Iveco Stralis (Ивеко Стралис) Ошибки RFC | EuroTruck.su
Дата создания: 19 Apr
0 Комментарий.
Iveco Stralis (Ивеко Стралис) Ошибки RFC (Rear Frame Computer)
DTC/FMI | Тип ошибки | Способы ремонта Ивеко Стралис |
01/06 | Короткое замыкание выхода RFC | Проверить электропроводку. |
02/06 | Короткое замыкание правых и левых габаритных фонарей прицепа | Проверить габаритные фонари прицепа |
03/06 | Короткое замыкание правых и левых габаритных фонарей прицепа | Проверить габаритные фонари прицепа |
05/05 | Обрыв цепи стоп-сигналов прицепа | Проверить разъем на прицеп. Проверить лампочки прицепа. Проверить электропроводку прицепа. |
05/06 | Короткое замыкание стоп-сигналов прицепа. | Проверить разъем на прицеп. Проверить лампочки прицепа. Проверить электропроводку прицепа. |
06/05 | Обрыв цепи фонарей заднего хода прицепа | Проверить разъем на прицеп. Проверить лампочки прицепа. Проверить электропроводку прицепа. |
06/06 | Короткое замыкание фонарей заднего хода прицепа. | Проверить разъем на прицеп. Проверить лампочки прицепа. Проверить электропроводку прицепа. |
07/06 | Короткое замыкание обмотки клапана коробки отбора мощности. | Проверить разъем на коробке отбора мощности. Проверить электроклапан. |
08/05 | Обрыв цепи правого указателя поворота прицепа. | Проверить разъем на прицеп. Проверить лампочки прицепа. Проверить электропроводку прицепа. |
08/06 | Короткое замыкание правого указателя поворота прицепа. | Проверить разъем на прицеп. Проверить лампочки прицепа. Проверить электропроводку прицепа. |
09/00 | Ошибка показания датчика давления в ресивере выше максимального. | Проверить датчик давления на четырехконтурном клапане. Проверить электропроводку. Убедиться в том, что пневмосистема не замерзла. |
0А/01 | Ошибка показания датчика давления в ресивере выше максимального. | Проверить датчик давления на четырехконтурном клапане. Проверить электропроводку. Убедиться в том, что пневмосистема не замерзла. |
0B/00 | Питание датчика давления пневмосистемы больше макс. | Проверить датчик давления на четырехконтурном клапане. Проверить питание(5в). |
0В/01 | Питание датчика давления пневмосистемы больше мин. | Проверить датчик давления на четырехконтурном клапане. Проверить питание(5в). |
0С/00 | Ошибка показания датчика уровня топлива больше макс. | Проверить разъем на датчике уровня топлива. Проверить электропроводку. |
0С/01 | Ошибка показания датчика уровня топлива больше мин. | Проверить разъем на датчике уровня топлива. Проверить электропроводку. |
0D/05 | Обрыв цепи фонарей рабочего света. | Проверить лампочки. Проверить электропроводку. |
0D/06 | Короткое замыкание фонарей рабочего света. | Проверить лампочки. Проверить электропроводку. |
0E/05 | Обрыв цепи правого указателя поворота. | Проверить разъем на прицеп. Проверить лампочки прицепа. Проверить электропроводку прицепа. |
0E/06 | Обрыв цепи левого указателя поворота. | Проверить разъем на прицеп. Проверить лампочки прицепа. Проверить электропроводку прицепа. |
0F/05 | Обрыв цепи противотуманных фонарей прицепа. | Проверить разъем на прицеп. Проверить лампочки прицепа. Проверить электропроводку прицепа. |
0F/06 | Короткое замыкание противотуманных фонарей прицепа. | Проверить разъем на прицеп. Проверить лампочки прицепа. Проверить электропроводку прицепа. |
10/04 | Не горит освещение с левой стороны автомобиля. | Проверить лампочки. Проверить электропроводку. |
11/04 | Не горит освещение с правой стороны автомобиля. | Проверить лампочки. Проверить электропроводку. |
16/05 | Обрыв цепи левого стоп-сигнала прицепа. | Проверить разъем на прицеп. Проверить лампочки прицепа. Проверить электропроводку прицепа. |
16/06 | Короткое замыкание левого стоп-сигнала прицепа. | Проверить разъем на прицеп. Проверить лампочки прицепа. Проверить электропроводку прицепа. |
17/05 | Обрыв цепи противотуманных фонарей прицепа. | Проверить разъем на прицеп. Проверить лампочки прицепа (21w). Проверить электропроводку прицепа. |
17/06 | Короткое замыкание противотуманных фонарей прицепа. | Проверить разъем на прицеп. Проверить лампочки прицепа (21w). Проверить электропроводку прицепа. |
17/12 | Плохое питание противотуманных фонарей прицепа. | Проверить разъем на прицеп. Проверить лампочки прицепа (21w). Проверить электропроводку прицепа. |
18/05 | Обрыв цепи правого стоп-сигнала прицепа. | Проверить разъем на прицеп. Проверить лампочки прицепа. Проверить электропроводку прицепа. |
18/06 | Короткое замыкание правого стоп-сигнала прицепа. | Проверить разъем на прицеп. Проверить лампочки прицепа. Проверить электропроводку прицепа. |
1B/05 | Обрыв цепи правого заднего стояночного фонаря. | Проверить лампочки. Проверить электропроводку. |
1B/06 | Короткое замыкание правого заднего стояночного фонаря. | Проверить лампочки. Проверить электропроводку. |
1B/12 | Слабый ток в цепи правого заднего стояночного фонаря. | Проверить лампочки. Проверить электропроводку. |
1С/05 | Обрыв цепи электромагнита разблокировки дифференциала. | Проверить разъем на электроклапан. Проверить электроклапан. |
1С/06 | Короткое замыкание электромагнита разблокировки дифференциала. | Проверить разъем на электроклапан. Проверить электроклапан. |
1D/05 | Обрыв цепи фонаря заднего хода | Проверить лампочки. Проверить электропроводку. |
1D/06 | Короткое замыкание фонаря заднего хода | Проверить лампочки. Проверить электропроводку. |
1D/12 | Слабый ток в цепи фонаря заднего хода | Проверить лампочки. Проверить электропроводку. |
1E/05 | Обрыв цепи задних габаритных фонарей | Проверить лампочки. Проверить электропроводку. |
1E/06 | Короткое замыкание задних габаритных фонарей | Проверить лампочки. Проверить электропроводку. |
1E/12 | Слабый ток в цепи задних габаритных фонарей | Проверить лампочки. Проверить электропроводку. |
20/00 |
Не верное показание датчика износа колодок левого колеса третьей оси. | Проверить датчика износа колодок. Проверить электропроводку. |
20/01 |
Не верное показание датчика износа колодок левого колеса третьей оси. | Проверить датчика износа колодок. Проверить электропроводку. |
21/00 |
Не верное показание датчика износа колодок правого колеса третьей оси. | Проверить датчика износа колодок. Проверить электропроводку. |
21/01 |
Не верное показание датчика износа колодок правого колеса третьей оси. | Проверить датчика износа колодок. Проверить электропроводку. |
22/02 | Ошибка канала связи BCB. | Проверить линию CAN BCB |
23/02 | Ошибка синхронизации указателей поворотов и аварийной сигнализации. | Проверить линию CAN между FFC и RFC |
-
max10.84
- Сообщения: 524
- Зарегистрирован: Ср фев 13, 2013 11:53 pm
- Откуда: Россия,Вязьма
Iveco stralis 2006 , подозрение на неисправность блока RFC.
В один момент, отказало половина внешних световых приборов на прицепе и тягаче. Оказалось, что сгорел оранжевый предохранитель №2(RFC питание левых задних фонарей) в блоке возле АКБ. Были ошибки по КЗ стопов прицепа и еще целая куча по габаритам, поворотам. Причину толком не нашли, был плохой контакт массы в розетке прицепа и в фонарях стояло по две лампы на стопы(стопы + ПТФ).Предохранитель заменили и после этого стопы на прицепе горят постоянно, без зажигания и без нажатия на тормоз. На тягаче стопы работают нормально, в RFC висит ошибка 05 05 — стоп-сигнал прицепа обрыв. Провод от RFC до розетки прицепа доходит, с плюсом, массой и другими контактами розетки прицепа не звонится. Получается что-то выгорело внутри блока?
-
syava
- Сообщения: 3560
- Зарегистрирован: Ср май 14, 2008 5:29 pm
- Откуда: Украина г.Луцк
- Контактная информация:
-
igor-dvs73
- Сообщения: 566
- Зарегистрирован: Пн июн 17, 2013 10:03 pm
- Откуда: Россия,Валдай
Re: Iveco stralis 2006 , подозрение на неисправность блока R
Сообщение
igor-dvs73 » Вт сен 08, 2015 11:34 pm
На Iveco Stralis,чтобы проверить проводку,например фонари-стопы- прочее,нуна кусок от RFC до всех конечных инстанций прошерстить. Желательно,сняв с авто. Бывает один провод в пяти местах оборван.При этом по поры-до времени всё арбайтен,как ни странно.На Iveco действует Закон взаимопомощи соседних проводов.Впрочем,они с MAN родственники в этом.Как-то на MAN TGA закосячил задний фонарь. При этом он светился и моргал,как новогодняя ёлка,капризничал в движении и сигналил при нажатии на тормоз. Так что,ещё до проводки раз докопайтесь,включая сами фонари. А RFC сам как предохранитель работает.Чтобы спалить,надо постараться…я так думаю.
-
max10.84
- Сообщения: 524
- Зарегистрирован: Ср фев 13, 2013 11:53 pm
- Откуда: Россия,Вязьма
Re: Iveco stralis 2006 , подозрение на неисправность блока R
Сообщение
max10.84 » Ср сен 09, 2015 1:19 am
Да можно еще проверить досконально, но мне кажется, что внутри блока сгорел накоротко транзистор или через что там питание подается, поэтому и светятся стопы постоянно. Плюс по-любому идет с контакта блока. Не догадался я на самом блоке контакт на стопы прицепа прозвонить с плюсовыми контактами. Если будет звонится(особенно с контактом от сгоревшего преда) без сопротивления, то наверно действительно кирдык блоку. Единственное, что врядли блок сам по себе сломался от старости, где-то все же косяк притаился.
-
max10.84
- Сообщения: 524
- Зарегистрирован: Ср фев 13, 2013 11:53 pm
- Откуда: Россия,Вязьма
Re: Iveco stralis 2006 , подозрение на неисправность блока R
Сообщение
max10.84 » Сб сен 12, 2015 10:24 pm
Нашлась причина в проводке прицепа, провод стоп-сигнала немного перетерся и изредка ерзал по железу. Машина какое-то время так и ездила(стопы пропадали на прицепе) до перегорания предохранителя. Только тогда начали искать причину, но блок видимо уже подломался. Так постоянный плюс и висит на выходе «стоп прицепа». Поставили в разрыв этого провода реле с предохранителем на 15 А, управление от стоп-сигнала тягача.
Проводку перепроверил, все в порядке, ошибка по стопам прицепа больше не появляется.
Вернуться в «Вопросы, не подходящие к предложенным разделам»
Перейти
- WWW.TRUCK-DIAGNOST.COM
- ↳ ПОМОЩЬ ПЕРЕВОЗЧИКАМ. ТЕХНИЧЕСКИЕ КОНСУЛЬТАЦИИ
- ↳ ПОЛЕЗНАЯ ТЕХНИЧЕСКАЯ ИНФОРМАЦИЯ ДЛЯ ПЕРЕВОЗЧИКОВ
- ↳ Обучение диагностике грузовых автомобилей, автобусов, прицепов
- ↳ Техническая документация. Схемы.
- ↳ Оборудование для диагностики грузовиков, автобусов, прицепов
- ↳ Программное обеспечение для диагностики и чип-тюнинга
- ↳ Системы управления двигателями EDC — Electronic Diesel Control
- ↳ Топливные системы Common Rail
- ↳ Топливные системы с насос-форсунками PLD, PDE
- ↳ Топливные системы с ТНВД (рядными, ротационными)
- ↳ Системы снижения токсичности AdBlue, Denoxtronic, SCR, Bluetec, EAS и др.
- ↳ Система подготовки и подачи сжатого воздуха, ECAM, EAC, APM и др.
- ↳ Пневматическая тормозная система
- ↳ ABS/ASR — антиблокировочная и противобуксовочная системы
- ↳ EBS/EPB — электронно-пневматическая тормозная система
- ↳ Пневматическая подвеска
- ↳ ECAS/ELC — электронно-пневматическая подвеска
- ↳ Управление приводом сцепления
- ↳ Управление КПП: EPS, AS-Tronic, Opticruise, Optidriver, I-Shift и др.
- ↳ Бортовые компьютеры, координаторы: ZBR, VIC, FFR, COO и др.
- ↳ Электронные системы управления техническим обслуживанием
- ↳ Тахографы
- ↳ Автономные отопители WEBASTO, EBERSPACHER
- ↳ Диагностика и устранение неисправностей
- ↳ Ремонт электронных блоков управления
- ↳ Дополнительное оборудование
- ↳ Вопросы качества и гарантии
- ↳ Деловые контакты
- ↳ Вопросы, не подходящие к предложенным разделам
- ↳ Вопросы и предложения по работе форума WWW.TRUCK-DIAGNOST.COM
- ↳ Новости форума WWW.TRUCK-DIAGNOST.COM
STRALIS
ЭЛЕКТРОННОЕ ОБОРУДОВАНИЕ III.31
ЭБУ ЗАДНЕГО КОНТУРА ЭЛЕКТРОННОГО ОБОРУДОВАНИЯ (RFC )
Модуль RFC расположен в центральной части автомобиля, с правой стороны. Порядок снятия модуля RFC аналогичен поряд>
ку снятия электронного блока FFC.
А. Электронный блок управления RFC
III.32 ЭЛЕКТРОННОЕ ОБОРУДОВАНИЕ
STRALIS
Поз.
Описание
Код êомпонента
Цветовой êод
провода
1 Резерв
—
—
2 Положительная цепь питания
—
8871
3 Плюс правоãо ãабаритноãо фонаря/прицепа
33004
3330
4 Плюс левоãо ãабаритноãо фонаря/прицепа
33004
3339
A
5 Положительная цепь питания
—
8871
6 Плюс для стоп-сиãналов прицепа
72010
1179
7 Плюс для фонарей заднеãо хода прицепа
72010
2226
8 Плюс на элеêтроêлапаны вêлючения на полнóю мощность êоробêи
отбора мощности на êоробêе передач
78208
9954
1 Резерв
—
—
2 Резерв
—
—
3 Минóс от выêлючателя блоêировêи пóсêа двиãателя при вêлюченной
передаче
53508
8050
4 Минóс выêлючателя фонарей заднеãо хода
53503
2268
5 Минóс выêлючателя êонтрольной лампы пониженноãо ряда передач
53507
9992
6 Минóс выêлючателя êонтрольной лампы засорения воздóшноãо фильтра
42351
6663
7 Плюс на правый óêазатель поворота прицепа
72010
1185
8 Резерв
—
—
9 Плюс на наãревательный элемент фильтра-осóшителя воздóха
61104
5562
10 Сиãнал вêлючения наãревательноãо элемента фильтра-осóшителя воздóха
44031
5561
11 Минóс выêлючателя сиãнализации неисправности тормозной системы
прицепа
42111
6689
12 Резерв
—
—
13 Плюс на наãревательный элемент фильтра-осóшителя воздóха тормозной
системы
61104
5560
14 Плюс от датчиêа óровня топлива
44031
5557
15 Резерв
—
—
16 Плюс фонаря освещения сцепноãо óстройства
34011
2224
B
17 Плюс (возврат) от датчиêа óровня топлива
44031
5555
18 Резерв
—
—
19 Резерв
—
—
20 Резерв
—
—
21 Резерв
—
—
22 Резерв
—
—
23 Резерв
—
—
24 Плюс на правые óêазатели поворота прицепа
72010
1180
25 Резерв
—
—
26 Резерв
—
—
27 Резерв
—
—
28 Резерв
—
—
29 Резерв
—
—
30 Сиãнал от датчиêа наличия воды в топливном фильтре
86013
5530
31 Минóс от выêлючателя êонтрольной лампы задней êоробêи отбора
мощности
53568
0131
32 Плюс на задние противотóманные фонари прицепа
72010
2283
RFC (на раме шасси)
Разъем «J1»
STRALIS
ЭЛЕКТРОННОЕ ОБОРУДОВАНИЕ III.33
Поз.
Описание
Код êомпонента
Цветовой êод
провода
1 Плюс от предохранителя для питания световых приборов, левая сторона
автомобиля
70000
7902
2 Плюс от предохранителя для питания световых приборов, левая сторона
автомобиля
70000
7902
3 Плюс от предохранителя для питания световых приборов, правая
сторона автомобиля
70000
7901
4 Плюс от предохранителя для питания световых приборов, левая сторона
автомобиля
70000
7902
A
5 Плюс от предохранителя для питания световых приборов, правая
сторона автомобиля
70000
7901
6 Плюс на нарóжные осветительные приборы
—
3333
7 Масса рамы шасси
—
0000
8 Плюс от предохранителя для питания световых приборов, правая
сторона автомобиля
70000
7901
1 Линия CAN — H (ВCB)
—
БЕЛЫЙ
2 Линия CAN — L (ВCB)
—
ЗЕЛЕНЫЙ
3 Резерв
—
БЕЛЫЙ
4 Резерв
—
ЗЕЛЕНЫЙ
5 Плюс на задние левые ãабаритные фонари
34000
1120
6 Линия K (Диаãностичесêий разъем)
72021
2999
7 Минóс от замêа зажиãания
—
0987
8 Плюс на левые стоп-сиãналы
34000
1175
9 Резерв
—
—
10 Плюс на задние противотóманные фонари
34000
2283
11 Минóс от вторичноãо выêлючателя оãраничителя сêорости
—
0172
12 Минóс от датчиêа износа тормозных êолодоê третьей оси
86003
6664
13 Плюс для правоãо стоп-сиãнала
34000
1175
14 Плюс на ãабаритный фонарь задний правый
34000
1125
15 Плюс на ãабаритный фонарь задний правый
34000
3307
16 Плюс на ãабаритный фонарь стояночный правый
34000
3315
B
17 Резерв
—
—
18 Резерв
—
—
19 Минóс от выêлючателя êонтрольной лампы межосевой блоêировêи
дифференциала
53521
6603
20 Минóс от датчиêа износа тормозных êолодоê заднеãо моста
86003
6667
21 Резерв
—
—
22 Сиãнал от датчиêа износа тормозных êолодоê третьей оси
88011
6037
23 Минóс от переêлючателя межêолесной блоêировêи дифференциала
53801
0041
24 Сиãнал от датчиêа износа тормозных êолодоê третьей оси
88011
6035
25 —
—
—
26 Плюс для фонаря заднеãо хода
34000
2226
27 Плюс на ãабаритный фонарь задний левый
34000
3306
28 Плюс на ãабаритный фонарь стояночный левый
34000
3305
29 Минóс от выêлючателя сиãнализации неисправности ãидросистемы
третьей óправляемой оси
53591
0491
30 Минóс от переêлючателя межêолесной блоêировêи дифференциала
53801
0040
31 Резерв
—
32 Резерв
—
RFC
Разъем «J2»
III.34 ЭЛЕКТРОННОЕ ОБОРУДОВАНИЕ
STRALIS
МОДУЛЬ ДВЕРИ ВОДИТЕЛЯ (DDM)/ МОДУЛЬ ДВЕРИ ПАССАЖИРА (PDM)/ МОДУЛЬ КАБИНЫ (CM)
Эти данные три электронных модуля идентичны.
DDM установлен внутри двери водителя, PDM установлен внутри двери пассажира.
Модуль кабины находится в отсеке под приборной панелью справа, там же где и ЭБУ АБС и ECAS.
Единственное различие между DDM и PDM заключается в том, что у последнего контакт 52/10 и 51/8 соединены перемыч>
кой для идентификации данного ЭБУ в качестве модуля пассажирской двери.
Модуль кабины управляет электрооборудованием кабины (таким как омыватели фар, солнцезащитные шторки и т. п.).
Входы
Выходы
Обоãрев зерêал заднеãо вида
Обоãрев зерêал заднеãо вида
Реãóлировêа зерêал заднеãо вида
Реãóлировêа зерêал заднеãо вида
Стеêлоподъемниêи
Стеêлоподъемниêи
Центральный замоê
Центральный замоê
ECU Name |
SPN [Hex] |
Fault Component |
Description |
FMI [DEC] |
FMI [HEX] |
FMI Description |
Lamp status |
Comment |
ABS Wabco D |
40B01 |
Wheel sensor left front fault. |
air gap too large, sensor output voltage too low but just exceeds trigger level |
1 |
01 |
air gap |
ABS: wheel disabled ASR: disabled |
|
ABS Wabco D |
40B01 |
Wheel sensor left front fault. |
such proportion of tyre diameter/ pole wheel teeth number that wheel speed difference within front axle > 10 % or difference within wheels of different axles > 19 % . Pneus or number of polewheel teeth are different. Check wheel circumference and number of polewheel |
2 |
02 |
incorrect tyre or pole wheel |
ABS: wheel disabled ASR: disabled |
|
ABS Wabco D |
40B01 |
Wheel sensor left front fault. |
DC voltage detected. Short circuit or impedance to battery voltage. |
3 |
03 |
Short to Battery |
ABS: wheel disabled ASR: disabled |
|
ABS Wabco D |
40B01 |
Wheel sensor left front fault. |
Short circuit to ground is detected. |
4 |
04 |
Short to Ground |
ABS: wheel disabled ASR: disabled |
|
ABS Wabco D |
40B01 |
Wheel sensor left front fault. |
Open circuit is detected |
5 |
05 |
open circuit |
ABS: wheel disabled ASR: disabled |
|
ABS Wabco D |
40B01 |
Wheel sensor left front fault. |
Short circuit between sensorwires IG/IGM is detected |
6 |
06 |
Short circuit |
ABS: wheel disabled ASR: disabled |
|
ABS Wabco D |
40B01 |
Wheel sensor left front fault. |
Cyclic drop out detected at speed higher than 10 km/h. Several wheel revolution necessary. |
7 |
07 |
incorrect pole wheel |
ABS: wheel disabled ASR: disabled |
|
ABS Wabco D |
40B01 |
Wheel sensor left front fault. |
16 sec. slip duration detected. |
8 |
08 |
slip |
ABS: wheel disabled ASR: disabled |
|
ABS Wabco D |
40B01 |
Wheel sensor left front fault. |
Wire IG or IGM of another sensor is detected. |
9 |
09 |
wires mismatched |
ABS: wheel disabled ASR: disabled |
|
ABS Wabco D |
40B01 |
Wheel sensor left front fault. |
Temporarily loss of wheel speed signal. Air gap too large, sensor voltage |
10 |
0A |
speed drop-out |
ABS: wheel disabled |
|
exceeds trigger level at too late. |
ASR: disabled |
|||||||
ABS Wabco D |
40B01 |
Wheel sensor left front fault. |
Brake squeezes or chatters. |
11 |
0B |
abnormal speed (chatter)not stored |
ABS: partial disabled ASR: disabled with standard parameter set not as fault interpretated FMI 11 not stored |
|
ABS Wabco D |
40B01 |
Wheel sensor left front fault. |
Not plausible sensor frequency measured |
12 |
0C |
frequency too high |
ABS: wheel disabled ASR: disabled |
|
ABS Wabco D |
40B02 |
Wheel sensor right front fault |
air gap too large, sensor output voltage too low but just exceeds trigger level |
1 |
01 |
air gap |
ABS: wheel disabled ASR: disabled |
|
ABS Wabco D |
40B02 |
Wheel sensor right front fault |
such proportion of tyre diameter/ pole wheel teeth number that wheel speed difference within front axle > 10 % or difference within wheels of different axles > 19 % . Pneus or number of polewheel teeth are different. Check wheel circumference and number of polewheel |
2 |
02 |
incorrect tyre or pole wheel |
ABS: wheel disabled ASR: disabled |
|
ABS Wabco D |
40B02 |
Wheel sensor right front fault |
DC voltage detected. Short circuit or impedance to battery voltage. |
3 |
03 |
Short to Battery |
ABS: wheel disabled ASR: disabled |
|
ABS Wabco D |
40B02 |
Wheel sensor right front fault |
Short circuit to ground is detected. |
4 |
04 |
Short to Ground |
ABS: wheel disabled ASR: disabled |
|
ABS Wabco D |
40B02 |
Wheel sensor right front fault |
Open circuit is detected |
5 |
05 |
open circuit |
ABS: wheel disabled ASR: disabled |
|
ABS Wabco D |
40B02 |
Wheel sensor right front fault |
Short circuit between sensorwires IG/IGM is detected |
6 |
06 |
Short circuit |
ABS: wheel disabled ASR: disabled |
|
ABS Wabco D |
40B02 |
Wheel sensor right front fault |
Cyclic drop out detected at speed higher than 10 km/h. Several wheel revolution necessary. |
7 |
07 |
incorrect pole wheel |
ABS: wheel disabled ASR: disabled |
|
ABS Wabco D |
40B02 |
Wheel sensor right front fault |
16 sec. slip duration detected. |
8 |
08 |
slip |
ABS: wheel disabled ASR: disabled |
|
ABS Wabco D |
40B02 |
Wheel sensor right front fault |
Wire IG or IGM of another sensor is detected. |
9 |
09 |
wires mismatched |
ABS: wheel disabled |
|
ASR: disabled |
||||||||
ABS Wabco D |
40B02 |
Wheel sensor right front fault |
Temporarily loss of wheel speed signal. Air gap too large, sensor voltage exceeds trigger level at too late. |
10 |
0A |
speed drop-out |
ABS: wheel disabled ASR: disabled |
|
ABS Wabco D |
40B02 |
Wheel sensor right front fault |
Brake squeezes or chatters. |
11 |
0B |
abnormal speed (chatter)not stored |
ABS: partial disabled ASR: disabled with standard parameter set not as fault interpretated FMI 11 not stored |
|
ABS Wabco D |
40B02 |
Wheel sensor right front fault |
Not plausible sensor frequency measured |
12 |
0C |
frequency too high |
ABS: wheel disabled ASR: disabled |
|
ABS Wabco D |
40B03 |
Wheel sensor left rear fault |
air gap too large, sensor output voltage too low but just exceeds trigger level |
1 |
01 |
air gap |
ABS: wheel disabled ASR: disabled |
|
ABS Wabco D |
40B03 |
Wheel sensor left rear fault |
such proportion of tyre diameter/ pole wheel teeth number that wheel |
2 |
02 |
incorrect tyre or pole wheel |
ABS: wheel disabled |
|
speed difference within front axle > 10 % or difference within wheels of different axles > 19 % . Pneus or number of polewheel teeth are different. Check wheel circumference and number of polewheel |
ASR: disabled |
|||||||
ABS Wabco D |
40B03 |
Wheel sensor left rear fault |
DC voltage detected. Short circuit or impedance to battery voltage. |
3 |
03 |
Short to Battery |
ABS: wheel disabled ASR: disabled |
|
ABS Wabco D |
40B03 |
Wheel sensor left rear fault |
Short circuit to ground is detected. |
4 |
04 |
Short to Ground |
ABS: wheel disabled ASR: disabled |
|
ABS Wabco D |
40B03 |
Wheel sensor left rear fault |
Open circuit is detected |
5 |
05 |
open circuit |
ABS: wheel disabled ASR: disabled |
|
ABS Wabco D |
40B03 |
Wheel sensor left rear fault |
Short circuit between sensorwires IG/IGM is detected |
6 |
06 |
Short circuit |
ABS: wheel disabled ASR: disabled |
|
ABS Wabco D |
40B03 |
Wheel sensor left rear fault |
Cyclic drop out detected at speed higher than 10 km/h. Several wheel |
7 |
07 |
incorrect pole wheel |
ABS: wheel disabled |
|
revolution necessary. |
ASR: disabled |
|||||||
ABS Wabco D |
40B03 |
Wheel sensor left rear fault |
16 sec. slip duration detected. |
8 |
08 |
slip |
ABS: wheel disabled ASR: disabled |
|
ABS Wabco D |
40B03 |
Wheel sensor left rear fault |
Wire IG or IGM of another sensor is detected. |
9 |
09 |
wires mismatched |
ABS: wheel disabled ASR: disabled |
|
ABS Wabco D |
40B03 |
Wheel sensor left rear fault |
Temporarily loss of wheel speed signal. Air gap too large, sensor voltage exceeds trigger level at too late. |
10 |
0A |
speed drop-out |
ABS: wheel disabled ASR: disabled |
|
ABS Wabco D |
40B03 |
Wheel sensor left rear fault |
Brake squeezes or chatters. |
11 |
0B |
abnormal speed (chatter)not stored |
ABS: wheel disabled ASR: disabled |
|
ABS Wabco D |
40B03 |
Wheel sensor left rear fault |
Not plausible sensor frequency measured |
12 |
0C |
frequency too high |
ABS: wheel disabled ASR: disabled |
|
ABS Wabco D |
40B04 |
Wheel sensor right rear fault |
air gap too large, sensor output voltage too low but just exceeds trigger |
1 |
01 |
air gap |
ABS: wheel disabled |
|
level |
ASR: disabled |
|||||||
ABS Wabco D |
40B04 |
Wheel sensor right rear fault |
such proportion of tyre diameter/ pole wheel teeth number that wheel speed difference within front axle > 10 % or difference within wheels of different axles > 19 % . Pneus or number of polewheel teeth are different. Check wheel circumference and number of polewheel |
2 |
02 |
incorrect tyre or pole wheel |
ABS: wheel disabled ASR: disabled |
|
ABS Wabco D |
40B04 |
Wheel sensor right rear fault |
DC voltage detected. Short circuit or impedance to battery voltage. |
3 |
03 |
Short to Battery |
ABS: wheel disabled ASR: disabled |
|
ABS Wabco D |
40B04 |
Wheel sensor right rear fault |
Short circuit to ground is detected. |
4 |
04 |
Short to Ground |
ABS: wheel disabled ASR: disabled |
|
ABS Wabco D |
40B04 |
Wheel sensor right rear fault |
Open circuit is detected |
5 |
05 |
open circuit |
ABS: wheel disabled ASR: disabled |
|
ABS Wabco D |
40B04 |
Wheel sensor right rear fault |
Short circuit between sensorwires IG/IGM is detected |
6 |
06 |
Short circuit |
ABS: wheel disabled ASR: disabled |
|
ABS Wabco D |
40B04 |
Wheel sensor right rear fault |
Cyclic drop out detected at speed higher than 10 km/h. Several wheel revolution necessary. |
7 |
07 |
incorrect pole wheel |
ABS: wheel disabled ASR: disabled |
|
ABS Wabco D |
40B04 |
Wheel sensor right rear fault |
16 sec. slip duration detected. |
8 |
08 |
slip |
ABS: wheel disabled ASR: disabled |
|
ABS Wabco D |
40B04 |
Wheel sensor right rear fault |
Wire IG or IGM of another sensor is detected. |
9 |
09 |
wires mismatched |
ABS: wheel disabled ASR: disabled |
|
ABS Wabco D |
40B04 |
Wheel sensor right rear fault |
Temporarily loss of wheel speed signal. Air gap too large, sensor voltage exceeds trigger level at too late. |
10 |
0A |
speed drop-out |
ABS: wheel disabled ASR: disabled |
|
ABS Wabco D |
40B04 |
Wheel sensor right rear fault |
Brake squeezes or chatters. |
11 |
0B |
abnormal speed (chatter)not stored |
ABS: wheel disabled ASR: disabled |
|
ABS Wabco D |
40B04 |
Wheel sensor right rear fault |
Not plausible sensor frequency measured |
12 |
0C |
frequency too high |
ABS: wheel disabled ASR: disabled |
|
ABS Wabco D |
40B07 |
Modulator left front failure |
DC voltage detected. Short circuit or impedance to battery voltage. |
3 |
03 |
Short to Battery |
ABS: disabled ASR: disabled SMR: disabled EBL: disabled |
|
ABS Wabco D |
40B07 |
Modulator left front failure |
Open circuit is detected |
5 |
05 |
open circuit |
ABS: wheel disabled |
|
ABS Wabco D |
40B07 |
Modulator left front failure |
Short circuit between sensorwires IG/IGM is detected |
6 |
06 |
Short to Ground |
ABS: wheel disabled |
|
ABS Wabco D |
40B08 |
Modulator right front failure |
DC voltage detected. Short circuit or impedance to battery voltage. |
3 |
03 |
Short to Battery |
ABS: disabled ASR: disabled SMR: disabled EBL: disabled |
|
ABS Wabco D |
40B08 |
Modulator right front failure |
Open circuit is detected |
5 |
05 |
open circuit |
ABS: wheel disabled |
|
ABS Wabco D |
40B08 |
Modulator right front failure |
Short circuit between sensorwires IG/IGM is detected |
6 |
06 |
Short to Ground |
ABS: wheel disabled |
|
ABS Wabco D |
40B09 |
Modulator left rear failure |
DC voltage detected. Short circuit or impedance to battery voltage. |
3 |
03 |
Short to Battery |
ABS: disabled ASR: disabled SMR: disabled EBL: disabled |
|
ABS Wabco D |
40B09 |
Modulator left rear failure |
Open circuit is detected |
5 |
05 |
open circuit |
ABS: wheel disabled ASR: Diff brake disabled SMR: disabled EBL: wheel disabled |
|
ABS Wabco D |
40B09 |
Modulator left rear failure |
Short circuit between sensorwires IG/IGM is detected |
6 |
06 |
Short to Ground |
ABS: wheel disabled ASR: Diff brake disabled SMR: disabled EBL: wheel disabled |
|
ABS Wabco D |
40B0A |
Modulator right rear failure |
DC voltage detected. Short circuit or impedance to battery voltage. |
3 |
03 |
Short to Battery |
ABS: disabled ASR: disabled SMR: disabled EBL: disabled |
|
ABS Wabco D |
40B0A |
Modulator right rear failure |
Open circuit is detected |
5 |
05 |
open circuit |
ABS: wheel disabled ASR: Diff brake disabled SMR: disabled EBL: wheel disabled |
|
ABS Wabco D |
40B0A |
Modulator right rear failure |
Short circuit between sensorwires IG/IGM is detected |
6 |
06 |
Short to Ground |
ABS: wheel disabled ASR: Diff brake disabled SMR: disabled EBL: wheel disabled |
|
ABS Wabco D |
40B0D |
DBR, Retarder |
DC voltage detected. Short circuit or impedance to battery voltage. |
3 |
03 |
Short to Battery |
DBR control disabled |
|
ABS Wabco D |
40B0D |
DBR, Retarder |
Open circuit is detected |
5 |
05 |
open circuit |
DBR control disabled |
|
ABS Wabco D |
40B0D |
DBR, Retarder |
Short circuit between sensorwires IG/IGM is detected |
6 |
06 |
Short to Ground |
DBR control disabled |
|
ABS Wabco D |
40B0E |
ABS error |
Short circuit to ground is detected. |
4 |
04 |
Voltage, low voltage/open circuit |
ABS: disabled ASR: disabled SMR: disabled EBL: disabled |
|
ABS Wabco D |
40B0E |
ABS error |
Open circuit is detected |
5 |
05 |
WL-Ground |
ABS: disabled ASR: disabled SMR: disabled EBL: disabled |
|
ABS Wabco D |
40B0E |
ABS error |
Cyclic drop out detected at speed higher than 10 km/h. Several wheel revolution necessary. |
7 |
07 |
Valve Relay |
ABS: disabled ASR: disabled SMR: disabled EBL: disabled |
|
ABS Wabco D |
40B0F |
ABS error |
DC voltage detected. Short circuit or impedance to battery voltage. |
3 |
03 |
Voltage, low voltage/open circuit |
Dif&aux output disabled ASR: Diff brake disabled |
ECU Name |
SPN [Hex] |
Fault Component |
Description |
FMI [DEC] |
FMI [HEX] |
FMI Description |
Lamp status |
Comment |
ABS Wabco D |
40B0F |
ABS error |
Short circuit to ground is detected. |
4 |
04 |
Voltage, low voltage/open circuit |
ABS: disabled ASR: disabled SMR: disabled EBL: disabled |
|
ABS Wabco D |
40B0F |
ABS error |
Open circuit is detected |
5 |
05 |
WL-Ground |
Dif&aux output disabled ASR: Diff brake disabled |
|
ABS Wabco D |
40B0F |
ABS error |
Short circuit between sensorwires IG/IGM is detected |
6 |
06 |
Short to Ground |
||
ABS Wabco D |
40B0F |
ABS error |
Cyclic drop out detected at speed higher than 10 km/h. Several wheel revolution necessary. |
7 |
07 |
Valve Relay |
ABS: disabled ASR: disabled SMR: disabled EBL: disabled |
|
ABS Wabco D |
40B10 |
ABS error |
DC voltage detected. Short circuit or impedance to battery voltage. |
3 |
03 |
Voltage, low voltage/open circuit |
EBL: starts depending from deceleration |
|
ABS Wabco D |
40B10 |
ABS error |
Open circuit is detected |
5 |
05 |
Brake input open or shorted to ground |
EBL: starts depending from deceleration |
|
ABS Wabco D |
40B12 |
ABS error |
DC voltage detected. Short circuit or impedance to battery voltage. |
3 |
03 |
Diff. Brake Valve, shorted to UBATT |
ASR: Diff brake disabled |
|
ABS Wabco D |
40B12 |
ABS error |
Open circuit is detected |
5 |
05 |
Diff. Brake Valve, open circuit |
ASR: Diff brake disabled |
|
ABS Wabco D |
40B12 |
ABS error |
Short circuit between sensorwires IG/IGM is detected |
6 |
06 |
Diff. Brake Valve, shorted to ground |
ASR: Diff brake disabled |
|
ABS Wabco D |
40B13 |
ABS error |
DC voltage detected. Short circuit or impedance to battery voltage. |
3 |
03 |
Trailer Brake Valve, shorted to UBATT |
||
ABS Wabco D |
40B13 |
ABS error |
Open circuit is detected |
5 |
05 |
Trailer Brake Valve, open circuit |
||
ABS Wabco D |
40B13 |
ABS error |
Short circuit between sensorwires IG/IGM is detected |
6 |
06 |
Trailer Brake Valve, shorted to ground |
||
ABS Wabco D |
40B16 |
ABS error |
8 |
08 |
||||
ABS Wabco D |
40B17 |
ABS error |
Open circuit is detected |
5 |
05 |
Warning Light |
WL if grounded. Off if bumed out |
|
ABS Wabco D |
40BE7 |
ABS error.SAEJ1939 |
Unplausibility between received vehicle speed and ABS vehicle speed. |
2 |
02 |
SAE J1939 VSC1 speed bad plausibility |
Supevision normally not activated |
|
ABS Wabco D |
40BE7 |
ABS error.SAEJ1939 |
SAE J1939 communication impossible. SAE J1939 high open or short circuit to plus or ground or sae J1939 low or low/high are misured |
5 |
05 |
SAE J1939 open or short circuit |
ASR: disabled SMR: disabled SAE J1939 switched to inactive because communication is disturbed. |
|
ABS Wabco D |
40BE7 |
ABS error.SAEJ1939 |
SAE J1939 communication impossible. SAE J1939 high open or short circuit to plus or ground or sae J1939 low or low/high are misured |
6 |
06 |
SAE J1939 no access |
ASR: disabled SMR: disabled ABS ECU tries to restart com. Within 10s it is not possible. SAE J1939 remains inactive. FMI 5 might be additionally stored. |
|
ABS Wabco D |
40BE7 |
ABS error.SAEJ1939 |
Driveline integrated retarder sends message incorrecly. Timeout supervision detects faults if activated. |
7 |
07 |
SAE J1939 ERC_DR time-out |
Driveline retarder may cause instability. |
|
ABS Wabco D |
40BE7 |
ABS error.SAEJ1939 |
Engine integrated retarder sends message incorrecly. Timeout supervision detects faults if activated. Standard is no timeout supervision. |
8 |
08 |
SAE J1939 ERC_ER (_EXR) time-out |
Engine retarder may cause instability. |
|
ABS Wabco D |
40BE7 |
ABS error.SAEJ1939 |
Gearbox sends message incorrecly. Timeout supervision detects faults if activated. Standard is no timeout supervision. |
9 |
09 |
SAE J1939 ETC time-out |
Dragtorque control influenced. |
|
ABS Wabco D |
40BE7 |
ABS error.SAEJ1939 |
Engine control sends torque message incorrectly. Timeout supervision detects fault. |
9 |
09 |
SAE J1939 EEC1 time-out |
Dragtorque control influenced. |
|
ABS Wabco D |
40BE7 |
ABS error.SAEJ1939 |
Exaust integrated retarder sends message incorrecly. Timeout supervision detects faults if activated. Standard is no timeout supervision. |
10 |
0A |
SAE J 1939 ERC_EXR time-out |
Exaust retarder may cause instability. |
|
ABS Wabco D |
40BE7 |
ABS error.SAEJ1939 |
Internal fault |
12 |
0C |
SAE J1939, internal error |
ABS: disabled ASR: disabled SMR: disabled EBL: disabled |
|
ABS Wabco D |
40BFB |
ABS error. Overvoltage |
Supply voltage too high for more than 5s |
3 |
03 |
Overvoltage |
All valve disabled. No ABS, SMR, Diff Brake, EBL |
|
ABS Wabco D |
40BFD |
ABS error |
Wheel parameters are out of tolerance. No ABS, ASR, EBL, SM |
2 |
02 |
EEPROM, Wheel Parameter incorrect |
Wrong parameter |
|
ABS Wabco D |
40BFD |
ABS error |
Checksum of parameter or analog adjustment is wrong. |
12 |
0C |
EEPROM checksum |
No ABS, SMR, Diff Brake, EBL. No blink code. |
|
ABS Wabco D |
40BFE |
ABS error |
No modulators connected. |
5 |
05 |
Electronic w/o loads |
Normal for EOL testing of single cabin. Fault not memorized. No ABS, SMR, ASR, EBL. |
|
ABS Wabco D |
40BFE |
ABS error |
One axle was much faster than other. |
8 |
08 |
excessive slip/dynotester |
On rolling roads responce dynotester slip supervision time can be exceeded when fault detection is not disabled by diagnostic tools or blinkcode (3s). |
|
ABS Wabco D |
40BFE |
ABS error |
Control via modulator was too long. After a delay time function is normal. |
9 |
09 |
Modulator valve activation time |
75% 0f 5min modulator was activated. No ASR during fault activeness. |
|
ABS Wabco D |
40BFE |
ABS error |
Internal error |
12 |
0C |
Multiple possibilities |
Yellow |
No ABS, SMR, Diff Brake, EBL. No blink code. |
BC IBC2 |
22101 |
EEPROM checksum error |
12 |
0C |
||||
BC IBC2 |
22102 |
ECU Overheating |
The junction Temperature of the output drivers is greater than max. junction temperature(150°C). |
12 |
0C |
|||
BC IBC2 |
22103 |
Supply Line 1 |
The acquired voltage is below or above the thresholds.The error shall be |
00 |
00 |
32V<V<36V |
||
debounced. |
01 03 04 |
01 03 04 |
8V<V<18V V>36V V<8V |
|||||
BC IBC2 |
22104 |
Supply Line 2 |
The acquired voltage is below or above the thresholds.The error shall be debounced. |
00 01 03 04 |
00 01 03 04 |
32V<V<36V 8V<V<18V V>36V V<8V |
||
BC IBC2 |
22105 |
Supply Line 3 |
The acquired voltage is below or above the thresholds.The error shall be debounced. |
00 01 03 04 |
00 01 03 04 |
32V<V<36V 8V<V<18V V>36V V<8V |
||
BC IBC2 |
22106 |
Supply Line 4 |
The acquired voltage is below or above the thresholds.The error shall be |
00 |
00 |
32V<V<36V |
||
debounced. |
01 03 04 |
01 03 04 |
8V<V<18V V>36V V<8V |
|||||
BC IBC2 |
22107 |
Supply Line 5 |
The acquired voltage is below or above the thresholds.The error shall be debounced. |
00 01 03 04 |
00 01 03 04 |
32V<V<36V 8V<V<18V V>36V V<8V |
||
BC IBC2 |
22108 |
Turn Lights Right |
The acquired load current is below the threshold (at least a load on three is a open circuit) |
5 |
05 |
I< IS (Is follows the I to V linear characteristic of the lamps) |
||
BC IBC2 |
22109 |
Turn Lights Trailer Right |
On/Off diagnostic.The test is performed only when the driver is Off.The error is detected only when at open circuit. |
5 |
05 |
|||
BC IBC2 |
2210A |
Turn Lights Right or |
Driver Short Circuit to ground or Overload or Overheating protection.The |
6 |
06 |
|||
Turn Lights Trailer Right |
test is performed only when the driver is On. |
|||||||
BC IBC2 |
2210B |
Turn Lights Left |
The acquired load current is below the threshold (at least a load on three is a open circuit) |
5 |
05 |
I< IS (Is follows the I to V linear characteristic of the lamps) |
||
BC IBC2 |
2210C |
Turn Lights Trailer Left |
On/Off diagnostic.The test is performed only when the driver is Off.The error is detected only when at open circuit. |
5 |
05 |
|||
BC IBC2 |
2210D |
Turn Lights Left or Turn Lights Trailer Left |
Driver Short Circuit to ground or Overload or Overheating protection.The test is performed only when the driver is On. |
6 |
06 |
|||
BC IBC2 |
2210E |
Parking Left &Marker Right Front Lights |
The acquired load current is below the threshold (at least a load on two is a open circuit). |
5 |
05 |
I< IS (Is follows the I to V linear characteristic of the lamps) |
||
BC IBC2 |
2210F |
Parking Rear Right Lights |
The acquired load current is below the threshold (at least a load on two is a open circuit). |
5 |
05 |
I< IS (Is follows the I to V linear characteristic of the lamps) |
||
BC IBC2 |
22110 |
License Plate Lights |
The acquired load current is below the threshold (at least a load on two is a open circuit). |
5 |
05 |
I< IS (Is follows the I to V linear characteristic of the lamps) |
||
BC IBC2 |
22111 |
Parking Left & Marker Right Front Lights OR Parking Rear Right Lights OR License Plate Lights OR Trailer Lights |
Driver Short Circuit to ground or Overload or Overheating protection.The test is performed only when the driver is On. |
6 |
06 |
|||
BC IBC2 |
22112 |
Parking Right & Marker Left Front Lights |
The acquired load current is below the threshold (at least a load on two is a open circuit). |
5 |
05 |
I< IS (Is follows the I to V linear characteristic of the lamps) |
||
BC IBC2 |
22113 |
Parking Rear Left Lights |
The acquired load current is below the threshold (at least a load on two is a open circuit). |
5 |
05 |
I< IS (Is follows the I to V linear characteristic of the lamps) |
||
BC IBC2 |
22114 |
Marker Rear Lights |
The acquired load current is below the threshold (at least a load on two is |
5 |
05 |
I< IS |
||
a open circuit). |
(Is follows the I to V linear characteristic of the lamps) |
|||||||
BC IBC2 |
22115 |
Parking Right & Marker Left Front Lights OR Parking Rear Left Lights OR Marker Rear Lights OR Parking & Marker Trailer & Side Marker Left Lights |
Driver Short Circuit to ground or Overload or Overheating protection.The test is performed only when the driver is On. |
6 |
06 |
|||
BC IBC2 |
22116 |
Rear Fog Left & Right Lights |
The acquired load current is below the threshold (at least a load on two is a open circuit) |
5 |
05 |
I< IS (Is follows the I to V linear characteristic of the lamps) |
||
BC IBC2 |
22117 |
Rear Fog Left&Right Lights OR Rear Fog Trailer Left&Right Lights |
Driver Short Circuit to ground or Overload or Overheating protection.The test is performed only when the driver is On. |
6 |
06 |
|||
BC IBC2 |
22118 |
Stop Light Left |
The acquired load current is below the threshold (the only load is a open circuit). |
5 |
05 |
I< IS (Is follows the I to V linear characteristic of the lamps) |
||
BC IBC2 |
22119 |
Stop Light Right |
The acquired load current is below the threshold (the only load is a open circuit). |
5 |
05 |
I< IS (Is follows the I to V linear characteristic of the lamps) |
||
BC IBC2 |
2211A |
Stop Light Left or Stop Light Right or Stop Trailer Left&Right Lights |
Driver Short Circuit to ground or Overload or Overheating protection.The test is performed only when the driver is On. |
6 |
06 |
|||
BC IBC2 |
2211B |
Turn Lights Switches |
Turn Left and Turn Right Switchesare both activated.The Turn Left Lights Status and Turn Right Lights Status CAN parameters are ON but the Emergency Lights Status CAN parameter is OFF. |
2 |
02 |
|||
BC IBC2 |
2211C |
Windshield Wiper |
Windshield Wiper switches activated at the same time or every faulty on Windshield Wiper (fuse on supply line 6 faulty, engine blocked or short circuited, engine interrupted, cam always to ground, cam always open) |
2 |
02 |
|||
BC IBC2 |
2211D |
Engine Brake Preselection Mode Switches |
Engine Brake Mode Accelerator Idle and Engine Brake Mode Brake Pedal Switches are both activated. |
2 |
02 |
|||
BC IBC2 |
2211E |
Diff.Rear.Transv.Lock Rockwell Switches |
Diff.Rear Transv.Lock Rock.Switch2(Rear axle 1) andDiff.Rear Transv.Lock Rock.Switch1(Rear axle 1) are both activated. |
2 |
02 |
|||
BC IBC2 |
2211F |
Brake Front Air Pressure Sensor |
The acquired voltage is below or above the thresholds(see Figure 8). The error is detected only if there are no errors on the supply voltage of the sensor (Vc). (Vout/Vc)=0.08+0.04*(Bar+1) Vout ->output voltage of the sensor; Vc -> supply voltage of the sensor: Bar -> relative to atmospheric pressure |
00 01 03 04 |
00 01 03 04 |
0.6V<(Vout/Vc)<1V 0.14V<(Vout/Vc)< 0.38V Vout/Vc>1V Vout/Vc<0.14V |
||
BC IBC2 |
22120 |
Brake Rear Air Pressure Sensor |
The acquired voltage is below or above the thresholds(see Figure 8). |
00 |
00 |
0.6V<(Vout/Vc)<1V |
||
The error is detected only if there are no errors on the supply voltage of the sensor (Vc). (Vout/Vc)=0.08+0.04*(Bar+1) Vout ->output voltage of the sensor; Vc -> supply voltage of the sensor: Bar -> relative to atmospheric pressure |
01 03 04 |
01 03 04 |
0.14V<(Vout/Vc)< 0.38V Vout/Vc>1V Vout/Vc<0.14V |
ECU Name |
SPN [Hex] |
Fault Component |
Description |
FMI [DEC] |
FMI [HEX] |
FMI Description |
Lamp status |
Comment |
BC IBC2 |
2212B |
Brake Air Pressure Sensor Supply (Vc) |
The acquired supply voltage is below or above the thresholds. |
00 01 03 04 |
00 01 03 04 |
6V<V<8V 2V<V<4V V>8V V<2V |
||
BC IBC2 |
2212C |
Vehicle data bus CAN |
No CAN messages on Vehicle data bus or Bus-Off detection.The error can be read on CAN only if the CAN bus resets |
2 |
02 |
|||
BC IBC2 |
2212D |
ECU not programmed |
31 |
1F |
||||
BC IBC2 |
22130 |
Engine Starter |
03 04 |
03 04 |
Voltage Above Normal, Or Shorted To High Source Voltage Below Normal, Or Shorted To Low Source |
|||
BC IBC2 |
22131 |
Cabin Side White Lights (only if on pin E03) |
03 04 |
03 04 |
Voltage Above Normal, Or Shorted To High Source Voltage Below Normal, Or Shorted To Low Source |
|||
BC IBC3 |
22100 |
ECU not programmed |
31 |
1F |
Yellow |
|||
BC IBC3 |
22101 |
EEPROM checksum error |
12 |
0C |
Yellow |
|||
BC IBC3 |
22102 |
ECU Overheating |
The PCB ECU Temperature of the output drivers is greater than max. allowed temperature (100°C). |
13 |
0D |
Yellow |
||
BC IBC3 |
22103 |
ECU Secondary Microprocessor Faulty |
The secondary microprocessor that executes the limp-home function is faulty |
14 |
0E |
Yellow |
||
BC IBC3 |
2210B |
Vehicle Data Bus CAN |
No CAN messages on Vehicle data bus or Bus-Off detection. The error can be read on VDB CAN only if the VDB CAN bus resets |
2 |
02 |
Red |
||
BC IBC3 |
2210C |
Body Control Bus CAN |
No CAN messages on Body control bus or Bus-Off detection. The error can be read on BCB CAN also if the BCB CAN bus is not reset |
2 |
02 |
Red |
||
BC IBC3 |
231FF |
Body Control Bus — ECU#1 CAN |
No CAN messages from ECU#1 — Bed Module |
2 |
02 |
Yellow |
||
BC IBC3 |
2ECFF |
Body Control Bus — ECU#2 CAN |
No CAN messages from ECU#2 — Driver Door Module |
2 |
02 |
Yellow |
||
BC IBC3 |
2EDFF |
Body Control Bus — ECU#3 CAN |
No CAN messages from ECU#3 — Co-Driver Door Module |
2 |
02 |
Yellow |
||
BC IBC3 |
245FF |
Body Control Bus — ECU#4 CAN |
No CAN messages from ECU#4 — Additional Heater Air |
2 |
02 |
Yellow |
||
BC IBC3 |
244FF |
Body Control Bus — ECU#5 CAN |
No CAN messages from ECU#5 — Additional Heater Water |
2 |
02 |
Yellow |
||
BC IBC3 |
2E9FF |
Body Control Bus — ECU#6 CAN |
No CAN messages from ECU#6 — Mirror Controller |
2 |
02 |
Yellow |
||
BC IBC3 |
26DFF |
Body Control Bus — ECU#7 CAN |
No CAN messages from ECU#7 — MET |
2 |
02 |
Red |
||
BC IBC3 |
219FF |
Body Control Bus — ECU#8 CAN |
No CAN messages from ECU#8 — Climate Control |
2 |
02 |
Yellow |
||
BC IBC3 |
22120 |
Fuel Level Interface |
Fuel Level interface failure detected. The input voltage is evaluated for in-range checking: |
00 01 |
00 01 |
00:Delta voltage below normal 01:Delta voltage above normal |
Yellow |
|
BC IBC3 |
22121 |
Engine Oil Level Interface |
Oil Level interface failure detected. The voltage difference between the first and the second acquisition are evaluated for in-range checking: |
00 01 0F 10 12 13 14 |
00 01 15 10 12 13 14 |
00:Delta voltage below normal 01:Delta voltage above normal 0F:Time/Date from TCO not available 10:Engine Starter Mode or Engine Speed from EDC not available 12:Date could not be stored in EEPROM 13:Time could not be stored in EEPROM 14:Oil Level could not be stored in EEPROM |
Yellow |
|
BC IBC3 |
22122 |
Ambient Air Temperature Interface |
Ambient Air Temperature interface failure detected. The input voltage is evaluated for in-range checking: |
03 04 |
03 04 |
03:Voltage above normal (s.c. to battery or open circuit) 04:Voltage below normal (s.c. to ground) |
Yellow |
|
BC IBC3 |
22130 |
Windshield Wiper Switches |
Windshield Wiper switches activated at the same time or every faulty on Windshield Wiper (engine blocked or short circuited, engine interrupted, cam always to ground, cam always open) |
2 |
02 |
Yellow |
||
BC IBC3 |
22131 |
Diff.Lock.State. Rear Axle1(Rockwell) Switches |
Diff.Lock.State. Rear Axle1-In1 and Diff. Lock State Rear Axle1-In2, are both activated |
2 |
02 |
Yellow |
||
BC IBC3 |
22140 |
Service Brake Air Pressure Circuit#2 sensor (Front) |
Service Brake Air Pressure Circuit#2 interface failure detected. |
03 04 |
03 04 |
03:Voltage above normal (s.c. to battery or open circuit) 04:Voltage below normal (s.c. to ground) |
Yellow |
|
BC IBC3 |
22141 |
Service Brake Air Pressure Circuit#1 sensor (Rear) |
Service Brake Air Pressure Circuit#1 interface failure detected. |
03 05 |
03 05 |
4:Voltage above normal (s.c. to battery or open circuit) 04:Voltage below normal (s.c. to ground) |
Yellow |
|
BC IBC3 |
22142 |
Service Brake Air Pressure Circuit#2 sensor (Front) |
The pressure charging is evaluated for in-range checking |
00 01 |
00 01 |
00:Delta voltage below normal 01:Delta voltage above normal |
Red |
|
BC IBC3 |
22143 |
Service Brake Air Pressure Circuit#1 sensor (Rear) |
The pressure charging is evaluated for in-range checking |
00 01 |
00 01 |
00:Delta voltage below normal 01:Delta voltage above normal |
Red |
|
BC IBC3 |
22144 |
Service Brake Air Pressure Sensor Supply Voltage (Vs) |
Service Brake Air Pressure Sensor Supply Voltage failure detected. The error is detected only when the maximum supply voltage is between 18V and 32V and Ignition Key 15 is On. |
00 01 03 04 |
00 01 03 04 |
00: 6V<V<8V 01: 2V<V<4V 03: V>8V 04: V<2V |
Yellow |
|
BC IBC3 |
22145 |
Brake Air Dryer |
Pressure plausability: |
01 00 02 |
01 00 02 |
01:The pressure is not increasing while charge mode 00:The pressure is not decreasing while rigeneration mode 02:Duty error (air loss because the S2 valve is locked) |
Yellow |
|
BC IBC3 |
22150 |
Dashboard Backlight & Headbeam Washer Supply & Body Builders Parking Lights |
On/Off Diagnostic: |
6 |
06 |
06:Short circuit to ground or Overload or Overheating protection. |
Yellow |
|
BC IBC3 |
22161 |
Marker Front Left & Right Lights |
Analog Diagnostic: The acquired load current is below the threshold (at least a load on two is a open circuit). The error is detected only when the relative supply voltage is between 18V and 32V. The Marker Front Left & Right Lights fault shall be recognized, stored and reported on DM1 message with a maximum delay of 10sec. |
5 |
05 |
05: I < IS |
Yellow |
|
BC IBC3 |
22166 |
Additional Lights or Additional Air Heater Disable |
On/Off Diagnostic: |
03 06 |
03 06 |
03:Short circuit to battery 06:Short circuit to ground or Overload or Overheating protection |
Yellow |
|
BC IBC3 |
22163 |
Step Lights |
Analog Diagnostic: The acquired load current is below the threshold (at least a load on two is a open circuit). The error is detected only when the relative supply voltage is between 18V and 32V. The Step Lights fault shall be recognized, stored and reported on DM1 message with a maximum delay of 10sec. |
5 |
05 |
05: I < IS |
Yellow |
|
BC IBC3 |
22164 |
Cabin Side Lights |
On/Off Diagnostic: |
03 06 |
03 06 |
03:Short circuit to battery 06:Short circuit to ground or Overload or Overheating protection |
Yellow |
|
BC IBC3 |
22165 |
Cabin Ceiling Lights |
Analog Diagnostic: The acquired load current is below the threshold (at least a load on two is a open circuit). The error is detected only when the relative supply voltage is between 18V and 32V. The Cabin Ceiling Lights fault shall be recognized, stored and reported on DM1 message with a maximum delay of 10sec. |
5 |
05 |
05: I < IS |
Yellow |
|
BC IBC3 |
22180 |
30A |
On/Off Diagnostic: |
4 |
04 |
Voltage below normal |
Yellow |
|
BC IBC3 |
22181 |
30B |
On/Off Diagnostic: |
4 |
04 |
Voltage below normal |
Yellow |
|
BC IBC3 |
22182 |
30C |
On/Off Diagnostic: |
4 |
04 |
Voltage below normal |
Yellow |
|
BC IBC3 |
22183 |
30D |
On/Off Diagnostic: |
4 |
04 |
Voltage below normal |
Yellow |
|
BC IBC3 |
22184 |
30E |
On/Off Diagnostic: |
4 |
04 |
Voltage below normal |
Yellow |
|
BC IBC3 |
22190 |
+Batt. TCO & +Batt. Spare1 |
On/Off Diagnostic: The internal fuse to ECU can be accidentally interrupted |
5 |
05 |
Fuse interrupted |
Yellow |
|
BC IBC3 |
22191 |
30A Cluster |
On/Off Diagnostic: fuse interrupped The internal fuse to ECU can be accidentally interrupted |
5 |
05 |
Fuse interrupted |
Yellow |
|
BC IBC3 |
22192 |
30D Body Builders |
On/Off Diagnostic: fuse interrupped The internal fuse to ECU can be accidentally interrupted |
5 |
05 |
Fuse interrupted |
Yellow |
|
BC IBC3 |
22193 |
30E ECAS |
On/Off Diagnostic: fuse interrupped The internal fuse to ECU can be accidentally interrupted |
5 |
05 |
Fuse interrupted |
Yellow |
|
BC IBC3 |
22194 |
30C VCM |
On/Off Diagnostic: fuse interrupped The internal fuse to ECU can be accidentally interrupted |
5 |
05 |
Fuse interrupted |
Yellow |
|
BC IBC3 |
22195 |
30E Cigarette Lighter & 30E Diagnostic Connector |
On/Off Diagnostic: fuse interrupped The internal fuse to ECU can be accidentally interrupted |
5 |
05 |
Fuse interrupted |
Yellow |
|
BC IBC3 |
22196 |
30C ABS |
On/Off Diagnostic: fuse interrupped The internal fuse to ECU can be accidentally interrupted |
5 |
05 |
Fuse interrupted |
Yellow |
|
BC IBC3 |
22197 |
30C ABS Trailer |
On/Off Diagnostic: fuse interrupped The internal fuse to ECU can be accidentally interrupted |
5 |
05 |
Fuse interrupted |
Yellow |
|
BC IBC3 |
22198 |
30B Engine Crank |
On/Off Diagnostic: fuse interrupped The internal fuse to ECU can be accidentally interrupted |
5 |
05 |
Fuse interrupted |
Yellow |
|
BC IBC3 |
22199 |
30D Acustic Horn |
On/Off Diagnostic: fuse interrupped The internal fuse to ECU can be accidentally interrupted |
5 |
05 |
Fuse interrupted |
Yellow |
|
BC IBC3 |
2219A |
30E Voltage Adapter & 30E Bed Lights |
On/Off Diagnostic: fuse interrupped The internal fuse to ECU can be accidentally interrupted |
5 |
05 |
Fuse interrupted |
Yellow |
|
BC IBC3 |
2219B |
30B Mirror Heating |
On/Off Diagnostic: fuse interrupped The internal fuse to ECU can be accidentally interrupted |
5 |
05 |
Fuse interrupted |
Yellow |
|
BC IBC3 |
221A0 |
15 Mirror Controller & 15 Heated Dryer |
On/Off Diagnostic: fuse interrupped The internal fuse to ECU can be accidentally interrupted |
5 |
05 |
Fuse interrupted |
Yellow |
|
BC IBC3 |
221A1 |
15 Alternator |
On/Off Diagnostic: fuse interrupped The internal fuse to ECU can be accidentally interrupted |
5 |
05 |
Fuse interrupted |
Yellow |
|
BC IBC3 |
221A2 |
15 TCO & 15 Cluster & 15 MET & 15 UDS |
On/Off Diagnostic: fuse interrupped The internal fuse to ECU can be accidentally interrupted |
5 |
05 |
Fuse interrupted |
Yellow |
|
BC IBC3 |
221A3 |
15 VCM & 15 ECM |
On/Off Diagnostic: fuse interrupped The internal fuse to ECU can be accidentally interrupted |
5 |
05 |
Fuse interrupted |
Yellow |
|
BC IBC3 |
221A4 |
15 ECAS & 15 ABS |
On/Off Diagnostic: fuse interrupped The internal fuse to ECU can be accidentally interrupted |
5 |
05 |
Fuse interrupted |
Yellow |
|
BC IBC3 |
221A5 |
15 Cabin Tilted & 15 Brake Switch & 15 Headbeam Pot.Supply |
On/Off Diagnostic: fuse interrupped The internal fuse to ECU can be accidentally interrupted |
5 |
05 |
Fuse interrupted |
Yellow |
|
BC IBC3 |
221A6 |
15/1A Reverse Gear Lights & 15/1A Headbeam Adjustment supply & 15/1A NOX sensor supply |
On/Off Diagnostic: fuse interrupped The internal fuse to ECU can be accidentally interrupted |
5 |
05 |
Fuse interrupted |
Yellow |
|
BC IBC3 |
221A7 |
15/1A Cabin Heater & 15/1A Conditioner |
On/Off Diagnostic: fuse interrupped The internal fuse to ECU can be accidentally interrupted |
5 |
05 |
Fuse interrupted |
Yellow |
|
BC IBC3 |
221A8 |
15/1B Body Builders |
On/Off Diagnostic: fuse interrupped The internal fuse to ECU can be accidentally interrupted |
5 |
05 |
Fuse interrupted |
Yellow |
|
BC IBC3 |
221A9 |
15/1B Electric Windows |
On/Off Diagnostic: fuse interrupped The internal fuse to ECU can be accidentally interrupted |
5 |
05 |
Fuse interrupted |
Yellow |
|
BC IBC3 |
221B0 |
Power Steering Circuit #1 or #2 Pressure Low |
Sensor plausibility: — While Engine Speed=0 (and valid) at least one of two pressure switches is in Normal state (open) (pressure above threshold) The ECU waits PSC_TEST_T1 (after Engine Speed =0 or at Ignition Key 15) before to start the diagnostics |
2 |
02 |
Flow meter plausibility |
Yellow |
|
BC IBC3 |
221B2 |
Steering Flow Meter |
Flow meter plausibility: — When Vehicle Speed < PSC_VEH_SPEED _MIN the flow is in Normal state (open) |
2 |
02 |
Flow meter plausibility |
Yellow |
|
BC IBC3 |
221C0 |
Windshield Washer & Headbeam Washer |
On/Off Diagnostic: |
03 06 |
03 06 |
03:Short circuit to battery 06:Short circuit to ground or Overload or Overheating protection |
Yellow |
|
BC IBC3 |
221C1 |
TGC ON |
On/Off Diagnostic: |
03 |
03 |
03:Short circuit to battery |
Yellow |
|
06 |
06 |
06:Short circuit to ground or Overload or Overheating protection |
||||||
BC IBC3 |
221C2 |
TGC OFF |
On/Off Diagnostic: |
3 |
03 |
03:Short circuit to battery |
Yellow |
|
BC IBC3 |
221C3 |
Body Builder Reverse Gear |
On/Off Diagnostic: |
03 06 |
03 06 |
03:Short circuit to battery 06:Short circuit to ground or Overload or Overheating protection |
Yellow |
ECU Name |
SPN [Hex] |
Fault Component |
Description |
FMI [DEC] |
FMI [HEX] |
FMI Description |
Lamp status |
Comment |
BC IBC3 |
221C4 |
Vehicle Running |
On/Off Diagnostic: |
03 06 |
03 06 |
03:Short circuit to battery 06:Short circuit to ground or Overload or Overheating protection |
Yellow |
|
BC IBC3 |
221C5 |
Engine Running |
On/Off Diagnostic: |
03 06 |
03 06 |
03:Short circuit to battery 06:Short circuit to ground or Overload or Overheating protection |
Yellow |
|
BC IBC3 |
221C6 |
Roof Hatch opening |
On/Off Diagnostic: |
03 06 |
03 06 |
03:Short circuit to battery 06:Short circuit to ground or Overload or Overheating protection |
Yellow |
|
BC IBC3 |
221C7 |
Roof Hatch closing |
On/Off Diagnostic: |
03 07 |
03 07 |
4:Short circuit to battery 06:Short circuit to ground or Overload or Overheating protection |
Yellow |
|
BC IBC3 |
221C8 |
Headlights Washer |
On/Off Diagnostic: |
03 08 |
03 08 |
5:Short circuit to battery 06:Short circuit to ground or Overload or Overheating protection |
Yellow |
|
BC MET |
26D01 |
EEPROM checksum error |
12 |
0C |
Yellow |
|||
BC MET |
26D02 |
ECU Overheating |
The PCB ECU Temperature of the output drivers is greater than max. allowed temperature (100°C). |
12 |
0C |
Yellow |
||
BC MET |
26D03 |
ECU Secondary Microprocessor Faulty |
The secondary microprocessor that executes the limp-home function is faulty |
12 |
0C |
Yellow |
||
BC MET |
26D0C |
Body Control bus CAN |
No CAN messages on Body Control bus or Bus-Off detection. The error can be read on BCB CAN only if the BCB CAN bus resets |
2 |
02 |
Red |
||
BC MET |
26D20 |
Fuel Level sensor |
Fuel Level interface failure detected. The input voltage is evaluated for Phisically possible range: |
03 04 |
03 04 |
03:Voltage above normal (s.c. to battery) 04:Voltage below normal (s.c. to ground). Only when the current is sensed on the Low Side |
Yellow |
|
BC MET |
26D21 |
Engine Oil Level Sensor |
Oil level interface failure detected. The input voltage is evaluated for Phisically possible range: |
03 04 |
03 04 |
03:Voltage above normal (s.c. to battery) 04:Voltage below normal (s.c. to ground ) |
Yellow |
|
BC MET |
26D51 |
Parking Left & Right Front Lights & Parking Rear Left Lights & Marker Rear Left & Right Lights & Trailer Parking Lights Left |
Analog Diagnostic: The error is detected only when the relative supply voltage is between 18V and 32V. |
6 |
06 |
06:short circuit to ground or Overload or Overheating protection |
Yellow |
|
BC MET |
26D52 |
Parking Left & Right Front Lights |
Analog Diagnostic: The acquired load current is below the threshold. The error is detected only when the relative supply voltage is between 18V and 32V. |
5 |
05 |
05: I < IS |
Yellow |
|
BC MET |
26D53 |
Parking Rear Left Lights |
Analog Diagnostic: The acquired load current is below the threshold. The error is detected only when the relative supply voltage is between 18V and 32V. |
5 |
05 |
05: I < IS |
Yellow |
|
BC MET |
26D54 |
Parking Rear Right Lights |
Analog Diagnostic: The acquired load current is below the threshold. The error is detected only when the relative supply voltage is between 18V and 32V. |
5 |
05 |
05: I < IS |
Yellow |
|
BC MET |
26D55 |
Parking Rear Right Lights & Plate Left & |
Analog Diagnostic: The error is detected only when the relative supply voltage is between 18V |
6 |
06 |
06:short circuit to ground or Overload or Overheating protection |
Yellow |
|
Right Lights & Trailer Parking Lights Right |
and 32V. |
|||||||
BC MET |
26D56 |
Rear Fog Left & Right Lights |
Analog Diagnostic: The acquired load current is below the threshold. The error is detected only when the relative supply voltage is between 18V and 32V. |
5 |
05 |
05: I < IS |
Yellow |
|
BC MET |
26D57 |
Rear Fog Left & Right Lights & Trailer Rear Fog Left & Right Lights |
Analog Diagnostic: The error is detected only when the relative supply voltage is between 18V and 32V. |
5 |
05 |
06:short circuit to ground or Overload or Overheating protection |
Yellow |
|
BC MET |
26D58 |
Stop Light Left |
Analog Diagnostic: The acquired load current is below the threshold. The error is detected only when the relative supply voltage is between 18V and 32V. |
5 |
05 |
05: I < IS |
Yellow |
|
BC MET |
26D59 |
Stop Light Right |
Analog Diagnostic: The acquired load current is below the threshold. The error is detected only when the relative supply voltage is between 18V and 32V. |
5 |
05 |
05: I < IS |
Yellow |
|
BC MET |
26D5A |
Stop Light Left & Stop Light Right & Trailer Stop Left & Right Lights |
Analog Diagnostic: The error is detected only when the relative supply voltage is between 18V and 32V. |
6 |
06 |
06:short circuit to ground or Overload or Overheating protection |
Yellow |
|
BC MET |
26D5B |
Front Fog Left & Right Lights |
On/Off Diagnostic: The error is detected only when the relative supply voltage is between 18V and 32V. |
6 |
06 |
06:short circuit to ground or Overload or Overheating protection |
Yellow |
|
BC MET |
26D5C |
Low Beam Light Left |
On/Off Diagnostic: |
05 06 |
05 06 |
05:Open load 06:Short circuit to ground or Overload or Overheating protection |
Yellow |
|
BC MET |
26D5D |
Low Beam Light Right |
On/Off Diagnostic: |
05 06 |
05 06 |
05:Open load 06:Short circuit to ground or Overload or Overheating protection |
Yellow |
|
BC MET |
26D5E |
High Beam Light Left |
On/Off Diagnostic: |
05 06 |
05 06 |
05:Open load 06:Short circuit to ground or Overload or Overheating protection |
Yellow |
|
BC MET |
26D5F |
High Beam Light Right |
On/Off Diagnostic: |
05 06 |
05 06 |
05:Open load 06:Short circuit to ground or Overload or Overheating protection |
Yellow |
|
BC MET |
26D60 |
Plate Left & Right Lights |
Analog Diagnostic: The acquired load current is below the threshold. The error is detected only when the relative supply voltage is between 18V and 32V. |
5 |
05 |
05: I < IS |
Yellow |
|
BC MET |
26D62 |
Marker Rear Left & Right Lights |
Analog Diagnostic: The acquired load current is below the threshold. The error is detected only when the relative supply voltage is between 18V and 32V. |
5 |
05 |
05: I < IS |
Yellow |
|
BC MET |
26D68 |
Turn Right Lights |
Analog Diagnostic: The acquired load current is below the threshold. The error is detected only when the relative supply voltage is between 18V and 32V. |
5 |
05 |
05: I < IS |
Yellow |
|
BC MET |
26D69 |
Trailer Turn Lights Right |
On/Off Diagnostic: The error is detected only when all the lamps are open circuit and the relative supply voltage is between 18V and 32V. |
5 |
05 |
05: I < IS |
Yellow |
|
BC MET |
26D6A |
Turn & Trailer Turn Right Lights |
On/Off Diagnostic: The error is detected only when the relative supply voltage is between 18V and 32V. |
5 |
05 |
06: Short circuit to ground or Overload or Overheating protection |
Yellow |
|
BC MET |
26D6B |
Turn Left Lights |
Analog Diagnostic: The acquired load current is below the threshold. The error is detected only when the relative supply voltage is between 18V and 32V. |
5 |
05 |
05: I < IS |
Yellow |
|
BC MET |
26D6C |
Trailer Turn Lights Left |
On/Off Diagnostic: The error is detected only when all the lamps are open circuit and the relative supply voltage is between 18V and 32V. |
5 |
05 |
5: I< IS Is =40mA |
Yellow |
|
BC MET |
26D6D |
Turn & Trailer Turn Left Lights |
On/Off Diagnostic: The error is detected only when the relative supply voltage is between 18V and 32V. |
6 |
06 |
06: Short circuit to ground or Overload or Overheating protection |
Yellow |
|
BC MET |
26D6E |
Trailer Stop Left & Right Lights |
Analog Diagnostic: The acquired load current is below the threshold (see Figura 2). |
5 |
05 |
5: I< IS |
Yellow |
|
The error is detected only when the relative supply voltage is between 18V and 32V. |
Is =40mA |
|||||||
BC MET |
26DA1 |
Ignition Key 15 Body Builder &Trailer |
On/Off Diagnostic: |
5 |
05 |
06: Short circuit to ground or Overload or Overheating protection |
Yellow |
|
BC MET |
26DC0 |
A-A8+P-A1 output |
On/Off Diagnostic: |
5 |
05 |
06: Short circuit to ground or Overload or Overheating protection |
Yellow |
|
BC MET |
26DC1 |
A-B1 output |
On/Off Diagnostic: |
5 |
05 |
06: Short circuit to ground or Overload or Overheating protection |
Yellow |
|
BC MET |
26DC3 |
Headbeam Adjustment |
On/Off Diagnostic: |
03 06 |
03 06 |
03:Short circuit to battery 06:Short circuit to ground (with Hheadbeam Adjustment Position > 4%) |
Yellow |
|
BC MET |
26DC5 |
A-C1 output |
On/Off Diagnostic: |
5 |
05 |
06:short circuit to ground or Overload or Overheating protection |
Yellow |
|
BC MET |
26DC8 |
C-A1 output |
On/Off Diagnostic: |
05 06 03 |
05 06 03 |
05: Open load 06: Short circuit to ground or Overload or Overheating protection 03: Short circuit to battery |
Yellow |
|
BC MET |
26DC9 |
C-A2 output |
On/Off Diagnostic: |
05 06 03 |
05 06 03 |
05: Open load 06: Short circuit to ground or Overload or Overheating protection 03: Short circuit to battery |
Yellow |
|
BC MET |
26DCA |
C-A3 output |
On/Off Diagnostic: |
05 06 03 |
05 06 03 |
05: Open load 06: Short circuit to ground or Overload or Overheating protection 03: Short circuit to battery |
Yellow |
|
BC MET |
26DCD |
C-A4 output |
On/Off Diagnostic: |
05 06 03 |
05 06 03 |
05: Open load 06: Short circuit to ground or Overload or Overheating protection 03: Short circuit to battery |
Yellow |
|
BC MET |
26DCE |
C-A5 output |
On/Off Diagnostic: |
05 06 03 |
05 06 03 |
05: Open load 06: Short circuit to ground or Overload or Overheating protection 03: Short circuit to battery |
Yellow |
|
CLC |
41905 |
Solar Sensor |
04 05 |
04 05 |
04: Short circuit to ground 05: Open load or short cricuit to battery |
Yellow |
||
CLC |
41906 |
Indoor temperature sensor |
04 |
04 |
04: Short circuit to ground |
Yellow |
||
05 |
05 |
05: Open load or short cricuit to battery |
||||||
CLC |
41907 |
Evaporator temperature sensor |
04 05 |
04 05 |
04: Short circuit to ground 05: Open load or short cricuit to battery |
Yellow |
||
CLC |
41908 |
Heater exchanger temperature sensor |
04 05 |
04 05 |
04: Short circuit to ground 05: Open load or short cricuit to battery |
Yellow |
||
CLC |
41901 |
Feedback signal floor flap |
04 05 |
04 05 |
04: Short circuit to ground 05: Open load or short cricuit to battery |
Yellow |
||
CLC |
41902 |
Feedback signal defrost flap |
04 05 |
04 05 |
04: Short circuit to ground 05: Open load or short cricuit to battery |
Yellow |
||
CLC |
41903 |
Feedback signal bilevel flap |
04 05 |
04 05 |
04: Short circuit to ground 05: Open load or short cricuit to battery |
Yellow |
||
CLC |
41904 |
Feedback signal recirculation flap |
04 |
04 |
04: Short circuit to ground |
Yellow |
||
05 |
05 |
05: Open load or short circuit to battery |
||||||
CLC |
41914 |
Sensor fan diagnosis |
07 |
07 |
Faulty feedback from fan motor |
Yellow |
||
CLC |
4190E |
Heating valve |
04 03 07 |
04 03 07 |
04: Short cricuit to ground 03: Short circuit to battery 07: Flap is not moving |
Yellow |
||
CLC |
41910 |
Floor flap motor |
04 03 07 |
04 03 07 |
04: Short cricuit to ground 03: Short circuit to battery 07: Flap is not moving |
Yellow |
ECU Name |
SPN [Hex] |
Fault Component |
Description |
FMI [DEC] |
FMI [HEX] |
FMI Description |
Lamp status |
Comment |
|
EDC7C1 |
20052 |
Lowside Powerstage 6 |
|||||||
EDC7C1 |
20053 |
Small Signal Powerstage 1 |
|||||||
EDC7C1 |
20054 |
Small Signal Powerstage 2 |
|||||||
EDC7C1 |
20055 |
Small Signal Powerstage 3 |
|||||||
EDC7C1 |
20056 |
Small Signal Powerstage 4 |
|||||||
EDC7C1 |
20057 |
Solenoid Powerstage 1 |
|||||||
EDC7C1 |
20058 |
Solenoid Powerstage 2 |
|||||||
EDC7C1 |
20059 |
Solenoid Powerstage 3 |
|||||||
EDC7C1 |
2005A |
Solenoid Powerstage 4 |
|||||||
EDC7C1 |
2005B |
Solenoid Powerstage 5 |
|||||||
EDC7C1 |
2005C |
Solenoid Powerstage 6 |
|||||||
EDC7UC31 |
10011 |
Vehicle Speed failure |
VSSCD1 |
02 03 04 12 |
02 03 04 0C |
Signal not valid Value above Limit Distance factor not learned Signal not plausible |
Yellow |
||
EDC7UC31 |
10012 |
Accelerator Pedal 1 failure |
APP1 |
03 04 12 |
03 04 0C |
Signal too high Signal too low Signal not plausible to the reference signal |
Yellow |
||
EDC7UC31 |
10014 |
Multiple State Switch failure |
MSSCD |
03 04 12 |
03 04 0C |
Short to Battery Short to Ground Signal not plausible |
Yellow |
||
EDC7UC31 |
10016 |
Main Clutch Signal failure |
ConvCD |
02 12 |
02 0C |
Info: Clutch signal failure via CAN Signal not plausible |
|||
EDC7UC31 |
10017 |
Brake Signal failure |
BrkCD |
02 12 |
02 0C |
Signal failure Signal not plausible |
Yellow |
||
EDC7UC31 |
10019 |
Terminal 15 failure |
T15CD |
2 |
02 |
No Signal |
|||
EDC7UC31 |
1001F |
SCR Temperatures plausibility |
SCRCatPlausIv |
02 03 04 12 |
02 03 04 0C |
02: Ambient Temperature of Humidity Sensor or both Catalyst Temperatures not plausible 03: Temperature after Catalyst not plausible 04: Temperature before Catalyst not plausible 0C: Temperature Deviation between up- and downstream Catalyst Temperature too high during Operation |
MIL |
Power Reduction (OBD) Long Term Failure |
|
EDC7UC31 |
10025 |
Main Relay 2 failure (Grid Heater 1, Fan 1, |
MRlyCD |
03 |
03 |
Short to Battery |
|||
VGT, Lambda Heater, EGR Bypass Valve, EGR Actuator, Blow By Valve) |
04 |
04 |
Short to Ground |
||||||
EDC7UC31 |
10026 |
Battery Voltage failure |
BattCD |
03 04 |
03 04 |
Signal too high Signal too low |
Yellow |
||
EDC7UC31 |
10027 |
Engine Brake decompression Valve failure |
CRERCD |
02 03 04 |
02 03 04 |
Open Load Short to Battery Short to Ground |
Red |
Long Term Failure Lamp status = Yellow on E5, Red ob EE E3 |
|
EDC7UC31 |
10028 |
Main Relay 1 (Engine Brake Decompression Valve) Short to Battery |
MnRly1_SCB |
3 |
03 |
Short to Battery |
Yellow |
Long Term Failure |
|
EDC7UC31 |
10029 |
Main Relay 3 failure (A/C Compressor, Fuel Filter Heater, Intercooler Bypass Valve, Additive Valve, Grid Heater 2, Fan 2, OBD/Cold Start/ Adjustable Speed Limiter Lamp) |
MRlyCDMnRly3 |
03 04 |
03 04 |
Short to Battery Short to Ground |
|||
EDC7UC31 |
1002B |
Air Heater 1 Power Stage failure |
ArHt1 |
02 03 04 |
02 03 04 |
Open Load Short to Battery Short to Ground |
Yellow |
||
EDC7UC31 |
1002E |
Air Heater always on |
AirHtStickOnIv |
3 |
03 |
Multi Signal failure |
Yellow |
||
EDC7UC31 |
10031 |
Coolant Temperature Sensor failure |
CTSCD |
02 03 04 12 |
02 03 04 0C |
CAN Signal failure Signal too high Signal too low Signal not plausible to Oil Temperature |
Yellow |
||
EDC7UC31 |
10032 |
Coolant Temperature Dynamic failure |
Clg_DynTst |
12 |
0C |
Minimum Temperature Rise not reached |
|||
EDC7UC31 |
10033 |
Boost Air Temperature Sensor failure |
IATSCD |
02 |
02 |
CAN Signal failure |
Long Term Failure |
||
03 04 |
03 04 |
Signal too high Signal too low |
|||||||
EDC7UC31 |
10034 |
Boost Pressure Sensor failure |
BPSCD |
02 03 04 12 |
02 03 04 0C |
CAN Signal failure Signal too high Signal too low Signal not plausible |
Yellow |
Power Reduction (Technical) Long Term Failure |
|
EDC7UC31 |
10035 |
Fuel Temperature Sensor failure |
FTSCD |
03 04 |
03 04 |
Signal too high Signal too low |
Yellow |
Long Term Failure |
|
EDC7UC31 |
10038 |
Oil Pressure Sensor failure |
OPSCD |
02 03 04 12 |
02 03 04 0C |
Hardware failure Signal too high Signal too low Value too high |
Yellow |
||
EDC7UC31 |
1003A |
Oil Temperature Sensor failure |
OTSCD |
02 03 04 12 |
02 03 04 0C |
CAN Signal failure Signal too high Signal too low Signal not plausible with Coolant Temperature |
Yellow |
||
EDC7UC31 |
1003C |
Ambient Air Temperature Sensor failure (of Humidity Sensor) |
EATSCD |
02 03 04 |
02 03 04 |
CAN Signal failure Signal too high Signal too low |
Long Term Failure |
||
EDC7UC31 |
10041 |
Crankshaft Speed Signal failure |
EngMCrS1 |
02 04 |
02 04 |
No Signal Signal wrong |
Yellow + MIL |
Power Reduction (Technical) Long Term Failure |
|
EDC7UC31 |
10042 |
Engine runs with Camshaft Speed only |
EngMBackUp |
3 |
03 |
Backup Mode |
Yellow |
Power Reduction (Technical) |
|
EDC7UC31 |
10043 |
Camshaft Speed Signal failure |
EngMCaS1 |
02 04 |
02 04 |
No Signal Signal wrong |
Yellow |
Power Reduction (Technical) |
|
EDC7UC31 |
10044 |
Offset between Camshaft and Crankshaft |
EngMOfsCaSCrS |
3 |
03 |
Offset between Signals |
Yellow + |
Long Term Failure |
|
MIL |
|||||||||
EDC7UC31 |
10045 |
Fan Actuator 1 failure |
FanCD |
02 03 04 12 |
02 03 04 0C |
Open Load Short to Battery Short to Ground Temperature too high |
Yellow |
||
EDC7UC31 |
10046 |
Fan Actuator 2 Power Stage failure |
FanCD2 |
02 03 04 |
02 03 04 |
Open Load Short to Battery Short to Ground |
Yellow |
||
EDC7UC31 |
1004D |
Info: Engine Overspeed Protection |
EngPrtOvrSpd |
3 |
03 |
Engine Overspeed |
|||
EDC7UC31 |
1004F |
Info: OBD Performance Limiter Intervention by Legislation |
CoVehPrflmAct |
3 |
03 |
Performance Limitation active |
Yellow |
||
EDC7UC31 |
10051 |
Cylinder 1 BIP search failure |
BIPCyl1 |
3 |
03 |
Too many unsuccessful searches |
Yellow + |
Power Reduction (Technical) |
|
MIL |
Long Term Failure |
||||||||
EDC7UC31 |
10052 |
Cylinder 2 BIP search failure |
BIPCyl2 |
3 |
03 |
Too many unsuccessful searches |
Yellow + MIL |
Power Reduction (Technical) Long Term Failure |
|
EDC7UC31 |
10053 |
Cylinder 3 BIP search failure |
BIPCyl3 |
3 |
03 |
Too many unsuccessful searches |
Yellow + MIL |
Power Reduction (Technical) Long Term Failure |
|
EDC7UC31 |
10054 |
Cylinder 4 BIP search failure |
BIPCyl4 |
3 |
03 |
Too many unsuccessful searches |
Yellow + MIL |
Power Reduction (Technical) Long Term Failure |
|
EDC7UC31 |
10055 |
Cylinder 5 BIP search failure |
BIPCyl5 |
3 |
03 |
Too many unsuccessful searches |
Yellow + MIL |
Power Reduction (Technical) Long Term Failure |
|
EDC7UC31 |
10056 |
Cylinder 6 BIP search failure |
BIPCyl6 |
3 |
03 |
Too many unsuccessful searches |
Yellow + MIL |
Power Reduction (Technical) Long Term Failure |
|
EDC7UC31 |
1005F |
Info: Long Term Fuel system Failure |
OBDGFClct1 |
3 |
03 |
Long Term Fault present |
MIL |
Long Term Failure ( (not deletable until after 400 days) |
|
EDC7UC31 |
10061 |
Injector Cylinder 1 failure |
InjVlvCyl1A |
02 03 04 12 |
02 03 04 0C |
Short High Side to Ground Short Low Side to Battery Depending on Application Not classifiable failure |
Yellow + MIL |
Long Term Failure |
|
EDC7UC31 |
10062 |
Injector Cylinder 2 failure |
InjVlvCyl2A |
02 03 04 12 |
02 03 04 0C |
Short High Side to Ground Short Low Side to Battery Depending on Application Not classifiable failure |
Yellow + MIL |
Long Term Failure |
|
EDC7UC31 |
10063 |
Injector Cylinder 3 failure |
InjVlvCyl3A |
02 03 04 |
02 03 04 |
Short High Side to Ground Short Low Side to Battery Depending on Application |
Yellow + MIL |
Long Term Failure |
|
12 |
0C |
Not classifiable failure |
|||||||
EDC7UC31 |
10064 |
Injector Cylinder 4 failure |
InjVlvCyl4A |
02 03 04 12 |
02 03 04 0C |
Short High Side to Ground Short Low Side to Battery Depending on Application Not classifiable failure |
Yellow + MIL |
Long Term Failure |
|
EDC7UC31 |
10065 |
Injector Cylinder 5 failure |
InjVlvCyl5A |
02 03 04 12 |
02 03 04 0C |
Short High Side to Ground Short Low Side to Battery Depending on Application Not classifiable failure |
Yellow + MIL |
Long Term Failure |
|
EDC7UC31 |
10066 |
Injector Cylinder 6 failure |
InjVlvCyl6A |
02 03 04 |
02 03 04 |
Short High Side to Ground Short Low Side to Battery Depending on Application |
Yellow + MIL |
Long Term Failure |
|
12 |
0C |
Not classifiable failure |
|||||||
EDC7UC31 |
10067 |
Injector Cylinder 1 warning |
InjVlvCyl1B |
02 03 04 12 |
02 03 04 0C |
Open Load Fast Decay Error Depending on Application Current Level Error |
Yellow + MIL |
Long Term Failure |
|
EDC7UC31 |
10068 |
Injector Cylinder 2 warning |
InjVlvCyl2B |
02 03 04 12 |
02 03 04 0C |
Open Load Fast Decay Error Depending on Application Current Level Error |
Yellow + MIL |
Long Term Failure |
|
EDC7UC31 |
10069 |
Injector Cylinder 3 warning |
InjVlvCyl3B |
02 03 04 |
02 03 04 |
Open Load Fast Decay Error Depending on Application |
Yellow + MIL |
Long Term Failure |
|
12 |
0C |
Current Level Error |
|||||||
EDC7UC31 |
1006A |
Injector Cylinder 4 warning |
InjVlvCyl4B |
02 03 04 12 |
02 03 04 0C |
Open Load Fast Decay Error Depending on Application Current Level Error |
Yellow + MIL |
Long Term Failure |
|
EDC7UC31 |
1006B |
Injector Cylinder 5 warning |
InjVlvCyl5B |
02 03 04 12 |
02 03 04 0C |
Open Load Fast Decay Error Depending on Application Current Level Error |
Yellow + MIL |
Long Term Failure |
|
EDC7UC31 |
1006C |
Injector Cylinder 6 warning |
InjVlvCyl6B |
02 03 04 |
02 03 04 |
Open Load Fast Decay Error Depending on Application |
Yellow + MIL |
Long Term Failure |
|
12 |
0C |
Current Level Error |
|||||||
EDC7UC31 |
1006E |
Minimum Injections Number not reached |
InjVlvNumMinInj |
3 |
03 |
Number of Injections not reached |
Red |
||
EDC7UC31 |
10071 |
Injector Bank 1 failure |
InjVlvBnk1A |
02 03 04 12 |
02 03 04 0C |
Depending on Application Short circuit Short Low Side to Ground Not classifiable failure |
Yellow + MIL |
Long Term Failure |
ECU Name |
SPN [Hex] |
Fault Component |
Description |
FMI [DEC] |
FMI [HEX] |
FMI Description |
Lamp status |
Comment |
|
EDC7UC31 |
10073 |
Injector Bank 2 failure |
InjVlvBnk2A |
02 03 04 12 |
02 03 04 0C |
Depending on Application Short circuit Short Low Side to Ground Not classifiable failure |
Yellow + MIL |
Long Term Failure |
|
EDC7UC31 |
1007C |
ECU Hardware for Injection: CY33X Chip specific failure (1) |
InjVlvChipA |
02 03 04 12 |
02 03 04 0C |
Test Mode Internal reset — Clock Loss — Voltage too low Unlocked — Init fail SPI Communication failure |
Yellow |
||
EDC7UC31 |
1007F |
Failure in Injection Quantity Adjustment |
InjVlvQntAdj |
02 |
02 |
EEPROM Adjustment Value not readable |
Yellow |
||
(NIMA Programming) |
12 |
0C |
Invalid EEPROM Adjustment Value Checksum |
||||||
EDC7UC31 |
10081 |
Differential Pressure Sensor Failure between Exhaust and Intake (EGR Valve) |
IEDPCDPDiff |
03 04 |
03 04 |
Signal too high Signal too low |
Yellow + MIL |
||
EDC7UC31 |
10091 |
Boost Pressure Actuator Current failure |
BPACD_ADC |
02 03 04 |
02 03 04 |
Signal not plausible Signal too high Signal too low |
Yellow |
||
EDC7UC31 |
10092 |
Boost Pressure Actuator Short to Battery |
BPACD_Max |
3 |
03 |
Short to Battery |
Yellow |
Long Term Failure |
|
EDC7UC31 |
10093 |
Turbine Speed Sensor failure |
TSSCD |
02 03 04 12 |
02 03 04 0C |
Signal not valid Signal too high Signal too low Signal not plausible |
Yellow |
||
EDC7UC31 |
10098 |
Turbocharger Control failure |
PCRMulSigDfctIv |
3 |
03 |
Multi Signal failure |
Yellow |
||
EDC7UC31 |
10099 |
Turbocharger Control Overboost Pressure failure |
PCRP2Iv |
02 03 |
02 03 |
Pressure deviation too high Pressure too high |
Yellow |
Power Reduction (Technical) Long Term Failure |
|
EDC7UC31 |
1009A |
Turbocharger Control Turbo Speed failure |
PCRTrbIv |
02 03 |
02 03 |
Irreversible Overspeed Reversible Overspeed |
Yellow |
Power Reduction (Technical) |
|
EDC7UC31 |
1009B |
Turbine Overspeed at Normal Atmospheric Pressure |
TrbChIv |
3 |
03 |
Irreversible turbine overspeed |
Yellow |
||
EDC7UC31 |
1009E |
Torque Reduction due to Smoke Limitation |
SmkTrqLim |
4 |
04 |
Torque Limitation |
|||
EDC7UC31 |
1009F |
NOx Estimation failure |
NOxEstIv |
3 |
03 |
Estimated Nox signal not reliable |
|||
EDC7UC31 |
100A2 |
NOx Sensor Plausiblity failure |
FrmMngNOxSensNOxIv |
12 |
0C |
Signal not plausible |
MIL |
Power Reduction (OBD) Long Term Failure |
|
EDC7UC31 |
100A3 |
NOx Sensor Failure |
FrmMngNOxSensIv |
03 |
03 |
Open Load |
MIL |
Power Reduction (OBD) |
|
04 12 |
04 0C |
Short Circuit Sensor not ready in time |
Long Term Failure |
||||||
EDC7UC31 |
100A4 |
CAN Message timeout Nox (from Nox Sensor) |
FrmMngTONOxSensIv |
02 04 |
02 04 |
No Signal Signal wrong |
MIL |
Power Reduction (OBD) Long Term Failure |
|
EDC7UC31 |
100A5 |
CAN Message timeout DM1DCU (from DCU) |
FrmMngTODM1DCUIv |
02 04 |
02 04 |
No Signal Signal wrong |
Yellow + MIL |
Power Reduction (OBD) Long Term Failure |
|
EDC7UC31 |
100A6 |
CAN Message timeout SCR1 (from DCU) |
FrmMngTOSCR1Iv |
02 04 |
02 04 |
No Signal Signal wrong |
Yellow + MIL |
Power Reduction (OBD) Long Term Failure |
|
EDC7UC31 |
100A8 |
Info: SCR Dosing Valve Overheat Protection |
FrmMngSCR1ProtIv |
03 04 |
03 04 |
Torque Limitation Level2 for SCR Protection active Torque Limitation Level1 for SCR Protection active |
Yellow |
||
EDC7UC31 |
100AE |
Humidity Sensor Signal Ratio failure |
IAHSCDStrtDly |
03 04 |
03 04 |
Signal Ratio above Limit Signal Ratio below Limit |
Long Term Failure |
||
EDC7UC31 |
100AF |
Info: DCU Error1 via CAN message DM1DCU |
FrmMngDM1SPN1Iv |
3 |
03 |
Error in DCU active |
Power Reduction (OBD) |
||
EDC7UC31 |
100B1 |
CAN A Bus off |
NetMngCANAOff |
3 |
03 |
CAN Bus off |
|||
EDC7UC31 |
100B2 |
CAN B Bus off |
NetMngCANBOff |
3 |
03 |
CAN Bus off |
|||
EDC7UC31 |
100B3 |
CAN C Bus off |
NetMngCANCOff |
3 |
03 |
CAN Bus off |
|||
EDC7UC31 |
100B4 |
CAN Message timeout BC2EDC1 (from Body Computer) |
FrmMngTOBC2EDC1Iv |
02 04 |
02 04 |
No Signal Signal wrong |
Yellow |
||
EDC7UC31 |
100B5 |
CAN Message timeout VM2EDC (from VCM) |
FrmMngTOVM2EDCIv |
02 04 |
02 04 |
No Signal Signal wrong |
Yellow |
||
EDC7UC31 |
100B7 |
CAN Transmit Message timeout |
FrmMngTxTO |
2 |
02 |
CAN timeout |
Yellow |
Power Reduction (OBD) |
|
EDC7UC31 |
100B9 |
Info: MIL visualization not available |
FrmMngBC1MILIv |
3 |
03 |
MIL visualization not available |
Yellow + MIL |
||
EDC7UC31 |
100BA |
CAN Message timeout Dash Display (from VCM) |
FrmMngTODashDsplIv |
02 04 |
02 04 |
No Signal Signal wrong |
|||
EDC7UC31 |
100BC |
CAN Message timeout AMCON (from VCM) |
FrmMngTORxAMCONIv |
02 04 |
02 04 |
No Signal Signal wrong |
|||
EDC7UC31 |
100BD |
CAN Message timeout CCVS (from Body Computer or VCM) |
FrmMngTORxCCVS |
2 |
02 |
CAN timeout |
|||
EDC7UC31 |
100C2 |
CAN Message timeout ETC1 (from Electronic Transmission Controller) |
FrmMngTOETC1 |
2 |
02 |
CAN timeout |
Yellow |
||
EDC7UC31 |
100C3 |
CAN Message timeout TCO1 (from Tachograph Output) |
FrmMngTOTCO1 |
2 |
02 |
CAN timeout |
|||
EDC7UC31 |
100C6 |
CAN Message timeout active TSC1-PE (Torque/Speed Control Request from PTO to Engine) |
FrmMngTOTSC1PEActIv |
3 |
03 |
CAN timeout |
Yellow |
||
EDC7UC31 |
100C8 |
CAN Message timeout active TSC1-VE (Torque/Speed Control Request from VCM/BC to Engine) |
FrmMngTOTSC1VEActIv |
3 |
03 |
CAN timeout |
Yellow |
||
EDC7UC31 |
100D1 |
ECU Hardware: SPI Communication failure |
HWEMonCom |
3 |
03 |
CJ940 Communication failure |
Red |
||
EDC7UC31 |
100D2 |
ECU Hardware: EEPROM failure |
HWEMonEEPROM |
02 04 12 |
02 04 0C |
Write failure Read failure Default Value used |
|||
EDC7UC31 |
100D3 |
ECU recovery — locked |
HWEMonRcyLocked |
12 |
0C |
Recovery occurred |
Red |
||
EDC7UC31 |
100D4 |
ECU Hardware: Microcontroller Watchdog fail |
Montr |
12 |
0C |
Watchdog and Controller not plausible |
Yellow |
||
EDC7UC31 |
100D5 |
ECU Hardware: Shut off during Initialization |
SOPTst |
02 |
02 |
Supply Voltage too high |
Yellow |
Power Reduction (Technical) |
|
04 12 |
04 0C |
Watchdog Supply Voltage too low |
|||||||
EDC7UC31 |
100D6 |
ECU Hardware: TPU Monitoring |
TPUMon |
12 |
0C |
Time deviation between System and TPU |
Yellow |
||
EDC7UC31 |
100D7 |
ECU Software: Variant Dataset failure |
VarMngCodDs |
02 12 |
02 0C |
Variant Dataset not valid Variant could not be set |
Red |
||
EDC7UC31 |
100D8 |
ECU Hardware: Controller Watchdog failure |
WdCom |
12 |
0C |
SPI Communication failure |
Yellow |
||
EDC7UC31 |
100D9 |
ADC Monitoring failure |
ADCMon |
02 03 04 12 |
02 03 04 0C |
Test Impulse Error Reference Voltage too high Reference Voltage too low Queue Error |
Yellow |
||
EDC7UC31 |
100E2 |
Immobilizer failure (no fuel release) |
ImmCtl |
4 |
04 |
Injection disabled |
Red |
||
EDC7UC31 |
100E3 |
Overrun Monitoring failure |
OvRMon |
3 |
03 |
Injection Time too long |
Red |
||
EDC7UC31 |
100E4 |
Redundant Engine Speed in Overrun Monitoring |
OvRMonSigA |
3 |
03 |
Speed Signal not plausible |
Red |
||
EDC7UC31 |
100E5 |
ECU Hardware: Sensor 12V Supply Voltage failure |
SSpMon12V |
03 04 |
03 04 |
Signal too high Signal too low |
Yellow |
||
EDC7UC31 |
100E6 |
ECU Hardware: Sensor Supply Voltage 1 failure |
SSpMon1 |
03 04 |
03 04 |
Signal too high Signal too low |
Yellow + MIL |
Power Reduction (Technical) Long Term Failure |
|
EDC7UC31 |
100E7 |
ECU Hardware: Sensor Supply Voltage 2 failure |
SSpMon2 |
03 04 |
03 04 |
Signal too high Signal too low |
Yellow |
||
EDC7UC31 |
100E8 |
ECU Hardware: Sensor Supply Voltage 3 failure |
SSpMon3 |
03 04 |
03 04 |
Signal too high Signal too low |
Yellow |
Power Reduction (Technical) |
|
EDC7UC31 |
100E9 |
ECU internal Supply Voltage too high |
HWEMonUMaxSupply |
3 |
03 |
Supply Voltage CJ940 above Limit |
Red |
||
EDC7UC31 |
100EA |
ECU internal Supply Voltage too low |
HWEMonUMinSupply |
4 |
04 |
Supply Voltage CJ940 below Limit |
Red |
||
EDC7UC31 |
100EB |
Atmospheric Pressure Sensor failure |
APSCD |
02 03 04 12 |
02 03 04 0C |
CAN Signal failure Signal too high Signal too low Signal not plausible to Reference Pressure (Boost or Exhaust) |
|||
EDC7UC31 |
20011 |
Vehicle Speed Sensor failure |
VSSCD2 |
02 03 04 12 |
02 03 04 0C |
CAN Signal failure Voltage too high Voltage too low Voltage not plausible |
|||
EDC7UC31 |
20015 |
Cruise Control Buttons irreversible failure |
MFLv_Irvrs |
12 |
0C |
Invalid Signal Combination |
|||
EDC7UC31 |
2001D |
SCR Catalyst Thermal Ageing Limit exceeded |
SCRCatAgeingIv |
3 |
03 |
Too High Catalyst Temperature for excessive |
Long Term Failure |
||
EDC7UC31 |
2001E |
SCR Catalyst Efficiency below first threshold |
SCRCatNOxLvl1Iv |
3 |
03 |
Nox above first OBD threshold (MIL On) |
MIL |
Long Term Failure |
|
EDC7UC31 |
2001F |
Current of Boost Pressure Actuator out of Range |
BPACOCurrOutRngIv |
3 |
03 |
Ratio of desired and measured BPA current out of range |
|||
EDC7UC31 |
20025 |
Main Relay failure (Interrupted Afterrun) |
MRlyCDAftRun |
3 |
03 |
Relay opened too early (Afterrun not completed) |
MIL |
||
EDC7UC31 |
20028 |
Main Relay 1 (Engine Brake Decompression Valve) Short to Ground |
MnRly1_SCG |
4 |
04 |
Short to Ground |
Yellow |
Long Term Failure |
|
EDC7UC31 |
20032 |
Coolant Temperature Test failure |
ClgAbsTst |
12 |
0C |
Minimum Temperature not reached in time |
Yellow |
||
EDC7UC31 |
20038 |
Oil Pressure too low |
OPSCD1 |
12 |
0C |
Value too low |
Yellow |
||
EDC7UC31 |
2003A |
Oil Temperature too high |
OTSCD1 |
12 |
0C |
Temperature too high |
Yellow |
||
EDC7UC31 |
2004A |
Engine Compartment Stop Button stuck |
ECBtCDStop |
2 |
2 |
Button stuck |
|||
EDC7UC31 |
2005F |
Info: Long Term Injection timing Failure |
OBDGFClct2 |
3 |
03 |
Long Term Fault present |
MIL |
Long Term Failure ( (not deletable until after 400 days) |
|
EDC7UC31 |
2007C |
ECU Hardware for Injection: CY33X Chip |
InjVlvChipB |
02 |
02 |
Test Mode |
Yellow |
||
specific failure (2) |
03 04 12 |
03 04 0C |
Internal reset — Clock loss — Voltage too low Unlocked — Init fail SPI Communication failure |
||||||
EDC7UC31 |
20092 |
Boost Pressure Actuator Short to Ground |
BPACD_Min |
4 |
04 |
Short to Ground |
Yellow |
Power Reduction (Technical) Long Term Failure |
|
EDC7UC31 |
20099 |
Turbocharger Control Underboost Pressure failure |
PCRUndBstIv |
3 |
03 |
Pressure too low |
Yellow + MIL |
||
EDC7UC31 |
2009D |
Info: Torque Limitation due to Negative Torque Coordinator |
NTCTrqLim |
4 |
04 |
Torque Limitation |
|||
EDC7UC31 |
200A2 |
NOx Sensor Drift failure |
SCRCatNOxDrIv |
3 |
03 |
Zero Drift detected |
MIL |
Power Reduction (OBD) Long Term Failure |
|
EDC7UC31 |
200A6 |
CAN Message timeout SCR2 (from DCU) |
FrmMngTOSCR2Iv |
02 |
02 |
No Signal |
Yellow + |
Power Reduction (OBD) |
|
04 |
04 |
Signal wrong |
MIL |
Long Term Failure |
|||||
EDC7UC31 |
200AE |
Info: Humidity Sensor possibly saturated with water droplets |
IAHSCD |
03 04 |
03 04 |
Signal Ratio above Limit Signal Ratio below Limit |
|||
EDC7UC31 |
200AF |
Info: DCU Error2 via CAN message DM1DCU |
FrmMngDM1SPN2Iv |
3 |
03 |
Error in DCU active |
MIL |
Power Reduction (OBD) |
|
EDC7UC31 |
200B4 |
CAN Message timeout BC2EDC2 (from Body Computer) |
FrmMngTOBC2EDC2Iv |
02 04 |
02 04 |
No Signal Signal wrong |
Yellow |
||
EDC7UC31 |
200C2 |
CAN Message timeout ETC2 (from Electronic Transmission Controller) |
FrmMngTOETC2 |
2 |
02 |
CAN timeout |
|||
EDC7UC31 |
200C6 |
CAN Message timeout inactive TSC1-PE (Torque/Speed Control Request from PTO to Engine) |
FrmMngTOTSC1PEPasIv |
02 04 |
02 04 |
No Signal Signal wrong |
Yellow |
||
EDC7UC31 |
200C8 |
CAN Message timeout active TSC1-VR (Torque/Speed Control Request from VCM/BC to Retarder) |
FrmMngTOTSC1VRActIv |
3 |
03 |
CAN timeout |
Yellow |
||
EDC7UC31 |
200C9 |
Time/Date CAN timeout (from Tachograph or VCM) |
FrmMngTOTimeDateIv |
02 04 |
02 04 |
No Signal Signal wrong |
|||
EDC7UC31 |
200D3 |
ECU recovery — suppressed |
HWEMonRcySuppressed |
12 |
0C |
Recovery occurred |
Red |
||
EDC7UC31 |
30015 |
Cruise Control Buttons reversible failure |
MFLv_Rvrs |
12 |
0C |
Invalid Signal Combination |
|||
EDC7UC31 |
3001D |
DCU State Monitoring |
SCRCatDCUStateIv |
3 |
03 |
DCU not ready in time |
MIL |
Power Reduction (OBD) Long Term Failure |
ECU Name |
SPN [Hex] |
Fault Component |
Description |
FMI [DEC] |
FMI [HEX] |
FMI Description |
Lamp status |
Comment |
|
EDC7UC31 |
3001E |
SCR Catalyst Efficiency below second threshold |
SCRCatNOxLvl2Iv |
3 |
03 |
Nox above second OBD threshold (Performance limitation) |
MIL |
Power Reduction (OBD) Long Term Failure |
|
EDC7UC31 |
3001F |
SCR Catalyst System Efficiency too high |
SCRCatHiEffIv |
3 |
03 |
Efficiency too high |
Yellow |
Long Term Failure |
|
EDC7UC31 |
3005F |
Info: Long Term air system failure |
OBDGFClct3 |
3 |
03 |
Long Term Fault present |
MIL |
Long Term Failure ( (not deletable until after 400 days) |
|
EDC7UC31 |
30092 |
Boost Pressure Power Stage open load or high Temperature |
BPACD_SigNpl |
02 12 |
02 0C |
Open Load Temperature too high |
Yellow |
Long Term Failure |
|
EDC7UC31 |
3009E |
Info: Torque Limitation due to Turbo Charger Protection |
BstPrtTrqLim |
4 |
04 |
Torque Limitation |
|||
EDC7UC31 |
300A2 |
NOx Sensor Plausibility failure |
SCRCatNOxPlIv |
3 |
03 |
Difference between measured and simulated Value not plausible |
MIL |
Power Reduction (OBD) Long Term Failure |
|
EDC7UC31 |
300C8 |
CAN Message timeout inactive TSC1-VE (Torque/Speed Control Request from VCM/BC to Engine) |
FrmMngTOTSC1VEPasIv |
02 04 |
02 04 |
No Signal Signal wrong |
Yellow |
||
EDC7UC31 |
300C9 |
CAN Message timeout HRVD (from Tachograph — High Resolution Vehicle Distance) |
FrmMngTOHRVDIv |
02 04 |
02 04 |
No Signal Signal wrong |
|||
EDC7UC31 |
300D3 |
ECU recovery — visible |
HWEMonRcyVisible |
12 |
0C |
Recovery occurred |
Red |
||
EDC7UC31 |
4005F |
Info: Long Term NOx Sensor Failure |
OBDGFClct4 |
3 |
03 |
Long Term Fault present |
MIL |
Long Term Failure ( (not deletable until after 400 days) |
|
EDC7UC31 |
4009E |
Info: Torque Limitation due to Engine Protection (against Excessive Torque, Engine Overspeed and Overheat) |
EngPrtTrqLim |
4 |
04 |
Torque Limitation |
|||
EDC7UC31 |
400AF |
Info: DCU Error4 via CAN message DM1DCU |
FrmMngDM1SPN4Iv |
3 |
03 |
Error in DCU active |
MIL |
Power Reduction (OBD) |
|
EDC7UC31 |
400C8 |
CAN Message timeout inactive TSC1-VR (Torque/Speed Control Request from VCM/BC to Retarder) |
FrmMngTOTSC1VRPasIv |
02 04 |
02 04 |
No Signal Signal wrong |
Yellow |
||
EDC7UC31 |
5005F |
Info: Long Term SCR System Failure |
OBDGFClct5 |
3 |
03 |
Long Term Fault present |
MIL |
Long Term Failure ( (not deletable until after 400 days) |
|
EDC7UC31 |
5009D |
Info: Torque Limitation due to SCR Catalyst Overheat Protection |
SCRPrtTrqLim |
4 |
04 |
Torque Limitation |
|||
EDC7UC31 |
500AF |
Info: DCU Error5 via CAN message DM1DCU |
FrmMngDM1SPN5Iv |
3 |
03 |
Error in DCU active |
MIL |
Power Reduction (OBD) |
|
EDC7UC31 |
6009E |
Info: Torque Limitation due to Fuel Quantity Limitation because of Injection System Errors |
QLimTrqLim |
4 |
04 |
Torque Limitation |
|||
ETC ZF ET2 |
40302 |
Short circuit to ground at output stage to Y2 (Valve Splitter; DD: high, OD: low) |
5 |
05 |
Shorted to low source |
Red |
|||
ETC ZF ET2 |
40303 |
Short circuit to ground at output stage to Y3 (Valve Splitter; DD: low, OD: high) |
5 |
05 |
Shorted to low source |
Red |
|||
ETC ZF ET2 |
40304 |
Short circuit to ground at output stage to Y4 (Valve Select) |
5 |
05 |
Shorted to low source |
Red |
|||
ETC ZF ET2 |
40305 |
Short circuit to ground at output stage to Y5 (Valve Select) |
5 |
05 |
Shorted to low source |
Red |
|||
ETC ZF ET2 |
40306 |
Short circuit to ground at output stage to Y6 (Valve Shift) |
5 |
05 |
Shorted to low source |
Red |
|||
ETC ZF ET2 |
40307 |
Short circuit to ground at output stage to Y7 (Valve Shift) |
5 |
05 |
Shorted to low source |
Red |
|||
ETC ZF ET2 |
40308 |
Short circuit to ground at output stage to Y8 (Valve Range) |
5 |
05 |
Shorted to low source |
Red |
|||
ETC ZF ET2 |
40309 |
Short circuit to ground at output stage to Y9 (Valve Range) |
5 |
05 |
Shorted to low source |
Red |
|||
ETC ZF ET2 |
4030A |
Short circuit to ground at output stage to Y10 (Main valve) |
5 |
05 |
Shorted to low source |
Red |
|||
ETC ZF ET2 |
4030B |
Short circuit to positive at output stage to warning buzzer (shift lever) |
0 |
00 |
No fault sympton available for this DTC |
Yellow |
|||
ETC ZF ET2 |
4030C |
Short circuit to ground at output stage to reverse light relay (shift lever) |
0 |
00 |
No fault sympton available for this DTC |
Yellow |
|||
ETC ZF ET2 |
4030D |
Short circuit to ground at output stage to PTO 1 |
0 |
00 |
No fault sympton available for this DTC |
Red |
|||
ETC ZF ET2 |
4030E |
Short circuit to ground at output stage to PTO 2 |
0 |
00 |
No fault sympton available for this DTC |
Red |
|||
ETC ZF ET2 |
40311 |
Short circuit to ground at output stage to Y1 (inertia brake valve) |
5 |
05 |
Shorted to low source |
Yellow |
|||
ETC ZF ET2 |
40312 |
Short circuit to ground at output stage to small diseng. clutch valve |
5 |
05 |
Shorted to low source |
Yellow |
|||
ETC ZF ET2 |
40313 |
Short circuit to ground at output stage to small eng. clutch valve |
5 |
05 |
Shorted to low source |
Yellow |
|||
ETC ZF ET2 |
40314 |
Short circuit to ground at output stage to large diseng. clutch valve |
5 |
05 |
Shorted to low source |
Yellow |
|||
ETC ZF ET2 |
40315 |
Short circuit to ground at output stage to large eng. clutch valve |
5 |
05 |
Shorted to low source |
Yellow |
|||
ETC ZF ET2 |
40316 |
Short circuit to ground at output ADVP (wakeup control signal for shift lever, voltage supply to display, warning buzzer, output speed sensor 1) |
5 |
05 |
Shorted to low source |
Red |
|||
ETC ZF ET2 |
40319 |
Short circuit to ground at output SD to display |
0 |
00 |
No fault sympton available for this DTC |
Yellow |
|||
ETC ZF ET2 |
4031A |
CAN engine configuration timeout |
4 |
04 |
No signal |
Yellow |
|||
ETC ZF ET2 |
4031B |
Error on ”engine configuration message” (engine configuration) |
8 |
08 |
Invalid signal |
Yellow |
|||
ETC ZF ET2 |
4031C |
Error on ”Actual driveline retarder — percent torque” signal (ERC1_DR) |
8 |
08 |
Invalid signal |
Yellow |
|||
ETC ZF ET2 |
4031D |
Error on ”Engine coolant load increase” signal (ERC1_DR) |
8 |
08 |
Invalid signal |
Yellow |
|||
ETC ZF ET2 |
4031E |
Error on ”Driveline retarder configuration message” (Driveline retarder configuration) |
8 |
08 |
Invalid signal |
Yellow |
|||
ETC ZF ET2 |
4031F |
Error on ”Actual engine retarder — percent torque” signal (ERC1_ER) |
8 |
08 |
Invalid signal |
Yellow |
|||
ETC ZF ET2 |
40320 |
Error on ”Engine retarder configuration message” (Engine retarder configuration) |
8 |
08 |
Invalid signal |
Yellow |
|||
ETC ZF ET2 |
40321 |
CAN ”Engine retarder configuration” timeout |
4 |
04 |
No signal |
Yellow |
|||
ETC ZF ET2 |
40322 |
Interruption at output stage to Y2 (Valve Splitter) |
10 |
0A |
Disconnection |
Red |
|||
ETC ZF ET2 |
40323 |
Interruption at output stage to Y3 (Valve Splitter) |
10 |
0A |
Disconnection |
Red |
|||
ETC ZF ET2 |
40324 |
Interruption at output stage to Y4 (Valve Select) |
10 |
0A |
Disconnection |
Red |
|||
ETC ZF ET2 |
40325 |
Interruption at output stage to Y5 (Valve Select) |
10 |
0A |
Disconnection |
Red |
|||
ETC ZF ET2 |
40326 |
Interruption at output stage to Y6 (Valve Shift) |
10 |
0A |
Disconnection |
Red |
|||
ETC ZF ET2 |
403 27 |
Interruption at output stage to Y7 (Valve Shift) |
10 |
0A |
Disconnection |
Red |
|||
ETC ZF ET2 |
40328 |
Interruption at output stage to Y8(Valve Range) |
10 |
0A |
Disconnection |
Red |
|||
ETC ZF ET2 |
40329 |
Interruption at output stage to Y9 (Valve Range) |
10 |
0A |
Disconnection |
Red |
|||
ETC ZF ET2 |
4032A |
Interruption at output stage to Y10 (Main valve) |
10 |
0A |
Disconnection |
Red |
|||
ETC ZF ET2 |
4032B |
Interruption at output to warning buzzer |
0 |
00 |
No fault sympton available for this DTC |
Yellow |
|||
ETC ZF ET2 |
4032C |
Interruption at output stage to reverse light relay |
0 |
00 |
No fault sympton available for this DTC |
Yellow |
|||
ETC ZF ET2 |
4032D |
Interruption at output stage to PTO 1 |
0 |
00 |
No fault sympton available for this DTC |
Yellow |
|||
ETC ZF ET2 |
4032E |
Interruption at output stage to PTO 2 |
0 |
00 |
No fault sympton available for this DTC |
Yellow |
|||
ETC ZF ET2 |
40331 |
Interruption at output stage to Y1 (inertia brake valve) |
10 |
0A |
Disconnection |
Yellow |
|||
ETC ZF ET2 |
40332 |
Interruption at output stage to small disengagement clutch valve |
10 |
0A |
Disconnection |
Yellow |
|||
ETC ZF ET2 |
40333 |
Interruption at output stage to small engagement clutch valve |
10 |
0A |
Disconnection |
Yellow |
|||
ETC ZF ET2 |
40334 |
Interruption at output stage to large disengagement clutch valve |
10 |
0A |
Disconnection |
Yellow |
|||
ETC ZF ET2 |
40335 |
Interruption at output stage to large engagement clutch valve |
10 |
0A |
Disconnection |
Yellow |
|||
ETC ZF ET2 |
40336 |
Interruption at output ADVP |
10 |
0A |
Disconnection |
Red |
|||
ETC ZF ET2 |
4033B |
Acknowledge fault of PTO 1 |
8 |
08 |
Invalid signal |
Yellow |
|||
ETC ZF ET2 |
4033C |
Acknowledge fault of PTO 2 |
8 |
08 |
Invalid signal |
Yellow |
|||
ETC ZF ET2 |
4033D |
Disengagement fault of PTO 1 |
8 |
08 |
Invalid signal |
Red |
|||
ETC ZF ET2 |
4033E |
Disengagement fault of PTO 2 |
8 |
08 |
Invalid signal |
Red |
|||
ETC ZF ET2 |
4033F |
Engagement fault of PTO1 |
8 |
08 |
Invalid signal |
Yellow |
|||
ETC ZF ET2 |
40340 |
Engagement fault of PTO2 |
8 |
08 |
Invalid signal |
Yellow |
|||
ETC ZF ET2 |
40342 |
Short circuit to positive at output stage to Y2 (Valve Splitter) |
6 |
06 |
Shorted to high source |
Red |
|||
ETC ZF ET2 |
40343 |
Short circuit to positive at output stage to Y3 (Valve Splitter) |
6 |
06 |
Shorted to high source |
Red |
|||
ETC ZF ET2 |
40344 |
Short circuit to positive at output stage to Y4 (Valve Select) |
6 |
06 |
Shorted to high source |
Red |
|||
ETC ZF ET2 |
40345 |
Short circuit to positive at output stage to Y5 (Valve Select) |
6 |
06 |
Shorted to high source |
Red |
|||
ETC ZF ET2 |
40346 |
Short circuit to positive at output stage to Y6 (Valve Shift) |
6 |
06 |
Shorted to high source |
Red |
|||
ETC ZF ET2 |
40347 |
Short circuit to positive at output stage to Y7 (Valve Shift) |
6 |
06 |
Shorted to high source |
Red |
|||
ETC ZF ET2 |
40348 |
Short circuit to positive at output stage to Y8 (Valve range low) |
6 |
06 |
Shorted to high source |
Red |
|||
ETC ZF ET2 |
40349 |
Short circuit to positive at output stage to Y9 (Valve range high) |
6 |
06 |
Shorted to high source |
Red |
|||
ETC ZF ET2 |
4034A |
Short circuit to positive at output stage to Y10 (Main valve) |
6 |
06 |
Shorted to high source |
Yellow |
|||
ETC ZF ET2 |
4034B |
Short circuit to ground at output stage to warning buzzer (shift-lever) |
6 |
06 |
Shorted to high source |
Yellow |
|||
ETC ZF ET2 |
4034C |
Short circuit to positive at output stage to reverse light relay |
6 |
06 |
Shorted to high source |
Yellow |
|||
ETC ZF ET2 |
4034D |
Short circuit to positive at output stage to PTO 1 |
6 |
06 |
Shorted to high source |
Yellow |
|||
ETC ZF ET2 |
4034E |
Short circuit to positive at output stage to PTO 2 |
6 |
06 |
Shorted to high source |
Yellow |
|||
ETC ZF ET2 |
40351 |
Short circuit to positive at output stage to Y1 (inertia brake valve) |
6 |
06 |
Shorted to high source |
Yellow |
|||
ETC ZF ET2 |
40352 |
Short circuit to positive at output stage to small diseng. clutch valve |
6 |
06 |
Shorted to high source |
Red |
ECU Name |
SPN [Hex] |
Fault Component |
Description |
FMI [DEC] |
FMI [HEX] |
FMI Description |
Lamp status |
Comment |
ETC ZF ET2 |
40353 |
Short circuit to positive at output stage to small eng. clutch valve |
6 |
06 |
Shorted to high source |
Red |
||
ETC ZF ET2 |
40354 |
Short circuit to positive at output stage to large diseng. clutch valve |
6 |
06 |
Shorted to high source |
Red |
||
ETC ZF ET2 |
40355 |
Short circuit to positive at output stage to large eng. clutch valve |
6 |
06 |
Shorted to high source |
Red |
||
ETC ZF ET2 |
40356 |
Short circuit to positive at output ADVP (wakeup control signal for shift-lever, voltage supply to display, warning buzzer, output speed sensor 1) |
6 |
06 |
Shorted to high source |
Yellow |
||
ETC ZF ET2 |
40359 |
Short circuit to positive at output SD to display |
0 |
00 |
No fault sympton available for this DTC |
Yellow |
||
ETC ZF ET2 |
4035A |
Communication error between controller 1 and controller 2 (ECU failure) |
9 |
09 |
Device error |
Red |
||
ETC ZF ET2 |
4035B |
CAN EBC1 timeout |
4 |
04 |
No signal |
Yellow |
||
ETC ZF ET2 |
4035C |
Error on ”ABS active” signal (EBC1) |
8 |
08 |
Invalid signal |
Yellow |
||
ETC ZF ET2 |
4035D |
Error on ”ASR engine control active” signal (EBC1) |
8 |
08 |
Invalid signal |
Yellow |
||
ETC ZF ET2 |
4035E |
Error on ”ASR brake control active” signal (EBC1) |
8 |
08 |
Invalid signal |
Yellow |
||
ETC ZF ET2 |
4035F |
Error on ”Cruise control active” signal (CCVS) |
8 |
08 |
Invalid signal |
Yellow |
||
ETC ZF ET2 |
40360 |
Error on ”Cruise control set speed” (CCVS) |
8 |
08 |
Invalid signal |
Yellow |
||
ETC ZF ET2 |
40361 |
Error on ”Engine speed” signal (EEC1) |
8 |
08 |
Invalid signal |
Yellow |
||
ETC ZF ET2 |
40362 |
Error on transmission input speed signal |
8 |
08 |
Invalid signal |
Yellow |
||
ETC ZF ET2 |
40363 |
Error on output speed signal 1 |
8 |
08 |
Invalid signal |
Yellow |
||
ETC ZF ET2 |
40364 |
Error on output speed signal 2 |
8 |
08 |
Invalid signal |
Yellow |
||
ETC ZF ET2 |
40365 |
Error on both output speed signals |
8 |
08 |
Invalid signal |
Red |
||
ETC ZF ET2 |
40366 |
Plausibility error between transmission input |
3 |
03 |
Not plausible |
Yellow |
||
ETC ZF ET2 |
40367 |
CAN CCVS error on wheel based vehicle |
0 |
00 |
No fault sympton available for this DTC |
Yellow |
||
ETC ZF ET2 |
40368 |
High voltage (Vehicle electrical system voltage too high) |
1 |
01 |
Above maximum range |
Yellow |
||
ETC ZF ET2 |
40369 |
Low voltage (Vehicle electrical system voltage too low) |
2 |
02 |
Below maximum threshold |
Red |
||
ETC ZF ET2 |
4036B |
Stabilised voltage supply at output AU (clutch sensor supply) out of valid range |
2 |
02 |
Below maximum threshold |
Yellow |
||
ETC ZF ET2 |
4036C |
Error in selector lever or tip lever |
0 |
00 |
No fault sympton available for this DTC |
Yellow |
||
ETC ZF ET2 |
4036E |
Lever CAN timeout |
0 |
00 |
No fault sympton available for this DTC |
Yellow |
||
ETC ZF ET2 |
40371 |
Error on «Driveline retarder configuration timeout» |
4 |
04 |
No signal |
Yellow |
||
ETC ZF ET2 |
40372 |
Clutch engaged unintentionally in standstill, gear engaged |
0 |
00 |
No fault sympton available for this DTC |
Red |
||
ETC ZF ET2 |
40375 |
Error in clutch self-adjustment process |
0 |
00 |
No fault sympton available for this DTC |
Red |
||
ETC ZF ET2 |
40376 |
Clutch does not disengage |
0 |
00 |
No fault sympton available for this DTC |
Red |
||
ETC ZF ET2 |
40377 |
Clutch does not engage / does not transmit engine torque |
0 |
00 |
No fault sympton available for this DTC |
Red |
||
ETC ZF ET2 |
40378 |
Mechanical failure of small disengagement clutch valve |
0 |
00 |
No fault sympton available for this DTC |
Yellow |
||
ETC ZF ET2 |
40379 |
Mechanical failure of large disengagement clutch valve |
0 |
00 |
No fault sympton available for this DTC |
Yellow |
||
ETC ZF ET2 |
4037A |
Mechanical failure of small engagement clutch valve |
0 |
00 |
No fault sympton available for this DTC |
Yellow |
||
ETC ZF ET2 |
4037B |
Mechanical failure of large engagement clutch valve |
0 |
00 |
No fault sympton available for this DTC |
Yellow |
||
ETC ZF ET2 |
4037C |
Error on clutch travel signal |
0 |
00 |
No fault sympton available for this DTC |
Yellow |
||
ETC ZF ET2 |
4037E |
Error on pressure sensor signal |
3 |
03 |
Not plausible |
Yellow |
||
ETC ZF ET2 |
4037F |
Error on ECU temperature sensor signal |
3 |
03 |
Not plausible |
Yellow |
||
ETC ZF ET2 |
40380 |
Error on oil temperature sensor signal |
0 |
00 |
No fault sympton available for this DTC |
Yellow |
||
ETC ZF ET2 |
40381 |
No shift sensor signal (Short circuit to positive) |
6 |
06 |
Shorted to high source |
Yellow |
||
ETC ZF ET2 |
40382 |
No shift sensor signal (Short circuit to ground) |
5 |
05 |
Shorted to low source |
Yellow |
||
ETC ZF ET2 |
40383 |
No shift sensor signal (Interruption) |
10 |
0A |
Disconnection |
Yellow |
||
ETC ZF ET2 |
40384 |
Self adjustment error of shift sensor |
0 |
00 |
No fault sympton available for this DTC |
Red |
||
ETC ZF ET2 |
40385 |
No gate select sensor signal (Short circuit to positive) |
6 |
06 |
Shorted to high source |
Yellow |
||
ETC ZF ET2 |
40386 |
No gate select sensor signal (Short circuit to ground) |
5 |
05 |
Shorted to low source |
Yellow |
||
ETC ZF ET2 |
40387 |
No gate select sensor signal (Interruption) |
10 |
0A |
Disconnection |
Yellow |
||
ETC ZF ET2 |
40388 |
Gate select sensor self adjustment error |
0 |
00 |
No fault sympton available for this DTC |
Red |
||
ETC ZF ET2 |
40389 |
No range change group (GP) sensor signal (Short circuit to positive) |
6 |
06 |
Shorted to high source |
Yellow |
||
ETC ZF ET2 |
4038A |
No range change group (GP) sensor signal (Short circuit to ground) |
5 |
05 |
Shorted to low source |
Yellow |
||
ETC ZF ET2 |
4038B |
No range change group (GP) sensor signal (Interruption) |
10 |
0A |
Disconnection |
Yellow |
||
ETC ZF ET2 |
4038C |
Self adjustment error of range change group sensor in position fast |
0 |
00 |
No fault sympton available for this DTC |
Red |
||
ETC ZF ET2 |
4038D |
No splitter group (GV) sensor signal (Short circuit to positive) |
6 |
06 |
Shorted to high source |
Yellow |
||
ETC ZF ET2 |
4038E |
No splitter group (GV) sensor signal (Short circuit to ground) |
5 |
05 |
Shorted to low source |
Yellow |
||
ETC ZF ET2 |
4038F |
No splitter group (GV) sensor signal (Interruption) |
10 |
0A |
Disconnection |
Yellow |
||
ETC ZF ET2 |
40390 |
Splitter group (GV) sensor self adjustment error |
0 |
00 |
No fault sympton available for this DTC |
Red |
||
ETC ZF ET2 |
40391 |
Range change group (GP) disengagement error |
0 |
00 |
No fault sympton available for this DTC |
Yellow |
||
ETC ZF ET2 |
40392 |
Changeover error during range change group (GP) shifting |
0 |
00 |
No fault sympton available for this DTC |
Yellow |
||
ETC ZF ET2 |
40393 |
Range change group (GP) does not engage |
0 |
00 |
No fault sympton available for this DTC |
Red |
||
ETC ZF ET2 |
40394 |
Splitter (GV) does not disengage |
0 |
00 |
No fault sympton available for this DTC |
Yellow |
||
ETC ZF ET2 |
40395 |
Change over error during splitter shifting |
0 |
00 |
No fault sympton available for this DTC |
Yellow |
||
ETC ZF ET2 |
40396 |
Splitter (GV) does not engage |
0 |
00 |
No fault sympton available for this DTC |
Red |
||
ETC ZF ET2 |
40397 |
Selector cylinder does not disengage |
0 |
00 |
No fault sympton available for this DTC |
Yellow |
||
ETC ZF ET2 |
40398 |
Change over error during gate selection procedure |
0 |
00 |
No fault sympton available for this DTC |
Yellow |
||
ETC ZF ET2 |
40399 |
Selector cylinder does not engage |
0 |
00 |
No fault sympton available for this DTC |
Red |
||
ETC ZF ET2 |
4039A |
Main transmission gear does not disengage |
0 |
00 |
No fault sympton available for this DTC |
Red |
||
ETC ZF ET2 |
4039B |
Main transmission gear does not engage |
0 |
00 |
No fault sympton available for this DTC |
Red |
||
ETC ZF ET2 |
4039C |
Wrong gear shifting |
0 |
00 |
No fault sympton available for this DTC |
Red |
||
ETC ZF ET2 |
4039E |
Shift sensor signal leaves engaged position during driving |
0 |
00 |
No fault sympton available for this DTC |
Yellow |
||
ETC ZF ET2 |
4039F |
Range-change group sensor signal leaves engaged position during driving |
0 |
00 |
No fault sympton available for this DTC |
Yellow |
||
ETC ZF ET2 |
403A0 |
Splitter sensor signal leaves engaged position during driving |
0 |
00 |
No fault sympton available for this DTC |
Yellow |
||
ETC ZF ET2 |
403A3 |
Engine does not react on torque intervention |
0 |
00 |
No fault sympton available for this DTC |
Yellow |
||
ETC ZF ET2 |
403A4 |
Error on ”Drivers demand engine percent torque” (EEC1) |
8 |
08 |
Invalid signal |
Yellow |
||
ETC ZF ET2 |
403A5 |
Error on ”Accelerator pedal position” (EEC2) |
8 |
08 |
Invalid signal |
Yellow |
||
ETC ZF ET2 |
403A6 |
Permanent idle signal |
0 |
00 |
No fault sympton available for this DTC |
Yellow |
||
ETC ZF ET2 |
403A8 |
No idle signal or error on ”idle signal switch” signal (EEC2) or never active «idle signal» |
8 |
08 |
Invalid signal |
Yellow |
||
ETC ZF ET2 |
403A9 |
Cut-off relay in ECU does not switch off |
0 |
00 |
No fault sympton available for this DTC |
Red |
||
ETC ZF ET2 |
403AA |
No voltage supply at pin 30 or cut-off relay in ECU does not switch on |
0 |
00 |
No fault sympton available for this DTC |
Red |
||
ETC ZF ET2 |
403AB |
Error on ”Actual engine percent torque” signal (EEC1) |
8 |
08 |
Invalid signal |
Yellow |
||
ETC ZF ET2 |
403AE |
Error on ”Kickdown switch” signal (EEC2) |
8 |
08 |
Invalid signal |
Yellow |
||
ETC ZF ET2 |
403AF |
Error on ”Ignition lock” signal (terminal 15) |
4 |
04 |
No signal |
Yellow |
||
ETC ZF ET2 |
403B1 |
System-CAN Busoff error |
4 |
04 |
No signal |
Red |
||
ETC ZF ET2 |
403B2 |
CAN Errorwarning |
4 |
04 |
No signal |
Red |
||
ETC ZF ET2 |
403B3 |
CAN queue overrun |
0 |
00 |
No fault sympton available for this DTC |
Red |
||
ETC ZF ET2 |
403B4 |
CAN EEC1 timeout |
4 |
04 |
No signal |
Red |
||
ETC ZF ET2 |
403B5 |
CAN EEC2 timeout |
4 |
04 |
No signal |
Red |
||
ETC ZF ET2 |
403B6 |
CAN CCVS timeout |
4 |
04 |
No signal |
Yellow |
||
ETC ZF ET2 |
403B7 |
CAN ERC1_ER timeout |
4 |
04 |
No signal |
Yellow |
||
ETC ZF ET2 |
403B8 |
CAN ERC1_DR timeout |
4 |
04 |
No signal |
Yellow |
||
ETC ZF ET2 |
403BC |
ECU fault — wrong interrupt |
0 |
00 |
No fault sympton available for this DTC |
Red |
||
ETC ZF ET2 |
403BD |
ECU fault — stack watch |
0 |
00 |
No fault sympton available for this DTC |
Red |
||
ETC ZF ET2 |
403BE |
EOL EEPROM parameter out of valid range |
0 |
00 |
No fault sympton available for this DTC |
Red |
||
ETC ZF ET2 |
403BF |
EOL EEPROM parameter checksum error |
0 |
00 |
No fault sympton available for this DTC |
Red |
||
ETC ZF ET2 |
403C0 |
ECU fault — EEPROM access failure |
0 |
00 |
No fault sympton available for this DTC |
Yellow |
||
ETC ZF ET2 |
403C1 |
ECU temperature too high |
1 |
01 |
Above maximum range |
Red |
||
ETC ZF ET2 |
403C2 |
Both sources for front axle speed not available |
0 |
00 |
No fault sympton available for this DTC |
Yellow |
||
ETC ZF ET2 |
403C5 |
Error on «Front axle speed» (WSI) |
8 |
08 |
Invalid signal |
Yellow |
||
ETC ZF ET2 |
403C7 |
CAN WSI timeout |
4 |
04 |
No signal |
Yellow |
||
ETC ZF ET2 |
403E2 |
IVECO:CAN message BC_TC timeout |
0 |
00 |
No fault sympton available for this DTC |
Red |
||
ETC ZF ET2 |
403E3 |
Application-Error database for CANcommunication |
0 |
00 |
No fault sympton available for this DTC |
Red |
||
IC M06 |
41701 |
EEPROM checksum |
Physical memory fault.Checksum failure is detected |
12 |
0C |
Yellow |
||
IC M06 |
41702 |
Ignition Key (15) fault |
Signal not plausible with Ignition Key (15) over CAN |
11 |
0B |
Yellow |
||
IC M06 |
41703 |
Ignition Key (15) over CAN fault |
Signal not plausible with Ignition Key (15) |
12 |
0C |
Yellow |
||
IC M06 |
41704 |
Stepper Motor |
Defect, access not possible.Stepper motor failure is present. |
12 |
0C |
Yellow |
||
IC M06 |
41705 |
Fuel Level Sensor |
Fuel Level interface failure detected. Debounce time (for fault active andinactive conditions) is 4s. The input voltage is evaluated for in-range checking: |
3 |
03 |
Voltage above normal (s.c. to battery or open circuit) |
||
Yellow |
||||||||
IC M06 |
41706 |
Reserved for: Oil Level Sensor |
Yellow |
|||||
IC M06 |
41707 |
Ambient Temperature Sensor |
Ambient Temperature interface failure detected.Debounce time (for fault active and inactive conditions) is 4s.The input voltage is evaluated for inrange checking: |
03 04 |
03 04 |
Voltage above normal (s.c. to battery or open circuit) Voltage below normal (s.c. to ground) |
Yellow |
ECU Name |
SPN [Hex] |
Fault Component |
Description |
FMI [DEC] |
FMI [HEX] |
FMI Description |
Lamp status |
Comment |
IC M06 |
41708 |
Reserved for: OBD II Indicator Lamp (IL25) |
A fault of the Indicator Lamp or on its driving circuitry is detected… |
Yellow |
||||
IC M06 |
41709 |
12 |
0C |
Yellow |
||||
IC M06 |
4170A |
12 |
0C |
Yellow |
||||
IC M06 |
4170B |
Reserved for: CAN 2 Bus |
No CAN messages on CAN 2 or bus-off detection |
2 |
02 |
Red |
||
IC M06 |
4170C |
Vehicle Data Bus CAN |
No CAN messages on Vehicle Data Bus or bus-off detection |
2 |
02 |
Red |
||
IC M06 |
4170D |
Vehicle Data Bus — ECU#1 CAN |
No CAN messages from ECU#1 — IBC |
2 |
02 |
Red |
||
IC M06 |
4170E |
Vehicle Data Bus — ECU#2 CAN |
No CAN messages from ECU#2 — EDC or VCM |
2 |
02 |
Red |
||
IC M06 |
4170F |
Vehicle Data Bus — ECU#3 CAN |
No CAN messages from ECU#3 — TCO |
2 |
02 |
Red |
||
IC M06 |
41710 |
Vehicle Data Bus — ECU#4 CAN |
No CAN messages from ECU#4 — ETC |
2 |
02 |
Red |
||
IC M06 |
41711 |
Vehicle Data Bus — ECU#5 CAN |
No CAN messages from ECU#5 — EBC |
2 |
02 |
ABS Yellow tell tale |
||
IC M06 |
41712 |
Vehicle Data Bus — ECU#6 CAN |
No CAN messages from ECU#6 — ECAS |
2 |
02 |
Yellow |
||
IC M06 |
41713 |
Vehicle Data Bus — ECU#7 CAN |
No CAN messages from ECU#7 — Driveline Retarder |
2 |
02 |
Yellow |
||
IC M06 |
41714 |
Vehicle Data Bus — ECU#8 CAN |
No CAN messages from ECU#8 — Mirror Controller |
2 |
02 |
Yellow |
||
IC M06 |
41715 |
Vehicle Data Bus — ECU#9 CAN |
No CAN messages from ECU#9 — Expansion Module |
2 |
02 |
Yellow |
||
IC M06 |
41716 |
Vehicle Data Bus — ECU#10 CAN |
No CAN messages from ECU#10 — Steering Wheel Interface |
2 |
02 |
Yellow |
||
IC M06 |
41717 |
Vehicle Data Bus — ECU#11 CAN |
No CAN messages from ECU#11 — IVTM |
2 |
02 |
Yellow |
||
IC M06 |
41718 |
Vehicle Data Bus — ECU#12 CAN |
No CAN messages from ECU#12 — ADM |
2 |
02 |
Yellow |
||
IC M06 |
41719 |
Vehicle Data Bus — ECU#13 CAN |
No CAN messages from ECU#13 — SCR |
2 |
02 |
Yellow |
||
IC M06 |
4171A |
Vehicle Data Bus — ECU#14 CAN |
No CAN messages from ECU#14 — LDWS |
2 12 |
02 0C |
Yellow |
||
IC SPR1 E4 |
21701 |
EEPROM checksum |
Physical memory fault.Checksum failure is detected |
|||||
IC SPR1 E4 |
21704 |
Stepper Motor |
Defect, access not possible.Stepper motor failure is present. |
12 |
0C |
|||
IC SPR1 E4 |
21705 |
Fuel Level Sensor |
Fuel Level interface failure detected. Debounce time (for fault active andinactive conditions) is 4s. The input voltage is evaluated for in-range checking: |
3 |
03 |
Voltage above normal (s.c. to battery or open circuit) |
||
IC SPR1 E4 |
21706 |
Oil Level Sensor |
Oil level interface failure detected. The input voltage and the voltage difference between the first and the second acquisition are evaluated for inrange checking |
00 01 03 04 15 |
00 01 03 04 0F |
Delta voltage below normal Delta voltage above normal Voltage above normal (s.c. to battery or open circuit) Voltage below normal (s.c. to ground) Time/Date from TCO not available |
||
16 17 18 19 20 |
10 11 12 13 14 |
Engine Starter Mode from EDC not available Engine Oil Temperature from EDC not available Date could not be stored in EEPROM Time could not be stored in EEPROM Oil Level could not be stored in EEPROM |
||||||
IC SPR1 E4 |
21707 |
Ambient Temperature Sensor |
Ambient Temperature interface failure detected.Debounce time (for fault active and inactive conditions) is 4s.The input voltage is evaluated for inrange checking: |
03 04 |
03 04 |
Voltage above normal (s.c. to battery or open circuit) Voltage below normal (s.c. to ground) |
||
IC SPR1 E4 |
2170C |
Vehicle Data Bus CAN |
No CAN messages on Vehicle Data Bus or bus-off detection |
2 |
02 |
|||
IC SPR1 E4 |
2170D |
Vehicle Data Bus — ECU#1 CAN |
No CAN messages from ECU#1 — IBC |
2 |
02 |
|||
IC SPR1 E4 |
2170E |
Vehicle Data Bus — ECU#2 CAN |
No CAN messages from ECU#2 — EDC |
2 |
02 |
|||
IC SPR1 E4 |
2170F |
Vehicle Data Bus — ECU#3 CAN |
No CAN messages from ECU#3 — TCO |
2 |
02 |
|||
IC SPR1 E4 |
21710 |
Vehicle Data Bus — ECU#4 CAN |
No CAN messages from ECU#4 — ETC |
2 |
02 |
|||
IC SPR1 E4 |
21711 |
Vehicle Data Bus — ECU#5 CAN |
No CAN messages from ECU#5 — EBC |
2 |
02 |
|||
IC SPR1 E4 |
21712 |
Vehicle Data Bus — ECU#6 CAN |
No CAN messages from ECU#6 — ECAS |
2 |
02 |
|||
IC SPR1 E4 |
21713 |
Vehicle Data Bus — ECU#7 CAN |
No CAN messages from ECU#7 — Driveline Retarder |
2 |
02 |
|||
IC SPR1 E4 |
21714 |
Vehicle Data Bus — ECU#8 CAN |
No CAN messages from ECU#8 — Mirror Controller |
2 |
02 |
|||
IC SPR1 E4 |
21715 |
Vehicle Data Bus — ECU#9 CAN |
No CAN messages from ECU#8 — Expansion Module |
2 |
02 |
|||
EEC CRF MF3 |
40018 |
Sensore temperatura olio /pressione olio |
Segnale di temperatura |
01 02 |
01 02 |
C.a. o c.c. a Vbatt C.c. a Gnd |
Yellow |
|
EEC CRF MF3 |
40021 |
Sensore temperatura olio /pressione olio |
Segnale Pressione |
01 02 08 |
01 02 08 |
C.a. o c.c. a Vbatt C.c. a Gnd Avaria alimentazione sensore |
Yellow |
|
EEC CRF MF3 |
40017 |
Sensore temperatura/pressione gas rail valle riduttore (bassa pressione) |
Segnale di temperatura |
01 02 |
01 02 |
C.a. o c.c. a Vbatt C.c. a Gnd |
Yellow |
|
EEC CRF MF3 |
40025 |
Sensore temperatura/pressione gas rail valle riduttore (bassa pressione) |
Segnale Pressione |
01 02 08 |
01 02 08 |
C.a. o c.c. a Vbatt C.c. a Gnd Avaria alimentazione sensore |
Yellow |
|
EEC CRF MF3 |
40011 |
Sensore temperatura/pressione aria collettore |
Segnale di temperatura |
01 02 |
01 02 |
C.a. o c.c. a Vbatt C.c. a Gnd |
Yellow |
|
EEC CRF MF3 |
40026 |
Sensore temperatura/pressione gas rail |
Pressione troppo bassa |
2 |
02 |
Segnale sotto soglia min. |
Red |
|
EEC CRF MF3 |
40024 |
Sensore temperatura/pressione aria collettore |
Segnale di pressione |
01 02 08 |
01 02 08 |
C.a. o c.c. a Vbatt C.c. a Gnd Avaria alimentazione sensore |
Yellow |
|
EEC CRF MF3 |
40016 |
Sensore temperatura acqua |
01 |
01 |
C.a. o c.c. a Vbatt |
Yellow |
||
02 |
02 |
C.c. a Gnd |
||||||
EEC CRF MF3 |
40027 |
Sensore pressione GAS bombola monte riduttore (alta pressione) |
01 02 08 |
01 02 08 |
C.a. o c.c. a Vbatt C.c. a Gnd Avaria alimentazione sensore |
Yellow |
||
EEC CRF MF3 |
40012 |
Sensore temperatura scarico (postcatalizzatore) |
01 02 |
01 02 |
C.a. o c.c. a Vbatt C.c. a Gnd |
Yellow |
||
EEC CRF MF3 |
40083 |
Sensore Lambda pre-catalizzatore |
02 04 08 |
02 04 08 |
Sband. Magro Sband. Ricco Errore generico (5) |
Yellow |
||
EEC CRF MF3 |
40013 |
Temperatura catalizzatore (preallarme) |
3 |
03 |
Temperatura oltre soglia di preallarme |
Yellow |
||
EEC CRF MF3 |
40014 |
Temperatura catalizzatore (allarme) |
3 |
03 |
Temperatura oltre soglia di allarme |
Red |
||
EEC CRF MF3 |
40015 |
Temperatura catalizzatore (allarme memorizzato) |
8 |
08 |
Temperatura oltre soglia di allarme (1) |
Yellow |
||
EEC CRF MF3 |
40022 |
Sensore pressione valle compressore (sovralimentazione) |
01 02 08 |
01 02 08 |
C.a. o c.c. a Vbatt C.c. a Gnd Avaria alimentazione sensore |
Yellow |
||
EEC CRF MF3 |
40046 |
Tensione di batteria |
01 02 |
01 02 |
Segnale sopra soglia massima Segnale sotto soglia massima |
Yellow |
||
EEC CRF MF3 |
40055 |
Sensore di camma |
01 02 |
01 02 |
C.a. o c.c. a Vbatt C.c. a Gnd |
Yellow |
||
EEC CRF MF3 |
40056 |
Sensore di giri motore |
01 02 |
01 02 |
C.a. o c.c. a Vbatt C.c. a Gnd |
Red |
||
EEC CRF MF3 |
40023 |
Pressione atmosferica (interno alla ECU) |
01 02 |
01 02 |
C.a. o c.c. a Vbatt C.c. a Gnd |
Yellow |
||
EEC CRF MF3 |
40044 |
Relè carichi (comando in c.c. a Vbatt) |
1 |
01 |
Comando c.c. a Vbatt |
Red |
||
EEC CRF MF3 |
40043 |
Relè carichi (comando in c.a.) |
4 |
04 |
Comando in c.a. |
Red |
||
EEC CRF MF3 |
40045 |
Relè carichi (contatto incollato aperto oppure comando in c.a.) |
8 |
08 |
Relè incollato aperto oppure comando in c.a. |
Red |
||
EEC CRF MF3 |
40041 |
Relè carichi (contatto incollato chiuso) |
1 |
01 |
Relè incollato chiuso |
Yellow |
||
EEC CRF MF3 |
40042 |
Relè carichi (comando in c.c. a Gnd) |
2 |
02 |
Comando c.c. a Gnd |
Yellow |
||
EEC CRF MF3 |
40071 |
Iniettore 1 |
01 02 03 04 05 06 |
01 02 03 04 05 06 |
C.c. lato caldo a Vbatt C.c lato caldo a Gnd C.c tra lato caldo e lato freddo Circuito aperto C.c lato freddo a Vbatt C.c lato freddo a Gnd |
Yellow |
||
EEC CRF MF3 |
40072 |
Iniettore 2 |
01 02 03 04 05 06 |
01 02 03 04 05 06 |
C.c. lato caldo a Vbatt C.c lato caldo a Gnd C.c tra lato caldo e lato freddo Circuito aperto C.c lato freddo a Vbatt C.c lato freddo a Gnd |
Yellow |
||
EEC CRF MF3 |
40073 |
Iniettore 3 |
01 02 03 04 05 06 |
01 02 03 04 05 06 |
C.c. lato caldo a Vbatt C.c lato caldo a Gnd C.c tra lato caldo e lato freddo Circuito aperto C.c lato freddo a Vbatt C.c lato freddo a Gnd |
Yellow |
||
EEC CRF MF3 |
40074 |
Iniettore 4 |
01 02 03 04 05 06 |
01 02 03 04 05 06 |
C.c. lato caldo a Vbatt C.c lato caldo a Gnd C.c tra lato caldo e lato freddo Circuito aperto C.c lato freddo a Vbatt C.c lato freddo a Gnd |
Yellow |
||
EEC CRF MF3 |
40075 |
Iniettore 5 |
1 |
01 |
C.c. lato caldo a Vbatt |
Yellow |
||
EEC CRF MF3 |
40075 |
Iniettore 5 |
01 02 03 04 05 |
01 02 03 04 05 |
C.c. lato caldo a Vbatt C.c lato caldo a Gnd C.c tra lato caldo e lato freddo Circuito aperto C.c lato freddo a Vbatt |
Yellow |
||
06 |
06 |
C.c lato freddo a Gnd |
||||||
EEC CRF MF3 |
40076 |
Iniettore 6 |
01 02 03 04 05 06 |
01 02 03 04 05 06 |
C.c. lato caldo a Vbatt C.c lato caldo a Gnd C.c tra lato caldo e lato freddo Circuito aperto C.c lato freddo a Vbatt C.c lato freddo a Gnd |
Yellow |
||
EEC CRF MF3 |
40032 |
Elettrovalvola CNG su riduttore pressione (comando in c.c. a Vbatt o comando in c.a.) |
01 04 |
01 04 |
C.a. o c.c. a Vbatt Circuito aperto |
Red |
||
EEC CRF MF3 |
40031 |
Elettrovalvola CNG su riduttore pressione (comando in c.c. a Gnd) |
2 |
02 |
C.c. a Gnd |
Yellow |
||
EEC CRF MF3 |
40036 |
Elettrovalvola CNG su bombole (comando in c.c. a Vbatt o comando in c.a.) |
01 04 |
01 04 |
C.a. o c.c. a Vbatt Circuito aperto |
Red |
||
EEC CRF MF3 |
40034 |
Elettrovalvola CNG su bombole (comando in c.c. Gnd) |
2 |
02 |
C.c. a Gnd |
Yellow |
||
EEC CRF MF3 |
40082 |
Riscaldatore sonda Lambda |
01 02 04 |
01 02 04 |
C.c. a Vbatt C.c. a Gnd Circ. aperto |
Yellow |
||
EEC CRF MF3 |
40061 |
Bobina di accensione 1 |
01 02 03 08 |
01 02 03 08 |
C.c. a Vbatt Circ.aperto oppure C.c. a Gnd Surriscaldamento Errore Generico |
Yellow |
||
EEC CRF MF3 |
40062 |
Bobina di accensione 2 |
01 |
01 |
C.c. a Vbatt |
Yellow |
||
02 03 08 |
02 03 08 |
Circ.aperto oppure C.c. a Gnd Surriscaldamento Errore Generico |
||||||
EEC CRF MF3 |
40063 |
Bobina di accensione 3 |
01 02 03 08 |
01 02 03 08 |
C.c. a Vbatt Circ.aperto oppure C.c. a Gnd Surriscaldamento Errore Generico |
Yellow |
ECU Name |
SPN [Hex] |
Fault Component |
Description |
FMI [DEC] |
FMI [HEX] |
FMI Description |
Lamp status |
Comment |
EEC CRF MF3 |
40064 |
Bobina di accensione 4 |
01 02 03 08 |
01 02 03 08 |
C.c. a Vbatt Circ.aperto oppure C.c. a Gnd Surriscaldamento Errore Generico |
Yellow |
||
EEC CRF MF3 |
40065 |
Bobina di accensione 5 |
8 |
08 |
Errore Generico |
Yellow |
||
EEC CRF MF3 |
40066 |
Bobina di accensione 6 |
8 |
08 |
Errore Generico |
Yellow |
||
EEC CRF MF3 |
40088 |
Attuatore WASTEGATE |
01 02 04 |
01 02 04 |
C.c. a Vbatt C.c. a Gnd Circ. aperto |
Yellow |
||
EEC CRF MF3 |
40099 |
Linea CAN |
04 08 |
04 08 |
Segnale assente Bus Off |
Yellow |
||
EEC CRF MF3 |
40037 |
Potenziometro 1 Posizione Farfalla Motorizzata |
01 02 08 |
01 02 08 |
C.c. a Vbatt C.a. o c.c. a Gnd Avaria alimentazione sensore |
Yellow |
||
EEC CRF MF3 |
40038 |
Potenziometro 2 Posizione Farfalla Motorizzata |
01 02 08 |
01 02 08 |
C.c. a Vbatt C.a. o c.c. a Gnd Avaria alimentazione sensore |
Yellow |
||
EEC CRF MF3 |
40039 |
Coerenza Potenziometri Posizione Farfalla Motorizzata |
8 |
08 |
Errore Generico |
Yellow |
||
EEC CRF MF3 |
40085 |
Fault Contemporaneo Potenziometri Farfalla Motorizzata |
8 |
08 |
Errore Generico |
Red |
||
EEC CRF MF3 |
40028 |
Driver Farfalla Motorizzata |
01 02 03 04 05 06 08 |
01 02 03 04 05 06 08 |
C.c. a Vbatt C.c. a Gnd Surriscaldamento Circ. aperto Surriscaldamento (prewarning) Tensione Alimentazione Insufficiente Surriscaldamento (warning) |
Red |
||
EEC CRF MF3 |
40067 |
Farfalla Motorizzata — Allarme |
8 |
08 |
Farfalla bloccata |
Red |
||
EEC CRF MF3 |
40068 |
Farfalla Motorizzata — Warning |
1 |
01 |
Mancato ritorno in Limp Home |
Yellow |
||
EEC CRF MF3 |
40068 |
Farfalla Motorizzata — Warning |
8 |
08 |
Errore apprendimento minimo |
Yellow |
||
EEC CRF MF3 |
40069 |
Farfalla Motorizzata — PreWarning |
1 |
01 |
Mancato ritorno in Limp Home |
Yellow |
||
EEC CRF MF3 |
40069 |
Farfalla Motorizzata — PreWarning |
8 |
08 |
Errore apprendimento minimo |
Yellow |
||
EEC CRF MF3 |
40078 |
Condotto Aspirazione Aria |
01 02 |
01 02 |
Aria superiore alla stima Aria inferiore alla stima |
Yellow |
||
EEC CRF MF3 |
40079 |
Funzionalità ECU |
01 02 04 08 |
01 02 04 08 |
Errore di tipo M Errore di tipo C Errore di tipo S Errore generico |
Red |
||
EEC CRF MF3 |
40053 |
Riconoscimento Saturazione Autoadattatività |
01 02 |
01 02 |
Saturazione verso l’alto Saturazione verso il basso |
Yellow |
||
EEC CRF MF3 |
40049 |
Saturazione Persistente Autoadattatività |
8 |
08 |
Errore Generico |
Yellow |
||
EEC CRF MF3 |
40081 |
Riscaldatore sonda Lambda Postcatalizzatore |
01 02 |
01 02 |
C.c. a Vbatt C.c. a Gnd |
Yellow |
||
04 |
04 |
Circ. aperto |
||||||
EEC CRF MF3 |
40095 |
Catalizzatore |
8 |
08 |
Errore Generico |
Yellow |
||
EEC CRF MF3 |
40093 |
Sonda Lambda monte catalizzatore |
8 |
08 |
Errore Generico |
Yellow |
||
EEC CRF MF3 |
40094 |
Congruenza Lambda montevalle |
8 |
08 |
Errore Generico |
Yellow |
||
EEC CRF MF3 |
40096 |
Ripartizione Fuel System |
8 |
08 |
Errore ripartizione |
Yellow |
||
EEC CRF MF3 |
40097 |
Fuel System magro |
01 02 04 |
01 02 04 |
Guadagno iniett. Offset iniett. Saturazione |
Yellow |
||
EEC CRF MF3 |
40098 |
Fuel System ricco |
01 02 04 |
01 02 04 |
Guadagno iniett. Offset iniett. Saturazione |
Yellow |
||
EEC CRF MF3 |
40077 |
Comando Relè Elettroventola |
01 |
01 |
C.c. a Vbatt |
Yellow |
||
04 |
04 |
Circ. aperto |
||||||
EEC CRF MF3 |
40077 |
Comando Relè Elettroventola |
2 |
02 |
C.c. a Gnd |
Yellow |
||
VCM |
42701 |
CC set plus (Digital Input 5) |
02 03 |
02 03 |
02: data erratic, intermittend or incorrect (application (Eltrac) 03: voltage above normal or shorted high |
Yellow |
||
VCM |
42702 |
CC set minus (Digital Input 6) |
02 03 |
02 03 |
02: data erratic, intermittend or incorrect (application (Eltrac) 03: voltage above normal or shorted high |
Yellow |
||
VCM |
42703 |
CC resume (Digital Input 7) |
02 03 |
02 03 |
02: data erratic, intermittend or incorrect (application (Eltrac) 03: voltage above normal or shorted high |
Yellow |
||
VCM |
42704 |
CC off (Digital Input |
02 03 |
02 03 |
02: data erratic, intermittend or incorrect (application (Eltrac) 03: voltage above normal or shorted high |
Yellow |
||
VCM |
42705 |
CC internal / external (Digital Input 11) |
3 |
03 |
03: voltage above normal or shorted high |
Yellow |
||
VCM |
42706 |
ACC enable (Digital Input 25) |
03 |
03: voltage above normal or shorted high |
Yellow |
|||
04 |
04: voltage below or normal or shorted low |
|||||||
VCM |
42707 |
economy mode (Digital Input 13) |
3 |
03 |
03: voltage above normal or shorted high |
Yellow |
||
VCM |
42710 |
PTO2 (Digital Input 22) |
3 |
03 |
03: voltage above normal or shorted high |
Yellow |
||
VCM |
42711 |
PTO3 (Digital Input 23) |
3 |
03 |
03: voltage above normal or shorted high |
Yellow |
||
VCM |
42714 |
primary brake (Digital Input 1) |
02 04 |
02 04 |
02: data erratic, intermittend or incorrect (application Eltrac) 04: voltage below or normal or shorted low (device driver) |
Yellow |
||
VCM |
42715 |
secondary brake (Digital Input 2) |
02 04 |
02 04 |
02: data erratic, intermittend or incorrect (application (Eltrac) 04: voltage below or normal or shorted low (device driver) |
Yellow |
||
VCM |
42716 |
engine brake request (Digital Input 13) |
3 |
03 |
03: voltage above normal or shorted high |
Yellow |
||
VCM |
42717 |
engine brake mode 1 (Digital Input 14) |
3 |
03 |
03: voltage above normal or shorted high |
Yellow |
||
VCM |
42718 |
engine brake mode 2 (Digital Input 15) |
3 |
03 |
03: voltage above normal or shorted high |
Yellow |
||
VCM |
42719 |
parking brake (Digital Input 18) |
02 |
02: data erratic, intermittend or incorrect (application (Eltrac) |
Yellow |
|||
03 |
03: voltage above normal or shorted high |
|||||||
VCM |
42720 |
Fan control pressure switch 18 bar (Digital Input 27) |
03 04 |
03: voltage above normal or shorted high 04: voltage below or normal or shorted low |
Yellow |
|||
VCM |
42721 |
Fan control pressure switch 22 bar (Digital Input 28) |
03 04 |
03: voltage above normal or shorted high 04: voltage below or normal or shorted low |
Yellow |
|||
VCM |
42722 |
BB Neutral (High Side Output 1) |
03 04 05 |
03: voltage above normal or shorted high 04: voltage below or normal or shorted low 05: current below normal or open circuit |
Yellow |
|||
VCM |
42723 |
Output Single H Gear 1 / ACC Lamp (High Side Output 2) |
03 04 05 |
03: voltage above normal or shorted high 04: voltage below or normal or shorted low 05: current below normal or open circuit |
Yellow |
|||
VCM |
42726 |
BB Parking Brake (High Side Output 3) |
03 |
03: voltage above normal or shorted high |
Yellow |
|||
04 05 |
04: voltage below or normal or shorted low 05: current below normal or open circuit |
|||||||
VCM |
42727 |
Output Single H Gear 2 / ACC Buzzer (High Side Output 4) |
03 04 05 |
03: voltage above normal or shorted high 04: voltage below or normal or shorted low 05: current below normal or open circuit |
Yellow |
|||
VCM |
42728 |
BB Service Brake (High Side Output 5) |
03 04 05 |
03: voltage above normal or shorted high 04: voltage below or normal or shorted low 05: current below normal or open circuit |
Yellow |
|||
VCM |
42729 |
BB Programmable Threshold Speed (High Side Output 6) |
03 04 05 |
03: voltage above normal or shorted high 04: voltage below or normal or shorted low 05: current below normal or open circuit |
Yellow |
|||
VCM |
42731 |
Gear high / low request (Digital Input 12) |
02 |
02 |
02: data erratic, intermittend or incorrect (application (Eltrac) |
Yellow |
||
03 |
03 |
03: voltage above normal or shorted high |
||||||
VCM |
42732 |
clutch switch (Digital Input 9) |
02 03 |
02 03 |
02: data erratic, intermittend or incorrect (application (Eltrac) 03: voltage above normal or shorted high |
Yellow |
||
VCM |
42733 |
neutral switch (Digital Input 16) |
3 |
03 |
03: voltage above normal or shorted high |
Yellow |
||
VCM |
42734 |
D — automatic / manual (Digital Input 29) |
02 03 |
02: data erratic, intermittend or incorrect (application (Eltrac) 03: voltage above normal or shorted high |
Yellow |
|||
VCM |
42735 |
R — reverse (Digital Input 30) |
02 03 |
02: data erratic, intermittend or incorrect (application (Eltrac) 03: voltage above normal or shorted high |
Yellow |
|||
VCM |
42736 |
N — neutral shifting (Digital Input 31) |
02 03 |
02: data erratic, intermittend or incorrect (application (Eltrac) 03: voltage above normal or shorted high |
Yellow |
|||
VCM |
42737 |
gear up shift request (Digital Input 32) |
02 03 |
02: data erratic, intermittend or incorrect (application (Eltrac) 03: voltage above normal or shorted high |
Yellow |
|||
VCM |
42738 |
gear down shift request (Digital Input 33) |
02 03 |
02: data erratic, intermittend or incorrect (application (Eltrac) 03: voltage above normal or shorted high |
Yellow |
|||
VCM |
42739 |
Dm special manoeuvring (Digital Input 34) |
02 03 |
02: data erratic, intermittend or incorrect (application (Eltrac) 03: voltage above normal or shorted high |
Yellow |
|||
VCM |
42741 |
Frequency Input |
03 04 0A |
03: voltage above normal or shorted high 04: voltage below or normal or shorted low 0A: abnormal rate of change |
Yellow |
|||
VCM |
42746 |
cabin tilted (Digital Input 17) |
3 |
03 |
03: voltage above normal or shorted high |
Yellow |
||
VCM |
42747 |
engine remote start (Digital Input 19) |
02 03 |
02: data erratic, intermittend or incorrect (application (Eltrac) 03: voltage above normal or shorted high |
Yellow |
|||
VCM |
42748 |
engine remote stop (Digital Input 20) |
02 03 |
02: data erratic, intermittend or incorrect (application (Eltrac) 03: voltage above normal or shorted high |
Yellow |
|||
VCM |
42749 |
crank request (Digital Input 4) |
02 04 |
02 04 |
02: data erratic, intermittend or incorrect (application (Eltrac) 04: voltage below or normal or shorted low (device driver) |
Yellow |
||
VCM |
42750 |
Immobilizer LED (Low Side Output 3) |
03 04 05 |
03: voltage above normal or shorted high 04: voltage below or normal or shorted low 05: current below normal or open circuit |
Yellow |
|||
VCM |
42759 |
EP1 (development) |
01 02 03 04 05 |
01: data valid but below normal operation range 02: data erratic, intermittent or incorrect 03: voltage below normal or shorted high 04: voltage below normal or shorted low 05: voltage below normal or open circuit |
Yellow |
|||
VCM |
42760 |
Accelerator pedal correlation |
Pedal correlation first threshold Pedal correlation second threshold |
0D 0E |
0D: out of calibration 0E: special instruction |
Yellow |
||
VCM |
42764 |
TSC1 Handling |
Most severe level: positive engine brake torque control Most severe level: negative torque control detection Speed request over plausible windows Incoherent requests of fuelling and negative torque Moderately severe level: negative torque limit request |
00 01 0B 0C 12 |
00: data valid but above normal operation range 01: data valid but below normal operation range 0B: Root cause not known 0C: bad intelligent device or component 12: Data valid but below normal operational range |
Yellow |
||
VCM |
42765 |
Powertrain and Brake request Evaluation |
Active at least one error relative to TSC1_TE (44 ; 50 ; 38 ; 32 ; 20 ; 26 ; 14 ; 8 ; 2) |
0B |
0B: Root cause not known |
Yellow |
||
VCM |
42766 |
Powertrain and Brake request Evaluation |
Active at least one error relative to TSC1_AE (43 ; 49 ; 37 ; 31 ; 19 ; 25 ; 13 ; 7 ; 1) |
0B |
0B: Root cause not known |
Yellow |
||
VCM |
42767 |
Powertrain and Brake request Evaluation |
Active at least one error relative to TSC1_DE (45 ; 51 ; 39 ; 33 ; 21 ; 27 ; 15 ; 9 ; 3) |
0B |
0B: Root cause not known |
Yellow |
||
VCM |
42768 |
Powertrain and Brake request Evaluation |
Active at least one error relative to TSC1_PE (ICB) (47 ; 53 ; 41 ; 35 ; 23 ; 29 ; 17 ; 11 ; 5) |
0B |
0B: Root cause not known |
Yellow |
||
VCM |
42769 |
Powertrain and Brake request Evaluation |
Active at least one error relative to TSC1_PE (VDB) (48 ; 54 ; 42 ; 36 ; 24 ; 30 ; 18 ; 12 ; 6) |
0B |
0B: Root cause not known |
Yellow |
||
VCM |
42770 |
NORD Error |
wrong ratio between Vehicle speed and output shaft speed or bad EOL parameter |
0D |
0D: out of calibration |
Yellow |
||
VCM |
42771 |
NORD Error |
bad value inside the limitation MAPS or interpolation error |
12 |
12: Data valid but below normal operational range |
Yellow |
||
VCM |
42772 |
NORD Error |
wrong EOL parameters division by zero due to vehicle speed equal to 0Km/h |
2 |
02 |
02: data erratic, intermittend or incorrect |
Yellow |
|
VCM |
42773 |
NORD Error |
Software initializing a bad value on output. |
0B |
0B: Root cause not known |
Yellow |
ECU Name |
SPN [Hex] |
Fault Component |
Description |
FMI [DEC] |
FMI [HEX] |
FMI Description |
Lamp status |
Comment |
VCM |
42774 |
VIM — Vehicle information module |
— filtered MTCO vehicle speed greater than Brake speed of a certain EOL km/h threshold — filtered MTCO vehicle speed lower than Brake speed of a certain EOL km/h threshold — Totally missing vehicle speed — Missing TCO1 official information, but a recovery speed is available — MTCO vehicle speed greater than EOL thr Km/h |
00 01 02 0B 12 |
00: data valid but above normal operation range 01: data valid but below normal operation range 02: data erratic, intermittend or incorrect 0B: Root cause not known 12: Data valid but below normal operational range |
Yellow |
||
VCM |
42775 |
VIM — Vehicle information module |
— Engine speed totally missing — Engine speed missing but replaced |
02 0B |
02: data erratic, intermittend or incorrect 0B: Root cause not known |
Yellow |
||
— Engine speed over range |
13 |
13: received network data in error |
||||||
VCM |
42776 |
VIM — Vehicle information module |
— Engine temperature totally missing — Engine temperature missing but replaced — Engine temperature over range |
02 0B 13 |
02: data erratic, intermittend or incorrect 0B: Root cause not known 13: received network data in error |
Yellow |
||
VCM |
42777 |
(A)CC Output interface |
00 01 11 |
00: data valid but above normal operation range 01: data valid but below normal operation range — most severe level 11: Data valid but below normal operating range — least severe level |
Yellow |
|||
VCM |
42778 |
EM interface |
01 02 0C |
01: data valid but below normal operation range — most severe level 02: data erratic, intermittend or incorrect |
Yellow |
|||
10 11 |
0C: Bad intelligent device or component 10: Data valid but above normal operational range 11: Data valid but below normal operating range — least severe level |
|||||||
VCM |
42779 |
Low Idle Control Module |
Low idle speed setpoint is not within a valid range |
0B |
0B: failure mode not identifiable |
Yellow |
||
VCM |
42780 |
Cruise Control Buttons Interface Module |
0B |
0B: failure mode not identifiable |
Yellow |
|||
VCM |
42781 |
Cruise Control Buttons Interface Module |
0B 0C |
0B: Root cause not known 0C: Bad intelligent device or component |
Yellow |
|||
VCM |
42782 |
Power Take Off Module |
0B |
0B: failure mode not identifiable |
||||
VCM |
42783 |
Cruise Control Vehicle Speede Module |
0B |
0B: failure mode not identifiable |
||||
VCM |
42784 |
Gear Ratio calculation |
ncoherent value of the ratio of engine speed and tachograph output shaft speed |
0C |
0C: bad intelligent device or component |
Yellow |
||
VCM |
42785 |
Torque limit |
2 |
02 |
02: data erratic, intermittend or incorrect |
|||
VCM |
42788 |
Driveability |
Incoherent value of accelerator pedal and engine speed for MIN-MAX Incoherent value of engine speed for ALL SPEED |
02 0E |
02: data erratic, intermittend or incorrect 0E: special instructions |
Yellow |
||
VCM |
42789 |
Engine Brake Management |
TSC1_TER detection |
2 |
02 |
02: data erratic, intermittent, or incorrect |
||
VCM |
42790 |
Intarder Brake Management |
TSC1_ADR detection |
2 |
02 |
02: data erratic, intermittent, or incorrect |
||
VCM |
42791 |
Intarder Brake Management |
TSC1_CCDR detection |
2 |
02 |
02: data erratic, intermittent, or incorrect |
||
VCM |
42792 |
Powertrain and Brake request Evaluation |
One or more of internal error relative to TSC1_EME are active. |
11 |
0B |
0B: failure mode not identifiable |
||
VCM |
42793 |
VIM — Vehicle information module |
Brake light activation error. |
2 |
02 |
02: data erratic, intermittent, or incorrect |
Yellow |
|
VCM |
42794 |
Engine Brake Management |
TSC1_TXR detection |
2 |
02 |
02: data erratic, intermittent, or incorrect |
||
VCM |
42795 |
Engine Brake Management |
TSC1_AXR |
2 |
02 |
02: data erratic, intermittent, or incorrect |
||
VCM |
42796 |
Engine Brake Management |
TSC1_EMER detection |
2 |
02 |
02: data erratic, intermittent, or incorrect |
||
VCM |
42797 |
EU2LeverInterface |
Gear up request stucked |
02 |
02: data erratic, intermittent, or incorrect |
— |
||
Gear up request timeout |
09 |
09: abnormal update rate |
Yellow |
|||||
VCM |
42798 |
EU2LeverInterface |
Gear down request stucked Gear down request timeout |
02 09 |
02: data erratic, intermittent, or incorrect 09: abnormal update rate |
— Yellow |
||
VCM |
42799 |
EU2LeverInterface |
Neutral request stucked |
2 |
02 |
02: data erratic, intermittent, or incorrect |
Yellow |
|
VCM |
4270A |
adjustable speed limiter (Digital Input 10) |
3 |
03 |
03: voltage above normal or shorted high |
Yellow |
||
VCM |
4270B |
secondary speed limiter (Digital Input 3) |
02 04 |
02 04 |
02: data erratic, intermittend or incorrect (application (Eltrac) 04: voltage below or normal or shorted low (device driver) |
Yellow |
||
VCM |
4270F |
PTO1 (Digital Input 21) |
3 |
03 |
03: voltage above normal or shorted high |
Yellow |
||
VCM |
4271A |
engine brake mode (Digital Input 14) |
3 |
03 |
03: voltage above normal or shorted high |
Yellow |
||
VCM |
4272A |
BB Clutch Pedal (Low Side Output 2) |
03 04 05 |
03: voltage above normal or shorted high 04: voltage below or normal or shorted low 05: current below normal or open circuit |
Yellow |
|||
VCM |
4273A |
Rm special manoeuvring (Digital Input 35) |
02 03 |
02: data erratic, intermittend or incorrect (application (Eltrac) 03: voltage above normal or shorted high |
Yellow |
|||
VCM |
4273B |
Clutch switch 2 (Digital Input 26) |
02 03 04 |
02: data erratic, intermittend or incorrect (application (Eltrac) 03: voltage above normal or shorted high 04: voltage below or normal or shorted low |
Yellow |
|||
VCM |
4273C |
Low Idle (Digital Input 24) |
Short 5V Short 24V Short low Switch does not switches Switching point outside specification Switching point valid but slight outside specification |
02 03 04 05 08 0D |
02: data erratic, intermittend or incorrect 03: voltage above normal or shorted high 04: voltage below or normal or shorted low 05: current below normal or open circuit 08: abnormal frequency, pulse width or period 0D: out of calibration |
Yellow Yellow Yellow Yellow Yellow — |
||
VCM |
4273D |
accelerator pedal (Analog Input 1) |
Analog value valid but slight too high |
00 |
00: data valid but above normal operation range |
— |
||
Analog value valid but slight too low Analog value too high Short 24V Short low Short 5V Analog value too low |
01 02 03 04 0D 0E |
01: data valid but below normal operation range 02: data erratic, intermittend or incorrect 03: voltage above normal or shorted high 04: voltage below or normal or shorted low 0D: out of calibration 0E: special instructions |
— Yellow Yellow Yellow Yellow Yellow |
|||||
VCM |
4273E |
Acc. Pedal Power Supply (5 V supply) |
02 04 |
02: data erratic, intermittend or incorrect 04: voltage below or normal or shorted low |
Yellow |
|||
VCM |
4274A |
crank relay (High Side Output 7) |
03 04 05 |
03: voltage above normal or shorted high 04: voltage below or normal or shorted low 05: current below normal or open circuit |
Yellow |
|||
VCM |
4274B |
crank relay (Low Side Output 1) |
External crank relay activation |
03 |
03: voltage above normal or shorted high |
Yellow |
||
04 05 06 |
04: voltage below or normal or shorted low 05: current below normal or open circuit 06: current above normal or grounded circuit |
Yellow Yellow Red |
||||||
VCM |
4275A |
ACC Sensor 1 |
Sensor comunication error Sensor continuosly not available Sensor temperature not available |
0B 0C 0D |
0B: failure mode not identifiable 0C: bad intelligent device or component 0D: out of calibration |
Yellow |
||
VCM |
4275B |
ACC distance selector input (Analog Input 2) |
03 04 |
03: voltage above normal or shorted high 04: voltage below or normal or shorted low |
Yellow |
|||
VCM |
4275C |
ACC dist. Sel. / Pedal sensor 2 supply (5 V supply) |
Supply out of range Supply short high Supply short low |
02 03 04 |
02: data erratic, intermittend or incorrect 03: voltage above normal or shorted high 04: voltage below or normal or shorted low |
Yellow |
||
VCM |
4275D |
ACC Parameter |
Flash parameter not correct |
0D |
0D: out of calibration |
Yellow |
||
VCM |
4275E |
ACC Sensor 2 |
Sensor dirty |
0E |
0E: special instructions |
Yellow |
||
VCM |
4275F |
Accelerator pedal sensor 2 (Analog Input 3) |
Analog value valid but slight too high Analog value valid but slight too low Analog value too high Short 24V Short low Short 5V Analog value too low |
00 01 02 03 04 0D 0E |
00: analog value valid but slight too high 01: analog value valid but slight too low 02: analog value too high 03: short 24V 04: short low 0D: short 5V 0E: analog value too low |
— — Yellow Yellow Yellow Yellow Yellow |
||
VCM |
4276A |
Powertrain and Brake request Evaluation |
Active at least one error relative to TSC1__CCE (46 ; 52 ; 40 ; 34 ; 22 ; 28 ; 16 ; 10 ; 4) |
0B |
0B: Root cause not known |
Yellow |
||
VCM |
4276F |
NORD Error |
wrong link between Current gear and gear number rangex (x=1..5) |
13 |
13: received network data in error |
Yellow |
||
VCM |
4277A |
High Idle Control Module |
High idle speed setpoint is not within a valid range |
0B |
0B: failure mode not identifiable |
Yellow |
||
VCM |
4277B |
Intermediate Speed Control Module |
Itermediate speed control setpoint/limit is not within a valid range |
0B |
0B: failure mode not identifiable |
Yellow |
||
VCM |
4277C |
Cruise Control Buttons Interface Module |
2 |
02 |
02: data erratic, intermittend or incorrect |
|||
VCM |
4277D |
Cruise Control Buttons Interface Module |
02 0B 0C |
02: data erratic, intermittend or incorrect 0B: Root cause not known 0C: Bad intelligent device or component |
Yellow Yellow — |
|||
VCM |
4277E |
Cruise Control Buttons Interface Module |
2 |
02 |
02: data erratic, intermittend or incorrect |
|||
VCM |
4277F |
Cruise Control Buttons Interface Module |
2 |
02 |
02: data erratic, intermittend or incorrect |
Yellow |
||
VCM |
4278A |
Engine Brake Management |
TSC1_AER detection |
2 |
02 |
02: data erratic, intermittent, or incorrect |
||
VCM |
4278B |
Engine Brake Management |
TSC1_DER detection |
2 |
02 |
02: data erratic, intermittent, or incorrect |
||
VCM |
4278C |
Engine Brake Management |
TSC1_PER on VDB detection |
2 |
02 |
02: data erratic, intermittent, or incorrect |
||
VCM |
4278D |
Engine Brake Management |
TSC1_PER on ICB detection |
2 |
02 |
02: data erratic, intermittent, or incorrect |
||
VCM |
4278E |
Engine Brake Management |
TSC1_CCER detection |
2 |
02 |
02: data erratic, intermittent, or incorrect |
||
VCM |
4278F |
Engine Brake Management |
When VCM receives TSC1_PER both on ICB and VDB |
2 |
02 |
02: data erratic, intermittent, or incorrect |
||
VCM |
4279A |
EU2LeverInterface |
Drive Forward / Drive Forward manoeuvring: Button stucked Button not plausible |
02 0C |
02: data erratic, intermittent, or incorrect 0C: bad intelligent device or component |
Yellow |
||
VCM |
4279B |
EU2LeverInterface |
Drive Reverse / Drive Reverse manoeuvring: Button stucked Button not plausible |
02 0C |
02: data erratic, intermittent, or incorrect 0C: bad intelligent device or component |
Yellow |
||
VCM |
4279C |
Service Brake Eval |
Primary brake sw/secondary brake sw not plausible |
0C |
0C: bad intelligent device or component |
Red |
||
VCM |
4279D |
Driver Intarder Brake |
Intarder brake lever not plausible |
0C |
0C: bad intelligent device or component |
Yellow |
||
VCM |
4279E |
Engine Fan |
switch 18 and 22 not plausible |
0C |
0C: bad intelligent device or component |
Yellow |
||
VCM |
4279F |
Driver Engine Brake |
Plausibility check on the Engine brake lever |
0C |
0C: bad intelligent device or component |
Yellow |
||
VCM |
427B4 |
Immobilizer1 |
Transponder programming not possible |
02 |
02: data erratic, intermittend or incorrect |
Yellow |
||
Transponder programming not possible Different pin source within keyset IDE has been read twice or is equal 0 Max number of keys exceeded |
0B 0C 0D 0E |
0B: failure mode not identifiable 0C: bad intelligent device or component 0D: out of calibration 0E: special instructions |
||||||
VCM |
427B5 |
Immobilizer2 |
Ignition not switched off in time Unknown IDE |
02 0B |
02: data erratic, intermittend or incorrect 0B: failure mode not identifiable |
Yellow |
||
VCM |
427B6 |
Immobilizer3 |
No communication to ECM Unknown ECM No immobilizer function in ECM |
0C 0D 0E |
0C: bad intelligent device or component 0D: out of calibration 0E: special instructions |
Yellow |
||
VCM |
427B7 |
Immobilizer4 |
VCM in plant mode ECM in plant mode and learning already completed |
02 0B |
02: data erratic, intermittend or incorrect 0B: failure mode not identifiable |
Yellow |
||
VCM |
427B8 |
Immobilizer in plant mode |
VCM in plant mode and key learning active |
2 |
02 |
02: data erratic, intermittend or incorrect |
Yellow |
|
VCM |
427B9 |
Immobilizer5 |
Bit error in transponder response Antenna hardware error Internal operation error No transponder response |
02 07 0B 0C |
02: data erratic, intermittend or incorrect 07: mechanicial system not responding properly 0B: failure mode not identifiable 0C: bad intelligent device or component |
Yellow |
||
VCM |
427BA |
auxiliary use 1 |
2 |
02 |
02: data erratic, intermittend or incorrect |
Yellow |
||
VCM |
427BB |
auxiliary use 2 |
2 |
02 |
02: data erratic, intermittend or incorrect |
Yellow |
||
VCM |
427BC |
auxiliary use 3 |
2 |
02 |
02: data erratic, intermittend or incorrect |
Yellow |
||
VCM |
427BD |
auxiliary use 4 |
2 |
02 |
02: data erratic, intermittend or incorrect |
Red |
||
VCM |
427BE |
auxiliary use 5 |
2 |
02 |
02: data erratic, intermittend or incorrect |
Red |
||
VCM |
427C0 |
Vehicle Data Bus (instrument cluster) |
not supported: ServiceInfo Timeout (VDB) ACC2 timeout (VDB) DM1_IC timeout (VDB) |
01 02 03 |
01: data valid but below normal operation range 02: data erratic, intermittend or incorrect 03: voltage above normal or shorted high |
Yellow — — |
||
IC2BC timeout (VDB) |
04 |
04: voltage below or normal or shorted low |
||||||
VCM |
427C8 |
Vehicle Data Bus |
VDB limitation VDB bus off |
0B 13 |
0B: abnormal rate of change 13: received network data in error |
— Yellow |
ECU Name |
SPN [Hex] |
Fault Component |
Description |
FMI [DEC] |
FMI [HEX] |
FMI Description |
Lamp status |
Comment |
VCM |
427C9 |
Vehicle Data Bus (brake controller) |
EBC1 timeout EBC2 timeout TSC1_AE timeout TSC1_AER timeout TSC1_ADR timeout EBC5 timeout VDC1 timeout VDC2 timeout CVW timeout |
01 02 03 04 05 06 07 08 09 |
01: Abnormal update rate 02: Abnormal update rate 03: Abnormal update rate 04: Abnormal update rate 05: Abnormal update rate 06: Abnormal update rate 07: Abnormal update rate 08: Abnormal update rate 09: Abnormal update rate |
Yellow Yellow Yellow Yellow — — — — — |
||
HRW timeout TC1_EBS timeout TSC1_AXR timeout |
0A 0B 0C |
0A: Abnormal update rate 0B: Abnormal update rate 0C: Abnormal update rate |
— — Yellow |
|||||
VCM |
427CA |
Vehicle Data Bus (transmission controller) |
ETC1 timeout (VDB) ETC2 timeout (VDB) TSC1_TE timeout (VDB) TSC1_TER timeout (VDB) ETC8 timeout (VDB) TSC1_TXR timeout (VDB) ETC7 timeout (VDB) not supported: ETC5 timeout (VDB) TC_BC timeout (VDB) |
01 02 03 04 05 06 07 08 09 |
01: Abnormal update rate 02: Abnormal update rate 03: Abnormal update rate 04: Abnormal update rate 05: Abnormal update rate 06: Abnormal update rate 07: Abnormal update rate 08: Abnormal update rate 09: Abnormal update rate |
Yellow Yellow Yellow Yellow — Yellow — — — |
||
CVW_GB timeout (VDB) |
0A |
0A: Abnormal update rate |
— |
|||||
VCM |
427CB |
Vehicle Data Bus (body controller) |
not supported: AIR1 timeout (VDB) TSC1_PEV timeout (VDB) TSC1_PERV timeout (VDB) TSC1_EME timeout (VDB) TSC1_EMER timeout (VDB) BC2EDC timeout (VDB) AMB_COND_IBC timeout (VDB) BCAO1 timeout (VDB) BCAO2 timeout (VDB) BCAO3 timeout (VDB) DASH_DISPLAY timeout (VDB) |
01 02 03 04 05 06 07 08 09 0B 0A |
01: Abnormal update rate 02: Abnormal update rate 03: Abnormal update rate 04: Abnormal update rate 05: Abnormal update rate 06: Abnormal update rate 07: Abnormal update rate 08: Abnormal update rate 09: Abnormal update rate 0B: abnormal update rate 0A: abnormal update rate |
— — — — — Yellow — Yellow — — — |
||
not supported: Other Body controller timeout (VDB) |
13 |
13: abnormal update rate |
— |
|||||
VCM |
427CC |
Vehicle Data Bus (driveline retarder) |
ERC1_DR timeout (VDB) TSC1_DE timeout (VDB) TSC1_DER timeout (VDB) BAM_DR / MPM_DR timeout (VDB) |
01 02 03 04 |
01: Abnormal update rate 02: Abnormal update rate 03: Abnormal update rate 04: Abnormal update rate |
Yellow — — — |
||
VCM |
427CD |
Vehicle Data Bus (tachograph) |
TCO1 timeout (VDB) VHDR timeout (VDB) Time Date timeout (VDB) |
01 02 03 |
01: Abnormal update rate 02: Abnormal update rate 03: Abnormal update rate |
Yellow — — |
||
VCM |
427CE |
Vehicle Data Bus (ACC sensor) |
ACC_SI timeout (VDB) DM1_ACCSens timeout (VDB) |
01 02 |
01: Abnormal update rate 02: Abnormal update rate |
Yellow |
||
VCM |
427CF |
Vehicle Data Bus (expansion module) |
EM2VCM timeout (VDB) TC1_EM timeout (VDB) |
01 02 |
01: Abnormal update rate 02: Abnormal update rate |
Yellow — |
||
EM_CMD timeout (VDB) TSC1_PE timeout (VDB) TSC1_PER timeout (VDB) PTO_Status timeout (VDB) EM2BC timeout (VDB) |
03 04 05 06 07 |
03: Abnormal update rate 04: Abnormal update rate 05: Abnormal update rate 06: Abnormal update rate 07: Abnormal update rate |
— — — Yellow — |
|||||
VCM |
427D0 |
Vehicle Data Bus (steering wheel interface) |
SWI2BC timeout (VDB) |
09 |
09: Abnormal update rate |
Yellow |
||
VCM |
427D1 |
Vehicle Data Bus (suspension) |
not supported: ASC1_A timeout (VDB) not supported: ASC3_A timeout (VDB) not supported: ASC4_A timeout (VDB) not supported: Vehicle_Weight timeout (VDB) |
06 07 08 09 |
06: Abnormal update rate 07: Abnormal update rate 08: Abnormal update rate 09: Abnormal update rate |
|||
VCM |
427D2 |
Engine Control Bus |
ECB bus off |
13 |
13: received network data in error |
Yellow |
||
ECB limitation |
0A |
0A: abnormal rate of change |
||||||
VCM |
427D3 |
Engine Control Bus (engine) |
EEC1 timeout (ECB) EEC2 timeout (ECB) EEC3 timeout (ECB) ENG_TEMP timeout (ECB) AMB_COND_E timeout (ECB) INLET_COND timeout (ECB) EDC2BC timeout (ECB) Eng_Fld_Lev_Press timeout (ECB) ELT_POWER timeout (ECB) Shutdown timeout (ECB) Fuel_Economy timeout (ECB) |
01 02 03 04 05 06 07 08 09 0A 0B |
01: Abnormal update rate 02: Abnormal update rate 03: Abnormal update rate 04: Abnormal update rate 05: Abnormal update rate 06: Abnormal update rate 07: Abnormal update rate 08: Abnormal update rate 09: Abnormal update rate 0A: abnormal update rate 0B: Abnormal update rate |
Yellow Yellow — Yellow — Yellow Yellow — Yellow — — |
||
Fuel_Cons timeout (ECB) not supported: Eng_Hours_Rev timeout (ECB) BAM_Eng_Conf / MPM_Eng_Conf timeout (ECB) FAN_Drive timeout (ECB) |
0C 0D 0E 0F |
0C: Abnormal update rate 0D: Abnormal update rate 0E: Abnormal update rate 0F: Abnormal update rate |
— — — Yellow |
|||||
VCM |
427D4 |
Engine Control Bus (engine retarder) |
BAM_ret_conf / MPM_ret_conf timeout (ECB) ERC1_ER timeout (ECB) |
01 02 |
01: Abnormal update rate 02: Abnormal update rate |
Yellow |
||
VCM |
427D5 |
Engine Control Bus (exhaust emission controller — UDS) |
SCR_status2 timeout (ECB) |
09 |
09: Abnormal update rate |
Yellow |
||
VCM |
427DC |
Instrument Cluster Bus |
ICB bus off ICB limitation |
13 0A |
13: received network data in error 0A: abnormal rate of change |
Yellow |
||
VCM |
427DD |
Instrument Cluster Bus (body computer) |
BC_Status1 timeout (ICB) BC_Status2 timeout (ICB) |
01 02 |
01: Abnormal update rate 02: Abnormal update rate |
Yellow — |
||
BC_Status3 timeout (ICB) RF_Status1 timeout (ICB) BC2IC timeout (ICB) PTO_Status timeout (ICB) FF_Status1 timeout (ICB) Trip_Total_Fuel timeout (ICB) TCO1 timeout (ICB) |
03 04 05 06 07 08 09 |
03: Abnormal update rate 04: Abnormal update rate 05: Abnormal update rate 06: Abnormal update rate 07: Abnormal update rate 08: Abnormal update rate 09: Abnormal update rate |
— — — Yellow — — — |
|||||
VCM |
427DE |
Instrument Cluster Bus (steering wheel interface) |
SWI2BC timeout (ICB) not supported: SWI2IC timeout (ICB) |
01 02 |
01: Abnormal update rate 02: Abnormal update rate |
|||
VCM |
427DF |
Instrument Cluster Bus (expansion module) |
not supported: EM2VCM timeout (ICB) not supported: TC1_EM timeout (ICB) not supported: EM_CMD timeout (ICB) |
01 02 03 |
01: Abnormal update rate 02: Abnormal update rate 03: Abnormal update rate |
Yellow — — |
||
not supported: TSC1_PE timeout (ICB) not supported: TSC1_PER timeout (ICB) not supported: EM2BC timeout (ICB) not supported: CTL timeout (ICB) not supported: ASC2 timeout (ICB) |
04 05 06 07 08 |
04: Abnormal update rate 05: Abnormal update rate 06: Abnormal update rate 07: Abnormal update rate 08: Abnormal update rate |
— — — — — |
|||||
VCM |
427E2 |
Instrument Cluster Bus (instrument cluster) |
IC2BC timeout (ICB) ACC2 timeout (ICB) |
01 02 |
01: Abnormal update rate 02: Abnormal update rate |
|||
VCM |
427E3 |
Instrument Cluster Bus (ACC sensor) |
ACC_SI timeout (ICB) DM1_ACCSens timeout (ICB) |
01 02 |
01: Abnormal update rate 02: Abnormal update rate |
Yellow |
||
VCM |
427E6 |
FMS Bus |
FMS bus off FMS limitation |
13 0A |
13: received network data in error 0A: abnormal rate of change |
Yellow |
||
VCM |
427E7 |
FMS Bus (EP1) |
FLEX0 time out (FMS) |
01 |
01: Abnormal update rate |
Yellow |
||
FLEX1 time out (FMS) FLEX2 time out (FMS) FLEX3 time out (FMS) FLEX4 time out (FMS) FLEX5 time out (FMS) FLEX6 time out (FMS) FLEX7 time out (FMS) XFLEX0 time out (FMS) XFLEX1 time out (FMS) |
02 03 04 05 06 07 08 09 0A |
02: Abnormal update rate 03: Abnormal update rate 04: Abnormal update rate 05: Abnormal update rate 06: Abnormal update rate 07: Abnormal update rate 08: Abnormal update rate 09: Abnormal update rate 0A: Abnormal update rate |
||||||
VCM |
427F0 |
Power Supply Key 15 |
Key 15 transition resistence Key 15 active and CAN status inactive Key 15 inactive and CAN status active |
02 03 04 |
02: data erratic, intermittend or incorrect 03: voltage above normal or shorted high 04: voltage below or normal or shorted low |
Yellow |
||
VCM |
427F1 |
Power Supply Key 30 |
00 01 |
00: data valid but above normal operation range 01: data valid but below normal operation range |
||||
VCM |
427F2 |
Internal Failure 1 (Runcontrol) |
External rucontrol Internal rucontrol Watchdog timeout |
0C 0D 0E |
0C: bad intelligent device or component 0D: out of calibration 0E: special instructions |
Red |
||
VCM |
427F3 |
Internal Failure 6 (Rx Lookuptable) |
CAN Lookuptable overflow |
0D |
0D: out of calibration |
Red |
||
VCM |
427F4 |
Internal Failure 7 (CPU overlooad) |
CPU overload |
2 |
02 |
02: data erratic, intermittend or incorrect |
Yellow |
|
VCM |
427FB |
Internal Failure 3 (RAM / ROM) |
RAM failuire ROM failure |
02 0D |
02: data erratic, intermittend or incorrect 0D: out of calibration |
Red |
||
VCM |
427FD |
Internal Failure 2 (EEPROM) |
Checksum parameter range Checksum environment data Checksum engine values |
02 0B 0C |
02: data erratic, intermittend or incorrect 0B: failure mode not identifiable 0C: bad intelligent device or component |
— — — |
||
Checksum immobilizer range Checksum production data Checksum runtime counter |
0D 0E 1F |
0D: out of calibration 0E: special instructions 1F: not available or condition exists |
Yellow Yellow Yellow |
|||||
VCM |
427FE |
Internal Failure 4 (Controller) |
Parameter version wrong Operating system failure Software trap Controller failure |
0B 0C 0D 0E |
0B: failure mode not identifiable 0C: bad intelligent device or component 0D: out of calibration 0E: special instructions |
Red |
||
VCM |
427FF |
Internal Failure 5 (Bootloader) |
Flash parameter failure Flash program failure |
0C 0D |
0C: bad intelligent device or component 0D: out of calibration |
Red |
||
EM_SH |
047225 |
Pin A07 — Singel-H Buzzer Output |
High Side switch: — S.C. to Vbat detected in Off condition — S.C. to Gnd / Overload detected in On condition — Open Load detected in Off condition (fault active below 20uA÷2mA) Open Circuit and Short to Battery flags set together by EM IL, FMI 5 used for both. |
4 5 |
04 05 |
Voltage below normal, or shorted to low source Current below normal or open circuit (also in case of Voltage above normal, or shorted to high source) |
Yellow |
|
EM_SH |
047226 |
Pin D28 — Gate Interlock Solenoid valve |
Low Side switch: — S.C. to Vbat / Overload detected in On condition — S.C. to Gnd detected in Off condition — Open Load detected in Off condition (fault active below 20uA÷2mA) Open Circuit and Short to Ground flags set together by EM IL, FMI 5 used for both. |
3 5 |
03 05 |
Voltage above normal, or shorted to high source Current below normal or open circuit (also in case of Voltage below normal, or shorted to low source) |
Red |
|
EM_SH |
047220 |
Pin D05 — Low Range Solenoid valve |
Low Side switch: — S.C. to Vbat / Overload detected in On condition — S.C. to Gnd detected in Off condition — Open Load detected in Off condition (fault active below 20uA÷2mA) Open Circuit and Short to Ground flags set together by EM IL, FMI 5 used for both. |
3 5 |
03 05 |
Voltage above normal, or shorted to high source Current below normal or open circuit (also in case of Voltage below normal, or shorted to low source) |
Red |
ECU Name |
SPN [Hex] |
Fault Component |
Description |
FMI [DEC] |
FMI [HEX] |
FMI Description |
Lamp status |
Comment |
|
EM_SH |
047221 |
Pin D04 — High Range Solenoid valve |
Low Side switch: — S.C. to Vbat / Overload detected in On condition — S.C. to Gnd detected in Off condition — Open Load detected in Off condition (fault active below 20uA÷2mA) Open Circuit and Short to Ground flags set together by EM IL, FMI 5 used for both. |
3 5 |
03 05 |
Voltage above normal, or shorted to high source Current below normal or open circuit (also in case of Voltage below normal, or shorted to low source) |
Red |
||
EM_SH |
47222 |
Pin A01 — Safety |
High Side switch: — S.C. to Vbat detected in Off condition — S.C. to Gnd / Overload detected in On condition — Open Load detected in Off condition (fault active below 20uA÷2mA) |
4 5 |
04 05 |
Voltage below normal, or shorted to low source Current below normal or open circuit (also in case of Voltage above normal, or shorted to high source) |
Red |
||
EM_SH |
47223 |
Pin A04 — Splitter H |
High Side switch: — S.C. to Gnd / Overload detected in On condition |
4 |
04 |
Voltage below normal, or shorted to low source |
Red |
||
EM_SH |
47224 |
Pin A06 — Splitter L |
High Side switch: — S.C. to Gnd / Overload detected in On condition |
4 |
04 |
Voltage below normal, or shorted to low source |
Red |
||
EM_SH |
0472E1 |
Range Preselection switches |
Plausibility error: «Range Presel Low Sw» and «Range Presel High Sw» having the same value |
2 |
02 |
Plausibility error |
Red |
||
EM_SH |
0472E2 |
Clutch sensors |
Plausibility error: «Clutch Open Switch» (alias «2nd Clutch Switch«) closed while «CCVS-Clutch Switch» open. Healed when «Clutch Open Switch» = open. |
2 |
02 |
Plausibility error |
Red |
||
UDS DCU15 |
003D13 |
Battery voltage sensing (electrical) |
013_ABSI |
3 4 |
03 04 |
signal high signal low |
FnR_DNOx2_p910vC241 |
||
0 1 |
00 01 |
signal above high error threshold signal below low error threshold |
|||||||
UDS DCU15 |
003D13 |
Battery voltage sensing (electrical) |
013ABSI |
3 4 |
03 04 |
signal high signal low |
MIL |
FnR_DNOx2_V74 Long Term failure |
|
UDS DCU15 |
003D14 |
Temperature sensor after catalyst (electrical) |
014_ACTD2 |
0 1 |
00 01 |
signal high signal low |
|||
UDS DCU15 |
003D15 |
Temperature sensor after catalyst (electrical) |
015_ACTD |
3 4 |
03 04 |
signal high signal low |
MIL |
Power Reduction Long Term failure |
|
UDS DCU15 |
003D16 |
Temperature sensor before catalyst (electrical) |
016_ACTU |
3 4 0 1 |
03 04 00 01 |
signal high signal low signal above high error threshold signal below low error threshold |
FnR_DNOx2_p910vC241 |
||
UDS DCU15 |
003D16 |
Temperature sensor before catalyst (electrica |
016ACTU |
3 4 |
03 04 |
signal high signal low |
MIL |
FnR_DNOx2_V74 Long Term failure |
|
UDS DCU15 |
003D17 |
Sensor supply 1 (5V internal; for UREA level sensor) |
017_DSS1 |
3 4 |
03 04 |
Supply Voltage too high Supply voltage too low |
|||
UDS DCU15 |
003D18 |
Sensor supply 2 (5V internal; for UREA pressure sensors) |
018_DSS2 |
3 4 |
03 04 |
Supply Voltage too high Supply voltage too low |
MIL |
||
UDS DCU15 |
003D19 |
UREA pressure sensor in box (electrical) |
019_AUPS |
3 4 2 |
03 04 02 |
signal high signal low supply voltage error |
MIL |
Power Reduction Long Term failure |
|
UDS DCU15 |
003D1A |
UREA Temperature sensor in box (electrical) |
01A_AUTB |
3 4 0 |
03 04 00 |
signal high signal low signal above high error threshold |
FnR_DNOx2_p910vC241 |
||
1 |
01 |
signal below low error threshold |
|||||||
UDS DCU15 |
003D1A |
UREA Temperature sensor in box (electrical) |
01AAUTB |
3 4 |
03 04 |
high signal signal low |
FnR_DNOx2_V74 |
||
UDS DCU15 |
003D1B |
UREA pressure evaluation(above and below limit) |
01B_AUPS2 |
0 1 |
00 01 |
diagnostic value above high limit diagnostic value below low limit |
|||
UDS DCU15 |
003D21 |
Voltage supply internal heaters 1 (UB1) electrical |
021_ABV1 |
3 5 |
03 05 |
Short to bat at UB1 with Key 15 off Open circuit to UB1 |
FnR_DNOx2_p910vC241 |
||
UDS DCU15 |
003D21 |
Voltage supply internal heaters 1 (UB1) electrical |
021ABV1 |
6 5 |
06 05 |
Short to bat at UB1 with Key 15 off Open circuit to UB1 |
MIL |
FnR_DNOx2_V74 Long Term failure |
|
UDS DCU15 |
003D22 |
Voltage supply 2 — tube heaters (UB2) electrical |
022_ABV2 |
3 5 4 |
03 05 04 |
Short to bat at UB2 with Key 15 off Open circuit to UB2 Short circuit to Ground UB2 |
FnR_DNOx2_p910vC241 |
||
UDS DCU15 |
003D22 |
Voltage supply 2 — tube heaters (UB2) electrical |
022ABV2 |
3 4 5 |
03 04 05 |
Short to bat at UB2 with Key 15 off Open circuit to UB2 Short circuit to Ground UB2 |
FnR_DNOx2_V74 |
||
UDS DCU15 |
003D23 |
Voltage supply 3 — Coolant control valve and reverting valve (UB3) electrical |
023_ABV3 |
3 5 4 |
03 05 04 |
Short to bat at UB3 with Key 15 off Open circuit to UB3 Short circuit to Ground UB3 |
FnR_DNOx2_p910vC241 |
||
UDS DCU15 |
003D23 |
Voltage supply 3 — Coolant control valve and reverting valve (UB3) electrical |
023ABV3 |
3 4 5 |
03 04 05 |
Short to bat at UB3 with Key 15 off Open circuit to UB3 Short circuit to Ground UB3 |
FnR_DNOx2_V74 |
||
UDS DCU15 |
003D24 |
Monitoring VDD11/VDD25 voltage — Dosing valve/Pump motor |
024_AV11 |
3 4 0 |
03 04 00 |
supply voltage VD11 high supply voltage VD11 low supply voltage VD25 high |
FnR_DNOx2_p910vC241 |
||
1 |
01 |
supply voltage VD25 low |
|||||||
UDS DCU15 |
003D24 |
Monitoring VDD11 voltage — Dosing valve |
024AV11 |
4 3 |
04 03 |
supply voltage high supply voltage low |
FnR_DNOx2_V74 |
||
UDS DCU15 |
003D31 |
UREA level sensor (electrical) |
031AULS |
3 4 2 |
03 04 02 |
signal high signal low supply voltage error |
MIL |
FnR_DNOx2_V74 |
|
UDS DCU15 |
003D32 |
UREA Temperature sensor in Tank (electrical) |
032AUTT |
3 4 |
03 04 |
signal high signal low |
FnR_DNOx2_V74 |
||
UDS DCU15 |
003D34 |
UREA Quality Sensor |
034EUQS |
5 6 7 2 |
05 06 07 02 |
open wire short circuit not plausible temperature outside operation range |
FnR_DNOx2_V74 |
||
0 1 12 |
00 01 0C |
concentration higher than specified value concentration is less than specified value empty or partially filled sensor |
|||||||
UDS DCU15 |
003D35 |
NOx sensor (self monitoring of sensor / only CAN message) |
035NOXS |
4 3 2 |
04 03 02 |
Nox sensor Short circuit NOx Sensor Open circuit Other Nox sensor error |
FnR_DNOx2_V74 |
||
UDS DCU15 |
003D41 |
Diagnostic lamp (electrical) |
041_PDIA |
6 3 5 |
06 03 05 |
short circuit to batt + open circuit or short to ground Open load |
FnR_DNOx2_p910vC241 |
||
UDS DCU15 |
003D41 |
Diagnostic lamp (electrical) |
041PDIA |
4 3 5 |
04 03 05 |
short circuit to batt + open circuit or short to ground Open load |
FnR_DNOx2_V74 |
||
UDS DCU15 |
003D52 |
Dosing Valve (electrical) |
052_PUDV |
6 3 5 |
06 03 05 |
short circuite to ground short circuit to batt + open load Dosing valve permanent «ON» (detection via fast decay) |
FnR_DNOx2_p910vC241 |
||
UDS DCU15 |
003D52 |
Dosing Valve (electrical) |
052PUDV |
4 3 5 7 |
04 03 05 07 |
short circuite to ground short circuit to batt + open load Dosing valve permanent «ON» (detection via fast decay) |
MIL |
FnR_DNOx2_V74 Long Term failure |
|
UDS DCU15 |
003D53 |
UREA Pump speed |
053_PUMP |
7 8 2 12 |
07 08 02 0C |
pump motor blocked pump overspeed pump motor unplugged Hall sensors defect |
MIL |
Power Reduction Long Term failure |
|
UDS DCU15 |
003D55 |
Cooling control valve short circuit to UBat or open load |
055_PCCV |
3 5 |
03 05 |
short circuit to battery Open load |
FnR_DNOx2_p910vC241 |
||
UDS DCU15 |
003D55 |
Cooling control valve short circuit to UBat or open load |
055PCCV |
6 5 |
06 05 |
short circuit to battery Open load |
FnR_DNOx2_V74 Power Reduction |
||
UDS DCU15 |
003D56 |
Cooling control valve short circuit to ground |
056_PCCV2 |
6 |
06 |
short circuit to ground |
Power Reduction |
||
UDS DCU15 |
003D57 |
Reverting valve (4-2way valve?) electrically |
057_PRVV |
6 3 5 |
06 03 05 |
Short circuit to ground Short circuit to battery Open load |
FnR_DNOx2_p910vC241 |
||
UDS DCU15 |
003D57 |
Reverting valve (4-2way valve?) electrically |
057PRVV |
4 3 5 |
04 03 05 |
Short circuit to ground Short circuit to battery Open load |
FnR_DNOx2_V74 |
||
UDS DCU15 |
003D58 |
Valve Blocked Closed Test failed |
058SUDV |
12 6 5 |
0C 06 05 |
dosing valve blocked closed |
MIL |
FnR_DNOx2_V74 Power Reduction Long Term failure |
|
UDS DCU15 |
003D59 |
UREA dosing valve blocked |
059PUDB |
6 5 |
06 05 |
UREA Dosing valve blocked open UREA Dosing Valve blocked closed |
MIL |
FnR_DNOx2_V74 Long Term failure |
|
UDS DCU15 |
003D5A |
Plausibility of UDV stuck |
05A_PUQP |
6 5 |
06 05 |
UREA Dosing Valve blocked closed UREA Dosing valve blocked open |
|||
UDS DCU15 |
003D5B |
UDV valve stuck position unknown error |
05B_PUVP |
7 |
07 |
Plausibility of UDV valve position unknown |
|||
UDS DCU15 |
003D61 |
Line Heater back Flow tube |
061_PBFH |
6 5 |
06 05 |
Short circuit to ground Short circuit to battery Open load |
FnR_DNOx2_p910vC241 |
||
UDS DCU15 |
003D61 |
Line Heater back Flow tube |
061PBFH |
4 |
04 |
Short circuit to ground |
FnR_DNOx2_V74 |
||
3 5 |
03 05 |
Short circuit to battery Open load |
|||||||
UDS DCU15 |
003D63 |
Line Heater Inlet tube |
063_PILH |
6 3 5 |
06 03 05 |
Short circuit to ground Short circuit to battery Open load |
FnR_DNOx2_p910vC241 |
||
UDS DCU15 |
003D63 |
Line Heater Inlet tube |
063PILH |
4 3 5 |
04 03 05 |
Short circuit to ground Short circuit to battery Open load |
FnR_DNOx2_V74 |
||
UDS DCU15 |
003D64 |
Filter outlet connector heater |
064_POCH |
6 3 5 |
06 03 05 |
Short circuit to ground Short circuit to battery Open load |
FnR_DNOx2_p910vC241 |
||
UDS DCU15 |
003D64 |
Filter outlet connector heater |
064POCH |
4 |
04 |
Short circuit to ground |
FnR_DNOx2_V74 |
||
3 5 |
03 05 |
Short circuit to battery Open load |
|||||||
UDS DCU15 |
003D65 |
Line Heater Compensation tube |
065_PPCH |
6 3 5 |
06 03 05 |
Short circuit to ground Short circuit to battery Open load |
FnR_DNOx2_p910vC241 |
||
UDS DCU15 |
003D65 |
Line Heater Compensation tube |
065PPCH |
4 3 5 |
04 03 05 |
Short circuit to ground Short circuit to battery Open load |
FnR_DNOx2_V74 |
||
UDS DCU15 |
003D66 |
Heater of UREA Pump |
066_PPHT |
6 3 5 |
06 03 05 |
short circuit to ground (UB5) short circuit to bat (UB5) Open circuit / broken pump module heater PTC |
FnR_DNOx2_p910vC241 |
||
UDS DCU15 |
003D66 |
Heater of UREA Pump |
066PPHT |
4 |
04 |
short circuit to ground (UB5) |
FnR_DNOx2_V74 |
||
3 7 |
03 07 |
short circuit to bat (UB5) Open circuit / broken pump module heater PTC |
|||||||
UDS DCU15 |
003D67 |
Line Heater pressure tube (Box-Dosing module) |
067_PPLH |
6 3 5 |
06 03 05 |
Short circuit to ground Short circuit to battery Open load |
FnR_DNOx2_p910vC241 |
||
UDS DCU15 |
003D67 |
Line Heater pressure tube (Box-Dosing module) |
067PPLH |
4 3 5 |
04 03 05 |
Short circuit to ground Short circuit to battery Open load |
FnR_DNOx2_V74 Long Term failure |
ECU Name |
SPN [Hex] |
Fault Component |
Description |
FMI [DEC] |
FMI [HEX] |
FMI Description |
Lamp status |
Comment |
|
UDS DCU15 |
003D68 |
Tank heating Valve |
068_PUHT |
6 3 5 |
06 03 05 |
Short circuit to ground Short circuit to battery Open load |
FnR_DNOx2_p910vC241 |
||
UDS DCU15 |
003D68 |
Tank heating Valve |
068PUHT |
4 3 5 |
04 03 05 |
Short circuit to ground Short circuit to battery Open load |
FnR_DNOx2_V74 |
||
UDS DCU15 |
003D69 |
Heater of cooling line |
069_PCLH |
6 3 5 |
06 03 05 |
Short circuit to ground Short circuit to battery Open load |
FnR_DNOx2_p910vC241 |
||
UDS DCU15 |
003D69 |
Heater of cooling line |
069PCLH |
4 3 5 |
04 03 05 |
Short circuit to ground Short circuit to battery Open load |
FnR_DNOx2_V74 |
||
UDS DCU15 |
003D6A |
Heater of filterbox (UB5) |
06A_PFHT |
6 3 5 |
06 03 05 |
Short circuit to Ground short circuit to battery Open circuit |
FnR_DNOx2_p910vC241 |
||
UDS DCU15 |
003D6A |
Heater of filterbox (UB5) |
06APFHT |
4 3 7 |
04 03 07 |
Short circuit to Ground short circuit to battery Open circuit |
FnR_DNOx2_V74 |
||
UDS DCU15 |
003D73 |
Temperature after catalyst too low |
073_SCTD |
7 |
07 |
Down stream catalyst temp — physical (Catalyst heating time failed) |
FnR_DNOx2_p910vC241 |
||
UDS DCU15 |
003D73 |
Temperature after catalyst too low |
073SCTD |
7 |
07 |
Down stream catalyst temp — physical (Catalyst heating time failed) |
MIL |
FnR_DNOx2_V74 Long Term failure |
|
UDS DCU15 |
003D74 |
UREA pressure too low at system start |
074_SMOT |
2 |
02 |
UREA pressure too low at system start |
MIL |
Power Reduction Long Term failure |
|
UDS DCU15 |
003D75 |
UREA pressure too high |
075_SUPR |
2 |
02 |
Urea pressure not plausible (urea pressure too high) |
MIL |
Long Term failure |
|
UDS DCU15 |
003D76 |
UREA Temperature in Pump Module out of range |
076_SUTB |
7 |
07 |
Urea temperature box — physical (Urea Box Temp NOT OK: outside range) |
MIL |
Long Term failure |
|
UDS DCU15 |
003D77 |
UREA Temperature in Tank out of range |
077_SUTT |
7 |
07 |
Urea temperature tank — physical (Urea Tank Temp NOT OK: outside range) |
|||
UDS DCU15 |
003D78 |
System frozen and not free in time |
078_HHSM |
7 8 9 10 |
07 08 09 0A |
Defreezing Mode and Detection Errors (Inlet line defreezing failed) Defreezing Mode and Detection Errors (pressure line defreezing failed) Defreezing Mode and Detection Errors (pressure build-up in detection mode failed) Defreezing Mode and Detection Errors (Back-flow line defreezing failed) |
MIL |
Power Reduction Long Term failure |
|
UDS DCU15 |
003D7A |
Coolant control valve mechanicallly |
07ACCVD |
6 5 |
06 05 |
mechanical defective blocked closed mechanical defective blocked open |
FnR_DNOx2_V74 Power Reduction |
||
UDS DCU15 |
003D7B |
Reverting valve (4-2way valve?) mechanically |
07B_ERVV |
7 |
07 |
valve does not open |
|||
UDS DCU15 |
003D7C |
Startup cycle counter for pressure drop during dosing |
07C_SPCC |
7 |
07 |
Start up cycle counter for pressure drops during dosing exceed maximum |
Power Reduction |
||
UDS DCU15 |
003D7E |
Battery Voltage (actual value) |
07E_BMON |
4 3 |
04 03 |
Low battery voltage High battery voltage |
MIL |
Power Reduction (FnR_DNOx2_p910vC241) Long Term failure |
|
UDS DCU15 |
003D82 |
UREA pressure too low (in «commissioning» status) |
082_SMOTC |
2 |
02 |
Pump motor error during commissioning (pump not delivering) |
|||
UDS DCU15 |
003D83 |
UREA Temperature too low during commissionning |
083_STMPC |
2 |
02 |
Temperatures not plausible during commissioning. |
|||
UDS DCU15 |
003D85 |
Coolant control valve mechanically (Commissioning) |
085_SCCVC |
2 |
02 |
Blocked closed |
|||
UDS DCU15 |
003D93 |
Static Leakage Test failed |
093_SLKS |
7 |
07 |
static leakage detected (during system state 0) |
|||
UDS DCU15 |
003D94 |
Catalyst efficiency too low (with NOx sensor) |
094UCAT |
12 7 |
0C 07 |
Catalyst efficiency too low |
FnR_DNOx2_V74 |
||
UDS DCU15 |
003D95 |
Empty UREA Tank |
095_ELMT |
7 |
07 |
urea tank empty |
MIL |
Long Term failure |
|
UDS DCU15 |
003D96 |
UREA Level Indication not plausible with UREA consumption |
096_PULV |
7 |
07 |
Urea Level Plausibility Error |
Long Term failure |
||
UDS DCU15 |
003D9A |
Dynamic Leakage Test failed |
09ASLKD |
12 |
0C |
dynamic leakage detected (during system state 1) |
MIL |
FnR_DNOx2_V74 Power Reduction Long Term failure |
|
UDS DCU15 |
003D9C |
Urea tank heater valve blocked open |
09C_HUHT |
7 |
07 |
Tank heater valve blocked open |
|||
UDS DCU15 |
003D9C |
Urea tank heater valve blocked open |
09CHUHT |
7 |
07 |
Tank heater valve blocked open |
FnR_DNOx2_V74 |
||
UDS DCU15 |
003D9D |
NOx sensor measures too high NOx |
09DUPPM |
12 |
0C |
NOx ppm not plausible |
FnR_DNOx2_V74 |
||
UDS DCU15 |
003DA1 |
CAN receive frame E2SCR (Dosing,Exh gas flow,Exh gas temp,Error Supression, Heater, Long Term failure) |
0A1_CE2S |
9 10 2 12 7 12 |
09 0A 02 0C 07 0C |
09: timeout 0A: too many CAN messages 02: SAE J1939 Check for CAN receive signal : (UREA quantity not in range) 0C: SAE J1939 Check for CAN receive signal : (Heating status not in range) |
MIL |
Long Term failure |
|
12 12 |
0C 0C |
07: SAE J1939 Check for CAN receive signal : (Dosing status not in range) 0C: SAE J1939 Check for CAN receive signal : (PTO status not in range) 0C: SAE J1939 Check for CAN receive signal : (Exhaust gas mass flow not in range) 0C: SAE J1939 Check for CAN receive signal : (Exhaust gas temperature not in range) |
|||||||
UDS DCU15 |
003DA2 |
CAN receive frame E2SCR extended (Dosing,Exh gas flow,Exh gas temp,Error Supression, Heater, Long Term failure) |
0A2_CE2S2 |
2 12 |
02 0C |
SAE J1939 Check for CAN receive signal : (Long term error active signal not in Range) SAE J1939 Check for CAN receive signal : (Error suppression Signal not in range) |
MIL |
Long Term failure |
|
UDS DCU15 |
003DA3 |
CAN receive frame EEC1 (Driver demand, eng speed, eng torque) |
0A3_CEEC |
9 10 12 2 7 |
09 0A 0C 02 07 |
timeout too many CAN messages SAE J1939 Check for CAN receive signal : (Torque driver demand not in range) SAE J1939 Check for CAN receive signal : (Engine torque not in range) SAE J1939 Check for CAN receive signal : (Engine speed not in range) |
|||
UDS DCU15 |
003DA4 |
CAN receive frame ET1 (Oil and Water temp engine) |
0A4_CET1 |
9 10 12 2 |
09 0A 0C 02 |
timeout too many CAN messages SAE J1939 Check for CAN receive signal : (Water temperature not in range) SAE J1939 Check for CAN receive signal : (Oil temperature not in range) |
|||
UDS DCU15 |
003DA6 |
CAN receive frame IC1 (Boost press, Manifold Temp) |
0A6_CIC1 |
9 10 12 2 |
09 0A 0C 02 |
timeout too many CAN messages SAE J1939 Check for CAN receive signal : (Boost pressure not in range) SAE J1939 Check for CAN receive signal : (Intake manifold 1 temperature not in range) |
|||
UDS DCU15 |
003DA7 |
CAN receive frame LFE (Fuel Rrate) |
0A7_CLFE |
9 10 12 |
09 0A 0C |
timeout too many CAN messages SAE J1939 Check for CAN receive signal : (Fuel rate not in range) |
|||
UDS DCU15 |
003DA8 |
CAN receive frame NO1 (NOx concentration, NOx Sensor state) |
0A8CNO1 |
9 10 12 2 |
09 0A 0C 02 |
timeout too many CAN messages SAE J1939 Check for CAN receive signal : (Nox concentration not in range) SAE J1939 Check for CAN receive signal : (Nox status not in range) |
FnR_DNOx2_V74 |
||
UDS DCU15 |
003DA9 |
DCU or Heater switched «off» too long time via CAN |
0A9_CTIM |
9 10 12 |
09 0A 0C |
Heater disabled by CAN request for a too long time Dosing disabled by CAN request for a too long time Error suppression via CAN request for a too long time |
FnR_DNOx2_p910vC241 |
||
UDS DCU15 |
003DA9 |
DCU or Heater switched «off» too long time via CAN |
0A9CTIM |
9 10 |
09 0A |
Heater disabled by CAN request for a too long time Dosing disabled by CAN request for a too long time |
FnR_DNOx2_V74 Long Term failure |
||
UDS DCU15 |
003DAA |
UREA Tank level error (CAN message or |
0AA_EULS |
9 |
09 |
09: timeout |
FnR_DNOx2_p910vC241 |
||
electrical with real sensor) |
10 2 3 4 11 |
0A 02 03 04 0B |
0A: too many CAN messages 02: SAE J1939 range check: UREA tank level out of range 03: Level over CAN: SAE J1939 Signal Not in Range Level sensor connected directly: SRC high 04: Level over CAN: SAE J1939 Erraneous Signal Level sensor connected directly: SRC low 0B: Level over CAN: SAE J1939 no Signal available Level sensor connected directly: Sensor Supply error |
||||||
UDS DCU15 |
003DAA |
UREA Tank level error (CAN message or electrical with real sensor) |
0AAEULS |
3 4 2 |
03 04 02 |
03: Level over CAN: SAE J1939 Signal Not in Range Level sensor connected directly: SRC high 04: Level over CAN: SAE J1939 Erraneous Signal Level sensor connected directly: SRC low 02: Level over CAN: SAE J1939 no Signal available Level sensor connected directly: Sensor Supply error |
MIL |
FnR_DNOx2_V74 |
|
UDS DCU15 |
003DAC |
UREA quality sensor re lated errors CAN |
0ACCUQS |
9 10 12 |
09 0A 0C |
timeout too many CAN messages SAE J1939 Check for CAN receive signal : (UREA quality signal not in range) |
FnR_DNOx2_V74 |
||
UDS DCU15 |
003DAD |
CAN receive frame Time/Date |
0AD_CTDA |
9 10 12 12 12 12 |
09 0A 0C 0C 0C 0C |
timeout too many CAN messages SAE J1939 range check error of seconds SAE J1939 range check error of minutes SAE J1939 range check error of hours SAE J1939 range check error of months |
|||
7 7 |
07 07 |
SAE J1939 range check error of days SAE J1939 range check error of years |
|||||||
UDS DCU15 |
003DB1 |
Ambient Temperature: SAE J1939 Check for CAN receive signal : (Signal Range Check: Signal not in range / Erroreous Signal / Signal not available) |
0B1_CAMB |
9 10 12 2 |
09 0A 0C 02 |
timeout too many CAN messages SAE J1939 Check for CAN receive signal : (Barometric pressure not in range) SAE J1939 Check for CAN receive signal : (Ambient air temperature not in range) |
|||
UDS DCU15 |
003DB8 |
CAN receive frame PROA (Fuel quantity) |
0B8_CPRO |
9 10 12 2 |
09 0A 0C 02 |
timeout too many CAN messages SAE J1939 Check for CAN receive signal : (UREA tank level not in range) |
|||
7 |
07 |
SAE J1939 Check for CAN receive signal : (UREA tank temperature not in range) SAE J1939 Check for CAN receive signal : (Fuel injection quantity not in range) |
|||||||
UDS DCU15 |
003DBC |
Detection of blocked filter |
0BCDBFE |
7 |
07 |
Error detection of blocked Filter |
FnR_DNOx2_V74 Long Term failure |
||
UDS DCU15 |
003DBD |
Warning for detection of blocked filter |
0BDDBFW |
7 |
07 |
Warning for detection of blocked Filter |
FnR_DNOx2_V74 |
ECU Name |
SPN [Hex] |
Fault Component |
Description |
FMI [DEC] |
FMI [HEX] |
FMI Description |
Lamp status |
Comment |
||
UDS DCU15 |
003DBE |
CAN receive frame TC1 |
0BE_CTC1 |
9 10 12 |
09 0A 0C |
timeout too many CAN messages SAE J1939 Check for CAN receive signal : (Vehicle speed not in range) |
||||
UDS DCU15 |
003DC1 |
Too many Frozen Cycles of dosing module |
0C1_EFCC |
9 10 |
09 0A |
additional frozen cycle counter (eepm_ct_frz2_uc) exceeded maximum frozen cycle counter (eepm_ct_frz_uc) exceeded maximum |
||||
UDS DCU15 |
003DC2 |
Application error in MAP selection for UREA quantity calculation |
0C2UDVC |
13 |
0D |
map selection error (11 map calculation) |
FnR_DNOx2_V74 |
|||
UDS DCU15 |
003DC3 |
CAN receive frame EEC3 |
0C3_CEC3 |
9 10 2 12 12 |
09 0A 02 0C 0C |
09: timeout 0A: too many CAN messages 02: SAE J1939 Check for CAN receive signal : (Exhaust Gas Mass FLown not in range) 0C: SAE J1939 Check for CAN receive signal : (Intake Dew Point not in range) 0C: SAE J1939 Check for CAN receive signal : (Exhaust Dew Point not in range) |
||||
UDS DCU15 |
003DC4 |
CAN receive frame EGF1 |
0C4_CEGF |
9 10 2 |
09 0A 02 |
09: Warning for detection of blocked Filter 0A: too many CAN messages 02: SAE J1939 Check for CAN receive signal : (Engine Inlet Air Mass Flow Rate not in range) |
||||
UDS DCU15 |
003DC5 |
CAN receive frame EEC5 |
0C5_CEC5 |
9 10 2 |
09 0A 02 |
09: timeout 0A: too many CAN messages 02: SAE J1939 Check for CAN receive signal : (EGR Valve Control not in range) |
||||
UDS DCU15 |
003DC6 |
CAN receive frame EC1BAM |
0C6_CECB |
9 2 |
09 02 |
Error detection of blocked Filter SAE J1939 Check for CAN receive signal : (Reference Engine torque not in range) |
||||
UDS DCU15 |
003DC7 |
CAN receive frame PROB |
0C7_CPRB |
9 10 |
09 0A |
timeout too many CAN messages |
||||
UDS DCU15 |
003DC8 |
CAN receive frame ERC1 |
0C8_CERC |
9 10 2 |
09 0A 02 |
timeout too many CAN messages SAE J1939 Check for CAN receive signal : (Retarder Percent Torque not in range) |
||||
UDS DCU15 |
003DC9 |
CAN Bus OFF error |
0C9_CBOF |
9 10 |
09 0A |
BUS OFF error CAN1 BUS OFF Error CAN2 |
||||
UDS DCU15 |
003DCA |
Load point evaluation |
0CA_AELP |
3 4 |
03 04 |
signal high signal low |
||||
UDS DCU15 |
003DCB |
Load point evaluation (above and below limit) |
0CB_AELP2 |
0 1 |
00 01 |
signal high signal low |
||||
UDS DCU15 |
003DCC |
Atmospheric pressure evaluation |
0CC_EAPS |
12 |
0C |
SAE J1939 range check: barometric pressure out of range |
||||
UDS DCU15 |
003DD1 |
EEPROM / Checksum failures |
0D1_EEPM |
12 13 8 2 |
0C 0D 08 02 |
EEPROM Detection error Wrong EEPROM size EEPROM communication error EEPROM write error |
MIL |
Long Term failure |
||
7 12 |
07 0C |
No corresponding variant number error Codierwort error |
||||||||
UDS DCU15 |
003DD2 |
Ingition «on» signal K15 |
0D2_EK15 |
2 |
02 |
digital input ignition ON not sensed during initialisation |
||||
UDS DCU15 |
003DD3 |
Main Relay opens too early / too late |
0D3_EMRL |
6 3 5 4 |
06 03 05 04 |
main relay shut off too early (before EEPROM update) main relay shut off too late main relay open circuit main relay short circuit |
MIL |
|||
UDS DCU15 |
003DD4 |
Too high UREA Temperature in Pump module (Emergency shut off) |
0D4_EMRS |
7 |
07 |
over temperature detection (urea temp. in pump module) |
FnR_DNOx2_p910vC241 Power Reduction |
|||
UDS DCU15 |
003DD4 |
Too high UREA Temperature in Pump module or Leakage test failed (Emergency shut off) |
0D4EMRS |
7 12 |
07 0C |
over temperature detection (urea temp. in pump module) urea leakage detection (static or dynamic) |
MIL |
FnR_DNOx2_V74 Power Reduction Long Term failure |
||
UDS DCU15 |
003DE1 |
Plausibility of downstream catalyst temperature sensor (after SCR catalyst) |
0E1_PCTD |
13 12 7 |
0D 0C 07 |
dynamic plausibility test — lower threshold dynamic plausibility test — upper threshold static plausibility test |
FnR_DNOx2_p910vC241 |
|||
UDS DCU15 |
003DE1 |
Plausibility of downstream catalyst temperature sensor (after SCR catalyst) |
0E1PCTD |
12 7 |
0C 07 |
dynamic plausibility test — upper threshold static plausibility test |
MIL |
FnR_DNOx2_V74 |
||
UDS DCU15 |
003DE2 |
Plausibility of upstream catalyst temperature sensor (before SCR catalyst) |
0E2_PCTU |
13 12 7 |
0D 0C 07 |
dynamic plausibility test — lower threshold dynamic plausibility test — upper threshold static plausibility test |
FnR_DNOx2_p910vC241 |
|||
UDS DCU15 |
003DE2 |
Plausibility of upstream catalyst temperature sensor (before SCR catalyst) |
0E2PCTU |
12 7 |
0C 07 |
dynamic plausibility test — upper threshold static plausibility test |
MIL |
FnR_DNOx2_V74 |
||
UDS DCU15 |
003DE3 |
Urea pressure sensor plausibility error (checked during system startup) |
0E3_PUPS |
12 |
0C |
Uplausibility UREA pressure sensor (dynamic) |
MIL |
Power Reduction Long Term failure |
||
UDS DCU15 |
003DE4 |
Urea box temperature sensor plausibility error (dynamic / static) |
0E4_PUTB |
7 |
07 |
Plausibility of pump module temp. sensor (static) |
FnR_DNOx2_p910vC241 |
|||
UDS DCU15 |
003DE4 |
Urea box temperature sensor plausibility error (dynamic / static) |
0E4PUTB |
12 7 |
0C 07 |
Plausibility of pump module temp. sensor (dynamic) Plausibility of pump module temp. sensor (static) |
FnR_DNOx2_V74 |
|||
UDS DCU15 |
003DE5 |
Urea tank temperature sensor plausibility error (dynamic / static) |
0E5_PUTT |
7 |
07 |
Plausibility of urea tank temp. sensor (static) |
FnR_DNOx2_p910vC241 |
|||
UDS DCU15 |
003DE5 |
Urea tank temperature sensor plausibility error (dynamic / static) |
0E5PUTT |
12 7 |
0C 07 |
Plausibility of urea tank temp. sensor (dynamic) Plausibility of urea tank temp. sensor (static) |
FnR_DNOx2_V74 |
|||
UDS DCU15 |
003DE6 |
UREA Tank Temperature not plausible with Pump module temperature |
0E6_EUTT |
9 10 2 3 |
09 0A 02 03 |
09: Temp over CAN: SAE J1939 Timeout Temp sensor connected directly: SRC high 0A: Temp over CAN: SAE J1939 Too many messages Temp sensor connected directly: SRC low |
FnR_DNOx2_p910vC241 |
|||
4 0 1 |
04 00 01 |
02: Temp over CAN: SAE J1939 erroneous signal 03: SRC High: raw value UREA temperature too high 04: SRC Low: raw value UREA temperature too low 00: SRC High: diagnostic value UREA temperature too high 01: SRC Low: diagnostic value UREA temperature too low |
||||||||
UDS DCU15 |
003DE6 |
UREA Tank Temperature not plausible with Pump module temperature |
0E6EUTT |
3 4 2 |
03 04 02 |
03: Temp over CAN: SAE J1939 Timeout Temp sensor connected directly: SRC high 04: Temp over CAN: SAE J1939 Too many messages Temp sensor connected directly: SRC low 02: Temp over CAN: SAE J1939 erroneous signal |
FnR_DNOx2_V74 |
|||
UDS DCU15 |
003DE7 |
Back flow line blocked |
0E7_SBFL |
7 |
07 |
back flow line blocked |
Power Reduction |
|||
UDS DCU15 |
003DE8 |
Urea pressure not reduced during start up |
0E8_SCCV |
2 |
02 |
Blocked closed |
MIL |
Long Term failure |
||
UDS DCU15 |
003DEA |
Pressure line blocked |
0EA_SPRL |
7 |
07 |
pressure line blocked |
MIL |
Power Reduction Long Term failure |
||
UDS DCU15 |
003DEB |
Low UREA level 1 (warning) |
0EB_EUL1 |
1 |
01 |
UREA level below Limit 1 |
||||
UDS DCU15 |
003DEC |
Low UREA level 2 (warning) |
0EC_EUL2 |
1 |
01 |
UREA level below Limit 2 |
||||
UDS DCU15 |
003DF0 |
Group error path UREA injection control |
0F0_LCNP |
12 |
0C |
Error belonging to group UREA Injection control |
MIL |
Long Term failure |
||
UDS DCU15 |
003DF1 |
Group error path Air control |
0F1_LDIN |
12 |
0C |
Error belonging to group air control |
MIL |
Long Term failure |
||
UDS DCU15 |
003DF2 |
Group error path catalyst temperature |
0F2_LIUQ |
12 |
0C |
Error belonging to group catalyst temperature out of range |
MIL |
Long Term failure |
||
UDS DCU15 |
003DF3 |
Group error path NOx exceeded |
0F3LNTE |
12 |
0C |
Error belonging to group NOx exceeded active |
MIL |
FnR_DNOx2_V74 Long Term failure |
||
UDS DCU15 |
003DF4 |
Group error path UREA Tank empty |
0F4_LTEM |
12 |
0C |
Error belonging to group UREA tank empty active |
MIL |
Long Term failure |
Автомобиль IVECO STRALIS не работали задние поворотники, задний левый стоп сигнал. На машину выехал наш специалист, первым делом была произведена компьютерная диагностика, а затем выполнили диагностику и ремонт электропроводки т.к. было короткое замыкание. Ошибки в блоке управления не исчезли. После первичной проверки блока выяснилось, что рамный модуль RFC требует ремонта. Проблема крылась в блоке, из-за короткого замыкания на проводах в электронном модуле сгорели силовые каскады и логические микросхемы. Ремонт блока произвели в кротчайшие сроки.
Для записи на ремонт или ответ на интересующие вопросы обращайтесь по телефону:
РАБОТАЕМ СО ВСЕЙ РОССИЕЙ, УСЛУГИ ТРАНСПОРТНОЙ КОМПАНИИ НЕ ТАКИЕ ДОРОГИЕ
Для заявки на ремонт ЭЛЕКТРОНИКИ пользуйтесь формой
ПЕРЕЧЕНЬ СХЕМ ЭЛЕКТРИЧЕСКИХ Iveco STRALIS.
электрическая схема № 1: ЗАПУСК ДВИГАТЕЛЯ
электрическая схема № 2: ПРЕДПУСКОВОЙ ПОДОГРЕВ ДВИГАТЕЛЯ
электрическая схема № 3: ПОДЗАРЯДКА АККУМУЛЯТОРНОЙ БАТАРЕИ
электрическая схема № 4: КОНТРОЛЬНЫЕ ПРИБОРЫ (ТАХОГРАФ — ТАХОМЕТР)
электрическая схема № 5: КОНТРОЛЬНЫЕ ПРИБОРЫ (УРОВЕНЬ ТОПЛИВА —ТЕМПЕРАТУРА ОХЛАЖДАЮЩЕЙ ЖИДКОСТИ —ТЕМПЕРАТУРА МАСЛА — ВОЛЬТМЕТР)
электрическая схема № 6: КОНТРОЛЬНЫЕ ПРИБОРЫ (УРОВЕНЬ/ДАВЛЕНИЕ МОТОРНОГО МАСЛА — ДАВЛЕНИЕ В ТОРМОЗНОЙ ПНЕВМОСИСТЕМЕ)
электрическая схема № 7: КОНТРОЛЬНЫЕ ПРИБОРЫ (ИЗНОС ТОРМОЗНЫХ КОЛОДОК — НАГРУЗКА НА ОСИ — ЭКОНОМЕР)
электрическая схема № 8: КОНТРОЛЬНЫЕ ЛАМПЫ
электрическая схема № 9: СТОЯНОЧНОЕ ОСВЕЩЕНИЕ (ВНУТРИ КАБИНЫ)
электрическая схема № 10: ГАБАРИТНЫЕ ФОНАРИ (НАРУЖНОЕ ОСВЕЩЕНИЕ)
электрическая схема № 11: ФАРЫ БЛИЖНЕГО И ДАЛЬНЕГО СВЕТА
электрическая схема № 12: ДОПОЛНИТЕЛЬНЫЕ ФАРЫ И ЗАДНИЕ ПРОТИВОТУМАННЫЕ ФОНАРИ
электрическая схема № 13: УКАЗАТЕЛИ ПОВОРОТА И ФОНАРИ АВАРИЙНОЙ СИГНАЛИЗАЦИИ
электрическая схема № 14: СТОП СИГНАЛЫ — ФОНАРИ ЗАДНЕГО ХОДА
электрическая схема № 15: СТЕКЛООЧИСТИТЕЛЬ — СИГНАЛЫ ЗВУКОВЫЕ
электрическая схема № 16: ВНУТРЕННЕЕ ОСВЕЩЕНИЕ И ВСПОМОГАТЕЛЬНЫЕ КОНТУРЫ
электрическая схема № 17: ПОДСВЕТКА КОМБИНАЦИИ ПРИБОРОВ
электрическая схема № 18: ЗЕРКАЛА ЗАДНЕГО ВИДА
электрическая схема № 19: СТЕКЛОПОДЪЕМНИКИ
электрическая схема № 20: ЦЕНТРАЛЬНЫЙ ЗАМОК
электрическая схема № 21: ОТКИДЫВАНИЕ КАБИНЫ — ПРИВОД ВЕНТИЛЯТОРА СИСТЕМЫ ОХЛАЖДЕНИЯ ДВИГАТЕЛЯ
электрическая схема № 22: ГЛАВНЫЙ РАЗМЫКАТЕЛЬ МАССЫ (TGC)
электрическая схема № 23: EDC (РАЗЪЕМ «В»)
электрическая схема № 24: EDC (РАЗЪЕМ «A»)
электрическая схема № 25: АВТОМАТИЧЕСКАЯ УСТАНОВКА КЛИМАТ КОНТРОЛЯ
электрическая схема № 26: РУЧНОЕ УПРАВЛЕНИЕ КОНДИЦИОНЕРОМ
электрическая схема № 27: АВТОМАТИЧЕСКАЯ КОРОБКА ПЕРЕДАЧ EUROTRONIC
электрическая схема № 28: EBS
электрическая схема № 29: АБС
электрическая схема № 30: ECAS ТЯГАЧЕЙ 4 2
электрическая схема № 31: ECAS АВТОМОБИЛЕЙ 4 FP
электрическая схема № 32: ECAS АВТОМОБИЛЕЙ 6 4 P
электрическая схема № 33: ECAS АВТОМОБИЛЕЙ 6 2 C
электрическая схема № 34: ECAS АВТОМОБИЛЕЙ 6 2 P/FP
электрическая схема № 35: ГИДРОДИНАМИЧЕСКИЙ ТОРМОЗEЗАМЕДЛИТЕЛЬ ZFEINTARDER
электрическая схема № 36: ЛИНИЯ CAN «BCB»
электрическая схема № 37: ЛИНИЯ CAN «VDB»
электрическая схема № 38: ЛИНИЯ CAN «ICB»
электрическая схема № 39: ЛИНИЯ CAN «DB»
электрическая схема № 40: ЛИНИЯ CAN «SB» АБС
электрическая схема № 41: ЛИНИЯ CAN «SB» EBS
электрическая схема № 42: IC (КОМБИНАЦИЯ ПРИБОРОВ)
электрическая схема № 43: ИНТЕРФЕЙС РУЛЕВОЙ КОЛОНКИ (SWI)
электрическая схема № 44: МОДУЛЬ КАБИНЫ (СM)
электрическая схема № 45: ПРИКРОВАТНЫЙ МОДУЛЬ (BM)
электрическая схема № 46: МОДУЛЬ ДВЕРИ ВОДИТЕЛЯ (DDM)
электрическая схема № 47: МОДУЛЬ ДВЕРИ ПАССАЖИРА (РDM)
электрическая схема № 48: ЭБУ ПЕРЕДНЕГО КОНТУРА ЭЛЕКТРОННОГО ОБОРУДОВАНИЯ (FFC)
электрическая схема № 49: ЭБУ ЗАДНЕГО КОНТУРА ЭЛЕКТРОННОГО ОБОРУДОВАНИЯ (RFC)
электрическая схема № 50: БОРТОВОЙ КОМПЬЮТЕР (BC)
электрическая схема № 51: ЛЮК КРЫШИ КАБИНЫ С ЭЛЕКТРОПРИВОДОМ/СОЛНЦЕЗАЩИТНЫЕ ШТОРКИ
электрическая схема № 52: РАДИОПРИЕМНИК
электрическая схема № 53: ИММОБИЛАЙЗЕР
электрическая схема № 54: КОРОБКА ОТБОРА МОЩНОСТИ (АВТОМОБИЛИ С МЕХАНИЧЕСКОЙ КП)
электрическая схема № 55: 15-и КОНТАКТНЫЙ РАЗЪЕМ ДЛЯ ПОДКЛЮЧЕНИЯ ОБОРУДОВАНИЯ ПРИЦЕПА
электрическая схема № 56: ДИАГНОСТИЧЕСКИЙ РАЗЪЕМ
электрическая схема № 57: РАЗЪЕМ ДЛЯ УСТАНОВЩИКОВ ОБОРУДОВАНИЯ
электрическая схема № 58: ДОПОЛНИТЕЛЬНЫЙ ЖИДКОСТНОЙ ОТОПИТЕЛЬ (РУЧНОЕ УПРАВЛЕНИЕ)
электрическая схема № 59: ДОПОЛНИТЕЛЬНЫЙ ЖИДКОСТНОЙ ОТОПИТЕЛЬ (АВТОМАТИЧЕСКОЕ УПРАВЛЕНИЕ)
электрическая схема № 60: ДОПОЛНИТЕЛЬНЫЙ ВОЗДУШНЫЙ ОТОПИТЕЛЬ (РУЧНОЕ УПРАВЛЕНИЕ)
электрическая схема № 61: ОБОГРЕВ ВЕТРОВОГО СТЕКЛА
электрическая схема № 62: ПОДОГРЕВ ФИЛЬТРА ГРУБОЙ ОЧИСТКИ ТОПЛИВА
электрическая схема № 63: ОБОГРЕВ СИДЕНИЙ
Владельцы грузовиков Iveco Stralis могут столкнуться с проблемой, связанной с ошибкой RFC. Эта ошибка проявляется тем, что блок управления двигателем начинает гореть во время движения. Как правило, это происходит из-за неисправности в работе системы подачи топлива или из-за низкого давления в системе.
Ошибка RFC может привести к серьезным последствиям, таким как остановка двигателя, увеличение расхода топлива, а также увеличение износа механизмов. Поэтому необходимо своевременно проверять систему топлива и давление в системе.
Если вы столкнулись с проблемой ошибки RFC на грузовике Iveco Stralis, не стоит откладывать визит к специалисту. Ремонт этой ошибки может потребовать замены датчиков, системы впрыска или насоса топлива. В любом случае ремонт требует профессионального подхода и квалифицированных мастеров автосервиса.
Важно помнить, что устранение ошибки RFC на грузовике Iveco Stralis требует быстрого и правильного реагирования. Иначе последствия могут быть непредсказуемыми и привести к серьезным поломкам автомобиля.
Кроме того, следует проверять работу прицепа, поскольку неисправности в подвеске и тормозной системе могут также привести к возникновению ошибки RFC на грузовике Iveco Stralis.
Ошибка RFC Iveco Stralis: расшифровка и причины
Ошибка RFC, которая иногда появляется на панели управления Iveco Stralis, может быть связана с несколькими причинами. Одной из основных является проблема с датчиком давления валика. Этот датчик отвечает за измерение давления в системе смазки головки блока цилиндров.
Если давление в системе смазки головки блока цилиндров ниже нормы, то возникает ошибка RFC. В этом случае необходимо проверить датчик давления и принять меры по его замене, если требуется. Также следует проверить работу системы смазки и необходимость ее ремонта.
Еще одной возможной причиной ошибки RFC на Iveco Stralis является проблема с прицепом. Если прицеп не правильно подключен или возникла какая-то неисправность, то это может привести к возникновению ошибки RFC на панели управления грузовика. В этом случае следует проверить состояние прицепа и принять меры по его ремонту.
Когда ошибка RFC горит на панели управления Iveco Stralis, это может свидетельствовать о неисправности какого-то другого блока или датчика. Проверьте все системы и датчики грузовика, чтобы выявить возможную причину ошибки. Если вы не можете найти неисправность самостоятельно, обратитесь к специалистам по ремонту Iveco Stralis для диагностики и устранения проблемы.
Что такое ошибка RFC Iveco Stralis?
Ошибка RFC (Регулирование Функций Шасси) на Iveco Stralis может вызывать различные проблемы, связанные с давлением в системе торможения прицепа. Эта ошибка связана с блоком регулятора давления, который не может прочитать сигналы от датчиков.
Когда эта ошибка возникает, многие водители отмечают, что горят предупреждающие лампы на приборной панели Iveco Stralis. Это может означать, что система торможения прицепа выключена или работает ненадежно.
Чтобы избежать возникновения проблем при эксплуатации Iveco Stralis, необходимо регулярно проверять работу блока регулятора давления и датчиков. Если же ошибка все же произошла, то ремонт может потребоваться как на стороне тягача, так и на стороне прицепа.
В целом, ошибка RFC на Iveco Stralis может быть серьезной угрозой безопасности вождения, поэтому ее необходимо решать незамедлительно.
Какие причины могут вызвать ошибку RFC Iveco Stralis
Ошибка RFC Iveco Stralis может возникнуть по многим причинам. Одной из основных причин является неправильное подключение прицепа к Stralis. Необходимо проверять правильность соединения между прицепом и головой тягача Stralis перед выездом на дорогу.
Определенные датчики Stralis могут также вызывать ошибку при неисправности. Важно проверять корректную работу всех датчиков, связанных с давлением воздуха, системы охлаждения двигателя и другие параметры.
Давление воздуха в системе также может стать причиной ошибки RFC Iveco Stralis. Перед выездом на дорогу нужно внимательно проверять уровень давления воздуха в шинах и убедиться, что он находится в пределах рекомендуемых значений.
Ремонт блоков Stralis может также привести к ошибкам в работе системы. При возникновении ошибки RFC Iveco Stralis, необходимо провести техническую диагностику устройства и произвести ремонт или замену неисправных блоков или компонентов.
Если при работе головы тягача Stralis неисправен один из процессоров, то может возникать ошибка RFC Iveco Stralis. Если индикатор на панели приборов горит, необходимо незамедлительно обратиться к специалисту для диагностики и быстрого устранения поломки.
Описание: Габариты следующие, длина — 3466, ширина — 1100, высота — 1637 мм. Колесная база составляет 2749 мм. Дорожный просвет 132 мм. Автомобиль оснащается гибридным силовым агрегатом. 4—цилиндровый двигатель оборудован системой обеспечивающей выходную мощность мотора. На каждый цилиндр приходится по 4 клапана. Диаметр одного цилиндра составляет 76 мм, ход поршня – 70 мм. Коленчатый вал двигателя разгоняется до 4000 оборотов в минуту. Максимальный крутящий момент удерживается вплоть до 5000 оборотов в минуту.
Cмотрите ВИДЕО про iveco ошибка ecm 99.
Оценка автовладельца по имени Вениамин : Комфортная, в городке шустрая, расход небольшой емкая я рыбак и лодка и мотор и снасти на троих влазят, подвеска мягенькая приятная, управление отличное
Категория: Ремонт своими руками
Дата выхода: 11. 12. 2019 года
Смех в теме: Сперва они говорят чувствовать себя как дома, а потом удивляются, почему ты закрываешься в ванной и рыдаешь.
Случилось неприятность ехал домой с грузом по обычным российским дорогам около 40км(больше совесть не позволяла) попал пару кочек и заглох…
Осмотрел все не нашел обрыва начал искать в интернете что это за чудеса такие(ошибки 97-100).
Нашел от тяжелых грузовых машин(Стралис Треккер Еврокарго) у них это ошибки надува и и расположение распредвала. Ок снял датчик давления(он же температуры воздуха)на впускном коллекторе
Прочистили мы его и промыли салярой.
Потом сняли датчик распредвала
и вуаля все работает ошибок нет…
Нету фото ремонта так как времени небыло делать их.
И да забыл сказать старый хозяин сказал что их никогда не менял и не трогал видимо моя очередь их менять. Пока расходы были на саляру для промывки
На этой страничке вы можете узнать коды неисправностей КПП евротроник для IVECO
Расшифровка показаний дисплея:
Расшифровка кодов неисправностей КПП евротроник для IVECO
КОД контакт ДИСПЛЕЙ ОПИСАНИЕ
Расшифровка мигающих кодов EDC MS6.2 SW 5.X
Мигающий код Контрольная лампа EDC Неисправность
ДВИГАТЕЛЬ
2.1 ВЫКЛЮЧЕНА Датчик температуры охлаждающей ‘жидкости
2.2 ВЫКЛЮЧЕНА Датчик температуры воздуха
2.3 ВЫКЛЮЧЕНА Датчик температуры топлива
2.4 светится постоянно Датчик давления наддува
2.5 ВЫКЛЮЧЕНА Датчик атмосферного давления (внутри блока управления)
2.6 светится постоянно Сигнал датчика моторного тормоза
3.5 ВЫКЛЮЧЕНА Напряжение аккумулятора
ТУРБИНА
4.1 ВЫКЛЮЧЕНА Датчик давления в приводе турбины
4.2 светится постоянно Датчик частоты вращения турбины
4.3 светится постоянно Повышенная частота вращения турбины
4.4 светится постоянно Управление турбиной (механическая неисправность)
4.5 светится постоянно Электромагнитный клапан турбины с изменяемой геометрией
4.6 МИГАЕТ Электромагнитный клапан управления моторным тормозом
ФОРСУНКИ
5.1 светится постоянно Неисправность форсунки цилиндра 1
5.2 светится постоянно Неисправность форсунки цилиндра 2
5.3 светится постоянно Неисправность форсунки цилиндра 3
5.4 светится постоянно Неисправность форсунки цилиндра 4
5.5 светится постоянно Неисправность форсунки цилиндра 5
5.6 светится постоянно Неисправность форсунки цилиндра 6
ДАТЧИКИ ЧАСТОТЫ ВРАЩЕНИЯ ДВИГАТЕЛЯ
6.1 светится постоянно Датчик на маховике
6.2 светится постоянно Датчик на шестерне газораспределительного механизма
6.4 МИГАЕТ Повышенная частота вращения двигателя
БЛОК УПРАВЛЕНИЯ
9.1 МИГАЕТ Неисправен блок управления
9.2 светится постоянно Ошибочные данные в EPROM
9.3 МИГАЕТ Иммобилайзер
9.4 светится постоянно Пусковое реле
9.5 светится постоянно Ошибочная процедура остановки двигателя
Ремонт кпп zf, как отремонтировать робот КПП Eurotronic, ZF-AS Eurotronic, для IVECO, DAF, MAN
2011-2017 © Олег Дудник
Выложил админ: по просьбе Вадима
Описание: Габариты следующие, длина — 3466, ширина — 1100, высота — 1637 мм. Колесная база составляет 2749 мм. Дорожный просвет 132 мм. Автомобиль оснащается гибридным силовым агрегатом. 4—цилиндровый двигатель оборудован системой обеспечивающей выходную мощность мотора. На каждый цилиндр приходится по 4 клапана. Диаметр одного цилиндра составляет 76 мм, ход поршня – 70 мм. Коленчатый вал двигателя разгоняется до 4000 оборотов в минуту. Максимальный крутящий момент удерживается вплоть до 5000 оборотов в минуту.
Cмотрите ВИДЕО про iveco ошибка ecm 99.
Оценка автовладельца по имени Вениамин : Комфортная, в городке шустрая, расход небольшой емкая я рыбак и лодка и мотор и снасти на троих влазят, подвеска мягенькая приятная, управление отличное
Категория: Ремонт своими руками
Дата выхода: 11. 12. 2019 года
Смех в теме: Сперва они говорят чувствовать себя как дома, а потом удивляются, почему ты закрываешься в ванной и рыдаешь.
Случилось неприятность ехал домой с грузом по обычным российским дорогам около 40км(больше совесть не позволяла) попал пару кочек и заглох…
Осмотрел все не нашел обрыва начал искать в интернете что это за чудеса такие(ошибки 97-100).
Нашел от тяжелых грузовых машин(Стралис Треккер Еврокарго) у них это ошибки надува и и расположение распредвала. Ок снял датчик давления(он же температуры воздуха)на впускном коллекторе
Прочистили мы его и промыли салярой.
Потом сняли датчик распредвала
и вуаля все работает ошибок нет…
Нету фото ремонта так как времени небыло делать их.
И да забыл сказать старый хозяин сказал что их никогда не менял и не трогал видимо моя очередь их менять. Пока расходы были на саляру для промывки
На этой страничке вы можете узнать коды неисправностей КПП евротроник для IVECO
Расшифровка показаний дисплея:
Расшифровка кодов неисправностей КПП евротроник для IVECO
КОД контакт ДИСПЛЕЙ ОПИСАНИЕ
Расшифровка мигающих кодов EDC MS6.2 SW 5.X
Мигающий код Контрольная лампа EDC Неисправность
ДВИГАТЕЛЬ
2.1 ВЫКЛЮЧЕНА Датчик температуры охлаждающей ‘жидкости
2.2 ВЫКЛЮЧЕНА Датчик температуры воздуха
2.3 ВЫКЛЮЧЕНА Датчик температуры топлива
2.4 светится постоянно Датчик давления наддува
2.5 ВЫКЛЮЧЕНА Датчик атмосферного давления (внутри блока управления)
2.6 светится постоянно Сигнал датчика моторного тормоза
3.5 ВЫКЛЮЧЕНА Напряжение аккумулятора
ТУРБИНА
4.1 ВЫКЛЮЧЕНА Датчик давления в приводе турбины
4.2 светится постоянно Датчик частоты вращения турбины
4.3 светится постоянно Повышенная частота вращения турбины
4.4 светится постоянно Управление турбиной (механическая неисправность)
4.5 светится постоянно Электромагнитный клапан турбины с изменяемой геометрией
4.6 МИГАЕТ Электромагнитный клапан управления моторным тормозом
ФОРСУНКИ
5.1 светится постоянно Неисправность форсунки цилиндра 1
5.2 светится постоянно Неисправность форсунки цилиндра 2
5.3 светится постоянно Неисправность форсунки цилиндра 3
5.4 светится постоянно Неисправность форсунки цилиндра 4
5.5 светится постоянно Неисправность форсунки цилиндра 5
5.6 светится постоянно Неисправность форсунки цилиндра 6
ДАТЧИКИ ЧАСТОТЫ ВРАЩЕНИЯ ДВИГАТЕЛЯ
6.1 светится постоянно Датчик на маховике
6.2 светится постоянно Датчик на шестерне газораспределительного механизма
6.4 МИГАЕТ Повышенная частота вращения двигателя
БЛОК УПРАВЛЕНИЯ
9.1 МИГАЕТ Неисправен блок управления
9.2 светится постоянно Ошибочные данные в EPROM
9.3 МИГАЕТ Иммобилайзер
9.4 светится постоянно Пусковое реле
9.5 светится постоянно Ошибочная процедура остановки двигателя
Ремонт кпп zf, как отремонтировать робот КПП Eurotronic, ZF-AS Eurotronic, для IVECO, DAF, MAN
2011-2017 © Олег Дудник
Источники:
https://avsu-pitanie. ru/info/ecm-99-oshibka-iveko/