0x9E0004 0x00): MU_RESERVE_05 —>

<!— 9E0007 (0x9E0007 0x00): ACM Power Down — Key Off Purge Cycle —>

<!— 9EF0E9 (0x9EF0E9 0x00): MU_ISP_RESERVE_2 —>

<!— 9EF0ED (0x9EF0ED 0x00): MU_ISP_RESERVE_3 —>

<!— 9EF0FF (0x9EF0FF 0x00): MU_ISP_RESERVE_1 —>

<!— 9FF0EE (0x9FF0EE 0x00): Uncooled DEF system, System no cool —>

<!— A0F0E3 (0xA0F0E3 0x00): Supply Voltage Difference Between ACM and Soot Sensor —>

<!— A0F0E4 (0xA0F0E4 0x00): MU_DPS_SPLY_ERR —>

<!— A1F0F0 (0xA1F0F0 0x00): Soot Sensor Temperature Rationality Failure — Above Normal —>

<!— A1F0F1 (0xA1F0F1 0x00): Soot Sensor Temperature Rationality Failure —>

<!— A20D03 (0xA20D03 0x00): DEF Purge Lamp Circuit Failed High —>

<!— A20D04 (0xA20D04 0x00): DEF Purge Lamp Circuit Failed Low —>

<!— A20D05 (0xA20D05 0x00): DEF Purge Lamp Circuit Failed Open —>

<!— A2F0EA (0xA2F0EA 0x00): Mixer Temperature Sensor — Rationality Error —>

<!— A3F0EE (0xA3F0EE 0x00): nox out sensor does not support self diagnosis —>

<!— A3F0F4 (0xA3F0F4 0x00): Nox Out sensor diagnosis oxygen pump capacity high —>

<!— A3F0F5 (0xA3F0F5 0x00): Nox Out sensor diagnosis oxygen pump capacity low —>

<!— A40C09 (0xA40C09 0x00): Exhaust Mass Signal Not Available via CAN —>

<!— A40C0F (0xA40C0F 0x00): Exhaust gas mass flow rate plausibility error —>

<!— A4F0F0 (0xA4F0F0 0x00): Soot sensor interal heater supply high error —>

<!— A4F0F2 (0xA4F0F2 0x00): Soot sensor interal heater supply low error —>

<!— A5F0E2 (0xA5F0E2 0x00): Soot Sensor printed circuit board Temperature rationality check. —>

<!— A5F0EF (0xA5F0EF 0x00): Soot Sensor printed circuit board temperature high —>

<!— A60C02 (0xA60C02 0x00): NOx OUT Sensor not ready after dewpoint enable check —>

<!— A60E1F (0xA60E1F 0x00): High Idle Regen Aborted — CPC Request —>

<!— A6F0E3 (0xA6F0E3 0x00): Soot Sensor printed circuit board Temperature 2 signal range high —>

<!— A6F0E4 (0xA6F0E4 0x00): Soot Sensor printed circuit board Temperature 2 signal range low —>

<!— A7F0E3 (0xA7F0E3 0x00): Soot Sensor heater short circuit to battery —>

<!— A7F0E4 (0xA7F0E4 0x00): Soot Sensor heater short circuit to ground —>

<!— A7F0E5 (0xA7F0E5 0x00): Soot Sensor heater open load —>

<!— A7F0EC (0xA7F0EC 0x00): Soot Sensor heater Printed Circuit Board circuit —>

<!— A80000 (0xA80000 0x00): Battery Voltage High —>

<!— A80001 (0xA80001 0x00): Battery Voltage Low —>

<!— A8F0E3 (0xA8F0E3 0x00): Soot Sensor Probe positive short circuit to battery diagnostic —>

<!— A8F0E4 (0xA8F0E4 0x00): Soot Sensor Probe positive short circuit to ground diagnostic —>

<!— A8F0EF (0xA8F0EF 0x00): Soot Sensor Probe positive signal range high diagnostic —>

<!— A9F0E2 (0xA9F0E2 0x00): Soot Sensor Temperature Rationality Signal Range Low —>

<!— A9F0F0 (0xA9F0F0 0x00): Soot Sensor temperature high —>

<!— A9F0F2 (0xA9F0F2 0x00): Soot Sensor temperature low —>

<!— AA0C00 (0xAA0C00 0x00): DOC inlet Temperature High —>

<!— AA0C02 (0xAA0C02 0x00): DOC Inlet Temperature Stuck (high box) —>

<!— AA0C03 (0xAA0C03 0x00): DOC Inlet Temperature Circuit Failed High —>

<!— AA0C04 (0xAA0C04 0x00): DOC Inlet Temperature Circuit Failed Low —>

<!— AA0C07 (0xAA0C07 0x00): DOC Inlet Temperature Missing or Bypassed —>

<!— AA0C08 (0xAA0C08 0x00): DOC Inlet Temperature — Signal Spike —>

<!— AA0C0A (0xAA0C0A 0x00): DOC Inlet Temperature Sensor Stuck —>

<!— AA0C0E (0xAA0C0E 0x00): DOC inlet Temperature sensor not plausible —>

<!— AA0C11 (0xAA0C11 0x00): Diesel Oxidation Catalyst (DOC) Inlet Temperature Out Of Range Low Preventing HC Dosing —>

<!— AA0C14 (0xAA0C14 0x00): DOC Temperature Drift — Inlet High or Outlet Low —>

<!— AA0C15 (0xAA0C15 0x00): DOC Inlet Temperature Sensor — Plausibility Error —>

<!— AA0C1F (0xAA0C1F 0x00): DOC Clean-up Fault —>

<!— AAF0E3 (0xAAF0E3 0x00): Soot Sensor supply line signal range high —>

<!— AAF0E4 (0xAAF0E4 0x00): Soot Sensor supply line signal range low —>

<!— AB0002 (0xAB0002 0x00): Ambient Air Temperature Not Plausible —>

<!— AB0003 (0xAB0003 0x00): Ambient Air Temperature Circuit Failed High —>

<!— AB0004 (0xAB0004 0x00): Ambient Air Temperature Circuit Failed Low —>

<!— AB0008 (0xAB0008 0x00): Ambient Air Temp Signal Spike —>

<!— AB000D (0xAB000D 0x00): Ambient Air Temperature Signal Not Available via CAN —>

<!— ABF0E3 (0xABF0E3 0x00): Selective Catalyst Reduction Inlet NOx Sensor Heater Circuit Failed High —>

<!— ABF0E5 (0xABF0E5 0x00): Selective Catalyst Reduction Inlet NOx Sensor Heater Circuit Failed Open —>

<!— ACF0E3 (0xACF0E3 0x00): Selective Catalyst Reduction Inlet NOx Sensor Control Circuit Failed High —>

<!— ACF0E5 (0xACF0E5 0x00): Selective Catalyst Reduction Inlet NOx Sensor Control Circuit Failed Open —>

<!— ADF0E3 (0xADF0E3 0x00): Selective Catalyst Reduction Outlet NOx Sensor Heater Circuit Failed High —>

<!— ADF0E5 (0xADF0E5 0x00): Selective Catalyst Reduction Outlet NOx Sensor Heater Circuit Failed Open —>

<!— AE0C00 (0xAE0C00 0x00): DPF Outlet Temperature Very High —>

<!— AE0C03 (0xAE0C03 0x00): DPF Outlet Temperature Circuit Failed High —>

<!— AE0C04 (0xAE0C04 0x00): DPF Outlet Temperature Circuit Failed Low —>

<!— AE0C07 (0xAE0C07 0x00): DPF Outlet Temperature Response Error —>

<!— AE0C08 (0xAE0C08 0x00): DPF Outlet Temperature — Signal Spike —>

<!— AE0C0A (0xAE0C0A 0x00): DPF Outlet Temperature Sensor Stuck —>

<!— AE0C0E (0xAE0C0E 0x00): Abnormal DPF Temperature Rise 2 —>

<!— AE0C0F (0xAE0C0F 0x00): DPF Outlet Temperature — High —>

<!— AE0C14 (0xAE0C14 0x00): DPF Outlet/SCR Inlet Temperature — Abnormal —>

<!— AE0C15 (0xAE0C15 0x00): DPF Outlet Temperature Sensor — Plausibility Error —>

<!— AE0C1F (0xAE0C1F 0x00): Abnormal DPF Temperature Rise 1 —>

<!— AEF0E3 (0xAEF0E3 0x00): Selective Catalyst Reduction Outlet NOx Sensor Control Circuit Failed High —>

<!— AEF0E5 (0xAEF0E5 0x00): Selective Catalyst Reduction Outlet NOx Sensor Control Circuit Failed Open —>

<!— AFF0E3 (0xAFF0E3 0x00): Selective Catalyst Reduction Inlet NOx Sensor Lambda 2 Circuit Failed High —>

<!— AFF0E5 (0xAFF0E5 0x00): Selective Catalyst Reduction Inlet NOx Sensor Lambda 2 Circuit Failed Open —>

<!— B0F0EE (0xB0F0EE 0x00): Selective Catalyst Reduction Outlet NOx Sensor Lambda 2 Circuit Failed Open —>

<!— B0F0FF (0xB0F0FF 0x00): Selective Catalyst Reduction Outlet NOx Sensor Lambda 2 Circuit Failed High —>

<!— B20C00 (0xB20C00 0x00): DOC Outlet Temperature Very High —>

<!— B20C03 (0xB20C03 0x00): DOC Outlet Temperature Circuit Failed High —>

<!— B20C04 (0xB20C04 0x00): DOC Outlet Temperature Circuit Failed Low —>

<!— B20C07 (0xB20C07 0x00): DOC Outlet Temperature Response Error —>

<!— B20C08 (0xB20C08 0x00): DOC Outlet Temperature — Signal Spike —>

<!— B20C0A (0xB20C0A 0x00): DOC Outlet Temperature Sensor Stuck —>

<!— B20C0E (0xB20C0E 0x00): Abnormal DOC Temperature Rise 2 —>

<!— B20C0F (0xB20C0F 0x00): DOC Outlet Temperature — High —>

<!— B20C14 (0xB20C14 0x00): DOC Temperature Drift — Inlet Low or Outlet High —>

<!— B20C15 (0xB20C15 0x00): DOC Inboard Outlet Temperature Sensor — Plausibility Error —>

<!— B20C1F (0xB20C1F 0x00): Abnormal DOC Temperature Rise 1 —>

<!— B2140E (0xB2140E 0x00): SCR Abnormal Temperature Rise —>

<!— B30C00 (0xB30C00 0x00): DPF Pressure Out of Range Very High —>

<!— B30C01 (0xB30C01 0x00): DPF Pressure Out of Range Low —>

<!— B30C0E (0xB30C0E 0x00): ATS pressure loss —>

<!— B30C0F (0xB30C0F 0x00): Pressure drop across DOC/DPF too high —>

<!— B30C10 (0xB30C10 0x00): DPF Pressure — Out of Range High —>

<!— B30C14 (0xB30C14 0x00): DOC Inlet Pressure Sensor — Not Plausible —>

<!— B30C15 (0xB30C15 0x00): DOC Inlet / Outlet Pressure Not Plausible —>

<!— B30C1F (0xB30C1F 0x00): Pressure drop across the filter too high — lowest level —>

<!— B50D03 (0xB50D03 0x00): ACM Sensor Supply 1 Short to Battery —>

<!— B50D04 (0xB50D04 0x00): ACM Sensor Supply 1 Short to Ground —>

<!— B5F0EA (0xB5F0EA 0x00): SCR Outlet Nox Sensor — Drift Low —>

<!— B60D03 (0xB60D03 0x00): ACM Sensor Supply 2 Short to Battery —>

<!— B60D04 (0xB60D04 0x00): ACM Sensor Supply 2 Short to Ground —>

<!— B61401 (0xB61401 0x00): AMOX catalyst is aged —>

<!— B81207 (0xB81207 0x00): SCR Catalyst — Age :Limit —>

<!— B8120E (0xB8120E 0x00): SCR Catalyst Aged Level 1 —>

<!— B8121F (0xB8121F 0x00): SCR Catalyst Aged Level 2 —>

<!— BA120E (0xBA120E 0x00): Detect the presence of the SCR —>

<!— BA121F (0xBA121F 0x00): SCR catalyst presence detection —>

<!— BB0D13 (0xBB0D13 0x00): Reductant Quality Sensor DEF Temperature Error —>

<!— BB121F (0xBB121F 0x00): DPF Outlet Temperature Response — Too fast —>

<!— BC0D01 (0xBC0D01 0x00): DEF Quality Sensor Percent Low —>

<!— BC0D04 (0xBC0D04 0x00): Reductant Quality Sensor Circuit Low —>

<!— BC0D07 (0xBC0D07 0x00): Diesel Exhaust Fluid Quality Concentration Not Responding Or Out Of Adjustment —>

<!— BC0D09 (0xBC0D09 0x00): Diesel Exhaust Fluid Quality Sensor Signal Not Available —>

<!— BC0D0A (0xBC0D0A 0x00): DEF quality sensor value stuck in range monitor —>

<!— BC0D0D (0xBC0D0D 0x00): DEF Quality Sensor CAN Signal Missing —>

<!— BC0D10 (0xBC0D10 0x00): DEF concentration too high —>

<!— BC0D12 (0xBC0D12 0x00): DEF concentration sensor rationality low —>

<!— BC0D13 (0xBC0D13 0x00): Reductant Quality Sensor Circuit Range-Performance —>

<!— BC0D14 (0xBC0D14 0x00): Diesel Exhaust Fluid Quality Concentration Data Drifted High —>

<!— BC0D15 (0xBC0D15 0x00): Diesel Exhaust Fluid Quality Concentration Data Drifted Low —>

<!— BC121F (0xBC121F 0x00): DOC Outlet Temperature Response — Too Fast —>

<!— BCF0EB (0xBCF0EB 0x00): NOx sensor rat check failed/uncompleted too often —>

<!— BD0D01 (0xBD0D01 0x00): DEF Tank Level — Zone 4 —>

<!— BD0D09 (0xBD0D09 0x00): DEF Tank Level Signal Not Available via CAN —>

<!— BD0D0D (0xBD0D0D 0x00): DEF Tank CAN Signal Missing —>

<!— BD0D0E (0xBD0D0E 0x00): DEF Tank Level — Zone 2 —>

<!— BD0D11 (0xBD0D11 0x00): DEF tank level check — Lim1 reserve —>

<!— BD0D12 (0xBD0D12 0x00): DEF Tank Level — Zone 3 —>

<!— BD0D13 (0xBD0D13 0x00): DEF Tank Signal Erratic via CAN —>

<!— BD0D1F (0xBD0D1F 0x00): MU_TRC_L_DEF_TANK_LIM_5 —>

<!— BE0009 (0xBE0009 0x00): Engine Speed Signal Not Available via CAN —>

<!— C10D1F (0xC10D1F 0x00): Diesel Exhaust Fluid Quality Sensor Detects Diesel Fuel —>

<!— C11503 (0xC11503 0x00): Soot Sensor printed circuit board Temperature 1 signal range high —>

<!— C11504 (0xC11504 0x00): Soot Sensor printed circuit board Temperature 1 signal range low —>

<!— C1150C (0xC1150C 0x00): MU_RESERVE_01_E5 —>

<!— C30D08 (0xC30D08 0x00): Regen Frequency Error —>

<!— CF0409 (0xCF0409 0x00): MCM CAN1 Signal Missing —>

<!— D00C00 (0xD00C00 0x00): DPF Outlet Temperature High (Bank 2) —>

<!— D00C0E (0xD00C0E 0x00): Abnormal DPF Temperature Rise second leg — uncontrolled regeneration —>

<!— D30409 (0xD30409 0x00): MCM CAN2 Signal Missing —>

<!— D40C00 (0xD40C00 0x00): DOC Outlet Temperature High (Bank 2) —>

<!— D40C03 (0xD40C03 0x00): DOC Outboard Outlet Temperature Circuit Failed High —>

<!— D40C04 (0xD40C04 0x00): DOC Outboard Outlet Temperature Circuit Failed Low —>

<!— D40C08 (0xD40C08 0x00): DOC Outboard Outlet Temperature — Signal Spike —>

<!— D40C0A (0xD40C0A 0x00): DOC Outboard Outlet Temperature Sensor Stuck —>

<!— D40C0E (0xD40C0E 0x00): Abnormal Temperature reaction on DOC-B —>

<!— D40C0F (0xD40C0F 0x00): Preliminary over temperature for the DOC —>

<!— D40C15 (0xD40C15 0x00): DPF Outlet Temperature Sensor — Not Plausible —>

<!— D70B00 (0xD70B00 0x00): SCR Temperature of Tank is Too High —>

<!— D70B02 (0xD70B02 0x00): DEF Tank Temperature Drift in Range —>

<!— D70B03 (0xD70B03 0x00): DEF Tank Temperature Sensor Circuit Failed High —>

<!— D70B04 (0xD70B04 0x00): DEF Tank Temperature Sensor Circuit Failed Low —>

<!— D70B09 (0xD70B09 0x00): DEF Tank Temperature Signal Not Available via CAN —>

<!— D70B0A (0xD70B0A 0x00): DEF Tank Temperature Sensor Circuit rationality check —>

<!— D70B13 (0xD70B13 0x00): DEF Tank Temperature Error (CAN) —>

<!— E10601 (0xE10601 0x00): DEF Tank Level 0 — Empty (Speed Limited) —>

<!— E10602 (0xE10602 0x00): DEF Tank Level Sensor Rationality —>

<!— E10603 (0xE10603 0x00): DEF Tank Level Sensor Circuit Failed High —>

<!— E10604 (0xE10604 0x00): DEF Tank Level Sensor Circuit Failed Low —>

<!— E10609 (0xE10609 0x00): DEF tank level signal not available —>

<!— E1060D (0xE1060D 0x00): Diesel Exhaust Fluid Tank Level Out Of Calibration —>

<!— E1060E (0xE1060E 0x00): DEF Tank Level 2 — Very Low —>

<!— E10611 (0xE10611 0x00): DEF Level Low —>

<!— E10612 (0xE10612 0x00): DEF Tank Level 1 — Empty —>

<!— E1061F (0xE1061F 0x00): DEF Tank Level 3 — Low —>

<!— E40D00 (0xE40D00 0x00): Regen Temperature — Out of Range High —>

<!— E40D01 (0xE40D01 0x00): Regen Temperature — Out of Range Low —>

<!— E40D12 (0xE40D12 0x00): DOC Outlet Temp Low (Low Temp Regen) —>

<!— EA0B00 (0xEA0B00 0x00): Engine Air Flow Out of Range Low —>

<!— EA0B01 (0xEA0B01 0x00): Active Regen Temp Out of Range Low —>

<!— EB0B1F (0xEB0B1F 0x00): Determine the aging effect on SCR —>

<!— EB1010 (0xEB1010 0x00): DEF Dosing Quantity High —>

<!— EB1012 (0xEB1012 0x00): DEF Dosing Quantity Low —>

<!— EC101F (0xEC101F 0x00): DOC inlet temperature out of range low preventing hc dosing —>

<!— ED000D (0xED000D 0x00): ACM ECU has detected an exchange of MCM or ACM ECU —>

<!— EE1002 (0xEE1002 0x00): DEF Pressure Sensor Drift in Range —>

<!— EE1003 (0xEE1003 0x00): DEF Pressure Sensor Circuit Failed High —>

<!— EE1004 (0xEE1004 0x00): DEF Pressure Sensor Circuit Failed Low —>

<!— EE1005 (0xEE1005 0x00): DEF Pressure Sensor not Plausible —>

<!— EE1007 (0xEE1007 0x00): DEF Pressure Low —>

<!— EE1008 (0xEE1008 0x00): DEF Pressure Signal Spike —>

<!— EE100A (0xEE100A 0x00): DEF Accumulator Failure —>

<!— EE1011 (0xEE1011 0x00): DEF Purge Pressure High —>

<!— EF1001 (0xEF1001 0x00): DEF Air Pressure Not Detected (from vehicle supply) —>

<!— EF1002 (0xEF1002 0x00): DEF Air Pressure Sensor Drift —>

<!— EF1003 (0xEF1003 0x00): DEF Air Pressure Sensor Circuit Failed High —>

<!— EF1004 (0xEF1004 0x00): DEF Air Pressure Sensor Circuit Failed Low —>

<!— EF1005 (0xEF1005 0x00): DEF Air Pressure Sensor not Plausible —>

<!— EF1007 (0xEF1007 0x00): DEF Air Pressure Air Low —>

<!— EF1008 (0xEF1008 0x00): DEF Air Pressure Signal Spike —>

<!— EF100E (0xEF100E 0x00): DEF Air Pressure High —>

<!— EF101F (0xEF101F 0x00): DEF — Information Only —>

<!— F00B02 (0xF00B02 0x00): SCR Inlet Nox Sensor — Error —>

<!— F01003 (0xF01003 0x00): DEF Air Valve Circuit Failed High —>

<!— F01004 (0xF01004 0x00): DEF Air Valve Circuit Failed Low —>

<!— F01005 (0xF01005 0x00): DEF Air Valve Circuit Failed Open —>

<!— F10B02 (0xF10B02 0x00): SCR Outlet Nox Sensor — Error —>

<!— F11000 (0xF11000 0x00): Diesel Exhaust Fluid Temperature Data Valid But Above Normal Operational Range —>

<!— F11002 (0xF11002 0x00): DEF Dosing Unit Temperature Drift in Range —>

<!— F11003 (0xF11003 0x00): DEF Temperature Sensor Circuit Failed High —>

<!— F11004 (0xF11004 0x00): DEF Temperature Sensor Circuit Failed Low —>

<!— F20E00 (0xF20E00 0x00): Long term DEF consumption too high —>

<!— F20E01 (0xF20E01 0x00): Long term DEF consumption too low —>

<!— F31007 (0xF31007 0x00): DPF Feedback Regen Control Error —>

<!— F40E00 (0xF40E00 0x00): Short term DEF consumption too high —>

<!— F40E01 (0xF40E01 0x00): Short term DEF consumption too low —>

<!— F40E0F (0xF40E0F 0x00): Average reductant consumption too high —>

<!— F40E11 (0xF40E11 0x00): Average reductant consumption too low —>

<!— F80B07 (0xF80B07 0x00): High Idle Regeneration Not Complete —>

<!— F80B0D (0xF80B0D 0x00): DPF System Parametrization Failure —>

<!— F80B0E (0xF80B0E 0x00): Pressure drop across DPF too low —>

<!— FE0F1F (0xFE0F1F 0x00): DEF Dilution detected —>

<!— 08110B (0x08110B 0x00): MU_ISP_T_SCR_IN_GRAD —>

<!— 08110E (0x08110E 0x00): SCR inlet temperature not warm up —>

<!— 08111F (0x08111F 0x00): SCR temperature not warm up —>

<!— 0B1102 (0x0B1102 0x00): Selective Catalyst Reduction Outlet Temperature — Not Plausible —>

<!— 0B110B (0x0B110B 0x00): MU_ISP_T_SCR_OUT_GRAD —>

<!— 0B1110 (0x0B1110 0x00): MU_SCR_MON_T_GRAD_SCR_SRH —>

<!— 0C1110 (0x0C1110 0x00): SCR Catalyst Efficiency too high —>

<!— 0C1111 (0x0C1111 0x00): SCR NOx Conversion Efficiency Low detection by moving average —>

<!— 161109 (0x161109 0x00): DEF PSV loop error —>

<!— 16110B (0x16110B 0x00): DEF PNV SRL loop error —>

<!— 16110E (0x16110E 0x00): DEF PNV SRH loop error —>

<!— 190E0C (0x190E0C 0x00): Pressure DPF inlet not plausible —>

<!— 190E1F (0x190E1F 0x00): engine-off DOC inlet pressure drift high —>

<!— 1A0E0C (0x1A0E0C 0x00): Pressure DPF outlet not plausible —>

<!— 200D0B (0x200D0B 0x00): Diesel-Exhaust-Fuel quality sensor concentration read-out not possible —>

<!— 2FF0E3 (0x2FF0E3 0x00): DPF (DPF_1 — pin 120/91) Signal Range High —>

<!— 2FF0E4 (0x2FF0E4 0x00): DPF (DPF_1 — pin 120/91) Signal Range Low —>

<!— 30F0E3 (0x30F0E3 0x00): DPF (DPF_2 — pin 120/95) Signal Range High —>

<!— 30F0E4 (0x30F0E4 0x00): DPF (DPF_2 — pin 120/95) Signal Range Low —>

<!— 31F0E3 (0x31F0E3 0x00): DPF (SCR_1 — pin 120/113) Signal Range High —>

<!— 31F0E4 (0x31F0E4 0x00): DPF (SCR_1 — pin 120/113) Signal Range Low —>

<!— 32F0E3 (0x32F0E3 0x00): DPF (SCR_2 — pin 120/115) Signal Range High —>

<!— 32F0E4 (0x32F0E4 0x00): DPF (SCR_2 — pin 120/115) Signal Range Low —>

<!— 33F0E3 (0x33F0E3 0x00): DPF (SCR_3 — pin 120/119) Signal Range High —>

<!— 33F0E4 (0x33F0E4 0x00): DPF (SCR_3 — pin 120/119) Signal Range Low —>

<!— 38F0E3 (0x38F0E3 0x00): DPF (DPF_1 — pin 120/118) Signal Range Low —>

<!— 3B150B (0x3B150B 0x00): DEF Pump block loop error —>

<!— 3D1103 (0x3D1103 0x00): DPF (SCR_1 — pin 120/80) Signal Range High —>

<!— 3D1104 (0x3D1104 0x00): DPF (SCR_1 — pin 120/80) Signal Range Low —>

<!— 600F0E (0x600F0E 0x00): MU_DPF_MON_EST_ERROR —>

<!— 770E0B (0x770E0B 0x00): Driver information: SCR OBD checks inhibited too long by the inhibit switch —>

<!— 900C0A (0x900C0A 0x00): Nox Raw sensor signal erratic —>

<!— 900C10 (0x900C10 0x00): Engine Out NOx Sensor drifted low —>

<!— 900C12 (0x900C12 0x00): NOx raw sensor deviation too high — detection by LARMF —>

<!— 910C02 (0x910C02 0x00): Engine out lambda sensor drift low —>

<!— 940408 (0x940408 0x00): Reserved_MU_ISP_T_COMP_IN_GRAD —>

<!— 9A0C09 (0x9A0C09 0x00): MU_ISP_NOX_OUT_NOISE _SPK —>

<!— 9A130E (0x9A130E 0x00): Detected clogged DOC —>

<!— 9B0C02 (0x9B0C02 0x00): Tail pipe lambda sensor drift low —>

<!— A40C0E (0xA40C0E 0x00): Modelled Exhaust Mass Signal Not Available via CAN —>

<!— AA0C0B (0xAA0C0B 0x00): MU_ISP_T_DOC_IN_GRAD —>

<!— AA0C12 (0xAA0C12 0x00): Insufficient DOC Inlet Light of Temperature —>

<!— AE0C02 (0xAE0C02 0x00): Diesel Particulate Filter Outlet Temperature Signal — Not Plausible —>

<!— AE0C0B (0xAE0C0B 0x00): MU_ISP_T_DPF_OUT_GRAD —>

<!— B1F0EE (0xB1F0EE 0x00): MU_FMM_AS_ET_TEST1, Fuelmap Not for Production —>

<!— B20C02 (0xB20C02 0x00): Diesel Oxidation Catalyst temperature sensor — plausibility error —>

<!— B20C0B (0xB20C0B 0x00): MU_ISP_T_DOC_OUT_GRAD —>

<!— B2F0EE (0xB2F0EE 0x00): MU_FMM_AS_ET_TEST2, Fuelmap Not for Production —>

<!— B30C03 (0xB30C03 0x00): DPF Delta Pressure Circuit Failed High —>

<!— B30C04 (0xB30C04 0x00): DPF Delta Pressure Circuit Failed Low —>

<!— B3F0F0 (0xB3F0F0 0x00): SCR closed loop control at maximum limit (Multiples Sources) —>

<!— B3F0F2 (0xB3F0F2 0x00): Unspecific fault — detection by LARMF —>

<!— B4140E (0xB4140E 0x00): DOC feed gas error —>

<!— B41411 (0xB41411 0x00): DOC feed gas low —>

<!— B41412 (0xB41412 0x00): LO NO2 feedgas by LARMF —>

<!— B4141F (0xB4141F 0x00): NO2 feed gas signal range low —>

<!— B4F0EE (0xB4F0EE 0x00): SCR closed loop control at maximum limit (Timeout) —>

<!— B4F0F0 (0xB4F0F0 0x00): SCR closed loop control at maximum limit —>

<!— B4F0F2 (0xB4F0F2 0x00): Mean LARMF value below expected level —>

<!— B6F0EE (0xB6F0EE 0x00): MU_DPF_DIA_DOC_FG _LOW —>

<!— B70D03 (0xB70D03 0x00): 3V Sensor Supply Bank 1 Circuit Failed High —>

<!— B70D04 (0xB70D04 0x00): 3V Sensor Supply Bank 1 Circuit Failed Low —>

<!— B7F0EE (0xB7F0EE 0x00): Initial communication with engine control module disturbed —>

<!— B80D03 (0xB80D03 0x00): 3V Sensor Supply Bank 2 Circuit Failed High —>

<!— B80D04 (0xB80D04 0x00): 3V Sensor Supply Bank 2 Circuit Failed Low —>

<!— B81202 (0xB81202 0x00): Rationality check for t_scr —>

<!— B8F0EE (0xB8F0EE 0x00): Freeze Frame key information synchronisation failed —>

<!— B9F0ED (0xB9F0ED 0x00): Measurement interface active in Aftertreatment Controle Module —>

<!— B9F0EE (0xB9F0EE 0x00): MU_XCP_ CCP_ ACTIVE —>

<!— B9F0FF (0xB9F0FF 0x00): MU_XCP_CCP_ ACTIVE —>

<!— BAF0E0 (0xBAF0E0 0x00): Aftertreatment Temperature not plausible —>

<!— BB0D03 (0xBB0D03 0x00): MU_UQC_T_SENS_OL —>

<!— BB0D04 (0xBB0D04 0x00): MU_UQC_T_SENS_SC —>

<!— BBF0EE (0xBBF0EE 0x00): Diesel-Exhaust-Fuel dosing amount out of desired operation parameters —>

<!— BC0D03 (0xBC0D03 0x00): Diesel-Exhaust-Fuel quality sensor open load —>

<!— BC0D0B (0xBC0D0B 0x00): Diesel-Exhaust-Fuel quality sensor internal error —>

<!— BC0D0E (0xBC0D0E 0x00): Diesel-Exhaust-Fuel concentration invalid —>

<!— BD0D03 (0xBD0D03 0x00): MU_UQC_L_SENS_OL —>

<!— BD0D0A (0xBD0D0A 0x00): MU_ISP_CAN_L_UREA_TANK_NVLD —>

<!— BD0D0B (0xBD0D0B 0x00): MU_UQC_L_SENS_ERR —>

<!— BDF0E2 (0xBDF0E2 0x00): Diesel Oxidation Catalyst Inlet Temperature Signal not plausible —>

<!— BEF0EE (0xBEF0EE 0x00): Backstop MU for nox efficiency monitor —>

<!— BEF0FF (0xBEF0FF 0x00): NOx efficiency by NOxTP Sensor above expected level fault —>

<!— BFF0E2 (0xBFF0E2 0x00): DEF tank temperature — cool down —>

<!— BFF0EA (0xBFF0EA 0x00): DEF tank temperature — warm up —>

<!— C7140E (0xC7140E 0x00): Soot sensor regeneration not possible —>

<!— CDF0EE (0xCDF0EE 0x00): MU_NOX_MON_REG_CNT_SRH —>

<!— D1160E (0xD1160E 0x00): DEF Quality Low —>

<!— D1161F (0xD1161F 0x00): Diesel-Exhaust-Fuel dilution detected by LARMF —>

<!— D40C0B (0xD40C0B 0x00): MU_ISP_T_DOCB_OUT_GRAD —>

<!— D70B08 (0xD70B08 0x00): MU_ISP_T_UREA_TANK_GRAD —>

<!— E40D11 (0xE40D11 0x00): Diesel Oxidation Catalyst (DOC) Insufficient HC Conversion —>

<!— EB100F (0xEB100F 0x00): DEF Dosing Quantity Low system detection —>

<!— EB1011 (0xEB1011 0x00): Diesel-Exhaust-Fuel dosing amount limited — detection by LARMF —>

<!— EE1014 (0xEE1014 0x00): DEF pressure drift high —>

<!— EE1015 (0xEE1015 0x00): DEF pressure drift low —>

<!— F11008 (0xF11008 0x00): Reserved_MU_ISP_T_UREA_GRAD —>

<!— 83F0E4 (0x83F0E4 0x00): High Side Digital Output UV_DOS Circuit Failed Low —>

<!— 230D0C (0x230D0C 0x00): No THC heating valve present, but tank heating requested —>

<!— 2FF0EB (0x2FF0EB 0x00): DOC out temperature sensor: signal range high or low —>

<!— 30F0EB (0x30F0EB 0x00): DPF out temperature sensor: signal range high or low —>

<!— 31F0EE (0x31F0EE 0x00): ADC check —>

<!— 32F0EB (0x32F0EB 0x00): ACM functional safety disabled through reprogramming —>

<!— 32F0EE (0x32F0EE 0x00): Reserved_MU_FS_DIA_DSBL_REPROG —>

<!— 32F0FF (0x32F0FF 0x00): Black channel communication interrupted —>

<!— 37F0EB (0x37F0EB 0x00): Sensor supply voltage: signal range high or low —>

<!— 38F0E0 (0x38F0E0 0x00): MU_ECOP_IAPSOVERTEMP —>

<!— 38F0E8 (0x38F0E8 0x00): MU_ECOP_IAPSGRDMES —>

<!— 39F0E0 (0x39F0E0 0x00): ATS temperature too high: HC dosing disabled —>

<!— 511614 (0x511614 0x00): Nox Out sensor self-diagnosis Nox drifted high —>

<!— 511615 (0x511615 0x00): Nox Out sensor self-diagnosis Nox drifted low —>

<!— 521614 (0x521614 0x00): Nox Raw sensor self-diagnosis Nox drifted high —>

<!— 521615 (0x521615 0x00): Nox Raw sensor self-diagnosis Nox drifted low —>

<!— 62F0E0 (0x62F0E0 0x00): MU_ECOP_DTSOVERTEMP —>

<!— 69F0ED (0x69F0ED 0x00): Rescue vehicle mode different in variant coding and inducement usage —>

<!— 900C08 (0x900C08 0x00): Nox Raw sensor operation not stable —>

<!— 9A0C08 (0x9A0C08 0x00): Nox Out sensor operation not stable —>

<!— B6F0EE (0xB6F0EE 0x00): MU_DPF_DIA_DOC_FG_LOW —>

<!— B90D03 (0xB90D03 0x00): Nox Raw sensor supply voltage too high —>

<!— B90D04 (0xB90D04 0x00): Nox Raw sensor supply voltage too low —>

<!— BA0D03 (0xBA0D03 0x00): Nox Out sensor supply voltage too high —>

<!— BA0D04 (0xBA0D04 0x00): Nox Out sensor supply voltage too low —>

<!— BFF0E7 (0xBFF0E7 0x00): Exhaust heat recovery flap stuck open —>

<!— BFF0E9 (0xBFF0E9 0x00): Lost signal ‘exhaust heating system requested’ from MUX —>

<!— BFF0EE (0xBFF0EE 0x00): Exhaust heat recovery flap stuck closed —>

<!— BFF0F3 (0xBFF0F3 0x00): Lost signal ‘exhaust heating system released’ from MCM —>

<!— C0F0E3 (0xC0F0E3 0x00): MU_OFD_EXH_VALVE_SC_UBATT —>

<!— C0F0E4 (0xC0F0E4 0x00): MU_OFD_EXH_VALVE_SC_GND —>

<!— C0F0E5 (0xC0F0E5 0x00): MU_OFD_EXH_VALVE_OL —>

<!— C1F0ED (0xC1F0ED 0x00): Current CVN deviates from stored reference —>

<!— C2F0E9 (0xC2F0E9 0x00): MU_ISP_SENT1_TIMEOUT —>

<!— C2F0EC (0xC2F0EC 0x00): MU_ISP_SENT1_SENS_ERR —>

<!— C2F0ED (0xC2F0ED 0x00): MU_ISP_SENT1_FC_CRC_ERR —>

<!— C2F0EE (0xC2F0EE 0x00): MU_ISP_SENT1_SER_ERR —>

<!— C2F0F3 (0xC2F0F3 0x00): MU_ISP_SENT1_P_SIG_ERR —>

<!— C3F0F3 (0xC3F0F3 0x00): MU_ISP_SENT1_DP_SIG_ERR —>

<!— C4F0ED (0xC4F0ED 0x00): MU_ISP_SENT1_SER_CRC_ERR —>

<!— C4F0F3 (0xC4F0F3 0x00): MU_ISP_SENT1_T_SIG_ERR —>

<!— C5F0EB (0xC5F0EB 0x00): MU_MON_3 —>

<!— C5F0EE (0xC5F0EE 0x00): MU_MON_3_VD —>

<!— C5F0FF (0xC5F0FF 0x00): MU_MON_3_SW —>

<!— C6F0EB (0xC6F0EB 0x00): MU_MON_3_TMP —>

<!— C6F0EE (0xC6F0EE 0x00): MU_MON_3_COD_PROT —>

<!— C6F0FF (0xC6F0FF 0x00): MU_MON_3_DATA_PROT_0 —>

<!— C7F0EB (0xC7F0EB 0x00): MU_MON_3_DATA_PROT_1 —>

<!— C8F0ED (0xC8F0ED 0x00): MU_ECOP_ATIC153 —>

<!— C9F0ED (0xC9F0ED 0x00): MU_ECOP_ATIC235 —>

<!— CAF0ED (0xCAF0ED 0x00): MU_ECOP_LM95071 —>

<!— CBF0E9 (0xCBF0E9 0x00): MU_ECOP_NCV7520_2 —>

<!— CBF0ED (0xCBF0ED 0x00): MU_ECOP_NCV7520 —>

<!— CCF0EE (0xCCF0EE 0x00): Fault tolerance time (FTT) expired —>

<!— D70B0E (0xD70B0E 0x00): DEF Tank Temperature Sensor Circuit Range/Performance —>

<!— 07F0E1 (0x07F0E1 0x00): MU_RESERVE_04 —>

<!— 08F0F1 (0x08F0F1 0x00): MU_EDU_RESERV_01 —>

<!— 171510 (0x171510 0x00): MU_DPF_HC_QUANT_DEF_OP —>

<!— 6BF0E9 (0x6BF0E9 0x00): MU_ISP_HEARTBEAT_CAN4 —>

<!— 6D1603 (0x6D1603 0x00): MU_DPS_UBAT —>

<!— 6D160F (0x6D160F 0x00): MU_DPS_IDE_NEG —>

<!— 6D1611 (0x6D1611 0x00): MU_DPS_IDE_POS —>

<!— 6D1613 (0x6D1613 0x00): MU_DPS_SNA —>

<!— 73160F (0x73160F 0x00): MU_DPS_HTR_ON —>

<!— 731611 (0x731611 0x00): MU_DPS_HTR_OFF —>

<!— 7EF0FF (0x7EF0FF 0x00): DOC Clean-up Fault —>

<!— 96F0EE (0x96F0EE 0x00): MU reserve —>

<!— 9E0003 (0x9E0003 0x00): MU_OFD_HSW_KL15_SC_UBATT_OL —>

<!— 9E0004 (0x9E0004 0x00): MU_OFD_HSW_KL15_SC_GND —>

<!— A0F0E4 (0xA0F0E4 0x00): MU_DPS_DIA_SPLY_L_ERR —>

<!— A1F0EF (0xA1F0EF 0x00): MU_DPS_T_MEA_IV_RAT —>

<!— A1F0F3 (0xA1F0F3 0x00): MU_DPS_T_MEA —>

<!— C1150C (0xC1150C 0x00): MU_DPS_T_SENS —>

<!— C1150E (0xC1150E 0x00): MU_DPS_TEMP —>

<!— D40C0E (0xD40C0E 0x00): MU_DPF_Q_DOT_DOCB_ERR —>

<!— 00F0EE (0x00F0EE 0x00): EGR Feedback on Lambda to low —>

<!— 00F0EE (0x00F0EE 0x00): EGR Feedback on Lambda too Low —>

<!— 00F0EE (0x00F0EE 0x00): FSG: EGR Feedback on Lambda to low —>

<!— 00F0EE (0x00F0EE 0x00): MU_EGR_OBD_1 —>

<!— 00F0F0 (0x00F0F0 0x00): EGR Feedback on Lambda too High —>

<!— 00F0F2 (0x00F0F2 0x00): EGR Feedback on Lambda too Low —>

<!— 01F0EE (0x01F0EE 0x00): EGR Feedback on Lambda to high —>

<!— 01F0EE (0x01F0EE 0x00): EGR Feedback on Lambda too High —>

<!— 01F0EE (0x01F0EE 0x00): FSG: EGR Feedback on Lambda to high —>

<!— 01F0EE (0x01F0EE 0x00): MU_EGR_OBD_2 —>

<!— 01F0F0 (0x01F0F0 0x00): EGR Feedback on Lambda too High —>

<!— 02F0EE (0x02F0EE 0x00): MU_EGR_OBD_3 —>

<!— 03F0EE (0x03F0EE 0x00): MU_EGR_OBD_4 —>

<!— 040E03 (0x040E03 0x00): Ether Start, Shorted to Ground —>

<!— 040E04 (0x040E04 0x00): Ether Start, Shorted to Battery —>

<!— 040E05 (0x040E05 0x00): Ether Start, Open Load —>

<!— 04F0EE (0x04F0EE 0x00): MU_EGR_OBD_5 —>

<!— 051403 (0x051403 0x00): MU_ISP_ULIN_SRH —>

<!— 051404 (0x051404 0x00): MU_ISP_ULIN_SRL —>

<!— 05F0EE (0x05F0EE 0x00): MU_OBD_PROTO_EV_1 —>

<!— 06F0EE (0x06F0EE 0x00): MU_OBD_PROTO_EV_2 —>

<!— 07F0EE (0x07F0EE 0x00): MU_OBD_PROTO_EV_3 —>

<!— 080201 (0x080201 0x00): MU_EBM_BRAKE_MALFUNCTION —>

<!— 080212 (0x080212 0x00): MU_EBM_RED_BRAKE_POWER —>

<!— 08F0EE (0x08F0EE 0x00): MU_OBD_PROTO_EV_4 —>

<!— 09F0EE (0x09F0EE 0x00): MU_OBD_PROTO_EV_5 —>

<!— 0B020D (0x0B020D 0x00): J1939 Transmission Current Gear Signal is missing —>

<!— 0B020D (0x0B020D 0x00): J1939 Transmission Current Gear Signal is Missing —>

<!— 0B0213 (0x0B0213 0x00): J1939 Transmission Current Gear Signal is erratic —>

<!— 0B0213 (0x0B0213 0x00): J1939 Transmission Current Gear Signal is Erratic —>

<!— 0BF0E3 (0x0BF0E3 0x00): FSG: H Bridge 1 EGR Valve Circiut Shorted to Battery —>

<!— 0BF0E3 (0x0BF0E3 0x00): H Bridge 1 EGR Valve Circiut Shorted to Battery —>

<!— 0BF0E3 (0x0BF0E3 0x00): H Bridge 2 EGR Valve Circiut Shorted to Battery —>

<!— 0BF0E4 (0x0BF0E4 0x00): FSG: H Bridge 2 EGR Valve Circuit Shorted to Ground —>

<!— 0BF0E4 (0x0BF0E4 0x00): H Bridge 2 EGR Valve Circuit Shorted to Ground —>

<!— 0BF0E5 (0x0BF0E5 0x00): FSG: H Bridge 1 EGR Valve Short Circuit/Over Current —>

<!— 0BF0E5 (0x0BF0E5 0x00): H Bridge 1 EGR Valve Short Circuit/Over Current —>

<!— 0BF0E5 (0x0BF0E5 0x00): H Bridge 2 EGR Valve Short Circuit/ Over Current —>

<!— 0BF0EE (0x0BF0EE 0x00): FSG: H Bridge 2 EGR Valve Circuit Open Load —>

<!— 0BF0EE (0x0BF0EE 0x00): H Bridge 2 EGR Valve Circuit Open Load —>

<!— 0CF0E3 (0x0CF0E3 0x00): FSG: Reserved 2 —>

<!— 0CF0E3 (0x0CF0E3 0x00): MU_ISP_T_TBD4_SRH —>

<!— 0CF0E3 (0x0CF0E3 0x00): Reserved 2 —>

<!— 0CF0E4 (0x0CF0E4 0x00): FSG: Reserved 1 —>

<!— 0CF0E4 (0x0CF0E4 0x00): MU_ISP_T_TBD4_SRL —>

<!— 0CF0E4 (0x0CF0E4 0x00): Reserved 1 —>

<!— 0D0E03 (0x0D0E03 0x00): Proportional Valve Bank 1 Circuit Failed High —>

<!— 0D0E04 (0x0D0E04 0x00): Proportional Valve Bank 1 Circuit Failed Low —>

<!— 0D0E06 (0x0D0E06 0x00): Current Flow on HS1 IM1 Too High —>

<!— 0D0E06 (0x0D0E06 0x00): Current Flow on HS1 IM1 too High —>

<!— 0DF0E3 (0x0DF0E3 0x00): Thermal Switch Circuit Failed High —>

<!— 0DF0E4 (0x0DF0E4 0x00): Thermal Switch Circuit Failed Low —>

<!— 0E0E03 (0x0E0E03 0x00): Proportional Valve Bank 2 Circuit Failed High —>

<!— 0E0E04 (0x0E0E04 0x00): Proportional Valve Bank 2 Circuit Failed Low —>

<!— 0EF0E3 (0x0EF0E3 0x00): FSG: Reserved 4 —>

<!— 0EF0E3 (0x0EF0E3 0x00): MU_ISP_T_TBD3_SRH —>

<!— 0EF0E3 (0x0EF0E3 0x00): Reserved 4 —>

<!— 0EF0E4 (0x0EF0E4 0x00): FSG: Reserved 3 —>

<!— 0EF0E4 (0x0EF0E4 0x00): MU_ISP_T_TBD3_SRL —>

<!— 0EF0E4 (0x0EF0E4 0x00): Reserved 3 —>

<!— 0F0E03 (0x0F0E03 0x00): MCM Internal Injector Power Supply Failed High —>

<!— 0F0E04 (0x0F0E04 0x00): MCM Internal Injector Power Supply Failed Low —>

<!— 0F0E0F (0x0F0E0F 0x00): MCM Internal Injector Power Supply Failed High Sporadic —>

<!— 0F0E0F (0x0F0E0F 0x00): MU_IS1_U_SPS_SPORATIC_SRH —>

<!— 0F0E11 (0x0F0E11 0x00): MCM internal Injector Power Supply Failed Low Sporadic —>

<!— 0F0E11 (0x0F0E11 0x00): MU_IS1_U_SPS_SPORATIC_SRL —>

<!— 0FF0E3 (0x0FF0E3 0x00): Electrical Water Separator Circuit Failed High —>

<!— 0FF0E3 (0x0FF0E3 0x00): EWS Circuit Failed High —>

<!— 0FF0E3 (0x0FF0E3 0x00): FSG: EWS Circuit Failed High —>

<!— 0FF0E4 (0x0FF0E4 0x00): Electrical Water Separator Circuit Failed Low —>

<!— 0FF0E4 (0x0FF0E4 0x00): EWS Circuit Failed Low —>

<!— 0FF0E4 (0x0FF0E4 0x00): FSG: EWS Circuit Failed Low —>

<!— 0FF0E5 (0x0FF0E5 0x00): Electrical Water Separator Circuit Failed Open —>

<!— 0FF0E5 (0x0FF0E5 0x00): EWS Circuit Failed Open —>

<!— 0FF0E5 (0x0FF0E5 0x00): FSG: EWS Circuit Failed Open —>

<!— 10F0E3 (0x10F0E3 0x00): Turbo Compound Valve Circuit Failed High —>

<!— 10F0E4 (0x10F0E4 0x00): Turbo Compound Valve Circuit Failed Low —>

<!— 10F0E5 (0x10F0E5 0x00): Turbo Compound Valve Circuit Failed Open —>

<!— 110B02 (0x110B02 0x00): Park Brake Status Not Plausible (Vehicle Moving) —>

<!— 12F0E3 (0x12F0E3 0x00): Function 19 Circuit Failed High —>

<!— 12F0E4 (0x12F0E4 0x00): Function 19 Circuit Failed Low —>

<!— 12F0E5 (0x12F0E5 0x00): Function 19 Circuit Failed Open —>

<!— 13150F (0x13150F 0x00): MU_RC4_IDLE_FUEL_QTY —>

<!— 13F0E3 (0x13F0E3 0x00): Service Push Button Circuit Failed High —>

<!— 16F0E3 (0x16F0E3 0x00): Function 22 Circuit Failed High —>

<!— 16F0E4 (0x16F0E4 0x00): Function 22 Circuit Failed Low —>

<!— 16F0E5 (0x16F0E5 0x00): Function 22 Circuit Failed Open —>

<!— 17F0E3 (0x17F0E3 0x00): Water Pump Circuit Failed High —>

<!— 17F0E4 (0x17F0E4 0x00): Water Pump Circuit Failed Low —>

<!— 17F0E5 (0x17F0E5 0x00): Water Pump Circuit Failed Open —>

<!— 18F0E3 (0x18F0E3 0x00): Function 25 Circuit Failed High —>

<!— 18F0E4 (0x18F0E4 0x00): Function 25 Circuit Failed Low —>

<!— 18F0E5 (0x18F0E5 0x00): Function 25 Circuit Failed Open —>

<!— 190E08 (0x190E08 0x00): FSG: Reserved 17 —>

<!— 190E08 (0x190E08 0x00): Reserved 17 —>

<!— 190E08 (0x190E08 0x00): Reserved 45 —>

<!— 19F0E3 (0x19F0E3 0x00): RCP Test Function 1 Circuit Failed High —>

<!— 19F0E4 (0x19F0E4 0x00): RCP Test Function 1 Circuit Failed Low —>

<!— 19F0E5 (0x19F0E5 0x00): RCP Test Function 1 Circuit Failed Open —>

<!— 1A0E1F (0x1A0E1F 0x00): Reserved 38 —>

<!— 1AF0E3 (0x1AF0E3 0x00): RCP Test Function 2 Circuit Failed High —>

<!— 1AF0E4 (0x1AF0E4 0x00): RCP Test Function 2 Circuit Failed Low —>

<!— 1AF0E5 (0x1AF0E5 0x00): RCP Test Function 2 Circuit Failed Open —>

<!— 1B0000 (0x1B0000 0x00): EGR Valve Failed to Attain Closed Position —>

<!— 1B0001 (0x1B0001 0x00): EGR Valve Failed to Attain Open Position —>

<!— 1B0002 (0x1B0002 0x00): EGR Valve Position Feedback Failed —>

<!— 1B0003 (0x1B0003 0x00): EGR Valve Position Circuit Failed High —>

<!— 1B0004 (0x1B0004 0x00): EGR Valve Position Circuit Failed Low —>

<!— 1B0007 (0x1B0007 0x00): MU_AM_EGR_SPRING_BROKEN —>

<!— 1B000A (0x1B000A 0x00): EGR Valve Position Deviation too High —>

<!— 1B000C (0x1B000C 0x00): EGR Valve Frozen —>

<!— 1B000E (0x1B000E 0x00): MU_EGR_INT_MON —>

<!— 1B0013 (0x1B0013 0x00): FSG: Smart Actuator Indicates Turbocharger Waste Gate Position Error —>

<!— 1B0013 (0x1B0013 0x00): Smart Actuator Indicates Turbo Charger Waste Gate Position Error —>

<!— 1B0013 (0x1B0013 0x00): Smart Actuator Indicates Turbocharger Waste Gate Position Error —>

<!— 1B060E (0x1B060E 0x00): Detect Unwanted ECU Change —>

<!— 1B060E (0x1B060E 0x00): FSG: Detect unwanted ECU change —>

<!— 1BF0E3 (0x1BF0E3 0x00): Volute Control Valve, Shorted to Battery —>

<!— 1BF0E4 (0x1BF0E4 0x00): Volute Control Valve, Shorted to Ground —>

<!— 1BF0E5 (0x1BF0E5 0x00): Volute Control Valve, Open Load —>

<!— 1CF0E3 (0x1CF0E3 0x00): Volute Shut Off Valve, Shorted to Battery —>

<!— 1CF0E4 (0x1CF0E4 0x00): Volute Shut Off Valve, Shorted to Ground —>

<!— 1CF0E5 (0x1CF0E5 0x00): Volute Shut Off Valve, Open Load —>

<!— 1DF0E3 (0x1DF0E3 0x00): Variable Camshaft Phase, Shorted to Battery —>

<!— 1DF0E4 (0x1DF0E4 0x00): Variable Camshaft Phase, Shorted to Ground —>

<!— 1DF0E5 (0x1DF0E5 0x00): Variable Camshaft Phase, Open Load —>

<!— 1EF0E3 (0x1EF0E3 0x00): Function 31 Circuit Failed High —>

<!— 1EF0E4 (0x1EF0E4 0x00): Function 31 Circuit Failed Low —>

<!— 1EF0E5 (0x1EF0E5 0x00): Function 31 Circuit Failed Open —>

<!— 230D03 (0x230D03 0x00): DEF Tank Heater Circuit Failed High —>

<!— 230D03 (0x230D03 0x00): Urea Tank Heater Circuit Failed High —>

<!— 230D04 (0x230D04 0x00): DEF Tank Heater Circuit Failed Low —>

<!— 230D04 (0x230D04 0x00): Urea Tank Heater Circuit Failed Low —>

<!— 230D05 (0x230D05 0x00): DEF Heater Circuit Failed Open —>

<!— 230D05 (0x230D05 0x00): DEF Tank Heater Circuit Failed Open —>

<!— 230D05 (0x230D05 0x00): Urea Heater Circuit Failed Open —>

<!— 230D05 (0x230D05 0x00): Urea Tank Heater Circuit Failed Open —>

<!— 230D11 (0x230D11 0x00): MU_CMP_PVH_UTH_OBD —>

<!— 25F0E7 (0x25F0E7 0x00): Smart Remote Actuator 2, Failsafe Mode, Motor On —>

<!— 25F0E8 (0x25F0E8 0x00): Smart Remote Actuator 2, Internal Test Running —>

<!— 25F0E9 (0x25F0E9 0x00): Smart Remote Actuator 2, Failsafe Mode, Motor Off —>

<!— 25F0EB (0x25F0EB 0x00): Smart Remote Actuator 2, Restricted Operability —>

<!— 25F0EE (0x25F0EE 0x00): Smart Remote Actuator 2, No Failsafe Mode, Motor Off —>

<!— 25F0EF (0x25F0EF 0x00): Smart Remote Actuator 2, Temperature Warning —>

<!— 25F0F0 (0x25F0F0 0x00): Smart Remote Actuator 2, Temperature Fault —>

<!— 25F0FF (0x25F0FF 0x00): Smart Remote Actuator 2, Unknown Error Code —>

<!— 261703 (0x261703 0x00): Differential Pressure Icooler Out Sensor Circuit Failed High —>

<!— 261704 (0x261704 0x00): Differential Pressure Icooler Out Sensor Circuit Failed Low —>

<!— 26170D (0x26170D 0x00): Icooler Out Differential Pressure Sensor Out of Calibration Low —>

<!— 26170E (0x26170E 0x00): Icooler Out Differential Pressure Sensor Out of Calibration High —>

<!— 261714 (0x261714 0x00): Icooler Out Differential Pressure Plausibility Fault, Pressure too High (Low Box) —>

<!— 261715 (0x261715 0x00): Icooler Out Differential Pressure Plausibility Fault, Pressure too Low (High Box) —>

<!— 26F0ED (0x26F0ED 0x00): FSG: Reserved 41 —>

<!— 26F0ED (0x26F0ED 0x00): Reserved 41 —>

<!— 26F0EE (0x26F0EE 0x00): FSG: Reserved 42 —>

<!— 26F0EE (0x26F0EE 0x00): Reserved 42 —>

<!— 271702 (0x271702 0x00): Water Pump Limp Home Mode —>

<!— 271707 (0x271707 0x00): Water Pump Mechanical Defect Detected —>

<!— 27F0F0 (0x27F0F0 0x00): FSG: Max Power Deficit —>

<!— 27F0F0 (0x27F0F0 0x00): Max Power Deficit —>

<!— 27F0F2 (0x27F0F2 0x00): FSG: Max Power Excess —>

<!— 27F0F2 (0x27F0F2 0x00): Max Power Excess —>

<!— 281703 (0x281703 0x00): H Bridge 2 EGR Valve Circiut Shorted to Battery —>

<!— 281704 (0x281704 0x00): H Bridge 2 EGR Valve Circuit Shorted to Ground —>

<!— 281705 (0x281705 0x00): H Bridge 2 EGR Valve Short Circuit/ Over Current —>

<!— 28170E (0x28170E 0x00): H Bridge 2 EGR Valve Circuit Open Load —>

<!— 2A050E (0x2A050E 0x00): Multiple Cylinder Misfire Detecetd —>

<!— 2A050E (0x2A050E 0x00): Multiple Cylinder Misfire Detected —>

<!— 2A051F (0x2A051F 0x00): FSG: Multiple cylinder misfire detected at idle —>

<!— 2A051F (0x2A051F 0x00): Multiple Cylinder Misfire Detected at Idle —>

<!— 2A1503 (0x2A1503 0x00): FMU High Side Short-Circuit to Battery —>

<!— 2A1504 (0x2A1504 0x00): FMU Low Side Short-Circuit to Ground —>

<!— 2B050B (0x2B050B 0x00): Cylinder #1 Misfire Detected —>

<!— 2B050B (0x2B050B 0x00): Cylinder 1 Misfire detected —>

<!— 2B050E (0x2B050E 0x00): FSG: Idle Smoothness Control / Cylinder #1 Quantity Excess at Idle —>

<!— 2B050E (0x2B050E 0x00): Idle Smoothness Control / Cylinder #1 Quantity Excess at Idle —>

<!— 2B051F (0x2B051F 0x00): FSG: Idle Smoothness Control / Cylinder #1 Quantity Deficit at Idle —>

<!— 2B051F (0x2B051F 0x00): Idle Smoothness Control / Cylinder #1 Quantity Deficit at Idle —>

<!— 2C050B (0x2C050B 0x00): Cylinder #2 Misfire Detected —>

<!— 2C050B (0x2C050B 0x00): Cylinder 2 Misfire detected —>

<!— 2C050E (0x2C050E 0x00): FSG: Idle Smoothness Control / Cylinder #2 Quantity Excess at Idle —>

<!— 2C050E (0x2C050E 0x00): Idle Smoothness Control / Cylinder #2 Quantity Excess at Idle —>

<!— 2C051F (0x2C051F 0x00): FSG: Idle Smoothness Control / Cylinder #2 Quantity Deficit at Idle —>

<!— 2C051F (0x2C051F 0x00): Idle Smoothness Control / Cylinder #2 Quantity Deficit at Idle —>

<!— 2CF0EE (0x2CF0EE 0x00): FSG: Intermittent conection in sensor electric circuit 1 —>

<!— 2CF0EE (0x2CF0EE 0x00): Intermittent conection in sensor electric circuit 1 —>

<!— 2CF0EE (0x2CF0EE 0x00): Intermittent Connection in Sensor Electric Circuit 1 —>

<!— 2CF0FF (0x2CF0FF 0x00): FSG: Intermittent conection in sensor electric circuit 2 —>

<!— 2CF0FF (0x2CF0FF 0x00): Intermittent Connection in Sensor Electric Circuit 2 —>

<!— 2D050B (0x2D050B 0x00): Cylinder #3 Misfire Detected —>

<!— 2D050B (0x2D050B 0x00): Cylinder 3 Misfire detected —>

<!— 2D050E (0x2D050E 0x00): FSG: Idle Smoothness Control / Cylinder #3 Quantity Excess at Idle —>

<!— 2D050E (0x2D050E 0x00): Idle Smoothness Control / Cylinder #3 Quantity Excess at Idle —>

<!— 2D051F (0x2D051F 0x00): FSG: Idle Smoothness Control / Cylinder #3 Quantity Deficit at Idle —>

<!— 2D051F (0x2D051F 0x00): Idle Smoothness Control / Cylinder #3 Quantity Deficit at Idle —>

<!— 2DF0E2 (0x2DF0E2 0x00): FSG: Variable Camshaft Phase, Position Deviation —>

<!— 2DF0E2 (0x2DF0E2 0x00): MU_AM_VCP_POS_DEV —>

<!— 2DF0E2 (0x2DF0E2 0x00): Variable Camshaft Phase, Position Deviation —>

<!— 2DF0E7 (0x2DF0E7 0x00): FSG: Variable Camshaft Phase, Clamb Position —>

<!— 2DF0E7 (0x2DF0E7 0x00): MU_AM_VCP_CLAMP —>

<!— 2DF0E7 (0x2DF0E7 0x00): Variable Camshaft Phase, Clamb Position —>

<!— 2DF0EA (0x2DF0EA 0x00): FSG: Variable Camshaft Phase, Slow Response —>

<!— 2DF0EA (0x2DF0EA 0x00): MU_AM_VCP_SLOW_RESPONSE —>

<!— 2DF0EA (0x2DF0EA 0x00): Variable Camshaft Phase, Slow Response —>

<!— 2DF0EE (0x2DF0EE 0x00): FSG: Variable Camshaft Phase Sensor Adaption Fail —>

<!— 2DF0EE (0x2DF0EE 0x00): MU_AM_VCP_SENS_ADAPT_FAIL —>

<!— 2DF0EE (0x2DF0EE 0x00): Variable Camshaft Phase Sensor Adaption Fail —>

<!— 2DF0FF (0x2DF0FF 0x00): FSG: Variable Camshaft Phase, at State Joggling —>

<!— 2DF0FF (0x2DF0FF 0x00): MU_AM_VCP_JOG_FAIL —>

<!— 2DF0FF (0x2DF0FF 0x00): Variable Camshaft Phase, at State Joggling —>

<!— 2E050B (0x2E050B 0x00): Cylinder #4 Misfire Detected —>

<!— 2E050B (0x2E050B 0x00): Cylinder 4 Misfire detected —>

<!— 2E050E (0x2E050E 0x00): FSG: Idle Smoothness Control / Cylinder #4 Quantity Excess at Idle —>

<!— 2E050E (0x2E050E 0x00): Idle Smoothness Control / Cylinder #4 Quantity Excess at Idle —>

<!— 2E051F (0x2E051F 0x00): FSG: Idle Smoothness Control / Cylinder #4 Quantity Deficit at Idle —>

<!— 2E051F (0x2E051F 0x00): Idle Smoothness Control / Cylinder #4 Quantity Deficit at Idle —>

<!— 2EF0E0 (0x2EF0E0 0x00): FSG: Variable Camshaft Phase, Temperature to high —>

<!— 2EF0E0 (0x2EF0E0 0x00): MU_AM_VCP_TEMP_IND_HIGH —>

<!— 2EF0E0 (0x2EF0E0 0x00): Variable Camshaft Phase, Temperature too High —>

<!— 2EF0E0 (0x2EF0E0 0x00): Variable Camshaft Phase, Temperature to high —>

<!— 2EF0EE (0x2EF0EE 0x00): Dashboard Doesn’t Get MCM DM1 Information —>

<!— 2EF0EE (0x2EF0EE 0x00): FSG: Dashboard doesn’t get MCM DM1 information —>

<!— 2EF0FF (0x2EF0FF 0x00): Dashboard DM1 Defect —>

<!— 2EF0FF (0x2EF0FF 0x00): FSG: Dashboard DM1 defect —>

<!— 2F0403 (0x2F0403 0x00): Fan Stage 2 Circuit Failed High —>

<!— 2F0404 (0x2F0404 0x00): Fan Stage 2 Circuit Failed Low —>

<!— 2F0405 (0x2F0405 0x00): Fan Stage 2 Circuit Failed Open —>

<!— 2F050B (0x2F050B 0x00): Cylinder #5 Misfire Detected —>

<!— 2F050B (0x2F050B 0x00): Cylinder 5 Misfire detected —>

<!— 2F050E (0x2F050E 0x00): FSG: Idle Smoothness Control / Cylinder #5 Quantity Excess at Idle —>

<!— 2F050E (0x2F050E 0x00): Idle Smoothness Control / Cylinder #5 Quantity Excess at Idle —>

<!— 2F051F (0x2F051F 0x00): FSG: Idle Smoothness Control / Cylinder #5 Quantity Deficit at Idle —>

<!— 2F051F (0x2F051F 0x00): Idle Smoothness Control / Cylinder #5 Quantity Deficit at Idle —>

<!— 2FF0EE (0x2FF0EE 0x00): EGR System Parametrization Failure —>

<!— 300403 (0x300403 0x00): Jake Brake Stage 1 Circuit Failed High —>

<!— 300404 (0x300404 0x00): Jake Brake Stage 1 Circuit Failed Low —>

<!— 300405 (0x300405 0x00): Jake Brake Stage 1 Circuit Failed Open —>

<!— 30050B (0x30050B 0x00): Cylinder #6 Misfire Detected —>

<!— 30050B (0x30050B 0x00): Cylinder 6 Misfire Detected —>

<!— 30050E (0x30050E 0x00): FSG: Idle Smoothness Control / Cylinder #6 Quantity Excess at Idle —>

<!— 30050E (0x30050E 0x00): Idle Smoothness Control / Cylinder #6 Quantity Excess at Idle —>

<!— 30051F (0x30051F 0x00): FSG: Idle Smoothness Control / Cylinder #6 Quantity Deficit at Idle —>

<!— 30051F (0x30051F 0x00): Idle Smoothness Control / Cylinder #6 Quantity Deficit at Idle —>

<!— 30F0E8 (0x30F0E8 0x00): FSG: Intermittent conection in sensor electric circuit 3 —>

<!— 30F0E8 (0x30F0E8 0x00): Intermittent Connection in Sensor Electric Circuit 3 —>

<!— 310403 (0x310403 0x00): Jake Brake Stage 2 Circuit Failed High —>

<!— 310404 (0x310404 0x00): Jake Brake Stage 2 Circuit Failed Low —>

<!— 310405 (0x310405 0x00): Jake Brake Stage 2 Circuit Failed Open —>

<!— 31050B (0x31050B 0x00): Cylinder #7 Misfire Detected —>

<!— 31050B (0x31050B 0x00): Cylinder 7 Misfire Detected —>

<!— 31050E (0x31050E 0x00): FSG: Idle Smoothness Control / Cylinder #7 Quantity Excess at Idle —>

<!— 31050E (0x31050E 0x00): Idle Smoothness Control / Cylinder #7 Quantity Excess at Idle —>

<!— 31051F (0x31051F 0x00): FSG: Idle Smoothness Control / Cylinder #7 Quantity Deficit at Idle —>

<!— 31051F (0x31051F 0x00): Idle Smoothness Control / Cylinder #7 Quantity Deficit at Idle —>

<!— 31F0E8 (0x31F0E8 0x00): FSG: Intermittent conection in sensor electric circuit 4 —>

<!— 31F0E8 (0x31F0E8 0x00): Intermittent Connection in Sensor Electric Circuit 4 —>

<!— 32050B (0x32050B 0x00): Cylinder #8 Misfire Detected —>

<!— 32050B (0x32050B 0x00): Cylinder 8 Misfire Detected —>

<!— 32050E (0x32050E 0x00): FSG: Idle Smoothness Control / Cylinder #8 Quantity Excess at Idle —>

<!— 32050E (0x32050E 0x00): Idle Smoothness Control / Cylinder #8 Quantity Excess at Idle —>

<!— 32051F (0x32051F 0x00): FSG: Idle Smoothness Control / Cylinder #8 Quantity Deficit at Idle —>

<!— 32051F (0x32051F 0x00): Idle Smoothness Control / Cylinder #8 Quantity Deficit at Idle —>

<!— 32F0E2 (0x32F0E2 0x00): FSG: O2 Sensor, Heater Invalid Sensor Temperature Measurement —>

<!— 32F0E2 (0x32F0E2 0x00): MU_EGCP_DIA_TTIP_ADJ —>

<!— 32F0E2 (0x32F0E2 0x00): O2 Sensor, Heater Invalid Sensor Temperature Measurement —>

<!— 32F0E3 (0x32F0E3 0x00): MU_EGCP_DIA_SC_ERR —>

<!— 32F0E3 (0x32F0E3 0x00): O2 Sensor Circuit Bank 1 Sensor 1, Short Circuit —>

<!— 32F0E5 (0x32F0E5 0x00): MU_EGCP_DIA_OC_VN —>

<!— 32F0E5 (0x32F0E5 0x00): O2 Sensor Circuit Bank 1 Sensor 1, Open Circuit on line Vn —>

<!— 32F0E5 (0x32F0E5 0x00): O2 Sensor Circuit Bank 1 Sensor 1, Open Circuit on Line Vn —>

<!— 32F0EE (0x32F0EE 0x00): FSG: O2 Sensor, Lambda Rationality During No Fueling —>

<!— 32F0EE (0x32F0EE 0x00): MU_EGCP_DIA_SENS_DEF —>

<!— 32F0EE (0x32F0EE 0x00): O2 Sensor, Lambda Rationality During No Fueling —>

<!— 330002 (0x330002 0x00): Intake Throttle Position Deviation Error —>

<!— 330003 (0x330003 0x00): Intake Air Throttle Circuit Failed High —>

<!— 330004 (0x330004 0x00): Intake Air Throttle Circuit Failed Low —>

<!— 33000A (0x33000A 0x00): MU_IAT_POS_FROZEN —>

<!— 330012 (0x330012 0x00): MU_RC4_IAT_RAT —>

<!— 33F0E5 (0x33F0E5 0x00): MU_EGCP_DIA_OC_VG —>

<!— 33F0E5 (0x33F0E5 0x00): O2 Sensor Circuit Bank 1 Sensor 1, Open Circuit on line Vg —>

<!— 33F0E5 (0x33F0E5 0x00): O2 Sensor Circuit Bank 1 Sensor 1, Open Circuit on Line Vg —>

<!— 33F0E9 (0x33F0E9 0x00): MU_EGCP_DIA_SPI_WR_ERR —>

<!— 33F0EB (0x33F0EB 0x00): MU_EGCP_DIA_SPI_INI_ERR —>

<!— 34F0E5 (0x34F0E5 0x00): MU_EGCP_DIA_OC_VIP —>

<!— 34F0E5 (0x34F0E5 0x00): O2 Sensor Circuit Bank 1 Sensor 1, Open Circuit on line Vip —>

<!— 34F0E5 (0x34F0E5 0x00): O2 Sensor Circuit Bank 1 Sensor 1, Open Circuit on Line Vip —>

<!— 350403 (0x350403 0x00): Quantity Control Valve (Low Side) error —>

<!— 350403 (0x350403 0x00): Quantity Control Valve (Low Side) Error —>

<!— 350404 (0x350404 0x00): Quantity Control Valve (High Side) Error —>

<!— 350405 (0x350405 0x00): Quantity Control Valve Error, Current Too Low —>

<!— 350405 (0x350405 0x00): Quantity Control Valve Error, Current too Low —>

<!— 350406 (0x350406 0x00): FSG: Quantity Control Valve, Desired Current Doesn’t match actual current —>

<!— 350406 (0x350406 0x00): Quantity Control Valve, Desired Current Doesn’t Match Actual Current —>

<!— 35040E (0x35040E 0x00): Leakage in High Pressure Fuel System Too High (Leak Down Test) —>

<!— 35040E (0x35040E 0x00): Leakage in High Pressure Fuel System too High (Leak Down Test) —>

<!— 35041F (0x35041F 0x00): Excessive Time to Enter Closed Loop Fuel Pressure Control —>

<!— 35041F (0x35041F 0x00): Excessive Time To Enter Closed Loop Fuel Pressure Control —>

<!— 35041F (0x35041F 0x00): FSG: Excessive Time To Enter Closed Loop Fuel Pressure Control —>

<!— 35F0E5 (0x35F0E5 0x00): MU_EGCP_DIA_OC_VRC —>

<!— 35F0E5 (0x35F0E5 0x00): O2 Sensor Circuit Bank 1 Sensor 1, Open Circuit on line Vrc —>

<!— 35F0E5 (0x35F0E5 0x00): O2 Sensor Circuit Bank 1 Sensor 1, Open Circuit on Line Vrc —>

<!— 36F0E0 (0x36F0E0 0x00): MU_PBS_INTERNAL_ERROR —>

<!— 36F0E1 (0x36F0E1 0x00): MU_PBS_CRITICAL_ERROR —>

<!— 36F0E2 (0x36F0E2 0x00): MU_PBS_AIR_SUPPLY_ERR —>

<!— 36F0E3 (0x36F0E3 0x00): MU_PBS_U_BAT_HIGH —>

<!— 36F0E4 (0x36F0E4 0x00): MU_PBS_U_BAT_LOW —>

<!— 36F0E7 (0x36F0E7 0x00): MU_PBS_VALVE_SUPPLY —>

<!— 36F0E9 (0x36F0E9 0x00): MU_PBS_CAN_ERROR —>

<!— 36F0EB (0x36F0EB 0x00): MU_PBS_GENERAL_ERROR —>

<!— 36F0ED (0x36F0ED 0x00): MU_PBS_CONF_ERR —>

<!— 36F0EE (0x36F0EE 0x00): MU_PBS_PWR_SUPPLY —>

<!— 36F0EE (0x36F0EE 0x00): MU_PBS_SW_CHECK_ERR —>

<!— 36F0EF (0x36F0EF 0x00): MU_PBS_TEMP_ERROR —>

<!— 36F0F0 (0x36F0F0 0x00): MU_PBS_PAR_ERROR —>

<!— 36F0F3 (0x36F0F3 0x00): CAN3 Electrical Failure —>

<!— 36F0F3 (0x36F0F3 0x00): CAN3 electrical failure —>

<!— 38F0E0 (0x38F0E0 0x00): Classic Immobilizer, Number of Keys Limited to 8 —>

<!— 38F0E0 (0x38F0E0 0x00): FSG: Classic Immobilizer, number of keys limited to 8 —>

<!— 38F0E0 (0x38F0E0 0x00): tbd —>

<!— 38F0E1 (0x38F0E1 0x00): Classic Immobilizer, Counter Overflow —>

<!— 38F0E1 (0x38F0E1 0x00): FSG: Classic Immobilizer, counter overflow —>

<!— 38F0E1 (0x38F0E1 0x00): tbd —>

<!— 38F0E2 (0x38F0E2 0x00): Classic Immobilizer, X5 Cancelled —>

<!— 38F0E2 (0x38F0E2 0x00): FSG: Classic Immobilizer, X5 cancelled —>

<!— 38F0E2 (0x38F0E2 0x00): tbd —>

<!— 38F0E3 (0x38F0E3 0x00): Classic Immobilizer, No TPC via CAN —>

<!— 38F0E3 (0x38F0E3 0x00): FSG: Classic Immobilizer, no TPC via CAN —>

<!— 38F0E3 (0x38F0E3 0x00): tbd —>

<!— 38F0E4 (0x38F0E4 0x00): Classic Immobilizer, No TPC via Starter Pin —>

<!— 38F0E4 (0x38F0E4 0x00): FSG: Classic Immobilizer, no TPC via starter pin —>

<!— 38F0E4 (0x38F0E4 0x00): tbd —>

<!— 38F0E5 (0x38F0E5 0x00): Classic Immobilizer, Code Valid But False —>

<!— 38F0E5 (0x38F0E5 0x00): FSG: Classic Immobilizer, code valid but false —>

<!— 38F0E5 (0x38F0E5 0x00): tbd —>

<!— 38F0E6 (0x38F0E6 0x00): FSG: Injection inhibited by immobilizer (wrong key or CAN or EIS issue) —>

<!— 38F0E6 (0x38F0E6 0x00): Injection Inhibited by Immobilizer (Wrong Key or CAN or EIS Issue) —>

<!— 38F0E6 (0x38F0E6 0x00): tbd —>

<!— 39F0E3 (0x39F0E3 0x00): FMU High Side Short-Circuit to Battery —>

<!— 39F0E3 (0x39F0E3 0x00): FMU highside short-circuit to battery —>

<!— 39F0E3 (0x39F0E3 0x00): FSG: FMU highside short-circuit to battery —>

<!— 39F0E3 (0x39F0E3 0x00): Quantity Control Valve ( High Side ) error —>

<!— 39F0E4 (0x39F0E4 0x00): FSG: Quantity Control Valve ( High side) error —>

<!— 39F0E4 (0x39F0E4 0x00): Quantity Control Valve (High side) error —>

<!— 39F0E4 (0x39F0E4 0x00): Quantity Control Valve (High Side) Error —>

<!— 3AF0E4 (0x3AF0E4 0x00): FMU Low Side Short-Circuit to Ground —>

<!— 3AF0E4 (0x3AF0E4 0x00): FMU lowside short-circuit to ground —>

<!— 3AF0E4 (0x3AF0E4 0x00): FSG: FMU lowside short-circuit to ground —>

<!— 3AF0E4 (0x3AF0E4 0x00): Quantity Control Valve ( Low Side ) error —>

<!— 3BF0E3 (0x3BF0E3 0x00): FSG: PCV highside short-circuit to battery —>

<!— 3BF0E3 (0x3BF0E3 0x00): PCV High Side Short-Circuit to Battery —>

<!— 3BF0E3 (0x3BF0E3 0x00): Pressure Control Valve ( High side) error —>

<!— 3BF0E4 (0x3BF0E4 0x00): FSG: Pressure control valve ( High side ) error —>

<!— 3BF0E4 (0x3BF0E4 0x00): Pressure Control Valve (High Side) Error —>

<!— 3CF0E3 (0x3CF0E3 0x00): Pressure Control Valve (Low Side) Error —>

<!— 3CF0E4 (0x3CF0E4 0x00): FSG: PCV lowside short-circuit to ground —>

<!— 3CF0E4 (0x3CF0E4 0x00): PCV Low Side Short-Circuit to Ground —>

<!— 3CF0E4 (0x3CF0E4 0x00): Pressure Control Valve ( Low side) error —>

<!— 3DF0EE (0x3DF0EE 0x00): FSG: SW-Reset executed by MCM2-Level2 monitoring due to error in engine speed plausibilisation. —>

<!— 3DF0EE (0x3DF0EE 0x00): FSG: SW-Reset executed by MCM2-Level2 monitoring due to error in engine speed plausibilisation —>

<!— 3DF0EE (0x3DF0EE 0x00): MU_SCM_SPEED_RESET_LEV2 —>

<!— 3DF0EE (0x3DF0EE 0x00): SW-Reset Executed by MCM2-Level2 Monitoring due to Error in Engine Speed Plausibilisation —>

<!— 3DF0FF (0x3DF0FF 0x00): FSG: SW-Reset executed by MCM2-Level2 monitoring due to error in fuel-cutoff plausibilisation —>

<!— 3DF0FF (0x3DF0FF 0x00): MU_SCM_FCUT_RESET_LEV2 —>

<!— 3DF0FF (0x3DF0FF 0x00): SW-Reset Executed by MCM2-Level2 Monitoring due to Error in Fuel-Cutoff Plausibilisation —>

<!— 3EF0FF (0x3EF0FF 0x00): MU_CPC_32 —>

<!— 3FF0FF (0x3FF0FF 0x00): MU_CPC_33 —>

<!— 40F0FF (0x40F0FF 0x00): MU_CPC_34 —>

<!— 41F0FF (0x41F0FF 0x00): MU_EPF_BROKEN_BELT_DETECT —>

<!— 42F0EE (0x42F0EE 0x00): MU_TSA_BRK_FAIL_ON_BANK1 —>

<!— 42F0FF (0x42F0FF 0x00): MU_TSA_BRK_FAIL_BANK1 —>

<!— 43F0EE (0x43F0EE 0x00): MU_TSA_BRK_FAIL_ON_BANK2 —>

<!— 43F0FF (0x43F0FF 0x00): MU_TSA_BRK_FAIL_BANK2 —>

<!— 441501 (0x441501 0x00): CCV Speed Sensor RPM to Low —>

<!— 441501 (0x441501 0x00): Engine Crankcase Breather Oil Separator Speed too Low —>

<!— 44F0E2 (0x44F0E2 0x00): MU_EGCP_DIA_LBD_FIRED_HIGH —>

<!— 44F0E7 (0x44F0E7 0x00): MU_EGCP_DIAG_LSL_DYN —>

<!— 44F0EB (0x44F0EB 0x00): MU_EGCP_DIA_VLS_OFS_LIM —>

<!— 44F0EE (0x44F0EE 0x00): MU_EGCP_DIA_I_PMP_LIM —>

<!— 44F0FF (0x44F0FF 0x00): MU_EGCP_DIA_V_PMP_LIM —>

<!— 450A02 (0x450A02 0x00): Turbo Charger Compressor Outlet Tempemperature Sensor, General Temperature Plausibility Error —>

<!— 450A02 (0x450A02 0x00): Turbocharger Compressor Outlet Temp. Sensor, General Temp. Plausibility Error —>

<!— 450A03 (0x450A03 0x00): Turbo Charger Compressor Outlet Temperature Circuit Failed High —>

<!— 450A03 (0x450A03 0x00): Turbocharger Compressor Outlet Temperature Circuit Failed High —>

<!— 450A04 (0x450A04 0x00): Turbo Charger Compressor Outlet Temperature Circuit Failed Low —>

<!— 450A04 (0x450A04 0x00): Turbocharger Compressor Outlet Temperature Circuit Failed Low —>

<!— 450A14 (0x450A14 0x00): Turbo Charger Out Temperature, Temperature too High (Low Box) —>

<!— 450A14 (0x450A14 0x00): Turbocharger Out Temperature, Temperature Too High (Low Box) —>

<!— 450A15 (0x450A15 0x00): Turbo Charger Out Temperature, Temperature too Low (High Box) —>

<!— 450A15 (0x450A15 0x00): Turbocharger Out Temperature, Temperature Too Low (High Box) —>

<!— 450A1F (0x450A1F 0x00): MU_RC4_T_COMP_OUT_GEN2 —>

<!— 45F0FF (0x45F0FF 0x00): MU_SCM_SPEED_LIMIT_LEV2 —>

<!— 460002 (0x460002 0x00): J1939 Park Brake Switch Signal from Source #1 is erratic —>

<!— 460002 (0x460002 0x00): J1939 Park Brake Switch Signal from Source #1 is Erratic —>

<!— 460009 (0x460009 0x00): J1939 Park Brake Switch Signal from Source #2 is missing —>

<!— 460009 (0x460009 0x00): J1939 Park Brake Switch Signal from Source #2 is Missing —>

<!— 46000A (0x46000A 0x00): J1939 Park Brake Switch Signal from Source #3 is erratic —>

<!— 46000A (0x46000A 0x00): J1939 Park Brake Switch Signal from Source #3 is Erratic —>

<!— 46000D (0x46000D 0x00): J1939 Park Brake Switch Signal from Source #1 is missing —>

<!— 46000D (0x46000D 0x00): J1939 Park Brake Switch Signal from Source #1 is Missing —>

<!— 46000E (0x46000E 0x00): J1939 Park Brake Switch Signal from Source #3 is missing —>

<!— 46000E (0x46000E 0x00): J1939 Park Brake Switch Signal from Source #3 is Missing —>

<!— 460013 (0x460013 0x00): J1939 Park Brake Switch Signal from Source #2 is erratic —>

<!— 460013 (0x460013 0x00): J1939 Park Brake Switch Signal from Source #2 is Erratic —>

<!— 460A02 (0x460A02 0x00): Difference Intake Manifold and I Cooler Temperature Out Less Than Threshold (High Box) —>

<!— 460A02 (0x460A02 0x00): Difference Intake Manifold and Icooler Temperature Out Less Than Threshold (High Box) —>

<!— 460A03 (0x460A03 0x00): Charge Air Cooler Outlet Temperature Circuit Failed High —>

<!— 460A04 (0x460A04 0x00): Charge Air Cooler Outlet Temperature Circuit Failed Low —>

<!— 460A0B (0x460A0B 0x00): Charge Air Cooler Outlet Temperature Sensor Plausibility Error —>

<!— 460A0F (0x460A0F 0x00): Cooling Efficency of Icooler too Low —>

<!— 460A10 (0x460A10 0x00): Chage Air Cooler Performance Monitor —>

<!— 460A10 (0x460A10 0x00): Charge Air Cooler Performance Monitor —>

<!— 460A14 (0x460A14 0x00): Charge Air Outlet Temperature Drift (Low box) —>

<!— 460A14 (0x460A14 0x00): Charge Air Outlet Temperature Drift (Low Box) —>

<!— 460A15 (0x460A15 0x00): Charge Air Outlet Temperature Drift (High box) —>

<!— 460A15 (0x460A15 0x00): Charge Air Outlet Temperature Drift (High Box) —>

<!— 460A1F (0x460A1F 0x00): MU_RC4_T_ICOOLER_OUT_GEN2 —>

<!— 46F0E9 (0x46F0E9 0x00): FBS3 Injection Inhibit due to Keyline Lock —>

<!— 46F0EA (0x46F0EA 0x00): FBS3 Injection Inhibit due to Wrong Key —>

<!— 46F0EB (0x46F0EB 0x00): FBS3 Injection Inhibit due to Transport Protection —>

<!— 46F0ED (0x46F0ED 0x00): FBS3 Injection Inhibit due to Expired Prelease Time without Authentification —>

<!— 46F0EE (0x46F0EE 0x00): FBS3 Injection Inhibit due to Expired Prelease Time Mulitple Times (CAN or EIS Failure) —>

<!— 46F0EF (0x46F0EF 0x00): FBS3 Injection Inhibit due to Odometer Lock Function —>

<!— 46F0F0 (0x46F0F0 0x00): MU_IMB_FBS_HASH_CYC_HIGH —>

<!— 46F0F3 (0x46F0F3 0x00): FBS3 Injection Inhibit due to Missing EIS CAN Signales —>

<!— 46F0F5 (0x46F0F5 0x00): FBS3 t_count Value Expired —>

<!— 46F0FF (0x46F0FF 0x00): FBS3 Data Flash Defect, Exchange ECU —>

<!— 46F0FF (0x46F0FF 0x00): FGS: FBS3 data flash defect, exchange ECU —>

<!— 47050E (0x47050E 0x00): Air Compressor Clutch —>

<!— 470A01 (0x470A01 0x00): FSG: Unexceptable long time in smoke mode —>

<!— 470A01 (0x470A01 0x00): Unexceptable Long Time in Smoke Mode —>

<!— 470A02 (0x470A02 0x00): Turbo Charger / Super Charger Boost System Performance —>

<!— 470A02 (0x470A02 0x00): Turbocharger/Supercharger Boost System Performance —>

<!— 470A03 (0x470A03 0x00): Charge Air Cooler Outlet Pressure Circuit Failed High —>

<!— 470A04 (0x470A04 0x00): Charge Air Cooler Outlet Pressure Circuit Failed Low —>

<!— 470A0E (0x470A0E 0x00): Charge Air Control, Pressure not plausible in brake mode —>

<!— 470A0E (0x470A0E 0x00): Charge Air Control, Pressure Not Plausible in Brake Mode —>

<!— 470A0F (0x470A0F 0x00): MU_SMOKE_MODE_TOO_FREQ —>

<!— 470A14 (0x470A14 0x00): Intake Manifold Pressure Plausibility (Low Box) —>

<!— 470A15 (0x470A15 0x00): Intake Manifold Pressure Plausibility Error, Pressure Too Low (High Box) —>

<!— 470A15 (0x470A15 0x00): Intake Manifold Pressure Plausibility Error, Pressure too Low (High Box) —>

<!— 47F0E3 (0x47F0E3 0x00): MU_PBS_THRO_ENG_SC_BATT —>

<!— 47F0E4 (0x47F0E4 0x00): MU_PBS_THRO_ENG_SC_GND —>

<!— 47F0E5 (0x47F0E5 0x00): MU_PBS_THRO_ENG_OL —>

<!— 48F0E2 (0x48F0E2 0x00): MU_PBS_P_OUT_DEV —>

<!— 49F0E2 (0x49F0E2 0x00): MU_PBS_P_IN_DEV —>

<!— 4AF0E0 (0x4AF0E0 0x00): MU_PV_B_SHDOWN_OVERVOLTAGE —>

<!— 4AF0E0 (0x4AF0E0 0x00): Overvoltage PV_B Shut Off —>

<!— 4B0E03 (0x4B0E03 0x00): Injector Cylinder #1 Spill Control Valve Abnormal Operation (MAX) —>

<!— 4B0E03 (0x4B0E03 0x00): Injector Cylinder #1 Spill Control Valve («Amplifier»), Abnormal Operation (MAX) —>

<!— 4B0E04 (0x4B0E04 0x00): Injector Cylinder #1 Spill Control Valve Abnormal Operation (MIN) —>

<!— 4B0E04 (0x4B0E04 0x00): Injector Cylinder #1 Spill Control Valve («Amplifier»), Abnormal Operation (MIN) —>

<!— 4B0E05 (0x4B0E05 0x00): Injector Cylinder #1 Spill Control Valve («Amplifier»), Circuit Open —>

<!— 4B0E05 (0x4B0E05 0x00): MU_OFD_CYL1_PUMP_OPEN_LOAD —>

<!— 4B0E06 (0x4B0E06 0x00): «Injector Cylinder #1 Spill Control Valve («»Amplifier»»), Valve Shorted Circuit » —>

<!— 4B0E06 (0x4B0E06 0x00): Injector Cylinder #1 Spill Control Valve («Amplifier»), Valve Shorted Circuit —>

<!— 4B0E0A (0x4B0E0A 0x00): «Injector Cylinder #1 Spill Control Valve («»Amplifier»») Abnormal Rate of Change» —>

<!— 4B0E0A (0x4B0E0A 0x00): Injector Cylinder #1 Spill Control Valve («Amplifier») Abnormal Rate of Change —>

<!— 4B0E0A (0x4B0E0A 0x00): Injector Cylinder #1 Spill Control Valve («Amplifier»), Abnormal Rate of Change —>

<!— 4BF0E2 (0x4BF0E2 0x00): MU_IS4_CPC_CLOCK_SRC —>

<!— 4BF0EA (0x4BF0EA 0x00): MU_ISP_MCM_TIME_RAT_ERROR —>

<!— 4BF0EF (0x4BF0EF 0x00): MU_RC4_ENG_ON_TIM_PLAUS —>

<!— 4BF0F1 (0x4BF0F1 0x00): MU_RC4_ENG_OFF_TIM_PLAUS —>

<!— 4BF0F2 (0x4BF0F2 0x00): MU_IS4_RTC_ENG_OFF_RAT_CHK —>

<!— 4BF0F3 (0x4BF0F3 0x00): MU_CPC_CLOCK_DATA_SNA —>

<!— 4C0E03 (0x4C0E03 0x00): Injector Cylinder #2 Spill Control Valve Abnormal Operation (MAX) —>

<!— 4C0E03 (0x4C0E03 0x00): Injector Cylinder #2 Spill Control Valve («Amplifier»), Abnormal Operation (MAX) —>

<!— 4C0E04 (0x4C0E04 0x00): Injector Cylinder #2 Spill Control Valve Abnormal Operation (MIN) —>

<!— 4C0E04 (0x4C0E04 0x00): Injector Cylinder #2 Spill Control Valve («Amplifier»), Abnormal Operation (MIN) —>

<!— 4C0E05 (0x4C0E05 0x00): Injector Cylinder #2 Spill Control Valve («Amplifier»), Circuit Open —>

<!— 4C0E05 (0x4C0E05 0x00): MU_OFD_CYL2_PUMP_OPEN_LOAD —>

<!— 4C0E06 (0x4C0E06 0x00): «Injector Cylinder #2 Spill Control Valve («»Amplifier»»), Valve Shorted Circuit » —>

<!— 4C0E06 (0x4C0E06 0x00): Injector Cylinder #2 Spill Control Valve («Amplifier»), Valve Shorted Circuit —>

<!— 4C0E0A (0x4C0E0A 0x00): «Injector Cylinder #2 Spill Control Valve («»Amplifier»») Abnormal Rate of Change» —>

<!— 4C0E0A (0x4C0E0A 0x00): Injector Cylinder #2 Spill Control Valve («Amplifier») Abnormal Rate of Change —>

<!— 4C0E0A (0x4C0E0A 0x00): Injector Cylinder #2 Spill Control Valve («Amplifier»), Abnormal Rate of Change —>

<!— 4CF0F0 (0x4CF0F0 0x00): Fuel Rail Pressure too Low , Similar Condition —>

<!— 4CF0F0 (0x4CF0F0 0x00): MU_RPG_P_RAIL_DEV_SRH_SIC —>

<!— 4CF0F2 (0x4CF0F2 0x00): MU_RPG_P_RAIL_DEV_SRL_SIC —>

<!— 4CF0F2 (0x4CF0F2 0x00): MU_RPG_P_RAIL_DEV_SRL_SMC —>

<!— 4D0E03 (0x4D0E03 0x00): Injector Cylinder #3 Spill Control Valve Abnormal Operation (MAX) —>

<!— 4D0E03 (0x4D0E03 0x00): Injector Cylinder #3 Spill Control Valve («Amplifier»), Abnormal Operation (MAX) —>

<!— 4D0E04 (0x4D0E04 0x00): Injector Cylinder #3 Spill Control Valve Abnormal Operation (MIN) —>

<!— 4D0E04 (0x4D0E04 0x00): Injector Cylinder #3 Spill Control Valve («Amplifier»), Abnormal Operation (MIN) —>

<!— 4D0E05 (0x4D0E05 0x00): Injector Cylinder #3 Spill Control Valve («Amplifier»), Circuit Open —>

<!— 4D0E05 (0x4D0E05 0x00): MU_OFD_CYL3_PUMP_OPEN_LOAD —>

<!— 4D0E06 (0x4D0E06 0x00): «Injector Cylinder #3 Spill Control Valve («»Amplifier»»), Valve Shorted Circuit » —>

<!— 4D0E06 (0x4D0E06 0x00): Injector Cylinder #3 Spill Control Valve («Amplifier»), Valve Shorted Circuit —>

<!— 4D0E0A (0x4D0E0A 0x00): «Injector Cylinder #3 Spill Control Valve («»Amplifier»») Abnormal Rate of Change» —>

<!— 4D0E0A (0x4D0E0A 0x00): Injector Cylinder #3 Spill Control Valve («Amplifier») Abnormal Rate of Change —>

<!— 4D0E0A (0x4D0E0A 0x00): Injector Cylinder #3 Spill Control Valve («Amplifier»), Abnormal Rate of Change —>

<!— 4DF0E2 (0x4DF0E2 0x00): MU_RPG_INT_MON_SRL_SIC —>

<!— 4DF0E2 (0x4DF0E2 0x00): Over capacity in High Pressure Circuit, Similar Condition —>

<!— 4DF0EA (0x4DF0EA 0x00): MU_RPG_INT_MON_SRH_SIC —>

<!— 4DF0EA (0x4DF0EA 0x00): Under capacity in High Pressure Circuit, Similar Condition —>

<!— 4E0E03 (0x4E0E03 0x00): Injector Cylinder #4 Spill Control Valve Abnormal Operation (MAX) —>

<!— 4E0E03 (0x4E0E03 0x00): Injector Cylinder #4 Spill Control Valve («Amplifier»), Abnormal Operation (MAX) —>

<!— 4E0E04 (0x4E0E04 0x00): Injector Cylinder #4 Spill Control Valve Abnormal Operation (MIN) —>

<!— 4E0E04 (0x4E0E04 0x00): Injector Cylinder #4 Spill Control Valve («Amplifier»), Abnormal Operation (MIN) —>

<!— 4E0E05 (0x4E0E05 0x00): Injector Cylinder #4 Spill Control Valve («Amplifier»), Circuit Open —>

<!— 4E0E05 (0x4E0E05 0x00): MU_OFD_CYL4_PUMP_OPEN_LOAD —>

<!— 4E0E06 (0x4E0E06 0x00): «Injector Cylinder #4 Spill Control Valve («»Amplifier»»), Valve Shorted Circuit» —>

<!— 4E0E06 (0x4E0E06 0x00): Injector Cylinder #4 Spill Control Valve («Amplifier»), Valve Shorted Circuit —>

<!— 4E0E0A (0x4E0E0A 0x00): «Injector Cylinder #4 Spill Control Valve («»Amplifier»») Abnormal Rate of Change» —>

<!— 4E0E0A (0x4E0E0A 0x00): Injector Cylinder #4 Spill Control Valve («Amplifier») Abnormal Rate of Change —>

<!— 4E0E0A (0x4E0E0A 0x00): Injector Cylinder #4 Spill Control Valve («Amplifier»), Abnormal Rate of Change —>

<!— 4EF0E7 (0x4EF0E7 0x00): Classic Immobilizer, Key Slip Detected —>

<!— 4F0E03 (0x4F0E03 0x00): Injector Cylinder #5 Spill Control Valve Abnormal Operation (MAX) —>

<!— 4F0E03 (0x4F0E03 0x00): Injector Cylinder #5 Spill Control Valve («Amplifier»), Abnormal Operation (MAX) —>

<!— 4F0E04 (0x4F0E04 0x00): Injector Cylinder #5 Spill Control Valve Abnormal Operation (MIN) —>

<!— 4F0E04 (0x4F0E04 0x00): Injector Cylinder #5 Spill Control Valve («Amplifier»), Abnormal Operation (MIN) —>

<!— 4F0E05 (0x4F0E05 0x00): Injector Cylinder #5 Spill Control Valve («Amplifier»), Circuit Open —>

<!— 4F0E05 (0x4F0E05 0x00): MU_OFD_CYL5_PUMP_OPEN_LOAD —>

<!— 4F0E06 (0x4F0E06 0x00): «Injector Cylinder #5 Spill Control Valve («»Amplifier»»), Valve Shorted Circuit » —>

<!— 4F0E06 (0x4F0E06 0x00): Injector Cylinder #5 Spill Control Valve («Amplifier»), Valve Shorted Circuit —>

<!— 4F0E0A (0x4F0E0A 0x00): «Injector Cylinder #5 Spill Control Valve («»Amplifier»») Abnormal Rate of Change» —>

<!— 4F0E0A (0x4F0E0A 0x00): Injector Cylinder #5 Spill Control Valve («Amplifier») Abnormal Rate of Change —>

<!— 4F0E0A (0x4F0E0A 0x00): Injector Cylinder #5 Spill Control Valve («Amplifier»), Abnormal Rate of Change —>

<!— 4FF0EB (0x4FF0EB 0x00): Cylinder #1 Misfire Detected, Similar Condition —>

<!— 500E03 (0x500E03 0x00): Injector Cylinder #6 Spill Control Valve Abnormal Operation (MAX) —>

<!— 500E03 (0x500E03 0x00): Injector Cylinder #6 Spill Control Valve («Amplifier»), Abnormal Operation (MAX) —>

<!— 500E04 (0x500E04 0x00): Injector Cylinder #6 Spill Control Valve Abnormal Operation (MIN) —>

<!— 500E04 (0x500E04 0x00): Injector Cylinder #6 Spill Control Valve («Amplifier»), Abnormal Operation (MIN) —>

<!— 500E05 (0x500E05 0x00): Injector Cylinder #6 Spill Control Valve («Amplifier»), Circuit Open —>

<!— 500E05 (0x500E05 0x00): MU_OFD_CYL6_PUMP_OPEN_LOAD —>

<!— 500E06 (0x500E06 0x00): «Injector Cylinder #6 Spill Control Valve («»Amplifier»»), Valve Shorted Circuit» —>

<!— 500E06 (0x500E06 0x00): Injector Cylinder #6 Spill Control Valve («Amplifier»), Valve Shorted Circuit —>

<!— 500E0A (0x500E0A 0x00): «Injector Cylinder #6 Spill Control Valve («»Amplifier»») Abnormal Rate of Change» —>

<!— 500E0A (0x500E0A 0x00): Injector Cylinder #6 Spill Control Valve («Amplifier») Abnormal Rate of Change —>

<!— 500E0A (0x500E0A 0x00): Injector Cylinder #6 Spill Control Valve («Amplifier»), Abnormal Rate of Change —>

<!— 50F0EB (0x50F0EB 0x00): Cylinder #2 Misfire Detected, Similar Condition —>

<!— 510E0E (0x510E0E 0x00): FSG: MCM/ACM freeze frame version incompatible —>

<!— 510E0E (0x510E0E 0x00): MCM / ACM Freeze Frame Version Incompatible —>

<!— 510E0E (0x510E0E 0x00): MCM/ACM freeze frame version incompatible —>

<!— 51F0EB (0x51F0EB 0x00): Cylinder #3 Misfire Detected, Similar Condition —>

<!— 52F0EB (0x52F0EB 0x00): Cylinder #4 Misfire Detected, Similar Condition —>

<!— 53F0EB (0x53F0EB 0x00): Cylinder #5 Misfire Detected, Similar Condition —>

<!— 540002 (0x540002 0x00): J1939 Wheel-Based Vehicle Speed Signal from Source#1 is erratic —>

<!— 540002 (0x540002 0x00): J1939 Wheel-Based Vehicle Speed Signal from Source#1 is Erratic —>

<!— 540003 (0x540003 0x00): Vehicle Speed Sensor Circuit Failed High —>

<!— 540004 (0x540004 0x00): Vehicle Speed Sensor Circuit Failed Low —>

<!— 540009 (0x540009 0x00): J1939 Wheel-Based Vehicle Speed Signal from Source#2 is missing —>

<!— 540009 (0x540009 0x00): J1939 Wheel-Based Vehicle Speed Signal from Source#2 is Missing —>

<!— 54000A (0x54000A 0x00): J1939 Wheel-Based Vehicle Speed Signal from Source#3 is erratic —>

<!— 54000A (0x54000A 0x00): J1939 Wheel-Based Vehicle Speed Signal from Source#3 is Erratic —>

<!— 54000B (0x54000B 0x00): Vehicle Speed Failure —>

<!— 54000D (0x54000D 0x00): J1939 Wheel-Based Vehicle Speed Signal from Source#1 is missing —>

<!— 54000D (0x54000D 0x00): J1939 Wheel-Based Vehicle Speed Signal from Source#1 is Missing —>

<!— 54000E (0x54000E 0x00): J1939 Wheel-Based Vehicle Speed Signal from Source#3 is missing —>

<!— 54000E (0x54000E 0x00): J1939 Wheel-Based Vehicle Speed Signal from Source#3 is Missing —>

<!— 540013 (0x540013 0x00): J1939 Wheel-Based Vehicle Speed Signal from Source#2 is erratic —>

<!— 540013 (0x540013 0x00): J1939 Wheel-Based Vehicle Speed Signal from Source#2 is Erratic —>

<!— 540015 (0x540015 0x00): MU_RC4_VSS_DATA_ERRATIC —>

<!— 540015 (0x540015 0x00): Vehicle Speed Sensor Erratic —>

<!— 54F0EB (0x54F0EB 0x00): Cylinder #6 Misfire Detected, Similar Condition —>

<!— 55F0EE (0x55F0EE 0x00): Misfire Detection without Cylinder Number Detection, Similar Condition —>

<!— 56F0EE (0x56F0EE 0x00): Multiple Cylinder Misfire Detected, Similar Condition —>

<!— 57F0E7 (0x57F0E7 0x00): Starter Inhibit due to SCM —>

<!— 580403 (0x580403 0x00): MDEG Brake System (Two Stage Brake), Circuit Failed High —>

<!— 580404 (0x580404 0x00): MDEG Brake System (Two Stage Brake), Circuit Failed Low —>

<!— 580405 (0x580405 0x00): MDEG Brake System (Two Stage Brake), Circuit Failed Open —>

<!— 58F0E7 (0x58F0E7 0x00): Engine Brake Inhibit due to SCM via MVB —>

<!— 59F0E7 (0x59F0E7 0x00): Engine Brake Inhibit due to SCM via JB1 —>

<!— 5AF0E7 (0x5AF0E7 0x00): Engine Brake Inhibit due to SCM via JB2 —>

<!— 5BF0E2 (0x5BF0E2 0x00): EGR Pipe Frozen —>

<!— 5CF0E2 (0x5CF0E2 0x00): EGR Valve Frozen —>

<!— 5CF0E2 (0x5CF0E2 0x00): EGR Valve frozen —>

<!— 5DF0E2 (0x5DF0E2 0x00): Slow Engine Oil Pressure Buildup, Reduced Engine Torque —>

<!— 5DF0E2 (0x5DF0E2 0x00): Slow engine oil pressure buildup, reduced engine torque —>

<!— 5E0001 (0x5E0001 0x00): Fuel Pressure in Low Pressure Circuit too Low —>

<!— 5E0001 (0x5E0001 0x00): MU_IS2_P_LOW_CIRC_TOO_LOW —>

<!— 5E0002 (0x5E0002 0x00): Low Side Fuel Pressure Not Plausible —>

<!— 5E0003 (0x5E0003 0x00): Low Side Fuel Pressure Sensor Circuit Failed High —>

<!— 5E0004 (0x5E0004 0x00): Low Side Fuel Pressure Sensor Circuit Failed Low —>

<!— 5E000F (0x5E000F 0x00): Fuel Filter Service Warning —>

<!— 5E0010 (0x5E0010 0x00): Fuel Filter Replacement Required —>

<!— 5E040F (0x5E040F 0x00): EGR Flow Rate too Low —>

<!— 5E0410 (0x5E0410 0x00): EGR Flow Rate too Low —>

<!— 5E0410 (0x5E0410 0x00): FSG: EGR Flow Rate too Low —>

<!— 5E0410 (0x5E0410 0x00): MU_RC4_EGR_DEV_LOW_LEV2 —>

<!— 5E0412 (0x5E0412 0x00): EGR Flow Rate too High —>

<!— 5E0412 (0x5E0412 0x00): FSG: EGR Flow Rate too High —>

<!— 5EF0E7 (0x5EF0E7 0x00): MU_SCM_RESET_HW_DEFECT —>

<!— 5EF0EE (0x5EF0EE 0x00): MU_SCM_RESET_SW_DEFECT —>

<!— 5EF0FF (0x5EF0FF 0x00): SW-Reset Executed by MCM2-Level3 Monitoring due to Microcontroller / OS Issue or Request by Level2-Monitoring —>

<!— 5FF0E2 (0x5FF0E2 0x00): Oil Level Sensor Value Not Plausible —>

<!— 5FF0E7 (0x5FF0E7 0x00): MU_SCM_RESET_HW_DEFECT —>

<!— 5FF0ED (0x5FF0ED 0x00): MU_SCM_RESET_SW_DEFECT —>

<!— 5FF0EE (0x5FF0EE 0x00): MU_SCM_INACT_BY_MISSNG_VIN —>

<!— 600002 (0x600002 0x00): fuel sender signal not plausible —>

<!— 600002 (0x600002 0x00): Fuel Tank Level Sensor Stuck in Position —>

<!— 600002 (0x600002 0x00): MU_IS4_CAN_LVL_FEUL_TNK_PLAUS —>

<!— 601003 (0x601003 0x00): Water Level Electrical Water Separator SRC Failed High —>

<!— 601004 (0x601004 0x00): Water Level Electrical Water Separator SRC Failed Low —>

<!— 601007 (0x601007 0x00): Electrical Water Separator, Mechanical Defect —>

<!— 601009 (0x601009 0x00): Engine Fuel Filter Water Level Sensor Circuit Failed High —>

<!— 60100E (0x60100E 0x00): Electrical Water Separator, Valve defect —>

<!— 60100E (0x60100E 0x00): Electrical Water Separator, Valve Defect —>

<!— 60100F (0x60100F 0x00): Filter Lifetime Pre Warning —>

<!— 60100F (0x60100F 0x00): FSG: Filter lifetime pre-warning —>

<!— 60100F (0x60100F 0x00): FSG: Water seperator lifetime pre-warning —>

<!— 601010 (0x601010 0x00): Filter Lifetime Warning —>

<!— 601010 (0x601010 0x00): FSG: Filter lifetime warning —>

<!— 601010 (0x601010 0x00): FSG: Water seperator lifetime warning —>

<!— 60F0EE (0x60F0EE 0x00): MU_FMM_TEST1 —>

<!— 60F0FF (0x60F0FF 0x00): MU_FMM_TEST2 —>

<!— 610000 (0x610000 0x00): Water in Fuel Lifetime exceeded —>

<!— 610000 (0x610000 0x00): Water in Fuel Lifetime Exceeded —>

<!— 610003 (0x610003 0x00): Water in Fuel Circuit Failed High —>

<!— 610004 (0x610004 0x00): Water in Fuel Circuit Failed Low —>

<!— 610007 (0x610007 0x00): MU_ISP_WIF_DEFECTIVE —>

<!— 610007 (0x610007 0x00): Water in Fuel Sensor — Defect —>

<!— 61000E (0x61000E 0x00): MU_ISP_WATER_IN_FUEL_IGNRD —>

<!— 61000E (0x61000E 0x00): water in fuel drain request light ignored —>

<!— 61000E (0x61000E 0x00): Water in Fuel Ignored — Warning —>

<!— 61000F (0x61000F 0x00): Water in Fuel —>

<!— 610010 (0x610010 0x00): MU_ISP_WATER_IN_FUEL2 —>

<!— 610010 (0x610010 0x00): Water in Fuel Ignored — Derate —>

<!— 61001F (0x61001F 0x00): MU_ISP_WATER_IN_FUEL_IGNR2 —>

<!— 61001F (0x61001F 0x00): Water in Fuel Ignored — Shutdown —>

<!— 61020C (0x61020C 0x00): FSG: SW-Reset executed by MCM2-Level3 monitoring due to mikrocontroller / OS issue or request by Level2-monitoring —>

<!— 61020C (0x61020C 0x00): Microcontroller Trap has been activated —>

<!— 61020C (0x61020C 0x00): SW-Reset Executed by MCM2-Level3 Monitoring due to Microcontroller / OS Issue or Request by Level2-Monitoring —>

<!— 61020C (0x61020C 0x00): SW-Reset executed by MCM2-Level3 monitoring due to mikrocontroller / OS issue or request by Level2-monitoring: —>

<!— 611002 (0x611002 0x00): Coolant Inlet Temperature Not Plausible —>

<!— 611003 (0x611003 0x00): Engine Coolant Inlet Temperature Circuit Failed High —>

<!— 611004 (0x611004 0x00): Engine Coolant Inlet Temperature Circuit Failed Low —>

<!— 61100A (0x61100A 0x00): Coolant Temperature Sensors not Plausible —>

<!— 61100A (0x61100A 0x00): Coolant Temperature Sensors Not Plausible —>

<!— 611011 (0x611011 0x00): MU_ISP_ENG_WARM_MON —>

<!— 611015 (0x611015 0x00): MU_RC4_T_COOLANT_IN_GEN2 —>

<!— 61101F (0x61101F 0x00): Engine Coolant Sensor (IN), General Temp. Plausibility Error —>

<!— 61101F (0x61101F 0x00): Engine Coolant Sensor (IN), General Temperature Plausibility Error —>

<!— 61F0EE (0x61F0EE 0x00): MU_EBM_BRK_FAIL_CYL1 —>

<!— 620000 (0x620000 0x00): Oil Level Circuit Failed High —>

<!— 620001 (0x620001 0x00): Oil Level Circuit Failed Low —>

<!— 620002 (0x620002 0x00): FSG: Oil level sensor value not plausible —>

<!— 620002 (0x620002 0x00): Oil Level Sensor Value Not Plausible —>

<!— 620004 (0x620004 0x00): FSG: Oil Level Sensor defect —>

<!— 620004 (0x620004 0x00): MU_ISP_L_OIL_DEF —>

<!— 620004 (0x620004 0x00): Oil Level Sensor Defect —>

<!— 620005 (0x620005 0x00): FSG: Oil Level Sensor Wire Open Load —>

<!— 620005 (0x620005 0x00): Oil Level Sensor Wire Open Load —>

<!— 620005 (0x620005 0x00): tbd —>

<!— 62000D (0x62000D 0x00): Oil Level Measurement, Configuration Error —>

<!— 62000D (0x62000D 0x00): Oil Level Mesaurement, Configuration Error —>

<!— 62000E (0x62000E 0x00): MU_FAB_OIL_LEV_MEAS_PEND —>

<!— 62000E (0x62000E 0x00): Oil Level Mesaurement, Oil Level Too Low or Too High —>

<!— 62000E (0x62000E 0x00): Oil Level Mesaurement, Oil Level too Low or too High —>

<!— 620010 (0x620010 0x00): Engine Oil Level too High —>

<!— 620010 (0x620010 0x00): FSG: Engine Oil Level Too High —>

<!— 620011 (0x620011 0x00): Engine Oil Level is too Low —>

<!— 620012 (0x620012 0x00): Engine Oil Level too Low —>

<!— 620012 (0x620012 0x00): FSG: Engine Oil Level too low —>

<!— 620103 (0x620103 0x00): Relative Humidity Circuit Failed High —>

<!— 620104 (0x620104 0x00): Relative Humidity Circuit Failed Low —>

<!— 62F0EE (0x62F0EE 0x00): MU_EBM_BRK_FAIL_CYL2 —>

<!— 630A00 (0x630A00 0x00): EGR Flow Target Error Diagnostic — High Flow —>

<!— 630A0A (0x630A0A 0x00): MU_AM_EGR_SLOW_RESPONSE —>

<!— 630A12 (0x630A12 0x00): EGR Flow Target Error Diagnostic — Low Flow —>

<!— 63F0EE (0x63F0EE 0x00): MU_EBM_BRK_FAIL_CYL3 —>

<!— 640000 (0x640000 0x00): MU_RC1_P_OIL_STUCK —>

<!— 640001 (0x640001 0x00): Engine Oil Pressure Low —>

<!— 640002 (0x640002 0x00): Oil Pressure Plausibility — Engine Running —>

<!— 640002 (0x640002 0x00): Slow Engine Oil Pressure Buildup, Reduced Engine Torque —>

<!— 640003 (0x640003 0x00): Engine Oil Pressure Circuit Failed High —>

<!— 640004 (0x640004 0x00): Engine Oil Pressure Circuit Failed Low —>

<!— 64000A (0x64000A 0x00): MU_EPF_P_ENG_OIL_BUILDUP —>

<!— 640010 (0x640010 0x00): MU_EPF_P_ENG_OIL_HIGH_WARN —>

<!— 640011 (0x640011 0x00): MU_EPF_P_ENG_OIL_PREWARN —>

<!— 640012 (0x640012 0x00): MU_EPF_LOW_IDLE_SHUT_DOWN —>

<!— 640014 (0x640014 0x00): Oil Pressure Plausibility — Stop —>

<!— 640600 (0x640600 0x00): Charge Air Cooler Low Efficiency —>

<!— 640602 (0x640602 0x00): Difference Intake Manifold and I Cooler Temperature Out Less Than Threshold (Low Box) —>

<!— 640602 (0x640602 0x00): Difference Intake Manifold and Icooler Temperature Out Less Than Threshold (Low Box) —>

<!— 640603 (0x640603 0x00): Intake Manifold Temperature Circuit Failed High —>

<!— 640604 (0x640604 0x00): Intake Manifold Temperature Circuit Failed Low —>

<!— 64060B (0x64060B 0x00): Intake Manifold Temperature Plausibility Error —>

<!— 640614 (0x640614 0x00): Intake Manifold Temperature Drift (Low Box) —>

<!— 640615 (0x640615 0x00): Intake Manifold Temperature Drift (High Box) —>

<!— 64F0EE (0x64F0EE 0x00): MU_EBM_BRK_FAIL_CYL4 —>

<!— 65F0EE (0x65F0EE 0x00): MU_EBM_BRK_FAIL_CYL5 —>

<!— 660010 (0x660010 0x00): FSG: Intake Manifold Pressure to high —>

<!— 660010 (0x660010 0x00): Intake Manifold Pressure too High —>

<!— 660012 (0x660012 0x00): Intake Manifold Pressure to Low —>

<!— 660012 (0x660012 0x00): Intake Manifold Pressure too Low —>

<!— 66F0EE (0x66F0EE 0x00): MU_EBM_BRK_FAIL_CYL6 —>

<!— 670000 (0x670000 0x00): Turbo Charger Speed Above Threshold (Low Box) —>

<!— 670001 (0x670001 0x00): Turbo Charger Speed Below Threshold (High Box) —>

<!— 670002 (0x670002 0x00): Turbo Charger Speed Not Plausible —>

<!— 670002 (0x670002 0x00): Turbocharger Speed Not Plausible —>

<!— 670003 (0x670003 0x00): Turbo Charger Speed Sensor Circuit Failed High —>

<!— 670004 (0x670004 0x00): Turbo Charger Speed Sensor Circuit Failed Low —>

<!— 67000F (0x67000F 0x00): Turbo Charger Overspeed Check —>

<!— 670010 (0x670010 0x00): MU_RC4_TC_OVRSPD_DET —>

<!— 670202 (0x670202 0x00): Water Pump Limp Home Mode —>

<!— 670207 (0x670207 0x00): Water Pump Mechanical Defect Detected —>

<!— 670213 (0x670213 0x00): Smart Actuator Indicates Actuator Position Error —>

<!— 67040A (0x67040A 0x00): FSG: Turbocharger Boost Control «A» Slow Response —>

<!— 67040A (0x67040A 0x00): MU_RC4_BST_SLOW_RESPONSE —>

<!— 67040A (0x67040A 0x00): Turbo Charger Boost Control «A» Slow Response —>

<!— 670601 (0x670601 0x00): FAN Clutch Issue —>

<!— 670602 (0x670602 0x00): Fan Speed Error —>

<!— 670602 (0x670602 0x00): FSG: Fan speed error —>

<!— 670610 (0x670610 0x00): MU_FAN_ENG_RATE_HIGH_ERR —>

<!— 670612 (0x670612 0x00): MU_FAN_ENG_RATE_LOW_ERR —>

<!— 67F0EB (0x67F0EB 0x00): Smart Remote Actuator 1 (Wastegate), Temperature Fault —>

<!— 67F0EB (0x67F0EB 0x00): Smart Remote Actuator 1 (Wastegate), Learn Span Too Small Range 2, Max Learn Attempts Completed —>

<!— 67F0EC (0x67F0EC 0x00): Smart Remote Actuator 1 (Wastegate), Internal Test Running —>

<!— 67F0EC (0x67F0EC 0x00): Smart Remote Actuator 1 (Wastegate), Learn Span Too Small Range 2, Max Learn Attempts Not Completed —>

<!— 67F0EE (0x67F0EE 0x00): MU_AM_SRA1_LEARN_R3_SEAT —>

<!— 67F0EE (0x67F0EE 0x00): Smart Remote Actuator 1 (Wastegate), Learn Span Too Small Range 3 —>

<!— 67F0F3 (0x67F0F3 0x00): Smart Remote Actuator 1 (Wastegate), Temperature Warning —>

<!— 67F0F3 (0x67F0F3 0x00): Smart Remote Actuator 1 (Wastegate), Communication Error —>

<!— 67F0FF (0x67F0FF 0x00): Smart Remote Actuator 1 (Wastegate), Restricted Operability —>

<!— 67F0FF (0x67F0FF 0x00): Smart Remote Actuator 1 (Wastegate), Learn Cycle Incomplete —>

<!— 68F0E3 (0x68F0E3 0x00): EGR Valve Actuator, Low Supply Voltage —>

<!— 68F0E3 (0x68F0E3 0x00): MU_AM_SRA3_SUPPLY_ERR —>

<!— 68F0E3 (0x68F0E3 0x00): Smart Remote Actuator 3 (EGR), Low Supply Voltage —>

<!— 68F0ED (0x68F0ED 0x00): EGR Valve Actuator, Error —>

<!— 68F0ED (0x68F0ED 0x00): EGR Valve Actuator, Unknown Error Code —>

<!— 68F0ED (0x68F0ED 0x00): Smart Remote Actuator 3 (EGR), Calibration Error —>

<!— 68F0EE (0x68F0EE 0x00): MU_AM_SRA3_BUFFER_1 —>

<!— 68F0EE (0x68F0EE 0x00): Smart Remote Actuator 3 (EGR), Place Holder MU_1 —>

<!— 68F0F3 (0x68F0F3 0x00): EGR Valve Actuator, Communication Error —>

<!— 68F0F3 (0x68F0F3 0x00): EGR Valve Actuator, Internal Test Running —>

<!— 68F0F3 (0x68F0F3 0x00): Smart Remote Actuator 3 (EGR), Communication Error —>

<!— 68F0FF (0x68F0FF 0x00): EGR Valve Actuator, Learn Cycle Incomplete —>

<!— 68F0FF (0x68F0FF 0x00): EGR Valve Actuator, Temperature Warning —>

<!— 68F0FF (0x68F0FF 0x00): Smart Remote Actuator 3 (EGR), Learn Cycle Incomplete —>

<!— 690002 (0x690002 0x00): MU_RC4_T_INTAKE_GEN2 —>

<!— 690010 (0x690010 0x00): Cooling Efficency of Icooler too Low —>

<!— 690010 (0x690010 0x00): Cooling Efficency of intercooler to low —>

<!— 690010 (0x690010 0x00): FSG: Cooling Efficency of intercooler to low —>

<!— 69F0EE (0x69F0EE 0x00): MU_AM_SRA3_BUFFER_2 —>

<!— 69F0EE (0x69F0EE 0x00): Smart Remote Actuator 3 (EGR), Place Holder MU_2 —>

<!— 6AF0EE (0x6AF0EE 0x00): MU_AM_SRA1_BUFFER_1 —>

<!— 6AF0EE (0x6AF0EE 0x00): Smart Remote Actuator 1 (Wastegate), Place Holder MU_1 —>

<!— 6BF0EE (0x6BF0EE 0x00): MU_AM_SRA1_BUFFER_2 —>

<!— 6BF0EE (0x6BF0EE 0x00): Smart Remote Actuator 1 (Wastegate), Place Holder MU_2 —>

<!— 6C0002 (0x6C0002 0x00): tbd —>

<!— 6C0003 (0x6C0003 0x00): Barometric Pressure Circuit Failed High —>

<!— 6C0004 (0x6C0004 0x00): Barometric Pressure Circuit Failed Low —>

<!— 6C0014 (0x6C0014 0x00): tbd —>

<!— 6C0303 (0x6C0303 0x00): Air Compressor Clutch, Circuit Failed High —>

<!— 6C0304 (0x6C0304 0x00): Air Compressor Clutch, Circuit Failed Low —>

<!— 6C0305 (0x6C0305 0x00): Air Compressor Clutch, Circuit Failed Open —>

<!— 6CF0E3 (0x6CF0E3 0x00): MU_CMP_PVH_WAX_SC_BATT —>

<!— 6CF0E4 (0x6CF0E4 0x00): MU_CMP_PVH_WAX_SC_GND —>

<!— 6CF0E5 (0x6CF0E5 0x00): MU_CMP_PVH_WAX_OL —>

<!— 6DF0EF (0x6DF0EF 0x00): MU_EPF_STARTER_MAX_COUNT —>

<!— 6E0000 (0x6E0000 0x00): Coolant Temperature High —>

<!— 6E0001 (0x6E0001 0x00): MU_EPF_IDLE_T_COOL_L_WARN —>

<!— 6E0002 (0x6E0002 0x00): Coolant Outlet Temperature Not Plausible —>

<!— 6E0003 (0x6E0003 0x00): Engine Coolant Outlet Temperature Circuit Failed High —>

<!— 6E0004 (0x6E0004 0x00): Engine Coolant Outlet Temperature Circuit Failed Low —>

<!— 6E000E (0x6E000E 0x00): Coolant Temperature / Engine Oil Temperature Plausibility Fault —>

<!— 6E000F (0x6E000F 0x00): MU_EPF_T_COOL_HIGH_PREWARN —>

<!— 6E0012 (0x6E0012 0x00): MU_RC4_COOL_SYS_FAIL —>

<!— 6E0014 (0x6E0014 0x00): Engine Coolant Sensor (OUT), General Temp. Plausibility Error —>

<!— 6E0014 (0x6E0014 0x00): Engine Coolant Sensor (OUT), General Temperature Plausibility Error —>

<!— 6E0015 (0x6E0015 0x00): MU_RC4_T_COOLANT_OUT_GEN2 —>

<!— 6E001F (0x6E001F 0x00): Coolant Temperature Differential High —>

<!— 6EF0E2 (0x6EF0E2 0x00): MU_RC4_LAMBDA_DEV_NOX —>

<!— 6F0001 (0x6F0001 0x00): Coolant Level Very Low —>

<!— 6F0003 (0x6F0003 0x00): Coolant Level Circuit Failed High —>

<!— 6F0004 (0x6F0004 0x00): Coolant Level Circuit Failed Low —>

<!— 6F0012 (0x6F0012 0x00): Coolant Level Low —>

<!— 6F0013 (0x6F0013 0x00): Coolant Level Low (CAN) —>

<!— 6F0200 (0x6F0200 0x00): Driver Inducement System, SEL Solid Active —>

<!— 6F0210 (0x6F0210 0x00): Driver Inducement System, SEL Flash Active —>

<!— 6FF0EE (0x6FF0EE 0x00): MU_RC4_LAMBDA_DEV_AFL —>

<!— 700200 (0x700200 0x00): Driver Inducement System, CEL Solid Active —>

<!— 700210 (0x700210 0x00): Driver Inducement System, CEL Flash Active —>

<!— 70F0EF (0x70F0EF 0x00): MU_SP_EGR_MASS_VIRT_OFFSET —>

<!— 710202 (0x710202 0x00): Invalid Data on Engine CAN Link —>

<!— 710203 (0x710203 0x00): Engine CAN High Wire Defect — (wire 2) —>

<!— 710203 (0x710203 0x00): Engine CAN High Wire Defect — (Wire 2) —>

<!— 710204 (0x710204 0x00): Engine CAN Low Wire Defect — (wire 1) —>

<!— 710204 (0x710204 0x00): Engine CAN Low Wire Defect — (Wire 1) —>

<!— 710208 (0x710208 0x00): MCM UDS DM1 Message Not Received or has Stopped Arriving —>

<!— 710209 (0x710209 0x00): No Data Received from Engine CAN Link —>

<!— 71020E (0x71020E 0x00): ACM UDS DM1 Message Not Received or has Stopped Arriving —>

<!— 710211 (0x710211 0x00): MU_CAN_NO_COM_STAGE2 —>

<!— 710211 (0x710211 0x00): No ACM Communication — Pre Warning —>

<!— 710212 (0x710212 0x00): MU_CAN_NO_COM_STAGE3 —>

<!— 710212 (0x710212 0x00): No ACM Communication — Warning —>

<!— 74020D (0x74020D 0x00): MCM Powerdown Error —>

<!— 760202 (0x760202 0x00): Calibration Data Not Plausible —>

<!— 76020A (0x76020A 0x00): MU_STU_NO_PWL —>

<!— 76020C (0x76020C 0x00): EEPROM Read / Write Operation Failed —>

<!— 76020D (0x76020D 0x00): Calibration Data Not Plausible (CPLD) —>

<!— 76020E (0x76020E 0x00): UDS Tables unsorted, UDS security access issue —>

<!— 76020E (0x76020E 0x00): UDS Tables Unsorted, UDS Security Access Issue —>

<!— 76021F (0x76021F 0x00): MU_E2P_IR_DATA_LOSS —>

<!— 760E0D (0x760E0D 0x00): FSG: HC-Dosing Conditions not fullfilled —>

<!— 760E0D (0x760E0D 0x00): HC-Dosing Conditions Not Fullfilled —>

<!— 760E0D (0x760E0D 0x00): tbd —>

<!— 7B0601 (0x7B0601 0x00): MU_RC4_TSTAT_MON —>

<!— 7B0611 (0x7B0611 0x00): MU_ISP_TSTAT_MON —>

<!— 7B0612 (0x7B0612 0x00): Thermostat Error Detected —>

<!— 7C0201 (0x7C0201 0x00): Crankshaft Position Sensor Short to Ground —>

<!— 7C0201 (0x7C0201 0x00): Crankshaft Position Sensor Signal Voltage Too Low —>

<!— 7C0202 (0x7C0202 0x00): No Match of Camshaft and Crankshaft Signals —>

<!— 7C0203 (0x7C0203 0x00): Crankshaft Position Sensor Open Circuit —>

<!— 7C0204 (0x7C0204 0x00): Crankshaft Position Sensor Short to Ground —>

<!— 7C0204 (0x7C0204 0x00): Crankshaft Position Sensor Signal Voltage Too Low —>

<!— 7C0204 (0x7C0204 0x00): Crankshaft Position Sensor Signal Voltage too Low —>

<!— 7C0208 (0x7C0208 0x00): Crankshaft Position Sensor Time Out —>

<!— 7C020A (0x7C020A 0x00): Crankshaft Position Sensor Signal Erratic —>

<!— 7C020B (0x7C020B 0x00): Crankshaft Position Sensor Failure —>

<!— 7C020E (0x7C020E 0x00): Crankshaft Position Sensor Pins Swapped —>

<!— 7C020F (0x7C020F 0x00): Phase Shift of CRK Tooth 97 to CAM Tooth 10 is too High (Crankshaft Position — Camshaft Position Correlation) —>

<!— 7E1400 (0x7E1400 0x00): MU_OBD_INDC_FLT_FNL_ACT —>

<!— 7E140E (0x7E140E 0x00): Tier4 Inducement System Has Not Been Activated —>

<!— 7E140F (0x7E140F 0x00): MU_OBD_INDC_FLT_FNL_WRNG —>

<!— 7E1410 (0x7E1410 0x00): MU_OBD_INDC_FLT_DERATE —>

<!— 7E141F (0x7E141F 0x00): MU_OBD_INDC_FNL_SHTDWN_ACT —>

<!— 7F020E (0x7F020E 0x00): J1939 Data Link Failure —>

<!— 810203 (0x810203 0x00): Turbo Control Circuit Failed High —>

<!— 810204 (0x810204 0x00): Turbo Control Circuit Failed Low —>

<!— 810205 (0x810205 0x00): Turbo Control Circuit Open —>

<!— 821003 (0x821003 0x00): Differential pressure icooler out sensor circuit failed High —>

<!— 821003 (0x821003 0x00): Differential Pressure Icooler Out Sensor Circuit Failed High —>

<!— 821003 (0x821003 0x00): Differential pressure icooler out sensor circuit failed high —>

<!— 821003 (0x821003 0x00): FSG: Differential pressure icooler out sensor circuit failed low —>

<!— 821004 (0x821004 0x00): Differential pressure icooler out sensor circuit failed Low —>

<!— 821004 (0x821004 0x00): Differential Pressure Icooler Out Sensor Circuit Failed Low —>

<!— 821004 (0x821004 0x00): Differential pressure icooler out sensor circuit failed low —>

<!— 821004 (0x821004 0x00): FSG: Differential pressure icooler out sensor circuit failed low —>

<!— 82100D (0x82100D 0x00): FSG: Icooler out differential pressure sensor out of calibration low —>

<!— 82100D (0x82100D 0x00): Icooler Out Differential Pressure Sensor Out of Calibration Low —>

<!— 82100D (0x82100D 0x00): Icooler out differential pressure sensor out of calibration low —>

<!— 82100E (0x82100E 0x00): FSG: Icooler out differential pressure sensor out of calibration high —>

<!— 82100E (0x82100E 0x00): Icooler Out Differential Pressure Sensor Out of Calibration High —>

<!— 82100E (0x82100E 0x00): Icooler out differential pressure sensor out of calibration high —>

<!— 821014 (0x821014 0x00): FSG: Icooler out differential pressure plausibility fault, pressure to high (low box) —>

<!— 821014 (0x821014 0x00): Icooler Out Differential Pressure Plausibility Fault, Pressure too High (Low Box) —>

<!— 821014 (0x821014 0x00): Icooler out differential pressure plausibility fault, pressure to high (low box) —>

<!— 821015 (0x821015 0x00): FSG: Icooler out differential pressure plausibility fault, pressure too low (high box) —>

<!— 821015 (0x821015 0x00): Icooler Out Differential Pressure Plausibility Fault, Pressure too Low (High Box) —>

<!— 821015 (0x821015 0x00): Icooler out differential pressure plausibility fault, pressure too low (high box) —>

<!— 831003 (0x831003 0x00): Electrostatic Oil Separator Circuit Failed High —>

<!— 831004 (0x831004 0x00): Electrostatic Oil Separator Circuit Failed Low —>

<!— 831005 (0x831005 0x00): Electrostatic Oil Separator Circuit Failed Open —>

<!— 831007 (0x831007 0x00): Oil Separator, Max. Duration Time Reached —>

<!— 840001 (0x840001 0x00): Air Mass Flow Too Low —>

<!— 840001 (0x840001 0x00): Air Mass Flow too Low —>

<!— 840002 (0x840002 0x00): Air Mass Adaption Reached Limit —>

<!— 840002 (0x840002 0x00): Air Mass Freeze Detection —>

<!— 840002 (0x840002 0x00): FSG: Air mass adaption reached limit —>

<!— 84000D (0x84000D 0x00): Air Mass Auto Calibration Failed —>

<!— 84000F (0x84000F 0x00): Air Mass Adaption has Reached Implausible Value —>

<!— 840E1F (0x840E1F 0x00): High Idle Regeneration — Low Temperature —>

<!— 840E1F (0x840E1F 0x00): MU_DPF_HIR_TM_MODE_ERR —>

<!— 850510 (0x850510 0x00): FSG: Injection Timing Cyl# 1 Out of range —>

<!— 850510 (0x850510 0x00): Injection Timing Cylinder #1 Out of Range —>

<!— 85051F (0x85051F 0x00): End of injection Timing Cylinder #1 Out of Range —>

<!— 85051F (0x85051F 0x00): FSG: End of injection timing cylinder #1 out of range —>

<!— 860510 (0x860510 0x00): FSG: Injection Timing Cyl# 2 Out of range —>

<!— 860510 (0x860510 0x00): Injection Timing Cylinder #2 Out of Range —>

<!— 86051F (0x86051F 0x00): End of Injection Timing Cylinder #2 Out of Range —>

<!— 86051F (0x86051F 0x00): FSG: End of injection timing cylinder #2 out of range —>

<!— 870203 (0x870203 0x00): Fan Stage 1 Circuit Failed High —>

<!— 870204 (0x870204 0x00): Fan Stage 1 Circuit Failed Low —>

<!— 870205 (0x870205 0x00): Fan Stage 1 Circuit Failed Open —>

<!— 870510 (0x870510 0x00): FSG: Injection Timing Cyl# 3 Out of range —>

<!— 870510 (0x870510 0x00): Injection Timing Cylinder #3 Out of Range —>

<!— 87051F (0x87051F 0x00): End of Injection Timing Cylinder #3 Out of Range —>

<!— 87051F (0x87051F 0x00): FSG: End of injection timing cylinder #3 out of range —>

<!— 880510 (0x880510 0x00): FSG: Injection Timing Cyl# 4 Out of range —>

<!— 880510 (0x880510 0x00): Injection Timing Cylinder #4 Out of Range —>

<!— 88051F (0x88051F 0x00): End of Injection Timing Cylinder #4 Out of Range —>

<!— 88051F (0x88051F 0x00): FSG: End of injection timing cylinder #4 out of range —>

<!— 880D02 (0x880D02 0x00): Intake Throttle Valve, Spring Response Time Not Plausible —>

<!— 880D03 (0x880D03 0x00): FSG: H Bridge 1 IAT Circiut Shorted to Battery —>

<!— 880D03 (0x880D03 0x00): H Bridge 1 IAT Circiut Shorted to Battery —>

<!— 880D04 (0x880D04 0x00): FSG: H Bridge 1 IAT Circuit Shorted to Ground —>

<!— 880D04 (0x880D04 0x00): H Bridge 1 IAT Circuit Shorted to Ground —>

<!— 880D05 (0x880D05 0x00): FSG: H Bridge 1 IAT Short Circuit/Over Current —>

<!— 880D05 (0x880D05 0x00): H Bridge 1 Circuit Shorted Load —>

<!— 880D05 (0x880D05 0x00): H Bridge 1 IAT Short Circuit / Over Current —>

<!— 880D07 (0x880D07 0x00): Intake Throttle Valve, Stuck —>

<!— 880D08 (0x880D08 0x00): Intake Throttle Valve, Current Deviation Too High —>

<!— 880D08 (0x880D08 0x00): Intake Throttle Valve, Current Deviation too High —>

<!— 880D0E (0x880D0E 0x00): Intake Throttle Valve, Integrated Absolute Error Plausibility —>

<!— 880D10 (0x880D10 0x00): MU_RC4_ITV_P_INT_DEV_HIGH —>

<!— 880D11 (0x880D11 0x00): MU_CAC_ITV_PLAUS_ERR —>

<!— 880D12 (0x880D12 0x00): MU_RC4_ITV_P_INT_DEV_LOW —>

<!— 880D1F (0x880D1F 0x00): FSG: H Bridge 1 IAT circuit open load —>

<!— 880D1F (0x880D1F 0x00): H Bridge 1 Circuit Open Load —>

<!— 880D1F (0x880D1F 0x00): H Bridge 1 IAT Circuit Open Load —>

<!— 890510 (0x890510 0x00): FSG: Injection Timing Cyl# 5 Out of range —>

<!— 890510 (0x890510 0x00): Injection Timing Cylinder #5 Out of Range —>

<!— 89051F (0x89051F 0x00): End of Injection Timing Cylinder #5 Out of Range —>

<!— 89051F (0x89051F 0x00): FSG: End of injection timing cylinder #5 out of range —>

<!— 8A0510 (0x8A0510 0x00): FSG: Injection Timing Cyl# 6 Out of range —>

<!— 8A0510 (0x8A0510 0x00): Injection Timing Cylinder #6 Out of Range —>

<!— 8A051F (0x8A051F 0x00): End of Injection Timing Cylinder #6 Out of Range —>

<!— 8A051F (0x8A051F 0x00): FSG: End of injection timing cylinder #6 out of range —>

<!— 8B0203 (0x8B0203 0x00): Injector Cylinder #1 Needle Control Valve Abnormal Operation (MAX) —>

<!— 8B0203 (0x8B0203 0x00): Injector Cylinder #1 Needle Control Valve, Abnormal Operation (MAX) —>

<!— 8B0204 (0x8B0204 0x00): Injector Cylinder #1 Needle Control Valve Abnormal Operation (MIN) —>

<!— 8B0204 (0x8B0204 0x00): Injector Cylinder #1 Needle Control Valve, Abnormal Operation (MIN) —>

<!— 8B0205 (0x8B0205 0x00): Injector Cylinder #1, Needle Control Valve Circuit Open —>

<!— 8B0205 (0x8B0205 0x00): MU_OFD_CYL1_INJ_OPEN_LOAD —>

<!— 8B0206 (0x8B0206 0x00): Injector Cylinder #1 Needle Control Valve, Valve Shorted Circuit —>

<!— 8B0207 (0x8B0207 0x00): FSG: Reserved 9 —>

<!— 8B0207 (0x8B0207 0x00): Injector Cylinder #1 Needle Control Valve, Stucks Open —>

<!— 8B0207 (0x8B0207 0x00): Injector Cylinder 1, Needle Control Valve or Amplifier Control Valve, Failed Open or Leakage —>

<!— 8B0207 (0x8B0207 0x00): MU_INJ_STICK_NEEDLE_CYL1 —>

<!— 8B020A (0x8B020A 0x00): Injector Cylinder #1 Needle Control Valve Abnormal Rate of Change —>

<!— 8B020A (0x8B020A 0x00): Injector Cylinder #1 Needle Control Valve, Abnormal Rate of Change —>

<!— 8B0607 (0x8B0607 0x00): Injection Inhibited by Immobilizer (Wrong Key or CAN or EIS Issue) —>

<!— 8C0203 (0x8C0203 0x00): Injector Cylinder #2 Needle Control Valve Abnormal Operation (MAX) —>

<!— 8C0203 (0x8C0203 0x00): Injector Cylinder #2 Needle Control Valve, Abnormal Operation (MAX) —>

<!— 8C0204 (0x8C0204 0x00): Injector Cylinder #2 Needle Control Valve Abnormal Operation (MIN) —>

<!— 8C0204 (0x8C0204 0x00): Injector Cylinder #2 Needle Control Valve, Abnormal Operation (MIN) —>

<!— 8C0205 (0x8C0205 0x00): Injector Cylinder #2 Needle Control Valve, Circuit Open —>

<!— 8C0205 (0x8C0205 0x00): MU_OFD_CYL2_INJ_OPEN_LOAD —>

<!— 8C0206 (0x8C0206 0x00): Injector Cylinder #2 Needle Control Valve, Valve Shorted Circuit —>

<!— 8C0207 (0x8C0207 0x00): FSG: Reserved 10 —>

<!— 8C0207 (0x8C0207 0x00): Injector Cylinder #2 Needle Control Valve, Stucks Open —>

<!— 8C0207 (0x8C0207 0x00): Injector Cylinder 2, Needle Control Valve or Amplifier Control Valve, Failed Open or Leakage —>

<!— 8C0207 (0x8C0207 0x00): MU_INJ_STICK_NEEDLE_CYL2 —>

<!— 8C020A (0x8C020A 0x00): Injector Cylinder #2 Needle Control Valve Abnormal Rate of Change —>

<!— 8C020A (0x8C020A 0x00): Injector Cylinder #2 Needle Control Valve, Abnormal Rate of Change —>

<!— 8D0203 (0x8D0203 0x00): Injector Cylinder #3 Needle Control Valve Abnormal Operation (MAX) —>

<!— 8D0203 (0x8D0203 0x00): Injector Cylinder #3 Needle Control Valve, Abnormal Operation (MAX) —>

<!— 8D0204 (0x8D0204 0x00): Injector Cylinder #3 Needle Control Valve Abnormal Operation (MIN) —>

<!— 8D0204 (0x8D0204 0x00): Injector Cylinder #3 Needle Control Valve, Abnormal Operation (MIN) —>

<!— 8D0205 (0x8D0205 0x00): FSG: Reserved 5 —>

<!— 8D0205 (0x8D0205 0x00): Injector Cylinder #3 Needle Control Valve, Circuit Open —>

<!— 8D0205 (0x8D0205 0x00): Injector Cylinder 3, Needle Control Valve or Amplifier, Failed Closed —>

<!— 8D0205 (0x8D0205 0x00): MU_OFD_CYL3_INJ_OPEN_LOAD —>

<!— 8D0206 (0x8D0206 0x00): Injector Cylinder #3 Needle Control Valve, Valve Shorted Circuit —>

<!— 8D0207 (0x8D0207 0x00): FSG: Reserved 11 —>

<!— 8D0207 (0x8D0207 0x00): Injector Cylinder #3 Needle Control Valve, Stucks Open —>

<!— 8D0207 (0x8D0207 0x00): Injector Cylinder 3, Needle Control Valve or Amplifier Control Valve, Failed Open or Leakage —>

<!— 8D0207 (0x8D0207 0x00): MU_INJ_STICK_NEEDLE_CYL3 —>

<!— 8D020A (0x8D020A 0x00): Injector Cylinder #3 Needle Control Valve Abnormal Rate of Change —>

<!— 8D020A (0x8D020A 0x00): Injector Cylinder #3 Needle Control Valve, Abnormal Rate of Change —>

<!— 8E0203 (0x8E0203 0x00): Injector Cylinder #4 Needle Control Valve Abnormal Operation (MAX) —>

<!— 8E0203 (0x8E0203 0x00): Injector Cylinder #4 Needle Control Valve, Abnormal Operation (MAX) —>

<!— 8E0204 (0x8E0204 0x00): Injector Cylinder #4 Needle Control Valve Abnormal Operation (MIN) —>

<!— 8E0204 (0x8E0204 0x00): Injector Cylinder #4 Needle Control Valve, Abnormal Operation (MIN) —>

<!— 8E0205 (0x8E0205 0x00): FSG: Reserved 6 —>

<!— 8E0205 (0x8E0205 0x00): Injector Cylinder #4 Needle Control Valve, Circuit Open —>

<!— 8E0205 (0x8E0205 0x00): Injector Cylinder 4, Needle Control Valve or Amplifier, Failed Closed —>

<!— 8E0205 (0x8E0205 0x00): MU_OFD_CYL4_INJ_OPEN_LOAD —>

<!— 8E0206 (0x8E0206 0x00): Injector Cylinder #4 Needle Control Valve, Valve Shorted Circuit —>

<!— 8E0207 (0x8E0207 0x00): FSG: Reserved 12 —>

<!— 8E0207 (0x8E0207 0x00): Injector Cylinder #4 Needle Control Valve, Stucks Open —>

<!— 8E0207 (0x8E0207 0x00): Injector Cylinder 4, Needle Control Valve or Amplifier Control Valve, Failed Open or Leakage —>

<!— 8E0207 (0x8E0207 0x00): MU_INJ_STICK_NEEDLE_CYL4 —>

<!— 8E020A (0x8E020A 0x00): Injector Cylinder #4 Needle Control Valve Abnormal Rate of Change —>

<!— 8E020A (0x8E020A 0x00): Injector Cylinder #4 Needle Control Valve, Abnormal Rate of Change —>

<!— 8E0D03 (0x8E0D03 0x00): Actuator Turbo Compound Bypass Circuit Failed High —>

<!— 8E0D04 (0x8E0D04 0x00): Actuator Turbo Compound Bypass Circuit Failed Low —>

<!— 8E0D05 (0x8E0D05 0x00): Actuator Turbo Compound Bypass Circuit Failed Open —>

<!— 8F0203 (0x8F0203 0x00): Injector Cylinder #5 Needle Control Valve Abnormal Operation (MAX) —>

<!— 8F0203 (0x8F0203 0x00): Injector Cylinder #5 Needle Control Valve, Abnormal Operation (MAX) —>

<!— 8F0204 (0x8F0204 0x00): Injector Cylinder #5 Needle Control Valve Abnormal Operation (MIN) —>

<!— 8F0204 (0x8F0204 0x00): Injector Cylinder #5 Needle Control Valve, Abnormal Operation (MIN) —>

<!— 8F0205 (0x8F0205 0x00): FSG: Reserved 7 —>

<!— 8F0205 (0x8F0205 0x00): Injector Cylinder #5 Needle Control Valve, Circuit Open —>

<!— 8F0205 (0x8F0205 0x00): Injector Cylinder 5, Needle Control Valve or Amplifier, Failed Closed —>

<!— 8F0205 (0x8F0205 0x00): MU_OFD_CYL5_INJ_OPEN_LOAD —>

<!— 8F0206 (0x8F0206 0x00): Injector Cylinder #5 Needle Control Valve, Valve Shorted Circuit —>

<!— 8F0207 (0x8F0207 0x00): FSG: Reserved 13 —>

<!— 8F0207 (0x8F0207 0x00): Injector Cylinder #5 Needle Control Valve, Stucks Open —>

<!— 8F0207 (0x8F0207 0x00): Injector Cylinder 5, Needle Control Valve or Amplifier Control Valve, Failed Open or Leakage —>

<!— 8F0207 (0x8F0207 0x00): MU_INJ_STICK_NEEDLE_CYL5 —>

<!— 8F020A (0x8F020A 0x00): Injector Cylinder #5 Needle Control Valve Abnormal Rate of Change —>

<!— 8F020A (0x8F020A 0x00): Injector Cylinder #5 Needle Control Valve, Abnormal Rate of Change —>

<!— 8F0D03 (0x8F0D03 0x00): HC Doser Circuit Failed High —>

<!— 8F0D04 (0x8F0D04 0x00): HC Doser Circuit Failed Low —>

<!— 8F0D05 (0x8F0D05 0x00): HC Doser Circuit Failed Open —>

<!— 900203 (0x900203 0x00): Injector Cylinder #6 Needle Control Valve Abnormal Operation (MAX) —>

<!— 900203 (0x900203 0x00): Injector Cylinder #6 Needle Control Valve, Abnormal Operation (MAX) —>

<!— 900204 (0x900204 0x00): Injector Cylinder #6 Needle Control Valve Abnormal Operation (MIN) —>

<!— 900204 (0x900204 0x00): Injector Cylinder #6 Needle Control Valve, Abnormal Operation (MIN) —>

<!— 900205 (0x900205 0x00): FSG: Reserved 8 —>

<!— 900205 (0x900205 0x00): Injector Cylinder #6 Needle Control Valve, Circuit Open —>

<!— 900205 (0x900205 0x00): Injector Cylinder 6, Needle Control Valve or Amplifier, Failed Closed —>

<!— 900205 (0x900205 0x00): MU_OFD_CYL6_INJ_OPEN_LOAD —>

<!— 900206 (0x900206 0x00): Injector Cylinder #6 Needle Control Valve, Valve Shorted Circuit —>

<!— 900207 (0x900207 0x00): FSG: Reserved 14 —>

<!— 900207 (0x900207 0x00): Injector Cylinder #6 Needle Control Valve, Stucks Open —>

<!— 900207 (0x900207 0x00): Injector Cylinder 6, Needle Control Valve or Amplifier Control Valve, Failed Open or Leakage —>

<!— 900207 (0x900207 0x00): MU_INJ_STICK_NEEDLE_CYL6 —>

<!— 90020A (0x90020A 0x00): Injector Cylinder #6 Needle Control Valve Abnormal Rate of Change —>

<!— 90020A (0x90020A 0x00): Injector Cylinder #6 Needle Control Valve, Abnormal Rate of Change —>

<!— 900C02 (0x900C02 0x00): NOX Inlet Sensor Plausibility Error —>

<!— 900C0A (0x900C0A 0x00): MU_NOX_INTRU_IDLE —>

<!— 900C0F (0x900C0F 0x00): NOX Sensor Drift Check (High) —>

<!— 900C11 (0x900C11 0x00): NOX Sensor Drift Check (Low) —>

<!— 900C14 (0x900C14 0x00): Nox Inlet Sensor Drift High —>

<!— 900C14 (0x900C14 0x00): SCR Nox Inlet Sensor Drift High —>

<!— 900C15 (0x900C15 0x00): Nox Inlet Sensor Drift Low —>

<!— 900C15 (0x900C15 0x00): SCR Nox Inlet Sensor Drift Low —>

<!— 901200 (0x901200 0x00): EGR Cooler Low Efficiency —>

<!— 90120F (0x90120F 0x00): EGR Cooler Performance Monitor —>

<!— 901210 (0x901210 0x00): Cooling Efficiency of EGR Cooler too Low —>

<!— 901210 (0x901210 0x00): FSG: Cooling efficiency of EGR cooler to low —>

<!— 90121F (0x90121F 0x00): EGR Cooler Performance Monitor —>

<!— 91020A (0x91020A 0x00): EGR valve temperature to high —>

<!— 91020A (0x91020A 0x00): EGR Valve Temperature too High —>

<!— 91020A (0x91020A 0x00): FSG: EGR valve temperature to high —>

<!— 91020E (0x91020E 0x00): EGR Valve Failed to Attain Closed Position —>

<!— 91020E (0x91020E 0x00): EGR Valve Failed to attain closed position —>

<!— 91020E (0x91020E 0x00): FSG: EGR Valve Failed to attain closed position —>

<!— 92020A (0x92020A 0x00): EGR Valve Position Deviation too High —>

<!— 92020A (0x92020A 0x00): EGR valve position deviation too high —>

<!— 92020A (0x92020A 0x00): FSG: EGR valve position deviation too high —>

<!— 92020E (0x92020E 0x00): EGR Valve Failed to Attain Open Position —>

<!— 92020E (0x92020E 0x00): EGR Valve Failed to attain open position —>

<!— 92020E (0x92020E 0x00): FSG: EGR Valve Failed to attain open position —>

<!— 940402 (0x940402 0x00): Coolant Temp/Compressor Inlet Temp Plausibility Error —>

<!— 940402 (0x940402 0x00): Coolant Temperature / Compressor Inlet Temperature Plausibility Error —>

<!— 940403 (0x940403 0x00): Turbo Charger Compressor Inlet Temperature Circuit Failed High —>

<!— 940403 (0x940403 0x00): Turbocharger Compressor Inlet Temperature Circuit Failed High —>

<!— 940404 (0x940404 0x00): Turbo Charger Compressor Inlet Temperature Circuit Failed Low —>

<!— 940404 (0x940404 0x00): Turbocharger Compressor Inlet Temperature Circuit Failed Low —>

<!— 940414 (0x940414 0x00): Turbo Charger Compressor Inlet Temperature Sensor, General Temperature Plausibility Error —>

<!— 940414 (0x940414 0x00): Turbocharger Compressor Inlet Temp. Sensor, General Temp. Plausibility Error —>

<!— 94041F (0x94041F 0x00): MU_RC4_T_COMP_IN_GEN2 —>

<!— 970C03 (0x970C03 0x00): HO2S Heater Control Circuit (High Side), short-circuit to battery —>

<!— 970C03 (0x970C03 0x00): HO2S Heater Control Circuit (High Side), Short-Circuit to Battery —>

<!— 970C03 (0x970C03 0x00): MU_CMP_EGCP_HEAT_HS_SC_BAT —>

<!— 970C04 (0x970C04 0x00): HO2S Heater Control Circuit (High Side), short-circuit to ground —>

<!— 970C04 (0x970C04 0x00): HO2S Heater Control Circuit (High Side), Short-Circuit to Ground —>

<!— 970C04 (0x970C04 0x00): MU_CMP_EGCP_HEAT_HS_SC_GND —>

<!— 980402 (0x980402 0x00): FSG: Icooler out pressure plausibility fault, pressure to high (low box) —>

<!— 980414 (0x980414 0x00): FSG: Icooler out pressure plausibility fault, pressure to low (high box) —>

<!— 980414 (0x980414 0x00): Icooler Out Pressure Plausibility Fault, Pressure too Low (High Box) —>

<!— 980D00 (0x980D00 0x00): Fuel Compensation Pressure High —>

<!— 980D01 (0x980D01 0x00): Doser Fuel Supply Pressure Abnormal —>

<!— 980D02 (0x980D02 0x00): Doser Fuel Line Pressure Low —>

<!— 980D03 (0x980D03 0x00): Fuel Compensation Pressure Sensor Circuit Failed High —>

<!— 980D04 (0x980D04 0x00): Fuel Compensation Pressure Sensor Circuit Failed Low —>

<!— 980D0E (0x980D0E 0x00): Doser FLP Sensors Failed Self Test —>

<!— 980D10 (0x980D10 0x00): Fuel Pressure too High / too Low —>

<!— 980D10 (0x980D10 0x00): Fuel Pressure Too High/Too Low —>

<!— 980D15 (0x980D15 0x00): Fuel Cut Off Valve Pressure Not Plausible —>

<!— 980D1F (0x980D1F 0x00): Fuel Cut Off Valve Pressure Not Plausible —>

<!— 990B03 (0x990B03 0x00): FSG: PCV current deviation too high —>

<!— 990B03 (0x990B03 0x00): PCV Current Deviation too High —>

<!— 990B03 (0x990B03 0x00): PCV current deviation too high —>

<!— 990B04 (0x990B04 0x00): FSG: PCV current too low —>

<!— 990B04 (0x990B04 0x00): PCV Current too Low —>

<!— 990B04 (0x990B04 0x00): PCV current too low —>

<!— 9A0D03 (0x9A0D03 0x00): Fuel Cut Off Valve Circuit Failed High —>

<!— 9A0D04 (0x9A0D04 0x00): Fuel Cut Off Valve Circuit Failed Low —>

<!— 9A0D05 (0x9A0D05 0x00): Fuel Cut Off Valve Circuit Failed Open —>

<!— 9A0D07 (0x9A0D07 0x00): FCV Failed Self Test —>

<!— 9A0D11 (0x9A0D11 0x00): DDV Error Detected During Non Regeneration Mode —>

<!— 9B0100 (0x9B0100 0x00): EGR Differential Pressure Failed (dp_egr_high in the Low Box) —>

<!— 9B0100 (0x9B0100 0x00): EGR Differential Pressure Failed (High Box) —>

<!— 9B0100 (0x9B0100 0x00): EGR Differential Pressure Failed (Low Box) —>

<!— 9B0101 (0x9B0101 0x00): EGR Differential Pressure Failed (dp_egr_low in the High Box) —>

<!— 9B0101 (0x9B0101 0x00): EGR Differential Pressure Failed (High Box) —>

<!— 9B0101 (0x9B0101 0x00): EGR Differential Pressure Failed (Low Box) —>

<!— 9B0102 (0x9B0102 0x00): EGR Delta Pressure Sensor Out of Calibration Low —>

<!— 9B0102 (0x9B0102 0x00): FSG: EGR Delta Pressure Sensor Out Of Calibration Low —>

<!— 9B0103 (0x9B0103 0x00): EGR Delta Pressure Sensor Circuit High —>

<!— 9B0104 (0x9B0104 0x00): EGR Delta Pressure Sensor Circuit Low —>

<!— 9B010D (0x9B010D 0x00): EGR Delta Pressure Sensor Out of Calibration High —>

<!— 9B010D (0x9B010D 0x00): FSG: EGR Delta Pressure Sensor Out Of Calibration High —>

<!— 9C0100 (0x9C0100 0x00): EGR Temperature Very High —>

<!— 9C0102 (0x9C0102 0x00): EGR Temperature Sensor, General Temp. Plausibility Error —>

<!— 9C0102 (0x9C0102 0x00): EGR Temperature Sensor, General Temperature Plausibility Error —>

<!— 9C0103 (0x9C0103 0x00): EGR Temperature Sensor Circuit Failed High —>

<!— 9C0104 (0x9C0104 0x00): EGR Temperature Sensor Circuit Failed Low —>

<!— 9C010F (0x9C010F 0x00): EGR Valve Temperature too High —>

<!— 9C0110 (0x9C0110 0x00): EGR Temperature Sensor / Temperature Too High —>

<!— 9C0110 (0x9C0110 0x00): EGR Temperature Sensor / Temperature too High —>

<!— 9C0114 (0x9C0114 0x00): EGR Temperature Drift (High Box) —>

<!— 9C0115 (0x9C0115 0x00): EGR Temperature Drift (Low Box) —>

<!— 9C0403 (0x9C0403 0x00): MU_IS4_T_TURB_IN_SRH —>

<!— 9C0403 (0x9C0403 0x00): tbd —>

<!— 9C0404 (0x9C0404 0x00): MU_IS4_TURB_IN_SRL —>

<!— 9D0002 (0x9D0002 0x00): Fuel Rail Pressure Sensor Signal Erratic —>

<!— 9D0004 (0x9D0004 0x00): FSG: Pressure control valve ( Low side ) error —>

<!— 9D0004 (0x9D0004 0x00): Pressure control valve ( Low side ) error —>

<!— 9D0004 (0x9D0004 0x00): Pressure Control Valve (Low Side) Error —>

<!— 9D000A (0x9D000A 0x00): FSG: Undercapacity in high pressure circuit —>

<!— 9D000A (0x9D000A 0x00): Undercapacity in High Pressure Circuit —>

<!— 9D000E (0x9D000E 0x00): MU_RPG_LPC_LEAK_MON_ERROR —>

<!— 9D000F (0x9D000F 0x00): MU_RPG_P_RAIL_DEV_SERV_LPC —>

<!— 9D0010 (0x9D0010 0x00): FSG: Fuel Rail pressure too low —>

<!— 9D0010 (0x9D0010 0x00): Fuel Rail Pressure too Low —>

<!— 9D0011 (0x9D0011 0x00): MU_RPG_RP_START_MON_ERROR —>

<!— 9D0011 (0x9D0011 0x00): Rail Pressure Level for Injection Enabling Not Reached —>

<!— 9D0012 (0x9D0012 0x00): FSG: Fuel Rail Pressure too High —>

<!— 9D0012 (0x9D0012 0x00): Fuel Rail Pressure too High —>

<!— 9D1200 (0x9D1200 0x00): MU_EPF_T_EXH_HIGH —>

<!— 9E0002 (0x9E0002 0x00): Ignition Switch Not Plausible —>

<!— A11003 (0xA11003 0x00): FSG: Injector Amplifier Control Valve Cylinder 1, 2, 3 Shorted to Battery —>

<!— A11003 (0xA11003 0x00): Injector Amplifier Control Valve Cylinder #1, #2, #3, Shorted to Battery —>

<!— A11004 (0xA11004 0x00): FSG: Injector Amplifier Control Valve Cylinder 1, 2, 3 Shorted to Ground —>

<!— A11004 (0xA11004 0x00): Injector Amplifier Control Valve Cylinder #1, #2, #3, Shorted to Ground —>

<!— A21003 (0xA21003 0x00): FSG: Injector Amplifier Control Valve Cylinder 4, 5, 6 Shorted to Battery —>

<!— A21003 (0xA21003 0x00): Injector Amplifier Control Valve Cylinder #4, #5, #6, Shorted to Battery —>

<!— A21004 (0xA21004 0x00): FSG: Injector Amplifier Control Valve Cylinder 4, 5, 6 Shorted to Ground —>

<!— A21004 (0xA21004 0x00): Injector Amplifier Control Valve Cylinder #4, #5, #6, Shorted to Ground —>

<!— A40000 (0xA40000 0x00): Quantity Control Valve (Low Side) Error —>

<!— A40002 (0xA40002 0x00): FSG: Overcapacity in high pressure circuit —>

<!— A40002 (0xA40002 0x00): Overcapacity in High Pressure Circuit —>

<!— A40003 (0xA40003 0x00): Rail Pressure Sensor Circuit Failed High —>

<!— A40004 (0xA40004 0x00): Rail Pressure Sensor Circuit Failed Low —>

<!— A40005 (0xA40005 0x00): Rail Pressure Sensor Circuit Failed Open —>

<!— A40007 (0xA40007 0x00): High Pressure Pump, Leakage or TDC Position Wrong —>

<!— A4000F (0xA4000F 0x00): MU_RPG_P_RAIL_DEV_SERV_HPC —>

<!— A40014 (0xA40014 0x00): FSG: Rail Pressure Sensor, signal drift (high) —>

<!— A40014 (0xA40014 0x00): Rail Pressure Sensor, Signal Drift (High) —>

<!— A40015 (0xA40015 0x00): FSG: Rail Pressure Sensor, signal drift (low) —>

<!— A40015 (0xA40015 0x00): Rail Pressure Sensor, Signal Drift (Low) —>

<!— A40403 (0xA40403 0x00): MU_AM_SRA1_SUPPLY_ERROR —>

<!— A40403 (0xA40403 0x00): Smart Remote Actuator 1 (Wastegate), Supply Voltage Out of Range —>

<!— A40407 (0xA40407 0x00): Smart Remote Actuator 1 (Wastegate), Failsafe Mode, Motor On —>

<!— A40407 (0xA40407 0x00): Smart Remote Actuator 1 (Wastegate), Failsafe Mode, Motor Off —>

<!— A40408 (0xA40408 0x00): Smart Remote Actuator 1 (Wastegate), Internal Test Running —>

<!— A40409 (0xA40409 0x00): MU_AM_SRA1_NO_CAN —>

<!— A40409 (0xA40409 0x00): Smart Remote Actuator 1 (Wastegate), Failsafe Mode, Motor Off —>

<!— A40409 (0xA40409 0x00): Smart Remote Actuator 1 (Wastegate), No Communication —>

<!— A4040A (0xA4040A 0x00): MU_AM_SRA1_SLOW_RESPONSE —>

<!— A4040A (0xA4040A 0x00): Smart Remote Actuator 1 (Wastegate), Position Deviation Error 2 —>

<!— A4040B (0xA4040B 0x00): Smart Remote Actuator 1 (Wastegate), Restricted Operability —>

<!— A4040B (0xA4040B 0x00): Smart Remote Actuator 1 (Wastegate), Unknown Error Code —>

<!— A4040B (0xA4040B 0x00): Smart Remote Actuator 1 (Wastegate), Learn Span Too Small Range 2 —>

<!— A4040D (0xA4040D 0x00): MU_AM_SRA1_NO_VALID_SIGNAL —>

<!— A4040D (0xA4040D 0x00): Smart Remote Actuator 1 (Wastegate), Signal Not Valid —>

<!— A4040E (0xA4040E 0x00): MU_AM_SRA1_POWER_LIMITING —>

<!— A4040E (0xA4040E 0x00): Smart Remote Actuator 1 (Wastegate), No Failsafe Mode, Motor Off —>

<!— A4040E (0xA4040E 0x00): Smart Remote Actuator 1 (Wastegate), Actuator Power Limited —>

<!— A4040F (0xA4040F 0x00): Smart Remote Actuator 1 (Wastegate), Temperature Warning —>

<!— A40410 (0xA40410 0x00): Smart Remote Actuator 1 (Wastegate), Temperature Fault —>

<!— A40413 (0xA40413 0x00): FSG: Smart Actuator Indicates EGR Position Error —>

<!— A40413 (0xA40413 0x00): Smart Actuator Indicates EGR Position Error —>

<!— A40413 (0xA40413 0x00): Smart Actuator Indicates Turbo Charger Waste Gate Position Error —>

<!— A40413 (0xA40413 0x00): Smart Remote Actuator 1 (Wastegate), Position Error —>

<!— A4041F (0xA4041F 0x00): Smart Remote Actuator 1 (Wastegate), Unknown Error Code —>

<!— A4041F (0xA4041F 0x00): Smart Remote Actuator 1 (Wastegate), Failsafe Mode, Motor Off —>

<!— A4041F (0xA4041F 0x00): Smart Remote Actuator 1 (Wastegate), Position Deviation Error —>

<!— A50202 (0xA50202 0x00): Starter Switch Inconsistent —>

<!— A50203 (0xA50203 0x00): Engine Starter Relay Shorted to High Source —>

<!— A50204 (0xA50204 0x00): Engine Starter Relay Circuit Failed Low —>

<!— A50205 (0xA50205 0x00): Engine Starter Relay Open Circuit —>

<!— A50207 (0xA50207 0x00): Engine Starter Relay — Starter Does Not Engage —>

<!— A5020B (0xA5020B 0x00): MU_SCL_STARTER_FAULT —>

<!— A5020E (0xA5020E 0x00): Starter Electronic Fault / MCM Internal Failure —>

<!— A50210 (0xA50210 0x00): Starter Electronic Fault / ECU internal (Res) —>

<!— A50210 (0xA50210 0x00): Starter Electronic Fault / ECU Internal (Res) —>

<!— A50212 (0xA50212 0x00): Engine Starter Relay Jammed —>

<!— A5021F (0xA5021F 0x00): Starter Jammed (Tooth to Tooth Jam) —>

<!— A70207 (0xA70207 0x00): Pressure Limiting Valve, Failed to Close —>

<!— A80000 (0xA80000 0x00): Battery Voltage High —>

<!— A80001 (0xA80001 0x00): Battery Voltage Low —>

<!— A80012 (0xA80012 0x00): MU_IS1_U_BATT_LOW —>

<!— AA0C00 (0xAA0C00 0x00): MU_EPF_T_EXH_HIGH —>

<!— AA0C08 (0xAA0C08 0x00): FSG: Reserved 15 —>

<!— AA0C08 (0xAA0C08 0x00): Reserved 15 —>

<!— AA0C08 (0xAA0C08 0x00): Reserved 43 —>

<!— AB0002 (0xAB0002 0x00): Ambient Air Temperature Sensor Range / Performance —>

<!— AB0002 (0xAB0002 0x00): FSG: Ambient Air Temperature Sensor Range/Performance —>

<!— AB0002 (0xAB0002 0x00): MU_RC4_T_AMBIENT_AIR_GEN —>

<!— AB001F (0xAB001F 0x00): MU_RC4_T_AMBIENT_AIR_GEN2 —>

<!— AC0B03 (0xAC0B03 0x00): EGR Water Cooling Regulator Circuit Failed High —>

<!— AC0B04 (0xAC0B04 0x00): EGR Water Cooling Regulator Circuit Failed Low —>

<!— AC0B05 (0xAC0B05 0x00): EGR Water Cooling Regulator Circuit Failed Open —>

<!— AE0000 (0xAE0000 0x00): FSG: Fuel Temperature Before High Pressure Pump Too High —>

<!— AE0000 (0xAE0000 0x00): Fuel Temperature Before High Pressure Pump too High —>

<!— AE0002 (0xAE0002 0x00): Fuel Temperature Sensor, General Temp. Plausibility —>

<!— AE0002 (0xAE0002 0x00): Fuel Temperature Sensor, General Temperature Plausibility —>

<!— AE0003 (0xAE0003 0x00): Fuel Temperature Circuit Failed High —>

<!— AE0004 (0xAE0004 0x00): Fuel Temperature Circuit Failed Low —>

<!— AE0011 (0xAE0011 0x00): MU_IS4_T_FUEL_MC_MON —>

<!— AE0014 (0xAE0014 0x00): MU_RC4_T_FUEL_GEN2 —>

<!— AE0014 (0xAE0014 0x00): Plausibility Error Fuel Temperature Sensor —>

<!— AE001F (0xAE001F 0x00): FSG: Fuel Temperture Not Plausible —>

<!— AE001F (0xAE001F 0x00): Fuel Temperature Not Plausible —>

<!— AF0000 (0xAF0000 0x00): Oil Temperature High Warning —>

<!— AF0002 (0xAF0002 0x00): Engine Oil Temperature Sensor, General Temp. Plausibility —>

<!— AF0002 (0xAF0002 0x00): Engine Oil Temperature Sensor, General Temperature Plausibility —>

<!— AF0003 (0xAF0003 0x00): Engine Oil Temperature Circuit Failed High —>

<!— AF0004 (0xAF0004 0x00): Engine Oil Temperature Circuit Failed Low —>

<!— AF000E (0xAF000E 0x00): Engine Oil Temperature Sensor Plausibility Fault —>

<!— AF000F (0xAF000F 0x00): Oil Temperature High Pre Warning —>

<!— AF000F (0xAF000F 0x00): Oil Temperature High Pre-Warning —>

<!— AF0011 (0xAF0011 0x00): Oil Temperature too Low —>

<!— AF0012 (0xAF0012 0x00): Engine Oil Temperature Rises too Slow or Not At All —>

<!— AF001F (0xAF001F 0x00): MU_RC4_T_ENG_OIL_GEN2 —>

<!— B20C08 (0xB20C08 0x00): FSG: Reserved 16 —>

<!— B20C08 (0xB20C08 0x00): Reserved 16 —>

<!— B20C08 (0xB20C08 0x00): Reserved 44 —>

<!— B50D03 (0xB50D03 0x00): 5V Sensor Supply Bank 1 Circuit Failed High —>

<!— B50D04 (0xB50D04 0x00): 5V Sensor Supply Bank 1 Circuit Failed Low —>

<!— B60D03 (0xB60D03 0x00): 5V Sensor Supply Bank 2 Circuit Failed High —>

<!— B60D04 (0xB60D04 0x00): 5V Sensor Supply Bank 2 Circuit Failed Low —>

<!— B70D03 (0xB70D03 0x00): 3V Sensor Supply Bank 1 Circuit Failed High —>

<!— B70D04 (0xB70D04 0x00): 3V Sensor Supply Bank 1 Circuit Failed Low —>

<!— B80D03 (0xB80D03 0x00): 3V Sensor Supply Bank 2 Circuit Failed High —>

<!— B80D04 (0xB80D04 0x00): 3V Sensor Supply Bank 2 Circuit Failed Low —>

<!— B90D03 (0xB90D03 0x00): MU_ISP_U12_SRH —>

<!— B90D04 (0xB90D04 0x00): MU_ISP_U12_SRL —>

<!— BA0203 (0xBA0203 0x00): Gridheater Circuit Failed High —>

<!— BA0204 (0xBA0204 0x00): Gridheater Circuit Failed Low —>

<!— BA0205 (0xBA0205 0x00): Gridheater Circuit Failed Open —>

<!— BA0D03 (0xBA0D03 0x00): MU_ISP_UB_plus_10_SRH —>

<!— BA0D04 (0xBA0D04 0x00): MU_ISP_UB_plus_10_SRL —>

<!— BC001F (0xBC001F 0x00): Idle Speed Out of range —>

<!— BC001F (0xBC001F 0x00): Idle Speed Out of Range —>

<!— BE0000 (0xBE0000 0x00): Engine Speed High —>

<!— BE000F (0xBE000F 0x00): MU_EPF_ENG_SPEED_PREWARN —>

<!— BE0010 (0xBE0010 0x00): MU_EPF_ENGINE_OVERSPEED —>

<!— BE0011 (0xBE0011 0x00): MU_EPF_ENG_SPEED_PREWARN —>

<!— BF000D (0xBF000D 0x00): J1939 Transmission Output Shaft Speed Signal is missing —>

<!— BF000D (0xBF000D 0x00): J1939 Transmission Output Shaft Speed Signal is Missing —>

<!— BF0013 (0xBF0013 0x00): J1939 Transmission Output Shaft Speed Signal is erratic —>

<!— BF0013 (0xBF0013 0x00): J1939 Transmission Output Shaft Speed Signal is Erratic —>

<!— C01407 (0xC01407 0x00): MU_RC4_P_INT_LOW_CEL —>

<!— C10203 (0xC10203 0x00): Digital Output 1 13 Circuit Failed High —>

<!— C10204 (0xC10204 0x00): Digital Output 1 13 Circuit Failed Low —>

<!— C31505 (0xC31505 0x00): PCV Current too Low —>

<!— C31506 (0xC31506 0x00): PCV Current Deviation too High —>

<!— C31507 (0xC31507 0x00): Pressure Limiting Valve, Failed to Close —>

<!— C60203 (0xC60203 0x00): Digital Output 4 06 Circuit Failed High —>

<!— C60204 (0xC60204 0x00): Digital Output 4 06 Circuit Failed Low —>

<!— C91203 (0xC91203 0x00): Catalyst Temperature Sensor Circuit Low Input (Bank 1 Sensor 1) —>

<!— C91204 (0xC91204 0x00): Catalyst Temperature Sensor Circuit High Input (Bank 1 Sensor 1) —>

<!— CA1203 (0xCA1203 0x00): Catalyst Temperature Sensor Circuit Low (Bank 1 Sensor 2) —>

<!— CA1204 (0xCA1204 0x00): Catalyst Temperature Sensor Circuit High (Bank 1 Sensor 2) —>

<!— CB0203 (0xCB0203 0x00): High Side Digital Output # 1 Circuit Failed High —>

<!— CB0204 (0xCB0204 0x00): High Side Digital Output # 1 Circuit Failed Low —>

<!— CB140D (0xCB140D 0x00): Excessive Time to Enter Closed Loop Fuel Pressure Control —>

<!— CC0204 (0xCC0204 0x00): High Side Digital Output # 2 Circuit Failed Low —>

<!— CC0205 (0xCC0205 0x00): High Side Digital Output # 2 Circuit Failed Open —>

<!— CE1203 (0xCE1203 0x00): Water Pump Circuit Failed High —>

<!— CE1204 (0xCE1204 0x00): Water Pump Circuit Failed Low —>

<!— CE1205 (0xCE1205 0x00): Water Pump Circuit Failed Open —>

<!— CF0409 (0xCF0409 0x00): ACM Message Not Received or has Stopped Arriving —>

<!— D0070D (0xD0070D 0x00): MCM / ACM Freeze Frame Version Incompatible —>

<!— D1030D (0xD1030D 0x00): FAN Initialization Failed, Internal Error —>

<!— D1030E (0xD1030E 0x00): FAN Clutch Issue —>

<!— D30201 (0xD30201 0x00): Camshaft Position Sensor Short to Ground —>

<!— D30201 (0xD30201 0x00): Camshaft Position Sensor Signal Voltage Too Low —>

<!— D30203 (0xD30203 0x00): Camshaft Position Sensor Open Circuit —>

<!— D30204 (0xD30204 0x00): Camshaft Position Sensor Short to Ground —>

<!— D30204 (0xD30204 0x00): Camshaft Position Sensor Signal Voltage Too Low —>

<!— D30204 (0xD30204 0x00): Camshaft Position Sensor Signal Voltage too Low —>

<!— D30207 (0xD30207 0x00): MU_EPF_CAM_CRACK —>

<!— D30208 (0xD30208 0x00): Camshaft Position Sensor Time Out —>

<!— D3020A (0xD3020A 0x00): Camshaft Position Sensor Signal Erratic —>

<!— D3020B (0xD3020B 0x00): Camkshaft Position Sensor Failure —>

<!— D3020B (0xD3020B 0x00): Camshaft Position Sensor Failure —>

<!— D3020E (0xD3020E 0x00): Camshaft Position Sensor Pins Swapped —>

<!— D3021F (0xD3021F 0x00): MU_EPF_CAM_REVERSE_DIR_ERR —>

<!— D3021F (0xD3021F 0x00): Reverse Engine Rotation Detected —>

<!— D40202 (0xD40202 0x00): MU_EGCP_DIA_LBD_FIRED_HIGH —>

<!— D40203 (0xD40203 0x00): HO2S Heater Control Circuit (Low Side), short-circuit to battery —>

<!— D40203 (0xD40203 0x00): HO2S Heater Control Circuit (Low Side), Short-Circuit to Battery —>

<!— D40203 (0xD40203 0x00): MU_CMP_EGCP_HEAT_LS_SC_BAT —>

<!— D40204 (0xD40204 0x00): HO2S Heater Control Circuit (Low Side) short-circuit to ground —>

<!— D40204 (0xD40204 0x00): HO2S Heater Control Circuit (Low Side), Short-Circuit to Ground —>

<!— D40204 (0xD40204 0x00): MU_CMP_EGCP_HEAT_LS_SC_GND —>

<!— D40205 (0xD40205 0x00): HO2S Heater Control Circuit, Open Load —>

<!— D40205 (0xD40205 0x00): MU_CMP_EGCP_HEAT_OPEN_LOAD —>

<!— D40206 (0xD40206 0x00): FSG: HO2S Heater Control Circuit Range/Performance (Bank1, Sensor1) —>

<!— D40206 (0xD40206 0x00): HO2S Heater Control Circuit Range / Performance (Bank1, Sensor1) —>

<!— D40206 (0xD40206 0x00): MU_CMP_EGCP_HEAT_OVER_LOAD —>

<!— D40207 (0xD40207 0x00): MU_EGCP_DIAG_LSL_DYN —>

<!— D4020B (0xD4020B 0x00): MU_EGCP_DIA_VLS_OFS_LIM —>

<!— D4020E (0xD4020E 0x00): MU_EGCP_DIA_I_PMP_LIM —>

<!— D4021F (0xD4021F 0x00): MU_EGCP_DIA_V_PMP_LIM —>

<!— D41509 (0xD41509 0x00): CAN3 Communication Error —>

<!— D41513 (0xD41513 0x00): CAN3 Electrical Failure —>

<!— D90200 (0xD90200 0x00): Grid Heater Permanently On —>

<!— D90202 (0xD90202 0x00): Grid Heater Circuit Failed Low —>

<!— D90203 (0xD90203 0x00): Gridheater Circuit Failed High —>

<!— D90204 (0xD90204 0x00): Grid Heater Circuit Failed Low —>

<!— D90204 (0xD90204 0x00): Gridheater Circuit Failed Low —>

<!— D90205 (0xD90205 0x00): Gridheater Circuit Failed Open —>

<!— D90207 (0xD90207 0x00): Grid Heater Defect —>

<!— E70A00 (0xE70A00 0x00): EGR Valve Actuator, No Failsafe Mode, Motor Off —>

<!— E70A00 (0xE70A00 0x00): EGR Valve Actuator, Temperature Alert —>

<!— E70A00 (0xE70A00 0x00): Smart Remote Actuator 3 (EGR), Temperature Alert —>

<!— E70A02 (0xE70A02 0x00): EGR Valve Actuator, Position Deviation Error —>

<!— E70A02 (0xE70A02 0x00): EGR Valve Actuator, Temperature Fault —>

<!— E70A02 (0xE70A02 0x00): Smart Remote Actuator 3 (EGR), Position Deviation Error —>

<!— E70A03 (0xE70A03 0x00): EGR Valve Circuit Failed High —>

<!— E70A04 (0xE70A04 0x00): EGR Valve Circuit Failed Low —>

<!— E70A05 (0xE70A05 0x00): EGR Valve Circuit Failed Open —>

<!— E70A07 (0xE70A07 0x00): EGR Valve Actuator, Failsafe Mode, Motor On —>

<!— E70A07 (0xE70A07 0x00): EGR Valve Actuator, Failsafe Mode, Motor Off —>

<!— E70A07 (0xE70A07 0x00): EGR Valve Actuator, Restricted Operability —>

<!— E70A07 (0xE70A07 0x00): Smart Remote Actuator 3 (EGR), Failsafe Mode, Motor Off —>

<!— E70A08 (0xE70A08 0x00): EGR Valve Actuator, Internal Test Running —>

<!— E70A09 (0xE70A09 0x00): EGR Valve Actuator, Failsafe Mode, Motor Off —>

<!— E70A09 (0xE70A09 0x00): EGR Valve Actuator, No Communication —>

<!— E70A09 (0xE70A09 0x00): MU_AM_SRA3_NO_CAN —>

<!— E70A09 (0xE70A09 0x00): Smart Remote Actuator 3 (EGR), No Communication —>

<!— E70A0A (0xE70A0A 0x00): EGR Actuator Slow Response —>

<!— E70A0B (0xE70A0B 0x00): EGR Valve Actuator, Common Failure —>

<!— E70A0B (0xE70A0B 0x00): EGR Valve Actuator, Restricted Operability —>

<!— E70A0B (0xE70A0B 0x00): MU_AM_SRA3_COMMON_FAILURE —>

<!— E70A0B (0xE70A0B 0x00): Smart Remote Actuator 3 (EGR), Common Failure —>

<!— E70A0C (0xE70A0C 0x00): EGR Valve Actuator, Frozen —>

<!— E70A0C (0xE70A0C 0x00): MU_AM_SRA3_FROZEN —>

<!— E70A0C (0xE70A0C 0x00): Smart Remote Actuator 3 (EGR), Valve frozen —>

<!— E70A0D (0xE70A0D 0x00): MU_AM_SRA3_NO_VALID_SIGNAL —>

<!— E70A0D (0xE70A0D 0x00): Smart Remote Actuator 3 (EGR), Signal Not Valid —>

<!— E70A0E (0xE70A0E 0x00): EGR Valve Actuator, No Failsafe Mode, Motor Off —>

<!— E70A0E (0xE70A0E 0x00): EGR Valve Actuator, Wrong Failsafe Calibration —>

<!— E70A0E (0xE70A0E 0x00): MU_AM_SRA3_FAILSAFE_ERR —>

<!— E70A0E (0xE70A0E 0x00): Smart Remote Actuator 3 (EGR), Wrong Failsafe Calibration —>

<!— E70A0F (0xE70A0F 0x00): EGR Valve Actuator, Failsafe Mode, Motor Off —>

<!— E70A0F (0xE70A0F 0x00): EGR Valve Actuator, Temperature Warning —>

<!— E70A0F (0xE70A0F 0x00): Smart Remote Actuator 3 (EGR), Temperature Warning —>

<!— E70A10 (0xE70A10 0x00): EGR Valve Actuator, Failsafe Mode, Motor On —>

<!— E70A10 (0xE70A10 0x00): EGR Valve Actuator, Learn Cycle Too Large —>

<!— E70A10 (0xE70A10 0x00): EGR Valve Actuator, Temperature Fault —>

<!— E70A10 (0xE70A10 0x00): Smart Remote Actuator 3 (EGR), Learn Cycle Too Large —>

<!— E70A12 (0xE70A12 0x00): EGR Valve Actuator, Learn Cycle Too Small —>

<!— E70A12 (0xE70A12 0x00): MU_AM_SRA3_LEARN_TOO_SMALL —>

<!— E70A12 (0xE70A12 0x00): Smart Remote Actuator 3 (EGR), Learn Span Too Small —>

<!— E70A13 (0xE70A13 0x00): Smart Actuator Indicates EGR Position Error —>

<!— E70A13 (0xE70A13 0x00): Smart Remote Actuator 3 (EGR), Position Error —>

<!— E70A1F (0xE70A1F 0x00): EGR Valve Actuator, Slow Response —>

<!— E70A1F (0xE70A1F 0x00): EGR Valve Actuator, Unknown Error Code —>

<!— E70A1F (0xE70A1F 0x00): MU_AM_SRA3_SLOW_RESPONSE —>

<!— E70A1F (0xE70A1F 0x00): Smart Remote Actuator 3 (EGR), Position Deviation Error 2 —>

<!— EA0C00 (0xEA0C00 0x00): Variable Camshaft Phase, Temperature too High —>

<!— EA0C02 (0xEA0C02 0x00): Variable Camshaft Phase, Position Deviation —>

<!— EA0C03 (0xEA0C03 0x00): Variable Camshaft Phase, Shorted to Battery —>

<!— EA0C04 (0xEA0C04 0x00): Variable Camshaft Phase, Shorted to Ground —>

<!— EA0C05 (0xEA0C05 0x00): Variable Camshaft Phase, Open Load —>

<!— EA0C07 (0xEA0C07 0x00): Variable Camshaft Phase, Clamb Position —>

<!— EA0C0A (0xEA0C0A 0x00): Variable Camshaft Phase, Slow Response —>

<!— EA0C0E (0xEA0C0E 0x00): Variable Camshaft Phase Sensor Adaption Fail —>

<!— EA0C1F (0xEA0C1F 0x00): Variable Camshaft Phase, at State Joggling —>

<!— EB0A09 (0xEB0A09 0x00): CAN3 Communication Error —>

<!— EB0A13 (0xEB0A13 0x00): Smart Actuator Indicates Turbocharger Vane Position Error —>

<!— EB0D00 (0xEB0D00 0x00): Inlet Manifold Pressure Failed High —>

<!— EB0D03 (0xEB0D03 0x00): Intake Manifold Pressure Circuit Failed High —>

<!— EB0D04 (0xEB0D04 0x00): Intake Manifold Pressure Circuit Failed Low —>

<!— EB0D12 (0xEB0D12 0x00): Inlet Manifold Pressure Failed Low —>

<!— EB0D14 (0xEB0D14 0x00): Ambient and Inlet Manifold Pressure Difference (Low Box) —>

<!— EB0D15 (0xEB0D15 0x00): Ambient and Inlet Manifold Pressure Difference (High Box) —>

<!— EC0B0E (0xEC0B0E 0x00): Misfire Detected —>

<!— ED0A03 (0xED0A03 0x00): Injector Needle Control Valve Cylinder 1,2,3 Shorted to Battery —>

<!— ED0A03 (0xED0A03 0x00): Injector Needle Control Valve Cylinder #1, #2, #3, Shorted to Battery —>

<!— ED0A04 (0xED0A04 0x00): Injector Needle Control Valve Cylinder 1, 2, 3 Shorted to Ground —>

<!— ED0A04 (0xED0A04 0x00): Injector Needle Control Valve Cylinder #1, #2, #3, Shorted to Ground —>

<!— ED0A1F (0xED0A1F 0x00): MU_OFD_BANK1_OFF_PULL_FAIL —>

<!— ED0F00 (0xED0F00 0x00): Doser Fuel Line Pressure High —>

<!— ED0F03 (0xED0F03 0x00): Doser Fuel Line Pressure Sensor Circuit Failed High —>

<!— ED0F04 (0xED0F04 0x00): Doser Fuel Line Pressure Sensor Circuit Failed Low —>

<!— ED0F0E (0xED0F0E 0x00): Doser Fuel Line Pressure Failed Self Test —>

<!— ED1410 (0xED1410 0x00): FSG: Total injected fuel mass too high —>

<!— ED1410 (0xED1410 0x00): Total Injected Fuel Mass too High —>

<!— ED1412 (0xED1412 0x00): FSG: Total injected fuel mass too low —>

<!— ED1412 (0xED1412 0x00): Total Injected Fuel Mass too Low —>

<!— ED141F (0xED141F 0x00): MU_ESC_MULTI_CYL —>

<!— EE0A03 (0xEE0A03 0x00): Injector Needle Control Valve Cylinder 4,5,6, Shorted to Battery —>

<!— EE0A03 (0xEE0A03 0x00): Injector Needle Control Valve Cylinder #4, #5, #6, Shorted to Battery —>

<!— EE0A04 (0xEE0A04 0x00): Injector Needle Control Valve Cylinder 4, 5, 6 Shorted to Ground —>

<!— EE0A04 (0xEE0A04 0x00): Injector Needle Control Valve Cylinder #4, #5, #6, Shorted to Ground —>

<!— EE0A1F (0xEE0A1F 0x00): MU_OFD_BANK2_OFF_PULL_FAIL —>

<!— EE1410 (0xEE1410 0x00): Engine Smoothness control / Cylinder #1 Quantity Deficit —>

<!— EE1410 (0xEE1410 0x00): Engine Smoothness Control / Cylinder #1 Quantity Deficit —>

<!— EE1410 (0xEE1410 0x00): FSG: Engine Smoothness control / Cylinder #1 Quantity Deficit —>

<!— EE1412 (0xEE1412 0x00): Engine Smoothness control / Cylinder #1 Quantity Excess —>

<!— EE1412 (0xEE1412 0x00): Engine Smoothness Control / Cylinder #1 Quantity Excess —>

<!— EE1412 (0xEE1412 0x00): FSG: Engine Smoothness control / Cylinder #1 Quantity Excess —>

<!— EF1410 (0xEF1410 0x00): Engine Smoothness control / Cylinder #2 Quantity Deficit —>

<!— EF1410 (0xEF1410 0x00): Engine Smoothness Control / Cylinder #2 Quantity Deficit —>

<!— EF1410 (0xEF1410 0x00): FSG: Engine Smoothness control / Cylinder #2 Quantity Deficit —>

<!— EF1412 (0xEF1412 0x00): Engine Smoothness control / Cylinder #2 Quantity Excess —>

<!— EF1412 (0xEF1412 0x00): Engine Smoothness Control / Cylinder #2 Quantity Excess —>

<!— EF1412 (0xEF1412 0x00): FSG: Engine Smoothness control / Cylinder #2 Quantity Excess —>

<!— F00B02 (0xF00B02 0x00): O2 Sensor, Heater Invalid Sensor Temperature Measurement —>

<!— F00B04 (0xF00B04 0x00): FSG: O2 Sensor, Heater Performance —>

<!— F00B04 (0xF00B04 0x00): MU_EGCP_DIA_TTIP_OOR —>

<!— F00B04 (0xF00B04 0x00): O2 Sensor, Heater Performance —>

<!— F00B05 (0xF00B05 0x00): O2 Sensor Circuit Bank 1 Sensor 1, Open Circuit on Line Vn —>

<!— F00B0E (0xF00B0E 0x00): O2 Sensor, Lambda Rationality During No Fueling —>

<!— F00B14 (0xF00B14 0x00): FSG: Lamda Signal drifted high —>

<!— F00B14 (0xF00B14 0x00): Lamda Signal Drifted High —>

<!— F00B15 (0xF00B15 0x00): FSG: Lamda Signal drifted low —>

<!— F00B15 (0xF00B15 0x00): Lamda Signal Drifted Low —>

<!— F00B1F (0xF00B1F 0x00): MU_RC4_LAMBDA_DEV —>

<!— F01410 (0xF01410 0x00): Engine Smoothness control / Cylinder #3 Quantity Deficit —>

<!— F01410 (0xF01410 0x00): Engine Smoothness Control / Cylinder #3 Quantity Deficit —>

<!— F01410 (0xF01410 0x00): FSG: Engine Smoothness control / Cylinder #3 Quantity Deficit —>

<!— F01412 (0xF01412 0x00): Engine Smoothness control / Cylinder #3 Quantity Excess —>

<!— F01412 (0xF01412 0x00): Engine Smoothness Control / Cylinder #3 Quantity Excess —>

<!— F01412 (0xF01412 0x00): FSG: Engine Smoothness control / Cylinder #3 Quantity Excess —>

<!— F11410 (0xF11410 0x00): Engine Smoothness control / Cylinder #4 Quantity Deficit —>

<!— F11410 (0xF11410 0x00): Engine Smoothness Control / Cylinder #4 Quantity Deficit —>

<!— F11410 (0xF11410 0x00): FSG: Engine Smoothness control / Cylinder #4 Quantity Deficit —>

<!— F11412 (0xF11412 0x00): Engine Smoothness control / Cylinder #4 Quantity Excess —>

<!— F11412 (0xF11412 0x00): Engine Smoothness Control / Cylinder #4 Quantity Excess —>

<!— F11412 (0xF11412 0x00): FSG: Engine Smoothness control / Cylinder #4 Quantity Excess —>

<!— F20B07 (0xF20B07 0x00): EGR Feedback Control Out of Adjustment High —>

<!— F20B09 (0xF20B09 0x00): MU_RC4_EGR_SLOW_RESP_LB —>

<!— F20B0A (0xF20B0A 0x00): Exhaust Gas Recirculation Slow Response —>

<!— F20B0A (0xF20B0A 0x00): FSG: Exhaust Gas Recirculation Slow Response —>

<!— F20B0A (0xF20B0A 0x00): MU_RC4_EGR_SLOW_RESPONSE —>

<!— F20B1F (0xF20B1F 0x00): EGR Feedback Control Out of Adjustment Low —>

<!— F21410 (0xF21410 0x00): Engine Smoothness control / Cylinder #5 Quantity Deficit —>

<!— F21410 (0xF21410 0x00): Engine Smoothness Control / Cylinder #5 Quantity Deficit —>

<!— F21410 (0xF21410 0x00): FSG: Engine Smoothness control / Cylinder #5 Quantity Deficit —>

<!— F21412 (0xF21412 0x00): Engine Smoothness control / Cylinder #5 Quantity Excess —>

<!— F21412 (0xF21412 0x00): Engine Smoothness Control / Cylinder #5 Quantity Excess —>

<!— F21412 (0xF21412 0x00): FSG: Engine Smoothness control / Cylinder #5 Quantity Excess —>

<!— F31410 (0xF31410 0x00): Engine Smoothness control / Cylinder #6 Quantity Deficit —>

<!— F31410 (0xF31410 0x00): Engine Smoothness Control / Cylinder #6 Quantity Deficit —>

<!— F31410 (0xF31410 0x00): FSG: Engine Smoothness control / Cylinder #6 Quantity Deficit —>

<!— F31412 (0xF31412 0x00): Engine Smoothness control / Cylinder #6 Quantity Excess —>

<!— F31412 (0xF31412 0x00): Engine Smoothness Control / Cylinder #6 Quantity Excess —>

<!— F31412 (0xF31412 0x00): FSG: Engine Smoothness control / Cylinder #6 Quantity Excess —>

<!— F41410 (0xF41410 0x00): Engine Smoothness control / Cylinder #7 Quantity Deficit —>

<!— F41410 (0xF41410 0x00): FSG: Engine Smoothness control / Cylinder #7 Quantity Deficit —>

<!— F41412 (0xF41412 0x00): Engine Smoothness control / Cylinder #7 Quantity Excess —>

<!— F41412 (0xF41412 0x00): FSG: Engine Smoothness control / Cylinder #7 Quantity Excess —>

<!— F51410 (0xF51410 0x00): Engine Smoothness control / Cylinder #8 Quantity Deficit —>

<!— F51410 (0xF51410 0x00): FSG: Engine Smoothness control / Cylinder #8 Quantity Deficit —>

<!— F51412 (0xF51412 0x00): Engine Smoothness control / Cylinder #8 Quantity Excess —>

<!— F51412 (0xF51412 0x00): FSG: Engine Smoothness control / Cylinder #8 Quantity Excess —>

<!— FC140F (0xFC140F 0x00): Smart Remote Actuator 1 (Wastegate), No Failsafe Mode, Motor Off —>

<!— FC140F (0xFC140F 0x00): Smart Remote Actuator 1 (Wastegate), Temperature Warning —>

<!— FC1410 (0xFC1410 0x00): MU_AM_SRA1_TEMP_ALERT —>

<!— FC1410 (0xFC1410 0x00): Smart Remote Actuator 1 (Wastegate), Temperature Alert —>

<!— 00F0F0 (0x00F0F0 0x00): EGR Feedback on Lambda too High —>

<!— 00F0F2 (0x00F0F2 0x00): EGR Feedback on Lambda too Low —>

<!— 01F0F0 (0x01F0F0 0x00): EGR Feedback on Lambda too High —>

<!— 02F0EE (0x02F0EE 0x00): MU_EGR_OBD_3 —>

<!— 03F0EE (0x03F0EE 0x00): MU_EGR_OBD_4 —>

<!— 040E03 (0x040E03 0x00): Ether Start, Shorted to Ground —>

<!— 040E04 (0x040E04 0x00): Ether Start, Shorted to Battery —>

<!— 040E05 (0x040E05 0x00): Ether Start, Open Load —>

<!— 04F0EE (0x04F0EE 0x00): MU_EGR_OBD_5 —>

<!— 051403 (0x051403 0x00): MU_ISP_ULIN_SRH —>

<!— 051404 (0x051404 0x00): MU_ISP_ULIN_SRL —>

<!— 05F0EE (0x05F0EE 0x00): MU_OBD_PROTO_EV_1 —>

<!— 06F0EE (0x06F0EE 0x00): MU_OBD_PROTO_EV_2 —>

<!— 07F0EE (0x07F0EE 0x00): MU_OBD_PROTO_EV_3 —>

<!— 080201 (0x080201 0x00): MU_EBM_BRAKE_MALFUNCTION —>

<!— 080212 (0x080212 0x00): MU_EBM_RED_BRAKE_POWER —>

<!— 08F0EE (0x08F0EE 0x00): MU_OBD_PROTO_EV_4 —>

<!— 09040A (0x09040A 0x00): MU_ISP_MCM_TIME_RAT_ERROR —>

<!— 09040F (0x09040F 0x00): MCM Engine Run Timer Plausibility —>

<!— 090411 (0x090411 0x00): MCM Engine Off Timer Plausibility —>

<!— 090412 (0x090412 0x00): MU_IS4_RTC_ENG_OFF_RAT_CHK —>

<!— 09F0EE (0x09F0EE 0x00): MU_OBD_PROTO_EV_5 —>

<!— 0B020D (0x0B020D 0x00): J1939 Transmission Current Gear Signal is Missing —>

<!— 0B0213 (0x0B0213 0x00): J1939 Transmission Current Gear Signal is Erratic —>

<!— 0CF0E3 (0x0CF0E3 0x00): Reserved 2 —>

<!— 0CF0E4 (0x0CF0E4 0x00): Reserved 1 —>

<!— 0D0E03 (0x0D0E03 0x00): Proportional Valve Bank 1 Circuit Failed High —>

<!— 0D0E04 (0x0D0E04 0x00): Proportional Valve Bank 1 Circuit Failed Low —>

<!— 0DF0E3 (0x0DF0E3 0x00): Thermal Switch Circuit Failed High —>

<!— 0DF0E4 (0x0DF0E4 0x00): Thermal Switch Circuit Failed Low —>

<!— 0E0E03 (0x0E0E03 0x00): Proportional Valve Bank 2 Circuit Failed High —>

<!— 0E0E04 (0x0E0E04 0x00): Proportional Valve Bank 2 Circuit Failed Low —>

<!— 0EF0E3 (0x0EF0E3 0x00): Reserved 4 —>

<!— 0EF0E4 (0x0EF0E4 0x00): Reserved 3 —>

<!— 0F0E03 (0x0F0E03 0x00): MCM Internal Injector Power Supply Failed High —>

<!— 0F0E04 (0x0F0E04 0x00): MCM Internal Injector Power Supply Failed Low —>

<!— 0F0E0F (0x0F0E0F 0x00): MCM Internal Injector Power Supply Failed High Sporadic —>

<!— 0F0E11 (0x0F0E11 0x00): MCM internal Injector Power Supply Failed Low Sporadic —>

<!— 0FF0E3 (0x0FF0E3 0x00): EWS Circuit Failed High —>

<!— 0FF0E4 (0x0FF0E4 0x00): EWS Circuit Failed Low —>

<!— 0FF0E5 (0x0FF0E5 0x00): EWS Circuit Failed Open —>

<!— 10F0E3 (0x10F0E3 0x00): Turbo Compound Valve Circuit Failed High —>

<!— 10F0E4 (0x10F0E4 0x00): Turbo Compound Valve Circuit Failed Low —>

<!— 10F0E5 (0x10F0E5 0x00): Turbo Compound Valve Circuit Failed Open —>

<!— 110B02 (0x110B02 0x00): Park Brake Status Not Plausible (Vehicle Moving) —>

<!— 12F0E3 (0x12F0E3 0x00): Function 19 Circuit Failed High —>

<!— 12F0E4 (0x12F0E4 0x00): Function 19 Circuit Failed Low —>

<!— 12F0E5 (0x12F0E5 0x00): Function 19 Circuit Failed Open —>

<!— 13150F (0x13150F 0x00): Idle Fuel Quantity Out of Range —>

<!— 13F0E3 (0x13F0E3 0x00): Service Push Button Circuit Failed High —>

<!— 16F0E3 (0x16F0E3 0x00): Function 22 Circuit Failed High —>

<!— 16F0E4 (0x16F0E4 0x00): Function 22 Circuit Failed Low —>

<!— 16F0E5 (0x16F0E5 0x00): Function 22 Circuit Failed Open —>

<!— 18F0E3 (0x18F0E3 0x00): Function 25 Circuit Failed High —>

<!— 18F0E4 (0x18F0E4 0x00): Function 25 Circuit Failed Low —>

<!— 18F0E5 (0x18F0E5 0x00): Function 25 Circuit Failed Open —>

<!— 19F0E3 (0x19F0E3 0x00): RCP Test Function 1 Circuit Failed High —>

<!— 19F0E4 (0x19F0E4 0x00): RCP Test Function 1 Circuit Failed Low —>

<!— 19F0E5 (0x19F0E5 0x00): RCP Test Function 1 Circuit Failed Open —>

<!— 1AF0E3 (0x1AF0E3 0x00): RCP Test Function 2 Circuit Failed High —>

<!— 1AF0E4 (0x1AF0E4 0x00): RCP Test Function 2 Circuit Failed Low —>

<!— 1AF0E5 (0x1AF0E5 0x00): RCP Test Function 2 Circuit Failed Open —>

<!— 1B0000 (0x1B0000 0x00): EGR Valve Failed to Attain Closed Position —>

<!— 1B0001 (0x1B0001 0x00): EGR Valve Failed to Attain Open Position —>

<!— 1B0002 (0x1B0002 0x00): EGR Valve Position Feedback Failed —>

<!— 1B0003 (0x1B0003 0x00): EGR Valve Position Circuit Failed High —>

<!— 1B0004 (0x1B0004 0x00): EGR Valve Position Circuit Failed Low —>

<!— 1B0007 (0x1B0007 0x00): MU_AM_EGR_SPRING_BROKEN —>

<!— 1B000A (0x1B000A 0x00): EGR Valve Position Deviation too High —>

<!— 1B000C (0x1B000C 0x00): EGR Valve Frozen —>

<!— 1B000E (0x1B000E 0x00): MU_EGR_INT_MON —>

<!— 1B060E (0x1B060E 0x00): Detect Unwanted ECU Change —>

<!— 1BF0E3 (0x1BF0E3 0x00): Volute Control Valve, Shorted to Battery —>

<!— 1BF0E4 (0x1BF0E4 0x00): Volute Control Valve, Shorted to Ground —>

<!— 1BF0E5 (0x1BF0E5 0x00): Volute Control Valve, Open Load —>

<!— 1CF0E3 (0x1CF0E3 0x00): Volute Shut Off Valve, Shorted to Battery —>

<!— 1CF0E4 (0x1CF0E4 0x00): Volute Shut Off Valve, Shorted to Ground —>

<!— 1CF0E5 (0x1CF0E5 0x00): Volute Shut Off Valve, Open Load —>

<!— 1EF0E3 (0x1EF0E3 0x00): Function 31 Circuit Failed High —>

<!— 1EF0E4 (0x1EF0E4 0x00): Function 31 Circuit Failed Low —>

<!— 1EF0E5 (0x1EF0E5 0x00): Function 31 Circuit Failed Open —>

<!— 230D03 (0x230D03 0x00): DEF Tank Heater Circuit Failed High —>

<!— 230D04 (0x230D04 0x00): DEF Tank Heater Circuit Failed Low —>

<!— 230D05 (0x230D05 0x00): DEF Heater Circuit Failed Open —>

<!— 230D11 (0x230D11 0x00): MU_CMP_PVH_UTH_OBD —>

<!— 261703 (0x261703 0x00): Differential Pressure Icooler Out Sensor Circuit Failed High —>

<!— 261704 (0x261704 0x00): Differential Pressure Icooler Out Sensor Circuit Failed Low —>

<!— 26170D (0x26170D 0x00): Icooler Out Differential Pressure Sensor Out of Calibration Low —>

<!— 26170E (0x26170E 0x00): Icooler Out Differential Pressure Sensor Out of Calibration High —>

<!— 261714 (0x261714 0x00): Icooler Out Differential Pressure Plausibility Fault, Pressure too High (Low Box) —>

<!— 261715 (0x261715 0x00): Icooler Out Differential Pressure Plausibility Fault, Pressure too Low (High Box) —>

<!— 271702 (0x271702 0x00): Electronically Controlled Water Pump Limp Home Mode —>

<!— 271707 (0x271707 0x00): Electronically Controlled Water Pump Mechanical Defect Detected —>

<!— 27F0F0 (0x27F0F0 0x00): Max Power Deficit —>

<!— 27F0F2 (0x27F0F2 0x00): Max Power Excess —>

<!— 281703 (0x281703 0x00): H Bridge 2 EGR Valve Circiut Shorted to Battery —>

<!— 281704 (0x281704 0x00): H Bridge 2 EGR Valve Circuit Shorted to Ground —>

<!— 281705 (0x281705 0x00): H Bridge 2 EGR Valve Short Circuit/ Over Current —>

<!— 28170E (0x28170E 0x00): H Bridge 2 EGR Valve Circuit Open Load —>

<!— 29F3FF (0x29F3FF 0x00): MU_CAN_MON_PBS_CAN_NO_COM —>

<!— 2A050A (0x2A050A 0x00): Detection of misfire on more than one cylinder —>

<!— 2A050B (0x2A050B 0x00): Detection of Misfire when misfire rate is above 5% but cylinder can not be clear detected —>

<!— 2A050E (0x2A050E 0x00): Multiple Cylinder Misfire Detected —>

<!— 2A051F (0x2A051F 0x00): Multiple Cylinder Misfire Detected at Idle —>

<!— 2A1503 (0x2A1503 0x00): FMU High Side Short-Circuit to Battery —>

<!— 2A1504 (0x2A1504 0x00): FMU Low Side Short-Circuit to Ground —>

<!— 2B050A (0x2B050A 0x00): Detection of Misfire on cylinder 1 when misfire rate is above 5% —>

<!— 2B050B (0x2B050B 0x00): Cylinder #1 Misfire Detected —>

<!— 2B050E (0x2B050E 0x00): Idle Smoothness Control / Cylinder #1 Quantity Excess at Idle —>

<!— 2B051F (0x2B051F 0x00): Idle Smoothness Control / Cylinder #1 Quantity Deficit at Idle —>

<!— 2C050A (0x2C050A 0x00): Detection of Misfire on cylinder 2 when misfire rate is above 5% —>

<!— 2C050B (0x2C050B 0x00): Cylinder #2 Misfire Detected —>

<!— 2C050E (0x2C050E 0x00): Idle Smoothness Control / Cylinder #2 Quantity Excess at Idle —>

<!— 2C051F (0x2C051F 0x00): Idle Smoothness Control / Cylinder #2 Quantity Deficit at Idle —>

<!— 2CF0EE (0x2CF0EE 0x00): Intermittent Connection in Sensor Electric Circuit 1 —>

<!— 2CF0FF (0x2CF0FF 0x00): Intermittent Connection in Sensor Electric Circuit 2 —>

<!— 2D050A (0x2D050A 0x00): Detection of Misfire on cylinder 3 when misfire rate is above 5% —>

<!— 2D050B (0x2D050B 0x00): Cylinder #3 Misfire Detected —>

<!— 2D050E (0x2D050E 0x00): Idle Smoothness Control / Cylinder #3 Quantity Excess at Idle —>

<!— 2D051F (0x2D051F 0x00): Idle Smoothness Control / Cylinder #3 Quantity Deficit at Idle —>

<!— 2D1509 (0x2D1509 0x00): MU_CAN_MON_SRA1_CAN_NO_COM —>

<!— 2DF3E3 (0x2DF3E3 0x00): MU_OFD_DELTA_UFET_SRH —>

<!— 2DF3E4 (0x2DF3E4 0x00): MU_OFD_DELTA_UFET_SRL —>

<!— 2E050A (0x2E050A 0x00): Detection of Misfire on cylinder 4 when misfire rate is above 5% —>

<!— 2E050B (0x2E050B 0x00): Cylinder #4 Misfire Detected —>

<!— 2E050E (0x2E050E 0x00): Idle Smoothness Control / Cylinder #4 Quantity Excess at Idle —>

<!— 2E051F (0x2E051F 0x00): Idle Smoothness Control / Cylinder #4 Quantity Deficit at Idle —>

<!— 2EF0EE (0x2EF0EE 0x00): Dashboard Doesn’t Get MCM DM1 Information —>

<!— 2EF0FF (0x2EF0FF 0x00): Dashboard DM1 Defect —>

<!— 2EF3EE (0x2EF3EE 0x00): Test MU1 for similiar Conditions —>

<!— 2EF3FF (0x2EF3FF 0x00): MU_FMM_AS_ET_TEST1 —>

<!— 2F0403 (0x2F0403 0x00): Fan Stage 2 Circuit Failed High —>

<!— 2F0404 (0x2F0404 0x00): Fan Stage 2 Circuit Failed Low —>

<!— 2F0405 (0x2F0405 0x00): Fan Stage 2 Circuit Failed Open —>

<!— 2F050A (0x2F050A 0x00): Detection of Misfire on cylinder 5 when misfire rate is above 5% —>

<!— 2F050B (0x2F050B 0x00): Cylinder #5 Misfire Detected —>

<!— 2F050E (0x2F050E 0x00): Idle Smoothness Control / Cylinder #5 Quantity Excess at Idle —>

<!— 2F051F (0x2F051F 0x00): Idle Smoothness Control / Cylinder #5 Quantity Deficit at Idle —>

<!— 2FF0EE (0x2FF0EE 0x00): EGR System Parametrization Failure —>

<!— 2FF3EE (0x2FF3EE 0x00): Test MU2 for similiar Conditions —>

<!— 2FF3FF (0x2FF3FF 0x00): MU_FMM_AS_TT_TEST2 —>

<!— 300402 (0x300402 0x00): MU_AM_JB1_SPORADIC_ERR —>

<!— 300403 (0x300403 0x00): Jake Brake Stage 1 Circuit Failed High —>

<!— 300404 (0x300404 0x00): Jake Brake Stage 1 Circuit Failed Low —>

<!— 300405 (0x300405 0x00): Jake Brake Stage 1 Circuit Failed Open —>

<!— 300407 (0x300407 0x00): ENGINE BRAKE SYSTEM SHOWS BRAKE LASHES —>

<!— 30050A (0x30050A 0x00): Detection of Misfire on cylinder 6 when misfire rate is above 5% —>

<!— 30050B (0x30050B 0x00): Cylinder #6 Misfire Detected —>

<!— 30050E (0x30050E 0x00): Idle Smoothness Control / Cylinder #6 Quantity Excess at Idle —>

<!— 30051F (0x30051F 0x00): Idle Smoothness Control / Cylinder #6 Quantity Deficit at Idle —>

<!— 30F0E8 (0x30F0E8 0x00): Intermittent Connection in Sensor Electric Circuit 3 —>

<!— 310402 (0x310402 0x00): MU_AM_JB2_SPORADIC_ERR —>

<!— 310403 (0x310403 0x00): Jake Brake Stage 2 Circuit Failed High —>

<!— 310404 (0x310404 0x00): Jake Brake Stage 2 Circuit Failed Low —>

<!— 310405 (0x310405 0x00): Jake Brake Stage 2 Circuit Failed Open —>

<!— 31050B (0x31050B 0x00): Cylinder #7 Misfire Detected —>

<!— 31050E (0x31050E 0x00): Idle Smoothness Control / Cylinder #7 Quantity Excess at Idle —>

<!— 31051F (0x31051F 0x00): Idle Smoothness Control / Cylinder #7 Quantity Deficit at Idle —>

<!— 31F0E8 (0x31F0E8 0x00): Intermittent Connection in Sensor Electric Circuit 4 —>

<!— 31F3FF (0x31F3FF 0x00): MU_EPF_DAMPER_TRQ_DERATE —>

<!— 32050B (0x32050B 0x00): Cylinder #8 Misfire Detected —>

<!— 32050E (0x32050E 0x00): Idle Smoothness Control / Cylinder #8 Quantity Excess at Idle —>

<!— 32051F (0x32051F 0x00): Idle Smoothness Control / Cylinder #8 Quantity Deficit at Idle —>

<!— 32F0E3 (0x32F0E3 0x00): O2 Sensor Circuit Bank 1 Sensor 1, Short Circuit —>

<!— 32F3E0 (0x32F3E0 0x00): injection quantity deficit detected —>

<!— 32F3E1 (0x32F3E1 0x00): injection quantity excess detected —>

<!— 330002 (0x330002 0x00): Intake Throttle Position Deviation Error —>

<!— 330003 (0x330003 0x00): Intake Air Throttle Circuit Failed High —>

<!— 330004 (0x330004 0x00): Intake Air Throttle Circuit Failed Low —>

<!— 33000A (0x33000A 0x00): Intake Throttle Position Deviation Error —>

<!— 330012 (0x330012 0x00): Intake Throttle Position Rationality Error —>

<!— 33F0E5 (0x33F0E5 0x00): O2 Sensor Circuit Bank 1 Sensor 1, Open Circuit on Line Vg —>

<!— 33F0E9 (0x33F0E9 0x00): MU_EGCP_DIA_SPI_WR_ERR —>

<!— 33F0EB (0x33F0EB 0x00): MU_EGCP_DIA_SPI_INI_ERR —>

<!— 33F3E0 (0x33F3E0 0x00): MU_EGR_LMBD_DEV_SRH —>

<!— 33F3E1 (0x33F3E1 0x00): MU_EGR_LMBD_DEV_SRL —>

<!— 34F0E5 (0x34F0E5 0x00): O2 Sensor Circuit Bank 1 Sensor 1, Open Circuit on Line Vip —>

<!— 34F3E1 (0x34F3E1 0x00): MU_RC4_P_INT_DEV_LOW_FR —>

<!— 350403 (0x350403 0x00): Quantity Control Valve (Low Side) Error —>

<!— 350404 (0x350404 0x00): Quantity Control Valve (High Side) Error —>

<!— 350405 (0x350405 0x00): Quantity Control Valve Error, Current too Low —>

<!— 350406 (0x350406 0x00): Quantity Control Valve, Desired Current Doesn’t Match Actual Current —>

<!— 35040E (0x35040E 0x00): Leakage in High Pressure Fuel System too High (Leak Down Test) —>

<!— 35F0E5 (0x35F0E5 0x00): O2 Sensor Circuit Bank 1 Sensor 1, Open Circuit on Line Vrc —>

<!— 35F3FF (0x35F3FF 0x00): Asymmetric injection mode expected —>

<!— 36F0E0 (0x36F0E0 0x00): MU_PBS_INTERNAL_ERROR —>

<!— 36F0E1 (0x36F0E1 0x00): MU_PBS_CRITICAL_ERROR —>

<!— 36F0E2 (0x36F0E2 0x00): MU_PBS_AIR_SUPPLY_ERR —>

<!— 36F0E3 (0x36F0E3 0x00): MU_PBS_U_BAT_HIGH —>

<!— 36F0E4 (0x36F0E4 0x00): MU_PBS_U_BAT_LOW —>

<!— 36F0E9 (0x36F0E9 0x00): MU_PBS_CAN_ERROR —>

<!— 36F0ED (0x36F0ED 0x00): MU_PBS_CONF_ERR —>

<!— 36F0EE (0x36F0EE 0x00): MU_PBS_SW_CHECK_ERR —>

<!— 36F0EF (0x36F0EF 0x00): MU_PBS_TEMP_ERROR —>

<!— 36F0F0 (0x36F0F0 0x00): MU_PBS_PAR_ERROR —>

<!— 36F3FF (0x36F3FF 0x00): Symmetric injection mode expected —>

<!— 38F0E0 (0x38F0E0 0x00): Classic Immobilizer, Number of Keys Limited to 8 —>

<!— 38F0E1 (0x38F0E1 0x00): Classic Immobilizer, Counter Overflow —>

<!— 38F0E2 (0x38F0E2 0x00): Classic Immobilizer, X5 Cancelled —>

<!— 38F0E3 (0x38F0E3 0x00): Classic Immobilizer, No TPC via CAN —>

<!— 38F0E4 (0x38F0E4 0x00): Classic Immobilizer, No TPC via Starter Pin —>

<!— 38F0E5 (0x38F0E5 0x00): Classic Immobilizer, Code Valid But False —>

<!— 38F0E6 (0x38F0E6 0x00): Injection Inhibited by Immobilizer (Wrong Key or CAN or EIS Issue) —>

<!— 3AF3E0 (0x3AF3E0 0x00): MU_RC4_T_GRP1_RANGE —>

<!— 3BF0E3 (0x3BF0E3 0x00): PCV High Side Short-Circuit to Battery —>

<!— 3BF0E4 (0x3BF0E4 0x00): Pressure Control Valve (High Side) Error —>

<!— 3BF3E0 (0x3BF3E0 0x00): MU_RC4_T_GRP2_RANGE —>

<!— 3CF0E3 (0x3CF0E3 0x00): Pressure Control Valve (Low Side) Error —>

<!— 3CF0E4 (0x3CF0E4 0x00): PCV Low Side Short-Circuit to Ground —>

<!— 3CF3E0 (0x3CF3E0 0x00): MU_RC4_T_GRP3_RANGE —>

<!— 3DF0EE (0x3DF0EE 0x00): Software Reset Detected —>

<!— 3DF0FF (0x3DF0FF 0x00): Software Reset Detected —>

<!— 3DF3FF (0x3DF3FF 0x00): MU_EHM_EOP_BUILDUP_CTR —>

<!— 3EF0FF (0x3EF0FF 0x00): MU_CPC_32 —>

<!— 3EF3FF (0x3EF3FF 0x00): nozzle begin data 1 out of range —>

<!— 3FF0FF (0x3FF0FF 0x00): MU_CPC_33 —>

<!— 3FF3FF (0x3FF3FF 0x00): nozzle begin data 2 out of range —>

<!— 40F0FF (0x40F0FF 0x00): MU_CPC_34 —>

<!— 40F3FF (0x40F3FF 0x00): current duration trim data out of range —>

<!— 41F0FF (0x41F0FF 0x00): MU_EPF_BROKEN_BELT_DETECT —>

<!— 41F3E9 (0x41F3E9 0x00): MU_CAN_MON_RCM_CAN_NO_COM —>

<!— 42F0EE (0x42F0EE 0x00): MU_TSA_BRK_FAIL_ON_BANK1 —>

<!— 42F0FF (0x42F0FF 0x00): MU_TSA_BRK_FAIL_BANK1 —>

<!— 42F3E9 (0x42F3E9 0x00): MU_CAN_MON_IPPC_CAN_NO_COM —>

<!— 43F0EE (0x43F0EE 0x00): MU_TSA_BRK_FAIL_ON_BANK2 —>

<!— 43F0FF (0x43F0FF 0x00): MU_TSA_BRK_FAIL_BANK2 —>

<!— 43F3E9 (0x43F3E9 0x00): MU_CAN_MON_SRA3_CAN_NO_COM —>

<!— 441501 (0x441501 0x00): Engine Crankcase Breather Oil Separator Speed too Low —>

<!— 450A02 (0x450A02 0x00): Turbo Charger Compressor Outlet Tempemperature Sensor, General Temperature Plausibility Error —>

<!— 450A03 (0x450A03 0x00): Turbo Charger Compressor Outlet Temperature Circuit Failed High —>

<!— 450A04 (0x450A04 0x00): Turbo Charger Compressor Outlet Temperature Circuit Failed Low —>

<!— 450A0A (0x450A0A 0x00): MU_ISP_T_COMP_OUT_GRAD —>

<!— 450A14 (0x450A14 0x00): Turbo Charger Out Temperature, Temperature too High (Low Box) —>

<!— 450A15 (0x450A15 0x00): Turbo Charger Out Temperature, Temperature too Low (High Box) —>

<!— 450A1F (0x450A1F 0x00): MU_RC4_T_COMP_OUT_GEN2 —>

<!— 45F0FF (0x45F0FF 0x00): Speed Limitation Fault —>

<!— 45F3E9 (0x45F3E9 0x00): SMART REMOTE ACTUATOR 3 (EGR), SIGNAL NOT VALID —>

<!— 460002 (0x460002 0x00): J1939 Park Brake Switch Signal from Source #1 is Erratic —>

<!— 460009 (0x460009 0x00): J1939 Park Brake Switch Signal from Source #2 is Missing —>

<!— 46000A (0x46000A 0x00): J1939 Park Brake Switch Signal from Source #3 is Erratic —>

<!— 46000D (0x46000D 0x00): J1939 Park Brake Switch Signal from Source #1 is Missing —>

<!— 46000E (0x46000E 0x00): J1939 Park Brake Switch Signal from Source #3 is Missing —>

<!— 460013 (0x460013 0x00): J1939 Park Brake Switch Signal from Source #2 is Erratic —>

<!— 460A02 (0x460A02 0x00): Difference Intake Manifold and Icooler Temperature Out Less Than Threshold (High Box) —>

<!— 460A03 (0x460A03 0x00): Charge Air Cooler Outlet Temperature Circuit Failed High —>

<!— 460A04 (0x460A04 0x00): Charge Air Cooler Outlet Temperature Circuit Failed Low —>

<!— 460A0A (0x460A0A 0x00): MU_ISP_T_ICOOLER_OUT_GRAD —>

<!— 460A0B (0x460A0B 0x00): Charge Air Cooler Outlet Temperature Sensor Plausibility Error —>

<!— 460A0E (0x460A0E 0x00): MU_RC4_T_CHG_COOL_OUT_DRFT —>

<!— 460A0F (0x460A0F 0x00): Cooling Efficency of Icooler too Low —>

<!— 460A10 (0x460A10 0x00): Charge Air Cooler Performance Monitor —>

<!— 460A14 (0x460A14 0x00): Charge Air Outlet Temperature Drift (Low Box) —>

<!— 460A15 (0x460A15 0x00): Charge Air Outlet Temperature Drift (High Box) —>

<!— 460A1F (0x460A1F 0x00): MU_RC4_T_ICOOLER_OUT_GEN2 —>

<!— 46F0E9 (0x46F0E9 0x00): FBS3 Injection Inhibit due to Keyline Lock —>

<!— 46F0EA (0x46F0EA 0x00): FBS3 Injection Inhibit due to Wrong Key —>

<!— 46F0EB (0x46F0EB 0x00): FBS3 Injection Inhibit due to Transport Protection —>

<!— 46F0ED (0x46F0ED 0x00): FBS3 Injection Inhibit due to Expired Prelease Time without Authentification —>

<!— 46F0EE (0x46F0EE 0x00): FBS3 Injection Inhibit due to Expired Prelease Time Mulitple Times (CAN or EIS Failure) —>

<!— 46F0EF (0x46F0EF 0x00): FBS3 Injection Inhibit due to Odometer Lock Function —>

<!— 46F0F0 (0x46F0F0 0x00): MU_IMB_FBS_HASH_CYC_HIGH —>

<!— 46F0F3 (0x46F0F3 0x00): FBS3 Injection Inhibit due to Missing EIS CAN Signales —>

<!— 46F0F5 (0x46F0F5 0x00): FBS3 t_count Value Expired —>

<!— 46F0FF (0x46F0FF 0x00): FBS3 Data Flash Defect, Exchange ECU —>

<!— 46F3E9 (0x46F3E9 0x00): SMART REMOTE ACTUATOR 3 (EGR), COMMUNICATION ERROR —>

<!— 47050E (0x47050E 0x00): Air Compressor Clutch —>

<!— 470A01 (0x470A01 0x00): Low Air Flow —>

<!— 470A02 (0x470A02 0x00): Turbo Charger / Super Charger Boost System Performance —>

<!— 470A03 (0x470A03 0x00): Charge Air Cooler Outlet Pressure Circuit Failed High —>

<!— 470A04 (0x470A04 0x00): Charge Air Cooler Outlet Pressure Circuit Failed Low —>

<!— 470A0E (0x470A0E 0x00): Charge Air Control, Pressure Not Plausible in Brake Mode —>

<!— 470A0F (0x470A0F 0x00): MU_SMOKE_MODE_TOO_FREQ —>

<!— 470A14 (0x470A14 0x00): Intake Manifold Pressure Plausibility (Low Box) —>

<!— 470A15 (0x470A15 0x00): Intake Manifold Pressure Plausibility Error, Pressure too Low (High Box) —>

<!— 47F0E3 (0x47F0E3 0x00): MU_PBS_THRO_ENG_SC_BATT —>

<!— 47F0E4 (0x47F0E4 0x00): MU_PBS_THRO_ENG_SC_GND —>

<!— 47F0E5 (0x47F0E5 0x00): MU_PBS_THRO_ENG_OL —>

<!— 47F3F0 (0x47F3F0 0x00): FUEL RAIL PRESSURE TOO LOW —>

<!— 47F3F2 (0x47F3F2 0x00): FUEL RAIL/SYSTEM PRESSURE — TOO HIGH —>

<!— 48F0E2 (0x48F0E2 0x00): MU_PBS_P_OUT_DEV —>

<!— 48F3E2 (0x48F3E2 0x00): RAIL PRESSURE FUEL TRIM LOWER LIMIT —>

<!— 48F3EA (0x48F3EA 0x00): UNDERCAPACITY IN HIGH PRESSURE CIRCUIT —>

<!— 49F0E2 (0x49F0E2 0x00): MU_PBS_P_IN_DEV —>

<!— 49F3E3 (0x49F3E3 0x00): WATER-DRAIN-MODULE — VENTIL 2 CIRCUIT FAILED HIGH —>

<!— 49F3E4 (0x49F3E4 0x00): WATER-DRAIN-MODULE — VENTIL 2 CIRCUIT FAILED LOW —>

<!— 49F3E5 (0x49F3E5 0x00): WATER-DRAIN-MODULE — VENTIL 2 CIRCUIT OPEN —>

<!— 4AF0E0 (0x4AF0E0 0x00): MU_PV_B_SHDOWN_OVERVOLTAGE —>

<!— 4AF3E0 (0x4AF3E0 0x00): WATER-DRAIN-MODULE: FUEL PRESSURE SENSOR TOO HIGH —>

<!— 4AF3E3 (0x4AF3E3 0x00): LOW SIDE WATER-DRAIM-MODULE FUEL PRESSURE SENSOR CIRCUIT FAILED HIGH —>

<!— 4AF3E4 (0x4AF3E4 0x00): LOW SIDE WATER-DRAIM-MODULE FUEL PRESSURE SENSOR CIRCUIT FAILED LOW —>

<!— 4B0E03 (0x4B0E03 0x00): Injector Cylinder #1 Spill Control Valve («Amplifier»), Abnormal Operation (MAX) —>

<!— 4B0E04 (0x4B0E04 0x00): Injector Cylinder #1 Spill Control Valve («Amplifier»), Abnormal Operation (MIN) —>

<!— 4B0E05 (0x4B0E05 0x00): Injector Cylinder #1 Spill Control Valve («Amplifier»), Circuit Open —>

<!— 4B0E06 (0x4B0E06 0x00): Injector Cylinder #1 Spill Control Valve («Amplifier»), Valve Shorted Circuit —>

<!— 4B0E0A (0x4B0E0A 0x00): Injector Cylinder #1 Spill Control Valve («Amplifier»), Abnormal Rate of Change —>

<!— 4BF0E2 (0x4BF0E2 0x00): CPC Clock Data Invalid —>

<!— 4BF0EA (0x4BF0EA 0x00): MU_ISP_MCM_TIME_RAT_ERROR —>

<!— 4BF0EF (0x4BF0EF 0x00): MCM Engine Run Timer Plausibility —>

<!— 4BF0F1 (0x4BF0F1 0x00): MCM Engine Off Timer Plausibility —>

<!— 4BF0F2 (0x4BF0F2 0x00): MU_IS4_RTC_ENG_OFF_RAT_CHK —>

<!— 4BF0F3 (0x4BF0F3 0x00): MU_CPC_CLOCK_DATA_SNA —>

<!— 4BF3F0 (0x4BF3F0 0x00): WATER-DRAIN-MODULE : RESTRICTION ON VENTIL 1 DETECTED —>

<!— 4BF3F2 (0x4BF3F2 0x00): WATER-DRAIN-MODULE : LEAKAGE ON VENTIL 1 DETECTED —>

<!— 4C0E03 (0x4C0E03 0x00): Injector Cylinder #2 Spill Control Valve («Amplifier»), Abnormal Operation (MAX) —>

<!— 4C0E04 (0x4C0E04 0x00): Injector Cylinder #2 Spill Control Valve («Amplifier»), Abnormal Operation (MIN) —>

<!— 4C0E05 (0x4C0E05 0x00): Injector Cylinder #2 Spill Control Valve («Amplifier»), Circuit Open —>

<!— 4C0E06 (0x4C0E06 0x00): Injector Cylinder #2 Spill Control Valve («Amplifier»), Valve Shorted Circuit —>

<!— 4C0E0A (0x4C0E0A 0x00): Injector Cylinder #2 Spill Control Valve («Amplifier»), Abnormal Rate of Change —>

<!— 4CF0F0 (0x4CF0F0 0x00): Fuel Rail Pressure Too Low, Similar Condition —>

<!— 4CF0F2 (0x4CF0F2 0x00): Fuel Rail Pressure Too High, Similar Condition —>

<!— 4CF3F0 (0x4CF3F0 0x00): WATER-DRAIN-MODULE : RESTRICTION VENTIL 2 DETECTED —>

<!— 4CF3F2 (0x4CF3F2 0x00): WATER-DRAIN-MODULE : LEAKAGE ON VENTIL 2 DETECTED —>

<!— 4D0E03 (0x4D0E03 0x00): Injector Cylinder #3 Spill Control Valve («Amplifier»), Abnormal Operation (MAX) —>

<!— 4D0E04 (0x4D0E04 0x00): Injector Cylinder #3 Spill Control Valve («Amplifier»), Abnormal Operation (MIN) —>

<!— 4D0E05 (0x4D0E05 0x00): Injector Cylinder #3 Spill Control Valve («Amplifier»), Circuit Open —>

<!— 4D0E06 (0x4D0E06 0x00): Injector Cylinder #3 Spill Control Valve («Amplifier»), Valve Shorted Circuit —>

<!— 4D0E0A (0x4D0E0A 0x00): Injector Cylinder #3 Spill Control Valve («Amplifier»), Abnormal Rate of Change —>

<!— 4DF0E2 (0x4DF0E2 0x00): Over capacity in High Pressure Circuit, Similar Condition —>

<!— 4DF0EA (0x4DF0EA 0x00): Under capacity in High Pressure Circuit, Similar Condition —>

<!— 4DF3FF (0x4DF3FF 0x00): WATER-DRAIN-MODULE: EMULSION DETECTED —>

<!— 4E0E03 (0x4E0E03 0x00): Injector Cylinder #4 Spill Control Valve («Amplifier»), Abnormal Operation (MAX) —>

<!— 4E0E04 (0x4E0E04 0x00): Injector Cylinder #4 Spill Control Valve («Amplifier»), Abnormal Operation (MIN) —>

<!— 4E0E05 (0x4E0E05 0x00): Injector Cylinder #4 Spill Control Valve («Amplifier»), Circuit Open —>

<!— 4E0E06 (0x4E0E06 0x00): Injector Cylinder #4 Spill Control Valve («Amplifier»), Valve Shorted Circuit —>

<!— 4E0E0A (0x4E0E0A 0x00): Injector Cylinder #4 Spill Control Valve («Amplifier»), Abnormal Rate of Change —>

<!— 4EF0E7 (0x4EF0E7 0x00): Classic Immobilizer, Key Slip Detected —>

<!— 4EF3FF (0x4EF3FF 0x00): WATERPUMP DOESN’T SLOW DOWN —>

<!— 4F0E03 (0x4F0E03 0x00): Injector Cylinder #5 Spill Control Valve («Amplifier»), Abnormal Operation (MAX) —>

<!— 4F0E04 (0x4F0E04 0x00): Injector Cylinder #5 Spill Control Valve («Amplifier»), Abnormal Operation (MIN) —>

<!— 4F0E05 (0x4F0E05 0x00): Injector Cylinder #5 Spill Control Valve («Amplifier»), Circuit Open —>

<!— 4F0E06 (0x4F0E06 0x00): Injector Cylinder #5 Spill Control Valve («Amplifier»), Valve Shorted Circuit —>

<!— 4F0E0A (0x4F0E0A 0x00): Injector Cylinder #5 Spill Control Valve («Amplifier»), Abnormal Rate of Change —>

<!— 4FF0EB (0x4FF0EB 0x00): Cylinder #1 Misfire Detected, Similar Condition —>

<!— 4FF3F0 (0x4FF3F0 0x00): EXHAUST GAS RECIRCULATION «A» CONTROL CIRCUIT RANGE/PERFORMANCE HIGH —>

<!— 4FF3F2 (0x4FF3F2 0x00): EXHAUST GAS RECIRCULATION «A» CONTROL CIRCUIT RANGE/PERFORMANCE HIGH —>