Henny penny фритюрница ошибка e10

product

DISPLAY

«E04»

Control board overheating

«E05»

Shortening overheating

«E06»

Temperature probe failure

«E41»

Programming Failure

«E71»

Pump motor relay failure or

wiring problem

1103

In the event of a control system failure, the digital display

shows an error message. These messages are coded: «E04»,

«E05», «E06», «E41». A constant tone is heard when an error

code is displayed, and to silence this tone, press any of the

CAUSE

buttons.

PANEL BOARD CORRECTION

Turn switch to OFF position, then turn

switch back to ON; if display still shows

«E04», the board is getting too hot; check

for signs of overheating behind the control

panel; once panel cools down the controls

should return to normal; if «E04» persists,

replace the control

Turn switch to OFF position, then back to

ON; if display shows «E05», the heating

circuits and temperature probe should be

checked; once the unit cools down, the

controls should return to normal; if «E05»

persists, replace the controls

Turn switch to OFF position, then back to

ON; if the display shows «E06», the tem-

perature probe should be checked; once the

temperature probe is repaired, or replaced,

controls should return to normal; if «E06»

persists, replace the controls

Turn switch to OFF position, then back to

ON. If display shows «E41», the control

should be re-initialized (see programming

section); if the error code persists, replace

the control panel.

Replace relay if contacts are stuck closed;

check wiring on POWER/PUMP switch, or

wall receptacle; L1 and N may be reversed

Model 590/592

1-11

Model EEE-141,142, 143, 144

7-2.    ERROR CODES

In the event of a control system failure, the digital display shows an
error message.  The message codes are shown in the DISPLAY
column below.  A constant tone is heard when an error code is
displayed, and to silence this tone, press any button.

DISPLAY

CAUSE

CORRECTION

“E-4”

Control board

Turn switch to OFF position, then turn switch back to ON;

overheating

if display shows “E-4”, the control board is getting too hot;
check the louvers on each side of the unit for obstructions

“E-5”

Oil

Turn switch to OFF position, then turn switch back to ON;

overheating

if display shows “E-5”, the heating circuits and temperature
probes should be checked

“E-6A”

Temperature

Turn switch to OFF position, then turn switch back to ON;

probe open

if display shows “E-6A”, the temperature probe should be
checked

“E-6B”

Temperature

Turn switch to OFF position, then turn switch back to ON;

probe shorted

if display shows “E-6B”, the temperature probe should be
checked

“E-10”

High limit

Reset the high limit by using a small screwdriver or Allen
wrench gently pushing it into the hole in the heating element
hinge; if high limit does not reset, high limit may need be replaced

“E-15”

Drain switch

Make sure drain knob is completely pushed-in; if E-15 persists,
have drain switch checked

“E-18-A”

Left level sensor open

Turn switch to OFF position, then turn switch back to ON;

“E-18-B”

Right level sensor open

if display still indicates a failed sensor, have the connectors checked

“E-18-C”

Both level sensors open at the control board; have sensor checked & replace if necessory

209

       7-3

  1. Доброго дня коллеги. Имеется на обслуге фритюрница Henny Penny Computron 8000. Так вот. Жарка происходит под давлением, после окончания жарки должен происходить сброс давления паров через соленоид (по словам поваров). Этого не происходит. Сброс пара осуществляют методом «Хорошо ударить по корпусу соленоида». Подскажите в какую сторону копать и если можно эл. схему на данный девайс. Копать по проводам не дают, долго, а фритюрница постоянно в работе

  2. Куда ударяют и работает,там и проблема. Попробуйте разобрать.

  3. Ударяют просто сверху по корпусу соленоида и катушка. Нет питания на катушку, почему схему прошу чтоб понять при каком условии и откуда должно податься питание на катушку соленоида

  4. В любом случае надо разобрать, чтобы найти плату управления, раз от удара работает-значит плохой контакт где то

  5. блин да я это все прекрасно понимаю. Я ж написал что долго ковыряться не дадут. А без схемы это все будет тыканием слепого котенка

  6. Ознакомьтесь с инструкцией, может поможет.

    Вложения:

  8. За документацию огромное спасибо. Даа от схемы я большего конечно ждал. Ну с помощью инструкции думаю осилю

Поделиться этой страницей

Ad 1 Руководство по эксплуатации Henny Penny 324 Henny Penny 324 2 Руководство по эксплуатации Henny Penny 302 Henny Penny 302 3 Руководство по эксплуатации Henny Penny 341 Henny Penny 341 4 Руководство по эксплуатации Henny Penny 322 Henny Penny 322 5 Руководство по эксплуатации Henny Penny 323 Henny Penny 323 6 Руководство по эксплуатации Henny Penny 301 Henny Penny 301 7 Руководство по эксплуатации Henny Penny 500 Henny Penny 500 8 Руководство по эксплуатации Henny Penny 291 Henny Penny 291 9 Руководство по эксплуатации Henny Penny 303 Henny Penny 303 10 Руководство по эксплуатации Henny Penny 580 KFC Henny Penny 580 KFC 11 Руководство по эксплуатации Henny Penny 561 Henny Penny 561 12 Руководство по эксплуатации Henny Penny 580 Henny Penny 580 13 Руководство по эксплуатации Henny Penny 581 Henny Penny 581 14 Руководство по эксплуатации Henny Penny 342 Henny Penny 342 15 Руководство по эксплуатации Henny Penny 680 KFC Henny Penny 680 KFC 16 Руководство по эксплуатации Henny Penny 690 Henny Penny 690 17 Руководство по эксплуатации Henny Penny 691 Henny Penny 691 18 Руководство по эксплуатации Henny Penny 600 Henny Penny 600 19 Руководство по эксплуатации Henny Penny CFA 600 Henny Penny CFA 600 20 Руководство по эксплуатации Henny Penny COMPUTRON 7000 500 Henny Penny COMPUTRON 7000 500 21 Руководство по эксплуатации Henny Penny CFA 500 Henny Penny CFA 500 22 Руководство по эксплуатации Henny Penny CLIMAPLUS LCG Henny Penny CLIMAPLUS LCG 23 Руководство по эксплуатации Henny Penny 803 Henny Penny 803 24 Руководство по эксплуатации Henny Penny CLIMAPLUS LCS Henny Penny CLIMAPLUS LCS 25 Руководство по эксплуатации Henny Penny COMPUTRON 8000 Henny Penny COMPUTRON 8000 26 Руководство по эксплуатации Henny Penny COMPUTRON 7000 600 Henny Penny COMPUTRON 7000 600 27 Руководство по эксплуатации Henny Penny COMPUTRON 7000 Henny Penny COMPUTRON 7000 28 Руководство по эксплуатации Henny Penny 592 Henny Penny 592 29 Руководство по эксплуатации Henny Penny EEE-144 Henny Penny EEE-144 30 Руководство по эксплуатации Henny Penny EVOLUTION ELITE EEG-141 Henny Penny EVOLUTION ELITE EEG-141 31 Руководство по эксплуатации Henny Penny EVOLUTION ELITE EEG-143 Henny Penny EVOLUTION ELITE EEG-143 32 Руководство по эксплуатации Henny Penny EVOLUTION ELITE EEG-144 Henny Penny EVOLUTION ELITE EEG-144 33 Руководство по эксплуатации Henny Penny EEE-142 Henny Penny EEE-142 34 Руководство по эксплуатации Henny Penny FM05-032-G Henny Penny FM05-032-G 35 Руководство по эксплуатации Henny Penny FM03-681 Henny Penny FM03-681 36 Руководство по эксплуатации Henny Penny EVOLUTION ELITE EEG-142 Henny Penny EVOLUTION ELITE EEG-142 37 Руководство по эксплуатации Henny Penny FDS-100 Henny Penny FDS-100 38 Руководство по эксплуатации Henny Penny FDS-200 Henny Penny FDS-200 39 Руководство по эксплуатации Henny Penny EEE-143 Henny Penny EEE-143 40 Руководство по эксплуатации Henny Penny FM07-020-F Henny Penny FM07-020-F 41 Руководство по эксплуатации Henny Penny FS-100 Henny Penny FS-100 42 Руководство по эксплуатации Henny Penny EIGHT HEAD COOKERS 680 Henny Penny EIGHT HEAD COOKERS 680 43 Руководство по эксплуатации Henny Penny G L O S S A R Y OFE- 290 Henny Penny G L O S S A R Y OFE- 290 44 Руководство по эксплуатации Henny Penny ODG-323 gas Henny Penny ODG-323 gas 45 Руководство по эксплуатации Henny Penny OE 301 Henny Penny OE 301 46 Руководство по эксплуатации Henny Penny OE-301/302/303 Henny Penny OE-301/302/303 47 Руководство по эксплуатации Henny Penny none Henny Penny none 48 Руководство по эксплуатации Henny Penny OE-100 Henny Penny OE-100 49 Руководство по эксплуатации Henny Penny OE-30X Henny Penny OE-30X 50 Руководство по эксплуатации Henny Penny OE/OG 303 Henny Penny OE/OG 303 51 Руководство по эксплуатации Henny Penny ODE-323 electri Henny Penny ODE-323 electri 52 Руководство по эксплуатации Henny Penny ODE/ODG-323 Henny Penny ODE/ODG-323 53 Руководство по эксплуатации Henny Penny FS-200 Henny Penny FS-200 54 Руководство по эксплуатации Henny Penny OE/OG 301 Henny Penny OE/OG 301 55 Руководство по эксплуатации Henny Penny OE/OG 301/302/303 Henny Penny OE/OG 301/302/303 56 Руководство по эксплуатации Henny Penny OE/OG 302 Henny Penny OE/OG 302 57 Руководство по эксплуатации Henny Penny OEA Henny Penny OEA 58 Руководство по эксплуатации Henny Penny OEA-342 Henny Penny OEA-342 59 Руководство по эксплуатации Henny Penny OEA-322 Henny Penny OEA-322 60 Руководство по эксплуатации Henny Penny OEA/OGA-322 Henny Penny OEA/OGA-322 61 Руководство по эксплуатации Henny Penny OEA/OGA-324 Henny Penny OEA/OGA-324 62 Руководство по эксплуатации Henny Penny OEA/OGA-323 Henny Penny OEA/OGA-323 63 Руководство по эксплуатации Henny Penny OEA-323 Henny Penny OEA-323 64 Руководство по эксплуатации Henny Penny OEA/OGA-321 Henny Penny OEA/OGA-321 65 Руководство по эксплуатации Henny Penny OFE-322 Henny Penny OFE-322 66 Руководство по эксплуатации Henny Penny OEA/OGA-342 Henny Penny OEA/OGA-342 67 Руководство по эксплуатации Henny Penny OFE- 291 Henny Penny OFE- 291 68 Руководство по эксплуатации Henny Penny OEA/OGA-341 Henny Penny OEA/OGA-341 69 Руководство по эксплуатации Henny Penny OFE-321 Henny Penny OFE-321 70 Руководство по эксплуатации Henny Penny OFE-323 Henny Penny OFE-323 71 Руководство по эксплуатации Henny Penny OFE Henny Penny OFE 72 Руководство по эксплуатации Henny Penny OFE/OFG-321 Henny Penny OFE/OFG-321 73 Руководство по эксплуатации Henny Penny OFE-342 Henny Penny OFE-342 74 Руководство по эксплуатации Henny Penny OFE/OFG-341 Henny Penny OFE/OFG-341 75 Руководство по эксплуатации Henny Penny OFE-341 Henny Penny OFE-341 76 Руководство по эксплуатации Henny Penny OFE/OFG-342 Henny Penny OFE/OFG-342 77 Руководство по эксплуатации Henny Penny OFE/OFG-322 Henny Penny OFE/OFG-322 78 Руководство по эксплуатации Henny Penny OFG Henny Penny OFG 79 Руководство по эксплуатации Henny Penny OFG-321 Henny Penny OFG-321 80 Руководство по эксплуатации Henny Penny OFE/OFG/OEA/OGA-341 Henny Penny OFE/OFG/OEA/OGA-341 81 Руководство по эксплуатации Henny Penny OFG-322 Henny Penny OFG-322 82 Руководство по эксплуатации Henny Penny OFE/OFG-324 Henny Penny OFE/OFG-324 83 Руководство по эксплуатации Henny Penny OFE/OFG-323 Henny Penny OFE/OFG-323 84 Руководство по эксплуатации Henny Penny OFG-321 gas Henny Penny OFG-321 gas 85 Руководство по эксплуатации Henny Penny OFG-324 Henny Penny OFG-324 86 Руководство по эксплуатации Henny Penny OG-301/302/303 Henny Penny OG-301/302/303 87 Руководство по эксплуатации Henny Penny OGA-321 Henny Penny OGA-321 88 Руководство по эксплуатации Henny Penny OFG-390 Henny Penny OFG-390 89 Руководство по эксплуатации Henny Penny OFG-391 Henny Penny OFG-391 90 Руководство по эксплуатации Henny Penny OFG-342 Henny Penny OFG-342 91 Руководство по эксплуатации Henny Penny OGA-322 Henny Penny OGA-322 92 Руководство по эксплуатации Henny Penny OG-30X Henny Penny OG-30X 93 Руководство по эксплуатации Henny Penny OGA-321 gas Henny Penny OGA-321 gas 94 Руководство по эксплуатации Henny Penny OGA-341 Henny Penny OGA-341 95 Руководство по эксплуатации Henny Penny OGA-342 Henny Penny OGA-342 96 Руководство по эксплуатации Henny Penny PFE- 590/592 Henny Penny PFE- 590/592 97 Руководство по эксплуатации Henny Penny OFG-392 Henny Penny OFG-392 98 Руководство по эксплуатации Henny Penny OGA-323 Henny Penny OGA-323 99 Руководство по эксплуатации Henny Penny PFE-592 Henny Penny PFE-592 100 Руководство по эксплуатации Henny Penny PFG-690 Henny Penny PFG-690 101 Руководство по эксплуатации Henny Penny PFG-691 Henny Penny PFG-691 102 Руководство по эксплуатации Henny Penny QSR Solutions FM03-672 Henny Penny QSR Solutions FM03-672 103 Руководство по эксплуатации Henny Penny PFE-590 Henny Penny PFE-590 104 Руководство по эксплуатации Henny Penny PFE-591 Henny Penny PFE-591 105 Руководство по эксплуатации Henny Penny PFG-600 Gas Henny Penny PFG-600 Gas 106 Руководство по эксплуатации Henny Penny PFE-561 Henny Penny PFE-561 107 Руководство по эксплуатации Henny Penny VARTOTOJO VADOVAS OFE-290 Henny Penny VARTOTOJO VADOVAS OFE-290 108 Руководство по эксплуатации Henny Penny VARTOTOJO VADOVAS OFE-292 Henny Penny VARTOTOJO VADOVAS OFE-292 109 Руководство по эксплуатации Henny Penny PFG-600 Henny Penny PFG-600 110 Руководство по эксплуатации Henny Penny Pressure Fryer Henny Penny Pressure Fryer 111 Руководство по эксплуатации Henny Penny 290 Henny Penny 290 112 Руководство по эксплуатации Henny Penny 590 Henny Penny 590 113 Руководство по эксплуатации Henny Penny EEE-141 Henny Penny EEE-141 114 Руководство по эксплуатации Henny Penny OEA-321 Henny Penny OEA-321 115 Руководство по эксплуатации Henny Penny OFE-324 Henny Penny OFE-324 116 Руководство по эксплуатации Henny Penny OFE/OFG/OEA/OGA-342 Henny Penny OFE/OFG/OEA/OGA-342 117 Руководство по эксплуатации Henny Penny OFG-323 Henny Penny OFG-323 118 Руководство по эксплуатации Henny Penny PFE-500 Henny Penny PFE-500

background image

Model HHC-990

303

4-7

5-2. ERROR CODES AND

The display shows the following error codes and warnings when a

WARNINGS

fault is detected, along with an alarm sound. Both the heat and
humidity systems shut down, except when specified otherwise.

Display

Cause

Panel Board Correction

“E-4

CPU TOO HOT”

• Control board too hot;

unit overheating or
louvers clogged

“E-5

AIR TEMP TOO HOT”

• Faulty relay, PC board,

or air probe

“E-54A CPU TEMP SENSOR

• Faulty PC board

OPEN”

“E-54B CPU TEMP SENSOR

• Faulty PC board

SHORTED”

“E-6A

AIR TEMP SENSOR

• Faulty air probe

FAILED OPEN”

• Turn switch to OFF position, then back to

ON; if display still shows “E-4”, the PC
board is getting too hot; clean louvers and
check cooling fan; if cooling fan is not
working, have it replaced; once panel
cools down, the controls should return to
normal; if “E-4” persists, have the PC
board replaced

• Turn switch to OFF position, then back to

ON; if display shows “E-5”, the heating
circuits and temperature probe should be
checked; once the unit cools down, the
controls should return to normal; if “E-5”
persists, have the PC board replaced

• Turn switch to OFF position, then back to

ON; if display shows “E-54A”, the
control should be re-initialized (see Pro-
gramming Section); if the error code
persists, have PC board replaced

• Turn switch to OFF position, then back to

ON; if display shows “E-54B”, the
control should be re-initialized (see Pro-
gramming Section); if the error code
persists, have PC board replaced

• Turn switch to OFF position, then back to

ON; if the display shows “E-6”, the
temperature probe should be checked;
once the temperature probe is repaired, or
replaced, the controls should return to
normal; if “E-6” persists, have the PC
board replaced

Источник

Many deep fryers from Henny Penny use a digital readout system called Computron 1000 or 8000. These display error codes and messages if there is something ailing the machine. But what exactly do those mean? Below is a cheat sheet with common Henny Penny error codes, so you can diagnose the problem quickly.

​

It’s important to note that if there are multiple errors, only the highest priority error will be reported. This list is in numerical order, not order of priority. Some of these errors may have a simpler fix than others (i.e. closing the drain switch). However, many errors will require more work or problem solving. Please contact us now to schedule a service call or over the phone assistance. 

  • E-4: The control board is overheating – Ensure the fryer has proper clearance and check for obstructions on the side louvers of the fryer.

  • E-5: The oil or shortening is overheating – Is a contactor or burner locked on? Switch the unit off and back on again. If the display continues to show E-5, have an authorized technician check the heating circuit and temperature probe.

  • E-6: An error has occurred with the temperature probe – It may be faulty, damaged or disconnected. E-6A means there’s an open circuit. E-6B means there is a short. Have these checked and repaired by an authorized technician.

  • E-10: The high limit has tripped on your Henny Penny Fryer – Like E-5, the oil is likely too hot. In this case, check to ensure the contactor or burner isn’t locked on. This can also occur if the unit is dry-fired or the oil level is too low. Let the unit cool down for 15 to 20 minutes, and push the reset button. If the high limit does not reset, it must be replaced by an authorized technician.

  • E-15: The drain handle is open while the fryer is on – The drain should only be opened when the fryer power switch is off. If E-15 occurs while the drain appears closed, check the drain switch.

  • E-20: An error has occurred with the gas ignition system – See errors below for more specific issues.

    • E-20A: The fan vacuum sensor is stuck closed even when the fan is off – There could be a faulty vacuum sensor or a wire short. In the normal sequence, the controller checks to see if the sensor is an open circuit before turning the draft fan on, and in the second sequence, it will verify the fan is on before closing the vacuum sensor. Check to ensure the fan isn’t running as it shouldn’t be until after that first sequence. If you press the timer button, the unit will attempt to ignite again.

    • E-20B: The fan vacuum sensor failed to close when the fan turned on – The fan or vacuum sensor may have failed or there is a broken or disconnected wire. If the fan is actually running, the vacuum sensor or vacuum hose is defective or the wiring connections to the vacuum sensor is faulty. All these will need to be checked and repaired by an authorized technician.

    • E-20C: The ignition module is not responding – This occurs when the ignition module is locked out after losing the flame four times. It is either disconnected or faulty. If this error occurs and the unit isn’t even trying to spark, there’s likely a problem with the wiring, the module itself, or the relay on the I/O board. An authorized technician will need to check and repair both issues.

    • E-20D: The unit is failing to ignite or sense the flame – Turn power off and on again. If the problem persists, check the gas line connections including the gas shut-off valve. The ignition module, gas valve, flame sensor gap, and the wiring for the valve and ignition module must be checked by an authorized technician.

  • E-41: Programming settings have been lost – This can occur if a capacitor on the CPU board fails or because of voltage spikes and dropouts. If resetting power does not fix the issue, contact an authorized technician to replace the CPU board.

  • E-46: Faulty EEPROM write error – EEPROM stands for electrically erasable programmable read-only memory. This only occurs if the EEPROM chip has failed or if the CPU board has a fault. The CPU will need to be replaced by an authorized technician.

  • E-47: The analog converter chip has experienced an Analog-to-Digital (A-to-D) failure – This indicates that the 12V supply on the I/O board failed, the analog 5V supply is bad or the A-to-D chip is bad. Check for moisture damage. Test to see if the speaker works normally by pressing a key on the control panel. If it doesn’t function, or is giving very faint sounds, then the electrical supply, I/O board and/or chip will need to be replaced by an authorized service technician.

  • E-48: There has been an Input System Error – This means the CPU can’t read buttons or digital inputs. This will need to be repaired or replaced by an authorized technician.

  • ​

If you need more assistance, check out our Henny Penny manual library or troubleshooting guide for diagnostic help.

​

Please contact our Foodservice Solutions Tech who can help with these specific units and all your commercial kitchen equipment needs.

​

​

Источник

Model EEE-141,142, 143, 144

7-2.    ERROR CODES

In the event of a control system failure, the digital display shows an
error message.  The message codes are shown in the DISPLAY
column below.  A constant tone is heard when an error code is
displayed, and to silence this tone, press any button.

DISPLAY

CAUSE

CORRECTION

“E-4”

Control board

Turn switch to OFF position, then turn switch back to ON;

overheating

if display shows “E-4”, the control board is getting too hot;
check the louvers on each side of the unit for obstructions

“E-5”

Oil

Turn switch to OFF position, then turn switch back to ON;

overheating

if display shows “E-5”, the heating circuits and temperature
probes should be checked

“E-6A”

Temperature

Turn switch to OFF position, then turn switch back to ON;

probe open

if display shows “E-6A”, the temperature probe should be
checked

“E-6B”

Temperature

Turn switch to OFF position, then turn switch back to ON;

probe shorted

if display shows “E-6B”, the temperature probe should be
checked

“E-10”

High limit

Reset the high limit by using a small screwdriver or Allen
wrench gently pushing it into the hole in the heating element
hinge; if high limit does not reset, high limit may need be replaced

“E-15”

Drain switch

Make sure drain knob is completely pushed-in; if E-15 persists,
have drain switch checked

“E-18-A”

Left level sensor open

Turn switch to OFF position, then turn switch back to ON;

“E-18-B”

Right level sensor open

if display still indicates a failed sensor, have the connectors checked

“E-18-C”

Both level sensors open at the control board; have sensor checked & replace if necessory

209

       7-3

Источник

Понравилась статья? Поделить с друзьями:
  • Helper exe ошибка приложения
  • Hearts of iron 4 ошибка установки
  • Hearts of iron 4 ошибка при установке
  • Hearts of iron 4 ошибка запуска
  • Hearts of iron 4 ошибка 0xc000007b