Canon mf4320d ошибка e225

Модератор: vetal

Вернуться в Принтеры, МФУ, факсы, копиры формата A4

Кто сейчас на форуме

Сейчас этот форум просматривают: @rtцентр и гости: 45

Системный сбой или ошибка Е225, в первую очередь, появляется когда плата у форматтера Canon mf3228 выходит из строя. Если после того, как вы включили принтер, начинается тестирование принтера, но одновременно с этим линейка начинает мигать разными цветами, после чего на экране вы видите подобную ошибку, то можно догадаться, что это проблема с платой.

Из личного опыта могу сказать, что 3 свои принтеры я смог восстановить благодаря тому, что заменил эти платы. Сброс ошибки происходит автоматически после устранения причины.
Как один из вариантов системный сбой е225 Canon mf3228 может быть появится из за того, что возникло неисправность CIS-unit, т.е. самой линейки экспонирования, парт номер FK2-2869 (см. фото), кроме того причиной могут быть плохие контакты в разъемах или разрыв шлейфа сканера.
Системный сбой Canon 4018 e225

E225 — ошибка блока сканера. Сброс ошибки происходит автоматически после устранения проблемы.
На Canon 4018 ошибка e225 может возникнуть из-за плохого контакта шлейфа, из-за неисправности линейки экспонирования. Но чаще всего данная ошибка возникает при выходе из строя платы форматера.
Давайте доберемся до платы форматера.
Откройте панель управления (метка 1).
Откройте крышку картриджа (метка 2).
Выкрутите 2 винта (метка 3).
Отогните 2 защелки (метка 4) и снимите переднюю крышку (метка 5).
E225 — CIS lamp has a fault.
— Turn the power OFF and then back ON.
— Replase the CIS unit.

Тем имения проблема гласит о том что неисправность с линейкой экспонирования блока сканера. Надо ее заменить. Но часто ошибка е225 Canon mf4018 возникает при выходе из строя платы форматтера Canon mf 4018. Если линейка сканера мигает разными цветами, то скорее всего причина в этом. Сброс ошибки происходит автоматически после устранения причины.
Причиной ошибки E225 могут быть так же плохие контакты шлейфа в разъемах, разрыв шлейфа, или, конечно же, неисправность CIS-unit, т.е. самого блока лампы экспонирования.

Есть еще и иной способ устранения ошибки E225 на Canon mf 4018.
При ошибке E225 может сгорел или сел крен на 18 вольт, который находится рядом с гнездом подключения кабеля принтера с компьютером, вот его то и нужно заменить.
Если у Вас ничего не получилось с ремонтом мфу Canon 4018 вы можете написать нам чуть ниже коментарий а мы со своей стороны поможем Вам решить вашу неисправность.

E225 — ошибка блока сканера.

Сброс ошибки происходит автоматически после устранения проблемы.
Ошибка может возникнуть из-за плохого контакта шлейфа, из-за неисправности линейки экспонирования. Но чаще всего данная ошибка возникает при выходе из строя платы форматера.

Давайте доберемся до платы форматера.

Откройте панель управления (метка 1).
Откройте крышку картриджа (метка 2).
Выкрутите 2 винта (метка 3).
Отогните 2 защелки (метка 4) и снимите переднюю крышку (метка 5).

 Коды ошибок:

Системные ошибки
E198 — Flash ROM write error (ошибка записи ROM)
E674 — Modem error (ошибка модема)

Ошибка сканера
E225 — CIS lamp has a fault (неисправность лампы CIS)

Ошибки принтера
E000 — The High-voltage PCB has a fault (неисправность платы PCB)
E100 — The scanner assembly has a fault (неисправность узла сканера)

Коммуникационные ошибки
0001 — Nothing G3 signal received within 35 sec (потеря сигнала G3 в течение 35 секунд)
0003 — Received DIS after sending DIS signal
0004 — Received DCN after sending DTC signal
0009 — Can’t receive any signal within 35 sec. in manual polling mode (невозможно принять сигнал в течение 35 секунд в ручном режиме)
0010 — Received DCN signal after sending DTC signal in Polling Rx
0011 — Can’t receive any correct response after sending DTC signal (невозможно принять правильный ответ после отправки сигнала DTC)
0012 — Remote side Password not match in Polling Rx/our side no any file to be polling
0013 — Can’t receive carrier within 6 sec. after sending CFR in date phase C
0014 — Can’t receive T.30 signal after sending FTT signal (невозможно принять сигнал T.30)
0016 — Receive DCN signal after sending PTT signal
0017 — Can’t receive any response from remote side after sending DIS
0018 — Can’t detect energy within 6 sec after sending FTT command
0019 — Received DCN signal sending CFR signal
001A — No energy on line over 6 sec. within phase C before any corrected ECM frame
001D — Can’t detect flag after sending CFR signal
001E — Timeout in V.17 ECM Rx phase C
0020 — Can’t correct frame within 6 sec at phase C
0021 — File full.
0022 — Owing to noise interference on the line, receiving side can’t receive correct data within specified time (no ECM)
0023 — Can’t receive correct signal after sending CFR signal
0030 — Can’t receive any signal within 6 sec. At phase D
0031 — Received incorrect signal at phase D (not EOP, MPS, EOM, DCN, PPS_Q, PPS_Q,etc)
0032 — Can’t receive carrier within 6 sec after sending MCF or RTP, RTN signal
0033 — Received DCN signal at ohase D within pages (not last page)
0039 — In non_ECM mode, when machine alredy received the data dosen’t receive 13.1 seconds
001F — Can’t detect any G3 signal within 35 sec after sending DTC signal
003F — Remote side TSI not define in machine one touch or speed dial directory
0040 — Can’t receive carrier within 6 sec. after sending CTR
0041 — Can’t receive carrier within 6 sec. after sending PPR
0042 — Can’t receive correct signal after sending RNR signal
0043 — Receive incorrect signal at phase D in ECM mode
0044 — Can’t receive carrier/FSK signal within 6 sec. After sending MCF. ln ECM mode.
0047 — Can’t receive correct signal or DCN received after sending ERR signal.
0048 — Can’t receive correct signal after receive PPS_PRI_Q
004B — Can’t detect correct FSK signal even through detected FSK tone within 6 sec.
004C — Handshake fail during re-train or between page in V34 Rx
004E — Receive DCN signal after sending DIS in V.34
004F — Remote side disconnected after sending ANSam in V.8 phase
0050 — Can’t receive any correct signal after detected CJ signal in V.8 phase
0051 — Can’t receive phase 3 signal after phase 2 within 20 seconds in V.34
0053 — Modem disconnect after phase 4 in V.34
0054 — Remote side disconnect after phase 4 in V.8
0055 — Receive incorrect signal after sending DIS signal in V.34
0056 — Modem disconnect after sending CFR in V.34
0058 — Can’t detect image signal within 6 sec after modem enter to primary phase in V.34
005A — Modem cannot detect any correct ECM frame with 3 minutes in phase C
005B — Modem can’t detect control channel with 12 sec in phase C
005C — Detect busy tone within control channel after phase C
005D — Modem can’t detect any correct ECM frame with 12 sec in phase C
005E — Can’t detect control channel signal after received RCP frame within 6 sec
005F — Can’t detect silence after sending JM signal for polling TX function
0060 — There are no any bullietin files to be polled in V.34
0061 — Machine cannot detect V.21 or V.8 signal with 35 sec
0062 — Modem disconnect in phase D after our side sending out flags sequence in control channel
0063 — Can’t receive any flag sequence in control channel within 25 sec in phase D
0064 — Can’t detect any control channel signal in phase D within 60 sec even through energy still on the line
0065 — Can’t detect any control channel signal within 60 sec after detect sillence in phase D
0066 — Can’t receive T.30 signal or carrier after sending CFR in V.34
0069 — Capability no match paper size after received is DCS signal
0070 — User press stop key within receiving
0071 — Memory full within receiving
0080 — Can’t detect any G3 signal within 35 sec. specified by ITU-T in phase B
0081 — Received DTC signal in transmission phase
0082 — Transmitting unit receives a signal other than DIS or DTC. And DCN in phase B
0083 — Detected FSK signal, but Can’t receive any signal within 35 sec
0084 — Detect DCN signal in phase B
0085 — Transmitting unit sending DCS 3 times consecutively, but each time responds with DIS/DTC
0086 — Detected responds signal other than DTC,DIS,FTT,DCN or CFR after sending DCS
0087 — Training attempt has failed because speed unit can’t adjust to low lower speed
0088 — Received DCN signal after sending out DCS signal
008B — Receivers protcol of DIS is received, but it is not compatible with our machine
008C — Remote side or our side not support capability
008D — Receivers protocol of DIS is received, but remote side can’t receive document temporary, may because by run out of paper or other reason
008F — Modem not ready to received V.34 data within 6 sec after received CFR signal
0090 — Called side document not ready for our polling
0091 — Can’t receive any commabd after send DCN signal 3 times consecutively
0093 — Received DCN signal after sending out DCN signal
0094 — Time out during transmit ECM frame or RCP command
0095 — Wrong ID number
0096 — SUBADDRESS/PASSWORD capability not match in polling Rx mode
009A — Can’t detect any signal after sending CI signal.
009D — Remote side hang up before V.34 modem enter phase 2 state in V.34 polling Rx
009E — Manual Tx over 15 minutes whin in phase C by non-ECM mode
00A0 — User stop or cancel transmission job
00A1 — Document JAM within transmission
00AE — Can’t finished V.8 procedure or detect V.21 signal after CM signal
00AF — Modem can’t enter into control channel after TX side sending out RCP signal
for V34
00B1 — Can’t finish V.8 procedure or detect V.21 signal after ANSam signal within 35 sec
00B2 — Can’t detect phase 2 signal after our side sending CJ signal within 30 sec
00B3 — Can’t detect correct V.21 or JM signal after sending CM or CJ signal
00B4 — Can’t detect correct phase 2 signal within 25 second after CM/JM signal exchange
00B5 — Can’t detect phase 3 signal after Phase 2
00B6 — Can’t detect phase 4 signal within 25 sec after CM/JM exchange
00B8 — Remote side disconnect after our side sending DCS signal in V.34
00BA — Cannot received correct signal after our side sending DTC signal in V.34
00BB — Every time our side received DIS signal after sending DTC in V.34
00BC — Modem can’t ready within 10 second after entering primary channel in V.34
00BD — Can’t detect correct V.21 or JM signal after detected FSK frequency
00BE — Remote side no document to be polled after V.8 handshaking
00BF — Capability no match after V.8 handshaking
00C1 — At phase-D, transmitting units out EOP 3 times consecutively, but receive no answer from receiving unit
00C2 — Remote side disconnect after sending out V.8 CM signal
00C4 — After sending MPS signal, the received is not one of MCF, RTN, PIP, PIN, RTP, DCN
00C5 — Received DCN signal after sending MPS signal
00C9 — At phase D, sending MPS 3 times consecutively, but no answer from receiveing unit
00CA — After sending EOP signal, the received is not one of MCF, RTN, PIP, PIN, PRI-EOP, DCN, RTP.
00CB — After sending EOP signal, the received is DCN signal
00CF — Received incorrect signal after sending DTC signal for V.34 polling
00D0 — Received ERR signal after sending EOR_NULL
00D1 — Received incorrect response after sending PPS_EOP signal
00D2 — Received DCN after sending PPS_EOP signal
00D3 — Received DCN after sending PPS_NULL signal
00D8 — Can’t detect correct phase 3 signal for poling
00D9 — Can’t detect correct phase 3 signal after detect silence after phase 2
00DA — Can’t detect phase 4 signal within 30 sec
00DB — Can’t received any T.30 signal within 30 sec within phase 4
00DC — Received T.30 signal in phase 4 other than DCS, DIS or DTC
00DE — Remote side no SUB capability
00E0 — At phase-D, transmitting units out PPS_NULL 3 times consecutively but receive not answer
00E1 — Received incorrect response after sending PPS_NULL
00E2 — Can’t receive any response in RR response procedure after sending PPS_NULL
00E4 — At phase D, transmitting units out PPS_MPS 3 times consecutivery but receive no answer
00E5 — Received incorrect response after sending PPS_MPS signal
00E6 — Can’t receive any response in RR response procedure after sending PPS_MPS
00E7 — Reseived DCN after sending PPS_MPS
00E8 — At phase-D, transmitting units out PPS_EOP 3 times consecutively but receive no answer
00E9 — Receive PIN signal after sent last page data
00EA — Can’t receive any response in RR response procedure after sending PPS_EOP
00EE — At phase-D, transmitting units out EOR_NULL 3 times consecutively but receive no answer
00EF — Received incorrect response after sending EOR_NULL
00F0 — Can’t receive any response in RR response procedure after sending EOR_NULL
00F1 — At phasa-D, transmitting units out EOR_MPS 3 times consecutively but receive no answer
00F2 — Received incorrect response after sending EOR_MPS
00F3 — Received ERR signal after sending EOR_MPS
00F4 — Can’t receive any response in RR response procedure after sending EOR_MPS
00F5 — At phasa-D, transmitting units out EOR_EOP 3 times consecutively but receive no answer
00F6 — Received incorrect response after sending EOR_EOP
00F7 — After Received ERR, our side can’t received response after sending EOR_EOP command
00FC — Can’t receive any response after sending CTC
00FD — Can’t speed down to lower speed
00FE — Memory full for transmission
00FF — REDAIL ALL FAIL