A0703 micromaster ошибка

Интересное на сайте
Инженерный опыт
Полезные ссылки

• Все о Simoreg DC Master
• Принцип работы рекуператора
• Оборудование для сети Wi-Fi

Коды ошибок преобразователя Микромастер 440*

*Нажав на код интересующей Вас аварии, Вы перейдете на страницу с ее подробным описанием (функция в стадии наладки).

18 декабря 2008 г. — добавлены описания сообщений F0001 и A0501.

19 декабря 2008 г. — добавлено краткое описание сбоя F0002.

12 января 2009 г. — добавлено описание сбоев F0003 и F0004.

15 января 2009 г. — добавлено полное описание сбоя F0002.

21 января 2009 г. — в раздел «Статьи» добавлена статья «Функция компенсации скольжения в Микромастер 440»

• Форум Siemens

Литература по электроприводам
Справочные таблицы

Книги

• Класс защиты (IP)
• Класс изоляции
• Режимы работы двигателя (S)
• Допустимая длина кабеля для Micromaster

• Управление электроприводами. Башарин, Новиков, Соколовский
• Общий курс электропривода. Чиликин, Сандлер
• Ограничение динамических нагрузок электропривода. Ключев В. И.

Статьи
Документация по Micromaster (скачать)

• Компенсация скольжения в Micromaster440
• Электромагнитные помехи с ШИМ
• Расчет сетевого фильтра

другие статьи…

• Наладка Profibus
• GSD-файл
• Инструкция по эксплуатации Micromaster 440 (на русск. языке)

Issue 10/06

7.2

Fault

Significance

F0001

Overcurrent

F0002

Overvoltage

F0003

Undervoltage

F0004

Inverter Overtemperature

2

F0005

Inverter I

t

F0011

Motor Overtemperature I

F0012

Inverter temp. signal lost

F0015

Motor temperature signal lost

F0020

Mains Phase Missing

F0021

Earth fault

F0022

HW monitoring active

F0023

Output fault

F0024

Rectifier Over Temperature

F0030

Fan has failed

F0035

Auto restart after n

F0040

Automatic Calibration Failure

F0041

Motor Data Identification Failure

F0042

Speed Control Optimization Failure

F0051

Parameter EEPROM Fault

F0052

Power stack Fault

F0053

IO EEPROM Fault

F0054

Wrong IO Board

F0060

Asic Timeout

F0070

CB setpoint fault

F0071

USS (BOP link) setpoint fault

F0072

USS (COM link) setpoint fault

F0080

ADC lost input signal

F0085

External Fault

F0090

Encoder feedback loss

F0101

Stack Overflow

F0221

PID Feedback below min. value

F0222

PID Feedback above max. value

BIST Tests Failure

F0450

(Service mode only)

F0452

Belt Failure Detected

MICROMASTER 440

Operating Instructions (Compact)

Alarm

A0501

A0502

A0503

A0504

A0505

2

t

A0506

A0511

A0520

A0521

A0522

A0523

A0535

A0541

A0542

A0590

A0600

A0700 — CB warning 1

A0709

A0710

A0711

A0910

A0911

A0912

A0920

A0921

A0922

A0923

A0952

A0936

7 Displays and messages

Significance

Current Limit

Overvoltage limit

Undervoltage Limit

Inverter Overtemperature

2

Inverter I

t

Inverter Duty Cycle

2

Motor Overtemperature I

Rectifier Overtemperature

Ambient Overtemperature

I2C read out timeout

Output fault

Braking Resistor Hot

Motor Data Identification Active

Speed Control Optimization Active

Encoder feedback loss warning

RTOS Overrun Warning

CB warning 9

CB communication error

CB configuration error

Vdc-max controller de-activated

Vdc-max controller active

Vdc-min controller active

ADC parameters not set properly

DAC parameters not set properly

No load applied to inverter

Both JOG Left and Right are requested

Belt Failure Detected

PID Autotuning Active

t

77

F0001
OverCurrent
— Motor power (P0307) does not correspond to the inverter power (r0206)
— Motor lead short circuit
— Earth faults
Check the following:
1. Motor power (P0307) must correspond to inverter power (r0206).
2. Cable length limits must not be exceeded.
3. Motor cable and motor must have no shortcircuits or earth faults
4. Motor parameters must match the motor in use
5. Value of stator resistance (P0350) must be correct
6. Motor must not be obstructed or overloaded
— Increase the ramp time
— Reduce the boost level
OFF2

F0002
OverVoltage
— DC-link voltage (r0026) exceeds trip level (P2172)
— Overvoltage can be caused either by too high main supply voltage or if motor is in regenerative mode. Regenerative mode can be cause by fast ramp downs or if the motor is driven from an active load.
Check the following:
1. Supply voltage (P0210) must lie within limits indicated on rating plate .
2. DC-link voltage controller must be enabled (P1240) and parameterized properly.
3. Ramp-down time (P1121) must match inertia of load.
4. Required braking power must lie within specified limits.
NOTE:
Higher inertia requires longer ramp times; otherwise, apply braking resistor.
OFF2

F0003
UnderVoltage
— Main supply failed.
— Shock load outside specified limits.
Check the following:
1. Supply voltage (P0210) must lie within limits indicated on rating plate.
2. Supply must not be susceptible to temporary failures or voltage reductions.
OFF2

F0004
Inverter Over
Temperature
— Inverter overloaded.
— Duty cycle too demanding.
— Motor power (P0307) exceeds inverter power capability (r0206).
Check the following:
1. Load duty cycle must lie within specified limits.
2. Motor power (P0307) must match inverter power (r0206)
OFF2

F0011
Motor Over
Temperature
— Motor overloaded
Check the following:
1. Load duty cycle must be correct
2. Motor nominal overtemperatures (P0626-P0628) must be correct
3. Motor temperature warning level (P0604) must match
OFF1

F0012
Inverter temp.
signal lost
Wire breakage of inverter temperature (heatsink) sensor

OFF2

F0015
Motor temperature
signal lost
Open or short circuit of motor temperature sensor. If signal loss is detected, temperature monitoring switches over to monitoring with the motor thermal model.

OFF2

F0020
Mains Phase
Missing
Fault occurs if one of the three input phases are missed and the pulses are enabled and drive is loaded
Check the input wiring of the mains phases
OFF2

F0021
Earth fault
Fault occurs if the sum of the phase currents is higher than 5 % of the nominal inverter current.
NOTE — Framesizes D to F
This fault only occurs on inverters that have 3 current sensors.

OFF2

F0022
Powerstack fault
That hardware fault (P0947 = 22 and
P0949 = 1) caused by the following events:
(1) DC-link overcurrent = short circuit of IGBT
(2) Short circuit of chopper
(3) Earth fault
(4) I/O board is not poperly inserted.
— Framesizes A to C (1),(2),(3),(4)
— Framesizes D to E (1),(2),(4)
— FramesizeF(2),(4)
— Since all these faults are assigned to one signal on the power stack, it is not possible to establish which one actually occurred.
— UCE failure was detected, when P0947 = 22 and fault value P0949 =12 or 13 or 14, depending on UCE (for MegaMaster only)
Check the I/O board. It has to be fully pressed home.
OFF2

F0023
Output fault
One phase of output is disconnected

OFF2

F0024
Rectifier Over
Temperature
— Ventilation inadequate
— Fan inoperative
— Ambient temperature is too high.
Check the following:
— Fan must turn when inverter is running
— Pulse frequency must be set to default value
— Ambient temperature could be higher than
specified for the inverter
OFF2

F0030
Fan has failed
Fan no longer working
— Fault cannot be masked while options module
(AOP or BOP) is connected.
— Need a new fan.
OFF2

F0035
Auto restart after n
Auto restart fault after n-restart try

OFF2

F0040
Automatic
Calibration Failure
MICROMASTER 440 only

OFF2

F0041
Motor Data
Identification
Failure
Motor data identification failed.
— Alarm value =0: Load missing
— Alarm value =1: Current limit level reached during identification.
— Alarm value =2: Identified stator resistance less than 0.1% or greater than 100%.
— Alarm value =3: Identified rotor resistance less than 0.1% or greater than 100%.
— Alarm value =4: Identified stator reactance less than 50% and greater than 500%
— Alarm value =5: Identified main reactance less than 50% and greater than 500%
— Alarm value =6: Identified rotor time constant less than 10ms or greater than 5s
— Alarm value =7: Identified total leakage reactance less than 5% and greater than 50%
— Alarm value =8: Identified stator leakage reactance less than 25% and greater than 250%
— Alarm value =9: Identified rotor leakage inductance less than 25% and greater than 250%
— Alarm value = 20: Identified IGBT onvoltage less than 0.5 or greater than 10V
— Alarm value = 30: Current controller at voltage limit
— Alarm value = 40: Inconsistence of identified data set, at least one
identification failed Percentage values based on the impedance Zb = Vmot,nom / sqrt(3) / Imot,nom
0: Check that the motor is connected to the inverter.
1-40: Check if motor data in P304-311 are correct. Check what type of motor wiring is required (star, delta).
OFF2

F0042
Speed Control
Optimisation Failure
— Motor data identification failed.
— Alarm value =0: Time out waiting for stable speed
— Alarm value =1: Inconsistent readings

OFF2

F0051
Parameter EEPROM
Fault
— Read or write failure while saving nonvolatile
parameter.
— Factory Reset and new parameterization
— Change drive
OFF2

F0052
power stack Fault
— Read failure for power stack information or invalid data
— Change drive
OFF2

F0053
IO Eeprom Fault
— Read failure for IO EEPROM information or invalid data.
— Check data
— Change IO module
OFF2

F0054
Wrong IO Board
1. Wrong IO board is connected.
2. No ID detected on IO board, No data.
— Check data
— Change IO module
OFF2

F0060
Asic Timeout
— Internal communications failure
— If fault persists, change inverter
OFF2

F0070
CB setpoint fault
— No setpoint values from CB (communication board) during telegram off time
— Check CB and communication partner
OFF2

F0071
USS (BOP-link)
setpoint fault
— No setpoint values from USS during telegram off time
— Check USS master
OFF2

F0072
USS (COMM link)
setpoint fault
— No setpoint values from USS during telegram off time
— Check USS master
OFF2

F0080
ADC lost input
signal
— Broken wire
— Signal out of limits

OFF2

F0085
External Fault
— External fault triggered via terminal inputs
— Disable terminal input for fault trigger.
OFF2

F0090
Encoder feedback
loss
— Signal from Encoder lost
1. Check encoder fitted. If encoder not fitted, set P400 = 0 and select SLVC mode (P1300 = 20 or 22)
2. Check connections between encoder and inverter
3. Check encoder not faulty (select P1300 = 0, run at fixed speed, check encoder feedback signal in P66)
Increase encoder loss threshold in P492
OFF2

F0101
Stack Overflow
— Software error or processor failure
— Run self test routines
OFF2

F0221
PID Feedback below
min. value
— PID Feedback below min. value P2268
— Change value of P2268.Adjust feedback gain.

F0222
PID Feedback above
max. value
— PID feedback above max. value P2267.
— Change value of P2267.Adjust feedback gain.

F0450
BIST Tests Failure
Fault value:
1. Some power section tests have failed
2. Some control board tests have failed
4. Some functional tests have failed
8. Some IO module tests have failed. (MM 420 only)
16. Internal RAM failed on power-up check
— Drive may run but some features will not work properly.
— Replace drive.

F0452
Belt Failure
Detected
— Load conditions on motor indicate belt
failure or mechanical fault.
Check the following:
1. No breakage, seizure or obstruction of drive train.
1. If using an external speed sensor, check for correct function.Check parameters:
— P0409 (pulse per min at rated speed).
— P2191 (Belt failure speed tolerance).
— P2192 (delay time for permitted deviation)
2. If using the torque envelope, check parameters:
— P2182 (threshold frequency f1)
— P2183 (threshold frequency f2)
— P2184 (threshold frequency f3)
— P2185 (upper torque threshold 1)
— P2186 (lower torque threshold 1)
— P2187 (upper torque threshold 2)
— P2188 (lower torque threshold 2)
— P2189 (upper torque threshold 3
— P2190 (lower torque threshold 3)
— P2192 (delay time for permitted deviation)
4. Apply lubrication if required.