| 0 |
PLEASE TURN OFF POWER |
| 1 |
TH PARITY ALARM |
| 2 |
TV PARITY ALARM |
| 3 |
TOO MANY DIGITS |
| 4 |
ADDRESS NOT FOUND |
| 5 |
NO DATA AFTER ADDRESS |
| 6 |
ILLEGAL USE OF NEGATIVE SIGN |
| 7 |
ILLEGAL USE OF DECIMAL POINT |
| 9 |
ILLEGAL ADDRESS INPUT |
| 10 |
IMPROPER G–CODE |
| 11 |
NO FEEDRATE COMMANDED |
| 14 |
CAN NOT COMMAND G95 (M series) |
| 14 |
ILLEGAL LEAD COMMAND (T series) |
| 15 |
TOO MANY AXES COMMANDED (M series) |
| 15 |
TOO MANY AXES COMMANDED (T series) |
| 20 |
OVER TOLERANCE OF RADIUS |
| 21 |
ILLEGAL PLANE AXIS COMMANDED |
| 22 |
NO CIRCLE RADIUS |
| 23 |
ILLEGAL RADIUS COMMAND (T series) |
| 25 |
CANNOT COMMAND F0 IN G02/G03 (M series) |
| 27 |
NO AXES COMMANDED IN G43/G44 (M series) |
| 28 |
ILLEGAL PLANE SELECT |
| 29 |
ILLEGAL OFFSET VALUE (M series) |
| 29 |
ILLEGAL OFFSET VALUE (T series) |
| 30 |
ILLEGAL OFFSET NUMBER (M series) |
| 30 |
ILLEGAL OFFSET NUMBER (T series) |
| 31 |
ILLEGAL P COMMAND IN G10 |
| 32 |
ILLEGAL OFFSET VALUE IN G10 |
| 33 |
NO SOLUTION AT CRC (M series) |
| 33 |
NO SOLUTION AT CRC (T series) |
| 34 |
NO CIRC ALLOWED IN ST–UP /EXT BLK (M series) |
| 34 |
NO CIRC ALLOWED IN ST–UP /EXT BLK (T series) |
| 35 |
CAN NOT COMMANDED G31 (T series) |
| 35 |
CAN NOT COMMANDED G39 (M series) |
| 36 |
CAN NOT COMMANDED G31 (M series) |
| 37 |
CAN NOT CHANGE PLANE IN CRC (M seires) |
| 37 |
CAN NOT CHANGE PLANE IN NRC (T seires) |
| 38 |
INTERFERENCE IN CIRCULAR BLOCK (M seires) |
| 38 |
INTERFERENCE IN CIRCULAR BLOCK (T series) |
| 39 |
CHF/CNR NOT ALLOWED IN NRC (T series) |
| 40 |
INTERFERENCE IN G90/G94 BLOCK (T series) |
| 41 |
INTERFERENCE IN CRC (M seires) |
| 41 |
INTERFERENCE IN NRC (T seires) |
| 42 |
G45/G48 NOT ALLOWED IN CRC (M series) |
| 44 |
G27–G30 NOT ALLOWED IN FIXED CYC (M series) |
| 45 |
ADDRESS Q NOT FOUND (G73/G83) (M series) |
| 46 |
ILLEGAL REFERENCE RETURN COMMAND |
| 47 |
ILLEGAL AXIS SELECT |
| 48 |
BASIC 3 AXIS NOT FOUND |
| 49 |
ILLEGAL OPERATION (G68/G69) (M series) |
| 50 |
CHF/CNR NOT ALLOWED IN THRD BLK (M series) |
| 50 |
CHF/CNR NOT ALLOWED IN THRD BLK(T series) |
| 51 |
MISSING MOVE AFTER CHF/CNR (M series) |
| 51 |
MISSING MOVE AFTER CHF/CNR (T series) |
| 52 |
CODE IS NOT G01 AFTER CHF/CNR (M series) |
| 52 |
CODE IS NOT G01 AFTER CHF/CNR (T series) |
| 53 |
TOO MANY ADDRESS COMMANDS (M series) |
| 53 |
TOO MANY ADDRESS COMMANDS (T seires) |
| 54 |
NO TAPER ALLOWED AFTER CHF/CNR (T series) |
| 55 |
MISSING MOVE VALUE IN CHF/CNR (M series) |
| 55 |
MISSING MOVE VALUE IN CHF/CNR (T series) |
| 56 |
NO END POINT & ANGLE IN CHF/CNR (T series) |
| 57 |
NO SOLUTION OF BLOCK END (T series) |
| 58 |
END POINT NOT FOUND (M series) |
| 58 |
END POINT NOT FOUND (T series) |
| 59 |
PROGRAM NUMBER NOT FOUND |
| 60 |
SEQUENCE NUMBER NOT FOUND |
| 61 |
ADDRESS P/Q NOT FOUND IN G70–G73 (T series) |
| 62 |
ILLEGAL COMMAND IN G71–G76 (T series) |
| 63 |
SEQUENCE NUMBER NOT FOUND (T series) |
| 64 |
SHAPE PROGRAM NOT MONOTONOUSLY (T series) |
| 65 |
ILLEGAL COMMAND IN G71–G73 (T series) |
| 66 |
IMPROPER G–CODE IN G71–G73 (T series) |
| 67 |
CAN NOT ERROR IN MDI MODE (T series) |
| 69 |
FORMAT ERROR IN G70–G73 (T series) |
| 70 |
NO PROGRAM SPACE IN MEMORY |
| 71 |
DATA NOT FOUND |
| 72 |
TOO MANY PROGRAMS |
| 73 |
PROGRAM NUMBER ALREADY IN |
| 74 |
ILLEGAL PROGRAM NUMBER |
| 75 |
PROTECT |
| 76 |
ADDRESS P NOT DEFINED |
| 77 |
SUB PROGRAM NESTING ERROR |
| 78 |
NUMBER NOT FOUND |
| 79 |
PROGRAM VERIFY ERROR |
| 80 |
G37 ARRIVAL SIGNAL NOT ASSERTED (M series) |
| 80 |
G37 ARRIVAL SIGNAL NOT ASSERTED (T series) |
| 81 |
OFFSET NUMBER NOT FOUND IN G37 (M series) |
| 81 |
OFFSET NUMBER NOT FOUND IN G37 (T series) |
| 82 |
H–CODE NOT ALLOWED IN G37 (M series) |
| 82 |
T–CODE NOT ALLOWED IN G37 (T series) |
| 83 |
ILLEGAL AXIS COMMAND IN G37 (M series) |
| 83 |
ILLEGAL AXIS COMMAND IN G37 (T series) |
| 85 |
COMMUNICATION ERROR |
| 86 |
DR SIGNAL OFF |
| 87 |
BUFFER OVERFLOW |
| 88 |
LAN FILE TRANS ERROR (CHANNEL–1) |
| 89 |
LAN FILE TRANS ERROR (CHANNEL–2) |
| 90 |
REFERENCE RETURN INCOMPLETE |
| 91 |
REFERENCE RETURN INCOMPLETE |
| 92 |
AXES NOT ON THE REFERENCE POINT |
| 94 |
P TYPE NOT ALLOWED (COORD CHG) |
| 95 |
P TYPE NOT ALLOWED (EXT OFS CHG) |
| 96 |
P TYPE NOT ALLOWED (WRK OFS CHG) |
| 97 |
P TYPE NOT ALLOWED (AUTO EXEC) |
| 98 |
G28 FOUND IN SEQUENCE RETURN |
| 99 |
MDI EXEC NOT ALLOWED AFT. SEARCH |
| 100 |
PARAMETER WRITE ENABLE |
| 101 |
PLEASE CLEAR MEMORY |
| 109 |
FORMAT ERROR IN G08 (M series) |
| 110 |
DATA OVERFLOW |
| 111 |
CALCULATED DATA OVERFLOW |
| 112 |
DIVIDED BY ZERO |
| 113 |
IMPROPER COMMAND |
| 114 |
FORMAT ERROR IN MACRO |
| 115 |
ILLEGAL VARIABLE NUMBER |
| 116 |
WRITE PROTECTED VARIABLE |
| 118 |
PARENTHESIS NESTING ERROR |
| 119 |
ILLEGAL ARGUMENT |
| 122 |
FOUR FOLD MACRO MODAL–CALL |
| 123 |
CAN NOT USE MACRO COMMAND IN DNC |
| 124 |
MISSING END STATEMENT |
| 125 |
FORMAT ERROR IN MACRO |
| 126 |
ILLEGAL LOOP NUMBER |
| 127 |
NC, MACRO STATEMENT IN SAME BLOCK |
| 128 |
ILLEGAL MACRO SEQUENCE NUMBER |
| 129 |
ILLEGAL ARGUMENT ADDRESS |
| 130 |
ILLEGAL AXIS OPERATION |
| 131 |
TOO MANY EXTERNAL ALARM MESSAGES |
| 132 |
ALARM NUMBER NOT FOUND |
| 133 |
ILLEGAL DATA IN EXT. ALARM MSG |
| 135 |
ILLEGAL ANGLE COMMAND (M series) |
| 135 |
SPINDLE ORIENTATION PLEASE (T series) |
| 136 |
C/H–CODE & MOVE CMD IN SAME BLK. (T series) |
| 136 |
ILLEGAL AXIS COMMAND (M series) |
| 137 |
M–CODE & MOVE CMD IN SAME BLK. |
| 138 |
SUPERIMPOSED DATA OVERFLOW |
| 139 |
CAN NOT CHANGE PMC CONTROL AXIS |
| 141 |
CAN NOT COMMAND G51 IN CRC (M series) |
| 142 |
ILLEGAL SCALE RATE (M series) |
| 143 |
SCALED MOTION DATA OVERFLOW (M series) |
| 144 |
ILLEGAL PLANE SELECTED (M series) |
| 145 |
ILLEGAL CONDITIONS IN POLAR COORDINATE INTERPOLATION |
| 146 |
IMPROPER G CODE |
| 148 |
ILLEGAL SETTING DATA (M series) |
| 149 |
FORMAT ERROR IN G10L3 (M series) |
| 150 |
ILLEGAL TOOL GROUP NUMBER |
| 151 |
TOOL GROUP NUMBER NOT FOUND |
| 152 |
NO SPACE FOR TOOL ENTRY |
| 153 |
T–CODE NOT FOUND |
| 154 |
NOT USING TOOL IN LIFE GROUP (M series) |
| 155 |
ILLEGAL T–CODE IN M06 (M series) |
| 155 |
ILLEGAL T–CODE IN M06 (T series) |
| 156 |
P/L COMMAND NOT FOUND |
| 157 |
TOO MANY TOOL GROUPS |
| 158 |
ILLEGAL TOOL LIFE DATA |
| 159 |
TOOL DATA SETTING INCOMPLETE |
| 163 |
COMMAND G68/G69 INDEPENDENTLY T series (At two–path) |
| 175 |
ILLEGAL G107 COMMAND |
| 176 |
IMPROPER G–CODE IN G107 (M series) |
| 176 |
IMPROPER G–CODE IN G107 (T series) |
| 177 |
CHECK SUM ERROR (G05 MODE) |
| 178 |
G05 COMMANDED IN G41/G42 MODE |
| 179 |
PARAM. (NO. 7510) SETTING ERROR |
| 180 |
COMMUNICATION ERROR (REMOTE BUF) |
| 181 |
FORMAT ERROR IN G81 BLOCK (Hobbing machine, EGB) (M series) |
| 182 |
G81 NOT COMMANDED (Hobbing machine) (M series) |
| 183 |
DUPLICATE G83 (COMMANDS) (Hobbing machine) (M series) |
| 184 |
ILLEGAL COMMAND IN G81 (Hobbing machine, EGB) (M series) |
| 185 |
RETURN TO REFERENCE POINT (Hobbing machine) (M series) |
| 186 |
PARAMETER SETTING ERROR (Hobbing machine, EGB) (M series) |
| 187 |
HOB COMMAND IS NOT ALLOWED |
| 190 |
ILLEGAL AXIS SELECT (M series) |
| 194 |
SPINDLE COMMAND IN SYNCHRO–MODE |
| 195 |
MODE CHANGE ERROR |
| 197 |
C–AXIS COMMANDED IN SPINDLE MODE |
| 199 |
MACRO WORD UNDEFINED |
| 200 |
ILLEGAL S CODE COMMAND |
| 201 |
FEEDRATE NOT FOUND IN RIGID TAP |
| 202 |
POSITION LSI OVERFLOW |
| 203 |
PROGRAM MISS AT RIGID TAPPING |
| 204 |
ILLEGAL AXIS OPERATION |
| 205 |
RIGID MODE DI SIGNAL OFF |
| 206 |
CAN NOT CHANGE PLANE (RIGID TAP) (M series) |
| 207 |
RIGID DATA MISMATCH |
| 210 |
CAN NOT COMAND M198/M199 |
| 211 |
G31 (HIGH) NOT ALLOWED IN G99 |
| 212 |
ILLEGAL PLANE SELECT (M series) |
| 212 |
ILLEGAL PLANE SELECT (T series) |
| 213 |
ILLEGAL COMMAND IN SYNCHRO–MODE |
| 213 |
ILLEGAL COMMAND IN SYNCHRO–MODE (T series) |
| 214 |
ILLEGAL COMMAND IN SYNCHRO–MODE |
| 217 |
DUPLICATE G51.2 (COMMANDS) (T series) |
| 218 |
NOT FOUND P/Q COMMAND IN G251 (T series) |
| 219 |
COMMAND G250/G251 INDEPENDENTLY (T series) |
| 220 |
ILLEGAL COMMAND IN SYNCHR–MODE (T series) |
| 221 |
ILLEGAL COMMAND IN SYNCHR–MODE (T series) |
| 222 |
DNC OP. NOT ALLOWED IN BG.–EDIT (M series) |
| 224 |
RETURN TO REFERENCE POINT (M series) |
| 224 |
RETURN TO REFERENCE POINT (T series) |
| 225 |
SYNCHRONOUS/MIXED CONTROL ERROR (T series (At two–path)) |
| 226 |
ILLEGAL COMMAND IN SYNCHRO– MODE (T series (At two–path)) |
| 229 |
CAN NOT KEEP SYNCHRO–STATE (T series) |
| 230 |
R CODE NOT FOUND (Grinding machine) (M series) |
| 231 |
ILLEGAL FORMAT IN G10 OR L50 |
| 233 |
DEVICE BUSY |
| 239 |
BP/S ALARM |
| 240 |
BP/S ALARM |
| 244 |
P/S ALARM (T series) |
| 245 |
T–CODE NOT ALOWEE IN THIS BLOCK (T series) |
| 251 |
ATC ERROR (M series) |
| 252 |
ATC SPINDLE ALARM (M series) |
| 253 |
G05 IS NOT AVAILABLE (M series) |
| 300 |
n AXIS NEED ZRN |
| 301 |
APC ALARM:n AXIS COMMUNICATION |
| 302 |
APC ALARM:n AXIS OVER TIME |
| 303 |
APC ALARM:n AXIS FRAMING |
| 304 |
APC ALARM:n AXIS PARITY |
| 305 |
APC ALARM:n AXIS PULSE MISS |
| 306 |
APC ALARM:n AXIS BATTERY ZERO |
| 307 |
APC ALARM:n AXIS BATTERY DOWN 1 |
| 308 |
APC ALARM:n AXIS BATTERY DOWN 2 |
| 309 |
APC ALARM:n AXIS ZRN IMPOSSIBLE |
| 360 |
n AXIS : ABNORMAL CHECKSUM (INT) |
| 361 |
n AXIS : ABNORMAL PHASE DATA (INT) |
| 362 |
n AXIS : ABNORMAL REV.DATA (INT) |
| 363 |
n AXIS : ABNORMAL CLOCK (INT) |
| 364 |
n AXIS : SOFT PHASE ALARM (INT) |
| 365 |
n AXIS : BROKEN LED (INT) |
| 366 |
n AXIS : PULSE MISS (INT) |
| 367 |
n AXIS : COUNT MISS (INT) |
| 368 |
n AXIS : SERIAL DATA ERROR (INT) |
| 369 |
n AXIS : DATA TRANS. ERROR (INT) |
| 380 |
n AXIS : BROKEN LED (EXT) |
| 381 |
n AXIS : ABNORMAL PHASE (EXT LIN) |
| 382 |
n AXIS : COUNT MISS (EXT) |
| 383 |
n AXIS : PULSE MISS (EXT) |
| 384 |
n AXIS : SOFT PHASE ALARM (EXT) |
| 385 |
n AXIS : SERIAL DATA ERROR (EXT) |
| 386 |
n AXIS : DATA TRANS. ERROR (EXT) |
| 387 |
n AXIS : ABNORMAL ENCODER (EXT) |
| 400 |
SERVO ALARM: n–TH AXIS OVERLOAD |
| 401 |
SERVO ALARM: n–TH AXIS VRDY OFF |
| 402 |
SERVO ALARM: SV CARD NOT EXIST |
| 403 |
SERVO ALARM: CARD/SOFT MISMATCH |
| 404 |
SERVO ALARM: n–TH AXIS VRDY ON |
| 405 |
SERVO ALARM: (ZERO POINT RETURN FAULT) |
| 407 |
SERVO ALARM: EXCESS ERROR |
| 409 |
SERVO ALARM: n AXIS TORQUE ALM |
| 410 |
SERVO ALARM: n–TH AXIS – EXCESS ERROR |
| 411 |
SERVO ALARM: n–TH AXIS – EXCESS ERROR |
| 413 |
SERVO ALARM: n–th AXIS – LSI OVERFLOW |
| 414 |
SERVO ALARM: n–TH AXIS – DETECTION RELATED ERROR |
| 415 |
SERVO ALARM: n–TH AXIS – EXCESS SHIFT |
| 416 |
SERVO ALARM: n–TH AXIS – DISCONNECTION |
| 417 |
SERVO ALARM: n–TH AXIS – PARAMETER INCORRECT |
| 420 |
SERVO ALARM: n AXIS SYNC TORQUE (M series) |
| 421 |
SERVO ALARM: n AXIS EXCESS ER (D) |
| 422 |
SERVO ALARM: n AXIS |
| 423 |
SERVO ALARM: n AXIS |
| 430 |
n AXIS : SV. MOTOR OVERHEAT |
| 431 |
n AXIS : CNV. OVERLOAD |
| 432 |
n AXIS : CNV. LOW VOLT CONTROL |
| 433 |
n AXIS : CNV. LOW VOLT DC LINK |
| 434 |
n AXIS : INV. LOW VOLT CONTROL |
| 435 |
n AXIS : INV. LOW VOLT DC LINK |
| 436 |
n AXIS : SOFTTHERMAL (OVC) |
| 437 |
n AXIS : CNV. OVERCURRENT POWER |
| 438 |
n AXIS : INV. ABNORMAL CURRENT |
| 439 |
n AXIS : CNV. OVER VOLT DC LINK |
| 440 |
n AXIS : CNV. EX DECELERATION POW. |
| 441 |
n AXIS : ABNORMAL CURRENT OFFSET |
| 442 |
n AXIS : CNV. CHARGE FAILURE |
| 443 |
n AXIS : CNV. COOLING FAN FAILURE |
| 444 |
n AXIS : INV. COOLING FAN FAILURE |
| 445 |
n AXIS : SOFT DISCONNECT ALARM |
| 446 |
n AXIS : HARD DISCONNECT ALARM |
| 447 |
n AXIS : HARD DISCONNECT (EXT) |
| 448 |
n AXIS : UNMATCHED FEEDBACK ALARM |
| 449 |
n AXIS : INV. IPM ALARM |
| 453 |
n AXIS : SPC SOFT DISCONNECT ALARM |
| 456 |
n AXIS : ILLEGAL CURRENT LOOP |
| 457 |
n AXIS : ILLEGAL HI HRV (250US) |
| 458 |
n AXIS : CURRENT LOOP ERROR |
| 459 |
n AXIS : HI HRV SETTING ERROR |
| 460 |
n AXIS : FSSB DISCONNECT |
| 461 |
n AXIS : ILLEGAL AMP INTERFACE |
| 462 |
n AXIS : SEND CNC DATA FAILED |
| 463 |
n AXIS : SEND SLAVE DATA FAILED |
| 464 |
n AXIS : WRITE ID DATA FAILED |
| 465 |
n AXIS : READ ID DATA FAILED |
| 466 |
n AXIS : MOTOR/AMP COMBINATION |
| 467 |
n AXIS : ILLEGAL SETTING OF AXIS |
| 468 |
n AXIS : HI HRV SETTING ERROR (AMP) |
| 500 |
OVER TRAVEL : +n |
| 501 |
OVER TRAVEL : –n |
| 502 |
OVER TRAVEL : +n |
| 503 |
OVER TRAVEL : –n |
| 504 |
OVER TRAVEL : +n |
| 505 |
OVER TRAVEL : –n |
| 506 |
OVER TRAVEL : +n |
| 507 |
OVER TRAVEL : –n |
| 700 |
OVERHEAT: CONTROL UNIT |
| 701 |
OVERHEAT: FAN MOTOR |
| 704 |
OVERHEAT: SPINDLE |
| 740 |
RIGID TAP ALARM : EXCESS ERROR |
| 741 |
RIGID TAP ALARM : EXCESS ERROR |
| 742 |
RIGID TAP ALARM : LSI OVER FLOW |
| 749 |
S–SPINDLE LSI ERROR |
| 750 |
SPINDLE SERIAL LINK START FAULT |
| 751 |
FIRST SPINDLE ALARM DETECTION (AL–XX) |
| 752 |
FIRST SPINDLE MODE CHANGE FAULT |
| 754 |
SPINDLE–1 ABNORMAL TORQUE ALM |
| 761 |
SECOND SPINDLE ALARM DETECTION (AL–XX) |
| 762 |
SECOND SPINDLE MODE CHANGE FAULT |
| 764 |
SPINDLE–2 ABNORMAL TORQUE ALM |
| 771 |
SPINDLE–3 ALARM DETECT (AL–XX) |
| 772 |
SPINDLE–3 MODE CHANGE ERROR |
| 774 |
SPINDLE–3 ABNORMAL TORQUE ALM |
| 782 |
SPINDLE–4 MODE CHANGE ERROR |
| 784 |
SPINDLE–4 ABNORMAL TORQUE ALM |
| 900 |
ROM PARITY |
| 910 |
SRAM PARITY : (BYTE 0) |
| 911 |
SRAM PARITY : (BYTE 1) |
| 912 |
DRAM PARITY : (BYTE 0) |
| 913 |
DRAM PARITY : (BYTE 1) |
| 914 |
DRAM PARITY : (BYTE 2) |
| 915 |
DRAM PARITY : (BYTE 3) |
| 916 |
DRAM PARITY : (BYTE 4) |
| 917 |
DRAM PARITY : (BYTE 5) |
| 918 |
DRAM PARITY : (BYTE 6) |
| 919 |
DRAM PARITY : (BYTE 7) |
| 920 |
SERVO ALARM (1–4 AXIS) |
| 921 |
SERVO ALARM (5–8 AXIS) |
| 926 |
FSSB ALARM |
| 930 |
CPU INTERRUPUT |
| 935 |
SRAM ECC ERROR |
| 950 |
PMC SYSTEM ALARM |
| 951 |
PMC WATCH DOG ALARM |
| 970 |
NMI OCCURRED IN PMCLSI |
| 971 |
NMI OCCURRED IN SLC |
| 972 |
NMI OCCURRED IN OTHER MODULE |
| 973 |
NON MASK INTERRUPT |
| 974 |
F–BUS ERROR |
| 975 |
BUS ERROR |
| 976 |
L–BUS ERROR |
| 4500 |
REPOSITIONING INHIBITED |
| 4502 |
ILLEGAL COMMAND IN BOLT HOLE |
| 4503 |
ILLEGAL COMMAND IN LINE AT ANGLE |
| 4504 |
ILLEGAL COMMAND IN ARC |
| 4505 |
ILLEGAL COMMAND IN GRID |
| 4506 |
ILLEGAL COMMAND IN SHARE PROOFS |
| 4507 |
ILLEGAL COMMAND IN SQUARE |
| 4508 |
ILLEGAL COMMAND IN RADIUS |
| 4509 |
ILLEGAL COMMAND IN CUT AT ANGLE |
| 4510 |
ILLEGAL COMMAND IN LINE-PUNCH |
| 4511 |
ILLEGAL COMMAND IN CIRCLE-PUNCH |
| 4520 |
T, M INHIBITED IN NIBBLING-MODE |
| 4521 |
EXCESS NIBBLING MOVEMENT (X, Y) |
| 4522 |
EXCESS NIBBLING MOVEMENT (C) |
| 4523 |
ILLEGAL COMMAND IN CIRCLE-NIBBL |
| 4524 |
ILLEGAL COMMAND IN LINE-NIBBL |
| 4530 |
A/B MACRO NUMBER ERROR |
| 4531 |
U/V MACRO FORMAT ERROR |
| 4532 |
IMPROPER U/V MACRO NUMBER |
| 4533 |
U/V MACRO MEMORY OVERFLOW |
| 4534 |
W MACRO NUMBER NOT FOUND |
| 4535 |
U/V MACRO NESTING ERROR |
| 4536 |
NO W, Q COMMAND IN MULTI-PIECE |
| 4537 |
ILLEGAL Q VALUE IN MULTI-PIECE |
| 4538 |
W NO. NOT FOUND IN MULTI-PIECE |
| 4539 |
MULTI-PIECE SETTING IS ZERO |
| 4540 |
MULTI-PIECE COMMAND WITHIN MACRO |
| 4542 |
MULTI-PIECE COMMAND ERROR |
| 4543 |
MULTI-PIECE Q COMMAND ERROR |
| 4544 |
MULTI-PIECE RESTART ERROR |
| 4549 |
ILLEGAL TOOL DATA FORMAT |
| 4600 |
T, C COMMAND IN INTERPOLATION |
| 4601 |
INHIBITED T, M COMMAND |
| 4602 |
ILLEGAL T-CODE |
| 4603 |
C AXIS SYNCHRONOUS ERROR |
| 4604 |
ILLEGAL AXIS OPERATION |
| 4605 |
NEED ZRN |
| 4630 |
ILLEGAL COMMAND IN LASER MODE |
| 4650 |
IMPROPER G-CODE IN OFFSET MODE |
| 4700 |
PROGRAM ERROR (OT +) |
| 4701 |
PROGRAM ERROR (OT –) |
| 4702 |
PROGRAM ERROR (OT +) |
| 4703 |
PROGRAM ERROR (OT –) |
| 4704 |
PROGRAM ERROR (OT +) |
| 4705 |
PROGRAM ERROR (OT –) |
| 4815 |
ZONE : ENTERING INHIBITED 3 –X |
| 5000 |
ILLEGAL COMMAND CODE (M series) |
| 5003 |
ILLEGAL PARAMETER (HPCC) (M series) |
| 5004 |
HPCC NOT READY |
| 5006 |
TOO MANY WORD IN ONE BLOCK (M series) |
| 5007 |
TOO LARGE DISTANCE (M series) |
| 5009 |
PARAMETER ZERO (DRY RUN) (M series) |
| 5010 |
END OF RECORD |
| 5012 |
G05 P10000 ILLEGAL START UP (HPCC) (M series) |
| 5013 |
HPCC: CRC OFS REMAIN AT CANCEL (M series) |
| 5014 |
TRACE DATA NOT FOUND (M series) |
| 5018 |
POLYGON SPINDLE SPEED ERROR (T series) |
| 5020 |
PARAMETER OF RESTART ERROR |
| 5030 |
ILLEGAL COMMAND (G100) (T series) |
| 5031 |
ILLEGAL COMMAND (G100, G102, G103) (T series) |
| 5032 |
NEW PRG REGISTERED IN B–AXS MOVE (T series) |
| 5033 |
NO PROG SPACE IN MEMORY B–AXS (T series) |
| 5034 |
PLURAL COMMAND IN G110 (T series) |
| 5035 |
NO FEEDRATE COMMANDED B–AXS (T series) |
| 5036 |
ADDRESS R NOT DEFINED IN G81–G86 (T series) |
| 5037 |
ADDRESS Q NOT DEFINED IN G83 (T series) |
| 5038 |
TOO MANY START M–CODE COMMAND (T series) |
| 5039 |
START UNREGISTERED B–AXS PROG (T series) |
| 5040 |
CAN NOT COMMANDED B–AXS MOVE (T series) |
| 5041 |
CAN NOT COMMANDED G110 BLOCK (T series) |
| 5044 |
G68 FORMAT ERROR (M series) |
| 5046 |
ILLEGAL PARAMETER (ST.COMP) |
| 5050 |
ILL–COMMAND IN CHOPPING MODE (M series) |
| 5051 |
M–NET CODE ERROR |
| 5052 |
M–NET ETX ERROR |
| 5053 |
M–NET CONNECT ERROR |
| 5054 |
M–NET RECEIVE ERROR |
| 5055 |
M–NET PRT/FRT ERROR |
| 5057 |
M–NET BOARD SYSTEM DOWN |
| 5058 |
G35/G36 FORMAT ERROR (T series) |
| 5059 |
RADIUS IS OUT OF RANGE |
| 5059 |
RADIUS IS OUT OF RANGE (T series) |
| 5060 |
ILLEGAL PARAMETER IN G02.3/G03.3 (M series) |
| 5061 |
ILLEGAL FORMAT IN G02.3/G03.3 (M series) |
| 5062 |
ILLEGAL COMMAND IN G02.3/G03.3 |
| 5063 |
IS NOT PRESET AFTER REF. (M series) |
| 5064 |
DIFFERRENT AXIS UNIT (IS–B, IS–C) |
| 5065 |
DIFFERENT AXIS UNIT (PMC AXIS) (M series) |
| 5067 |
(HPCC) (M series) |
| 5068 |
G31 FORMAT ERROR (M series) |
| 5069 |
WHL–C:ILLEGA P–DATA (M series) |
| 5073 |
NO DECIMAL POINT |
| 5074 |
ADDRESS DUPLICATION ERROR |
| 5082 |
DATA SERVER ERROR |
| 5085 |
SMOOTH IPL ERROR 1 |
| 5096 |
MISMATCH WAITING M–CODE |
| 5110 |
IMPROPER G–CODE (G05.1 G1 MODE) (M series) |
| 5111 |
IMPROPER MODAL G–CODE (G05.1 G1) (M series) |
| 5112 |
G08 CAN NOT BE COMMANDED (G05.1 G1) (M series) |
| 5113 |
CAN NOT ERROR IN MDI MODE (G05.1) (M series) |
| 5114 |
NOT STOP POSITION (G05.1 Q1) (M series) |
| 5115 |
SPL : ERROR (M series) |
| 5116 |
SPL : ERROR (M series) |
| 5117 |
SPL : ERROR (M series) |
| 5118 |
SPL : ERROR (M series) |
| 5122 |
ILLEGAL COMMAND IN SPIRAL (M series) |
| 5123 |
OVER TOLERANCE OF END POINT (M series) |
| 5124 |
CAN NOT COMMAND SPIRAL (M series) |
| 5134 |
FSSB : OPEN READY TIME OUT |
| 5135 |
FSSB : ERROR MODE |
| 5136 |
FSSB : NUMBER OF AMPS IS SMALL |
| 5137 |
FSSB : CONFIGURATION ERROR |
| 5138 |
FSSB : AXIS SETTING NOT COMPLETE |
| 5139 |
FSSB : ERROR |
| 5155 |
NOT RESTART PROGRAM BY G05 |
| 5156 |
ILLEGAL AXIS OPERATION (M series) |
| 5157 |
PARAMETER ZERO (M series) |
| 5195 |
DIRECTION CAN NOT BE JUDGED (T series) |
| 5196 |
ILLEGAL OPERATION (HPCC) (M series) |
| 5197 |
FSSB : OPEN TIME OUT |
| 5198 |
FSSB : ID DATA NOT READ |
| 5199 |
FINE TORQUE SENSING PARAMETER |
| 5212 |
SCREEN COPY : PARAMETER ERROR |
| 5213 |
SCREEN COPY : COMMUNICATION ERROR |
| 5214 |
SCREEN COPY : DATA TRANSFER ERROR |
| 5218 |
ILLEGAL PARAMETER (INCL. COMP) |
| 5219 |
CAN NOT RETURN |
| 5220 |
REFERENCE POINT ADJUSTMENT MODE |
| 5222 |
SRAM CORRECTABLE ERROR |
| 5227 |
FILE NOT FOUND |
| 5228 |
SAME NAME USED |
| 5229 |
WRITE PROTECTED |
| 5231 |
TOO MANY FILES |
| 5232 |
DATA OVER–FLOW |
| 5235 |
COMMUNICATION ERROR |
| 5237 |
READ ERROR |
| 5238 |
WRITE ERROR |
| 5242 |
ILLEGAL AXIS NUMBER (M series) |
| 5243 |
DATA OUT OF RANGE (M series) |
| 5244 |
TOO MANY DI ON (M series) |
| 5245 |
OTHER AXIS ARE COMMANDED (M series) |
| 5251 |
ILLEGAL PARAMETER IN G54.2 (M series) |
| 5252 |
ILLEGAL P COMMAND IN G54.2 (M series) |
| 5257 |
G41/G42 NOT ALLOWED IN MDI MODE (M series) |
| 5257 |
G41/G42 NOT ALLOWED IN MDI MODE (T series) |
| 5300 |
SET ALL OFFSET DATAS AGAIN |
| 5302 |
ILLEGAL COMMAND IN G68 MODE |
| 5303 |
TOUCH PANEL ERROR |
| 5306 |
MODE CHANGE ERROR |
| 5307 |
INTERNAL DATA OVER FLOW (M series) |
| 5311 |
FSSB:ILLEGAL CONNECTION |
| 5321 |
S–COMP. VALUE OVERFLOW |
| 5400 |
SPL:ILLEGAL AXIS COMMAND (M series) |
| 5401 |
SPL:ILLEGAL COMMAND (M series) |
| 5402 |
SPL:ILLEGAL AXIS MOVING (M series) |
| 5403 |
SPL:CAN NOT MAKE VECTOR (M series) |
| 5405 |
ILLEGAL PARAMETER IN G41.2/ G42.2 (M series) |
| 5406 |
G41.3/G40 FORMAT ERROR (M series) |
| 5407 |
ILLEGAL COMMAND IN G41.3 (M series) |
| 5408 |
G41.3 ILLEGAL START_UP (M series) |
| 5409 |
ILLEGAL PARAMETER IN G41.3 (M series) |
| 5411 |
NURBS:ILLEGAL ORDER (M series) |
| 5412 |
NURBS:NO KNOT COMMAND (M series) |
| 5413 |
NURBS:ILLEGAL AXIS COMMAND (M series) |
| 5414 |
NURBS:ILLEGAL KNOT (M series) |
| 5415 |
NURBS:ILLEGAL CANCEL (M series) |
| 5416 |
NURBS:ILLEGAL MODE (M series) |
| 5417 |
NURBS:ILLEGAL MULTI–KNOT (M series) |
| 5418 |
NURBS:ILLEGAL KNOT VALUE (M series) |
| 5420 |
ILLEGAL PARAMETER IN G43.4/ G43.5 (M series) |
| 5421 |
ILLEGAL COMMAND IN G43.4/ G43.5 (M series) |
| 5422 |
EXCESS VELOCITY IN G43.4/ G43.5 (M series) |
| 5425 |
ILLEGAL OFFSET VALUE (M series) |
| 5430 |
ILLEGAL COMMAND IN 3–D CIR (M series) |
| 5432 |
G02.4/G03.4 FORMAT ERROR (M series) |
| 5433 |
MANUAL INTERVENTION IN 3–D CIR (M series) |
| 5435 |
PARAMETER OUT OF RANGE (TLAC) (M series) |
| 5436 |
PARAMETER SETTING ERROR 1 (TLAC) (M series) |
| 5437 |
PARAMETER SETTING ERROR 2 (TLAC) (M series) |
| 5440 |
ILLEGAL DRILLING AXIS SELECTED (M series) |
| 5445 |
CRC:MOTION IN G39 (M series) |
| 5446 |
CRC:NO AVOIDANCE (M series) |
| 5447 |
CRC:DANGEROUS AVOIDANCE (M series) |
| 5448 |
CRC:INTERFERENCE TO AVD. (M series) |
| 5452 |
IMPROPER G–CODE (5AXIS MODE) (M series) |
| 5453 |
NOTE: G68 IS CANCELED (HPCC) (M series) |
| 5455 |
ILLEGAL ACC. PARAMETER (M series) |
| 4800 |
ZONE: PUNCHING INHIBITED 1 |
| 4801 |
ZONE: PUNCHING INHIBITED 2 |
| 4802 |
ZONE: PUNCHING INHIBITED 3 |
| 4803 |
ZONE: PUNCHING INHIBITED 4 |
| 4804 |
ZONE: ENTERING INHIBITED 1 +X |
| 4805 |
ZONE: ENTERING INHIBITED 1 –X |
| 4806 |
ZONE: ENTERING INHIBITED 2 +X |
| 4807 |
ZONE: ENTERING INHIBITED 2 –X |
| 4808 |
ZONE: ENTERING INHIBITED 3 +X |
| 4809 |
ZONE: ENTERING INHIBITED 4 +X |
| 4810 |
ZONE: ENTERING INHIBITED 4 –X |
| 4811 |
ZONE: ENTERING INHIBITED 1 +Y |
| 4812 |
ZONE: ENTERING INHIBITED 1 –Y |
| 4813 |
ZONE: ENTERING INHIBITED 2 +Y |
| 4814 |
ZONE: ENTERING INHIBITED 2 –Y |
| 4815 |
ZONE: ENTERING INHIBITED 3 +Y |
| 4816 |
ZONE: ENTERING INHIBITED 3 –Y |
| 4817 |
ZONE: ENTERING INHIBITED 4 +Y |
| 4818 |
ZONE: ENTERING INHIBITED 4 –Y |
| 4870 |
AUTO SETTING FEED ERROR |
| 4871 |
AUTO SETTING PIECES ERROR |
| 4872 |
AUTO SETTING COMMAND ERROR |
