Код ошибки | Описание ошибки |
---|---|
F2/F7 | Нет подачи электричества к заварнику |
F5 | Заварник отключен |
F6 | Затрудненная работа варочного модуля |
F26/F36/F46 | Сбой кофемолки |
F87 | Поврежден датчик бойлера |
F88 | Перегрев бойлера |
F89 | Ошибка времени нагрева бойлера |
F130 | Общий сбой |
F149 | Общий сбой напряжения |
F161 | Сбой счетчика воды во время варки |
F162 | Сбой счетчика воды во время очистки |
F163 | Ошибка подачи воды при теплой промывке |
F164 | Сбой счетчика воды во время дозации горячей воды |
F165 | Сбой счетчика воды во время дозации шоколада |
F166 | Сбой счетчика воды во время декафината |
F167 | Сбой счетчика воды во время декальцинации |
F186 | Перерыв во время парового заполнения бойлера |
F187 | Поврежден датчик парового бойлера |
F188 | Перегрев бойлера |
F189 | Ошибка времени нагрева парового котла |
- Manuals
- Brands
- WMF Manuals
- Coffee Maker
- Presto
- Service manual
-
Contents
-
Table of Contents
-
Bookmarks
Quick Links
coffee wakes up the world
Service Manual
Coffee Machine
English
Series 1400 Edition 11.2011
Related Manuals for WMF presto
Summary of Contents for WMF presto
-
Page 1
coffee wakes up the world Service Manual Coffee Machine English Series 1400 Edition 11.2011… -
Page 2: Table Of Contents
Valves Submenu SBHWB group (steam boiler and hot water boiler) Submenu control elements Current supply Backup battery Display illumination 4.10 Grounds container 4.11 Fan 16 4.12 Power status 4.13 Submenu choc dispenser / topping WMF presto Service manual edition 11/2011…
-
Page 3: FactoryService/Customer Menu
(Service level 2) …………. 34 10.3 Safe&are (Revision) WMF presto Service manual edition 11/2011…
-
Page 4: Customer Setup
™ Enter service point (only possible with “KonfigTool”). ™ Save data Defaults Customer Service ™ Backup machine data on laptop Additional settings for recipes after the service PIN is entered WMF presto Service manual edition 11/2011…
-
Page 5: Software Service Info
Where is cleaning info displayed? • Time elapsed since last cleaning care info cleaning (how long since last cleaning) • Last 100 cleaning operations with date and time care report WMF presto Service manual edition 11/2011…
-
Page 6: Software Machine Data
On these three displays all possible service actions are listed. They can be looked at and can be reset if carried out. Brewings since last customer check-up /Brewings to Customer check-up Date of next Customer check-up (MM.JJJJ). The customer check-up can be reset only here. WMF presto Service manual edition 11/2011…
-
Page 7: Temperature Submenu
Setting range 80 to 100°C, default 96° C Setting range 110 to 130° C, default 127° C Changing the steam boiler temperature leads to great changes in the dosage of milk and milk foam. Changes are not recommended. WMF presto Service manual edition 11/2011…
-
Page 8: Submenu Cleaning
Submenu access control The settings correspond to the default of the previous standard setting. However, they can now be changed / assigned independently of each other. WMF presto Service manual edition 11/2011…
-
Page 9: Maintenance Messages In Key Operator Mode
Configuration of grinders is registered automatically (see chapter portioner). Configuration of powder portioner is registered automatically (see chapter portioner). See chapter engineering, portioner Heating capacity can be changed as required. in the training manual WMF presto Service manual edition 11/2011…
-
Page 10: FactoryService/Customer Menu
Option Aquaflex / technical insert (mobile station) See chapter Boiler water systems can be selected. See chapter drip tray in the training manual Drain of drip tray must be correctly adjusted manually. Part 2 Engineering WMF presto Service manual edition 11/2011…
-
Page 11
Decaf must be set manually. Summertime automatic change to daylight saving time can See user manual be activated. Factory service/customer menu 6 Option Plug&Clean existant? Accept Option Plug&Clean can be activated Safety queries follow acceptance. WMF presto Service manual edition 11/2011… -
Page 12: Additional Setting Options Via Laptop (Konfigtool)
WMF presto Service manual edition 11/2011…
-
Page 13: Page Maintenance Dates
WMF presto Service Manual Page maintenance dates • Contact data of service technician with phone number Page PIN • Block menu items • Set accounting of unit numbers to “not deletable” Page grounds container • Set capacity WMF presto Service manual edition 11/2011…
-
Page 14: Software Components Test
Current (mA): Value during portioning procedure is displayed During the test the grounds container must be in position and the adjustable screen closed as the brewer receives the coffee powder during the test and dumps it afterwards. WMF presto Service manual edition 11/2011…
-
Page 15: Valves
Beverage button LEDs are subsequently addressed Test beverage buttons by pushing them Test touch fields on the display by touching them Current supply Switch the 24/30 V circuits on and off from the mains. WMF presto Service manual edition 11/2011…
-
Page 16: Backup Battery
Test of function and current consumption 4.12 Power status Report “power failure” to the control unit 4.13 Submenu choc dispenser / topping Test choc valve Test the portioner, the choc valve is also addressed Test mixer motor WMF presto Service manual edition 11/2011…
-
Page 17: Software Service Routines
In this case cleaning or descaling must be repeated. The reset of the customer settings program is treated in the same way by the software, however does not reset the cleaning and descaling obligations. WMF presto Service manual edition 11/2011…
-
Page 18: Idling Current Grinder
Without de-aerating via this routine (e.g. following replacement) a boiler cannot be filled against an air cushion inside. WMF presto Service manual edition 11/2011…
-
Page 19: Exchanging Control Battery At F 157
Descaling Constant water supply: see User Manual Care External tank / technical group: see Info letter 2011-33 5.10 Filter replacement The same function as in the customer care menu. WMF presto Service manual edition 11/2011…
-
Page 20: Beverage Data
Page customergeneral item pretreatment: • User-defined pretreatment setting possible (Pressing, pre-infusion, wet pressing, warm rinse) Page customergeneral item variety text: • Random variety text Page general: • Multiple brewing (e.g. for a pot of coffee) WMF presto Service manual edition 11/2011…
-
Page 21: Error Messages And Events
After 15,000 brewings or 1 With machines with constant year. water connection. c h a n g e f i l t e r After 30,000 brewings or With water tank machines. 2 years. After 6 years. WMF presto Service manual edition 11/2011…
-
Page 22: Error List
F36 Current malfunction √ √ Portioner 2 F46 Current malfunction √ √ not implemented not implemented Portioner 3 F87 Boiler sensor √ √ damaged F88 boiler excess √ √ temperature F89 boiler heating time √ √ WMF presto Service manual edition 11/2011…
-
Page 23
166 F166 flowmeter √ √ malfunction during DK feeding 167 F167 flowmeter √ √ malfunction during descaling 186 F186 timeout during √ √ steam boiler filling 187 F187 Steam boiler sensor √ √ damage WMF presto Service manual edition 11/2011… -
Page 24
√ √ brewing-valve not detected 9258 Auto detect malfunction: √ √ Oscillating pump not detected 9259 Auto detect malfunction: √ √ Release valve not detected 9260 Auto detect malfunction: √ √ Fan not detected WMF presto Service manual edition 11/2011… -
Page 25
9290 MDB communication √ √ 290 9290 error banknote reader 9291 24 V are switched off and √ √ 291 9291 then on again (reset for MDB equipment on 24 V) WMF presto Service manual edition 11/2011… -
Page 26: Reasons For Reset
RST_k_INBETRIEB Reset after filter rinse RST_k_FILTERSP Standby causes Reason Comment not used RESET Reset consequences PWS OFF Switching off-on Service mode Enter or exit Cleaning with switch off Cleaning with switch off not used WMF presto Service manual edition 11/2011…
-
Page 27: Mechanical Settings
The replacement grinder is prepared for installation in portioner position 1 and 3 (far right and far left). For installation at portioner position 2 (center) the auger (grinder fineness setting) and is bearings must be reassembled to the intended position. WMF presto Service manual edition 11/2011…
-
Page 28: Setting Pressure Reducer
™ Start test on laptop Supply valve opens ™ Read pressure on pressure gauge. ™ Set pressure to 1.8 bar at pressure reducer. ™ Finish test ™ Dismantle setting equipment and remove auxiliary nipple. ™ Replace filler cap. WMF presto Service manual edition 11/2011…
-
Page 29: Milk Nozzles
WMF presto Service Manual Milk nozzles WMF presto Service manual edition 11/2011…
-
Page 30: Maintenance Concepts 15.000 Brewings
O-ring 37 x 3,5 mm 33.7006.5190 Milk hose: Mixer hose 20 cm 00.0048.0064 20cm Milk hose 100 cm 00.0048.4948 100cm Milk nozzle 1,3 mm green 33.2317.8000 Milk nozzle 1,4 mm white 33.9516.9000 Milk nozzle 3,0 mm beige 33.20.46.0100 WMF presto Service manual edition 11/2011…
-
Page 31: Customer Check-Up Routine
33.2295.6000 Fuse 33.1471.9000 Plug-and-socket connection 33.1448.0000 Brewer cpl. 33.2823.6099 Boiler: SV 16 bar Boiler 33.2297.0099 Cable clip 33.0649.3000 Brewing valve, Hot water dispensing 33.2273.9000 valve Release valve: Release valve 33.2274.5000 CPU: Battery 33.2263.3000 Tank: WMF presto Service manual edition 11/2011…
-
Page 32
Order number Amount Combi spout: Milk foamer cpl. 33.2259.8000 Y-piece 33.2266.6000 Steam nozzle cpl. 33.2824.6000 Ventilating system: 33.1662.1200 Branch pipe 45° 33.2123.8000 Hose 60cm 00.0048.0042 60cm Brewer: Connector 33.2295.6000 Fuse 33.1471.9000 Plug-and-socket connection 33.1448.0000 Boiler: WMF presto Service manual edition 11/2011… -
Page 33
Brewing valve, Hot water dispensing 33.2273.9000 valve Release valve: Release valve 33.2274.5000 CPU: Battery 33.2263.3000 Tank: O-ring 7,65 x 1,78 mm 33.0396.1000 Grease: Grease Molykote 33.2179.9000 After every 30.000 brewings, the brewer 33.2823.6099 has to be exchanged completely! WMF presto Service manual edition 11/2011… -
Page 34: Service/Maintenance Routine 2/30.000
™ Replace mixer (part 6) and fit mixer spout ™ Replace mixer valve and mixer delivery ™ Settings Additional work for worn grinding-disks ™ Replace grinding-disks ™ Settings 10.3 Safe&are (Revision) See technical Info letter 2011-06 Safe&Care. WMF presto Service manual edition 11/2011…
- Manuals
- Brands
- WMF Manuals
- Coffee Maker
- Presto
- Service manual
-
Contents
-
Table of Contents
-
Bookmarks
Quick Links
coffee wakes up the world
Service Manual
Coffee Machine
English
Series 1400 Edition 11.2011
Related Manuals for WMF presto
Summary of Contents for WMF presto
-
Page 1
coffee wakes up the world Service Manual Coffee Machine English Series 1400 Edition 11.2011… -
Page 2: Table Of Contents
Valves Submenu SBHWB group (steam boiler and hot water boiler) Submenu control elements Current supply Backup battery Display illumination 4.10 Grounds container 4.11 Fan 16 4.12 Power status 4.13 Submenu choc dispenser / topping WMF presto Service manual edition 11/2011…
-
Page 3: FactoryService/Customer Menu
(Service level 2) …………. 34 10.3 Safe&are (Revision) WMF presto Service manual edition 11/2011…
-
Page 4: Customer Setup
™ Enter service point (only possible with “KonfigTool”). ™ Save data Defaults Customer Service ™ Backup machine data on laptop Additional settings for recipes after the service PIN is entered WMF presto Service manual edition 11/2011…
-
Page 5: Software Service Info
Where is cleaning info displayed? • Time elapsed since last cleaning care info cleaning (how long since last cleaning) • Last 100 cleaning operations with date and time care report WMF presto Service manual edition 11/2011…
-
Page 6: Software Machine Data
On these three displays all possible service actions are listed. They can be looked at and can be reset if carried out. Brewings since last customer check-up /Brewings to Customer check-up Date of next Customer check-up (MM.JJJJ). The customer check-up can be reset only here. WMF presto Service manual edition 11/2011…
-
Page 7: Temperature Submenu
Setting range 80 to 100°C, default 96° C Setting range 110 to 130° C, default 127° C Changing the steam boiler temperature leads to great changes in the dosage of milk and milk foam. Changes are not recommended. WMF presto Service manual edition 11/2011…
-
Page 8: Submenu Cleaning
Submenu access control The settings correspond to the default of the previous standard setting. However, they can now be changed / assigned independently of each other. WMF presto Service manual edition 11/2011…
-
Page 9: Maintenance Messages In Key Operator Mode
Configuration of grinders is registered automatically (see chapter portioner). Configuration of powder portioner is registered automatically (see chapter portioner). See chapter engineering, portioner Heating capacity can be changed as required. in the training manual WMF presto Service manual edition 11/2011…
-
Page 10: FactoryService/Customer Menu
Option Aquaflex / technical insert (mobile station) See chapter Boiler water systems can be selected. See chapter drip tray in the training manual Drain of drip tray must be correctly adjusted manually. Part 2 Engineering WMF presto Service manual edition 11/2011…
-
Page 11
Decaf must be set manually. Summertime automatic change to daylight saving time can See user manual be activated. Factory service/customer menu 6 Option Plug&Clean existant? Accept Option Plug&Clean can be activated Safety queries follow acceptance. WMF presto Service manual edition 11/2011… -
Page 12: Additional Setting Options Via Laptop (Konfigtool)
WMF presto Service manual edition 11/2011…
-
Page 13: Page Maintenance Dates
WMF presto Service Manual Page maintenance dates • Contact data of service technician with phone number Page PIN • Block menu items • Set accounting of unit numbers to “not deletable” Page grounds container • Set capacity WMF presto Service manual edition 11/2011…
-
Page 14: Software Components Test
Current (mA): Value during portioning procedure is displayed During the test the grounds container must be in position and the adjustable screen closed as the brewer receives the coffee powder during the test and dumps it afterwards. WMF presto Service manual edition 11/2011…
-
Page 15: Valves
Beverage button LEDs are subsequently addressed Test beverage buttons by pushing them Test touch fields on the display by touching them Current supply Switch the 24/30 V circuits on and off from the mains. WMF presto Service manual edition 11/2011…
-
Page 16: Backup Battery
Test of function and current consumption 4.12 Power status Report “power failure” to the control unit 4.13 Submenu choc dispenser / topping Test choc valve Test the portioner, the choc valve is also addressed Test mixer motor WMF presto Service manual edition 11/2011…
-
Page 17: Software Service Routines
In this case cleaning or descaling must be repeated. The reset of the customer settings program is treated in the same way by the software, however does not reset the cleaning and descaling obligations. WMF presto Service manual edition 11/2011…
-
Page 18: Idling Current Grinder
Without de-aerating via this routine (e.g. following replacement) a boiler cannot be filled against an air cushion inside. WMF presto Service manual edition 11/2011…
-
Page 19: Exchanging Control Battery At F 157
Descaling Constant water supply: see User Manual Care External tank / technical group: see Info letter 2011-33 5.10 Filter replacement The same function as in the customer care menu. WMF presto Service manual edition 11/2011…
-
Page 20: Beverage Data
Page customergeneral item pretreatment: • User-defined pretreatment setting possible (Pressing, pre-infusion, wet pressing, warm rinse) Page customergeneral item variety text: • Random variety text Page general: • Multiple brewing (e.g. for a pot of coffee) WMF presto Service manual edition 11/2011…
-
Page 21: Error Messages And Events
After 15,000 brewings or 1 With machines with constant year. water connection. c h a n g e f i l t e r After 30,000 brewings or With water tank machines. 2 years. After 6 years. WMF presto Service manual edition 11/2011…
-
Page 22: Error List
F36 Current malfunction √ √ Portioner 2 F46 Current malfunction √ √ not implemented not implemented Portioner 3 F87 Boiler sensor √ √ damaged F88 boiler excess √ √ temperature F89 boiler heating time √ √ WMF presto Service manual edition 11/2011…
-
Page 23
166 F166 flowmeter √ √ malfunction during DK feeding 167 F167 flowmeter √ √ malfunction during descaling 186 F186 timeout during √ √ steam boiler filling 187 F187 Steam boiler sensor √ √ damage WMF presto Service manual edition 11/2011… -
Page 24
√ √ brewing-valve not detected 9258 Auto detect malfunction: √ √ Oscillating pump not detected 9259 Auto detect malfunction: √ √ Release valve not detected 9260 Auto detect malfunction: √ √ Fan not detected WMF presto Service manual edition 11/2011… -
Page 25
9290 MDB communication √ √ 290 9290 error banknote reader 9291 24 V are switched off and √ √ 291 9291 then on again (reset for MDB equipment on 24 V) WMF presto Service manual edition 11/2011… -
Page 26: Reasons For Reset
RST_k_INBETRIEB Reset after filter rinse RST_k_FILTERSP Standby causes Reason Comment not used RESET Reset consequences PWS OFF Switching off-on Service mode Enter or exit Cleaning with switch off Cleaning with switch off not used WMF presto Service manual edition 11/2011…
-
Page 27: Mechanical Settings
The replacement grinder is prepared for installation in portioner position 1 and 3 (far right and far left). For installation at portioner position 2 (center) the auger (grinder fineness setting) and is bearings must be reassembled to the intended position. WMF presto Service manual edition 11/2011…
-
Page 28: Setting Pressure Reducer
™ Start test on laptop Supply valve opens ™ Read pressure on pressure gauge. ™ Set pressure to 1.8 bar at pressure reducer. ™ Finish test ™ Dismantle setting equipment and remove auxiliary nipple. ™ Replace filler cap. WMF presto Service manual edition 11/2011…
-
Page 29: Milk Nozzles
WMF presto Service Manual Milk nozzles WMF presto Service manual edition 11/2011…
-
Page 30: Maintenance Concepts 15.000 Brewings
O-ring 37 x 3,5 mm 33.7006.5190 Milk hose: Mixer hose 20 cm 00.0048.0064 20cm Milk hose 100 cm 00.0048.4948 100cm Milk nozzle 1,3 mm green 33.2317.8000 Milk nozzle 1,4 mm white 33.9516.9000 Milk nozzle 3,0 mm beige 33.20.46.0100 WMF presto Service manual edition 11/2011…
-
Page 31: Customer Check-Up Routine
33.2295.6000 Fuse 33.1471.9000 Plug-and-socket connection 33.1448.0000 Brewer cpl. 33.2823.6099 Boiler: SV 16 bar Boiler 33.2297.0099 Cable clip 33.0649.3000 Brewing valve, Hot water dispensing 33.2273.9000 valve Release valve: Release valve 33.2274.5000 CPU: Battery 33.2263.3000 Tank: WMF presto Service manual edition 11/2011…
-
Page 32
Order number Amount Combi spout: Milk foamer cpl. 33.2259.8000 Y-piece 33.2266.6000 Steam nozzle cpl. 33.2824.6000 Ventilating system: 33.1662.1200 Branch pipe 45° 33.2123.8000 Hose 60cm 00.0048.0042 60cm Brewer: Connector 33.2295.6000 Fuse 33.1471.9000 Plug-and-socket connection 33.1448.0000 Boiler: WMF presto Service manual edition 11/2011… -
Page 33
Brewing valve, Hot water dispensing 33.2273.9000 valve Release valve: Release valve 33.2274.5000 CPU: Battery 33.2263.3000 Tank: O-ring 7,65 x 1,78 mm 33.0396.1000 Grease: Grease Molykote 33.2179.9000 After every 30.000 brewings, the brewer 33.2823.6099 has to be exchanged completely! WMF presto Service manual edition 11/2011… -
Page 34: Service/Maintenance Routine 2/30.000
™ Replace mixer (part 6) and fit mixer spout ™ Replace mixer valve and mixer delivery ™ Settings Additional work for worn grinding-disks ™ Replace grinding-disks ™ Settings 10.3 Safe&are (Revision) See technical Info letter 2011-06 Safe&Care. WMF presto Service manual edition 11/2011…
- Manuals
- Brands
- WMF Manuals
- Coffee Maker
- Presto
- Service manual
-
Contents
-
Table of Contents
-
Bookmarks
Quick Links
coffee wakes up the world
Service Manual
Coffee Machine
English
Series 1400 Edition 11.2011
Related Manuals for WMF presto
Summary of Contents for WMF presto
-
Page 1
coffee wakes up the world Service Manual Coffee Machine English Series 1400 Edition 11.2011… -
Page 2: Table Of Contents
Valves Submenu SBHWB group (steam boiler and hot water boiler) Submenu control elements Current supply Backup battery Display illumination 4.10 Grounds container 4.11 Fan 16 4.12 Power status 4.13 Submenu choc dispenser / topping WMF presto Service manual edition 11/2011…
-
Page 3: FactoryService/Customer Menu
(Service level 2) …………. 34 10.3 Safe&are (Revision) WMF presto Service manual edition 11/2011…
-
Page 4: Customer Setup
™ Enter service point (only possible with “KonfigTool”). ™ Save data Defaults Customer Service ™ Backup machine data on laptop Additional settings for recipes after the service PIN is entered WMF presto Service manual edition 11/2011…
-
Page 5: Software Service Info
Where is cleaning info displayed? • Time elapsed since last cleaning care info cleaning (how long since last cleaning) • Last 100 cleaning operations with date and time care report WMF presto Service manual edition 11/2011…
-
Page 6: Software Machine Data
On these three displays all possible service actions are listed. They can be looked at and can be reset if carried out. Brewings since last customer check-up /Brewings to Customer check-up Date of next Customer check-up (MM.JJJJ). The customer check-up can be reset only here. WMF presto Service manual edition 11/2011…
-
Page 7: Temperature Submenu
Setting range 80 to 100°C, default 96° C Setting range 110 to 130° C, default 127° C Changing the steam boiler temperature leads to great changes in the dosage of milk and milk foam. Changes are not recommended. WMF presto Service manual edition 11/2011…
-
Page 8: Submenu Cleaning
Submenu access control The settings correspond to the default of the previous standard setting. However, they can now be changed / assigned independently of each other. WMF presto Service manual edition 11/2011…
-
Page 9: Maintenance Messages In Key Operator Mode
Configuration of grinders is registered automatically (see chapter portioner). Configuration of powder portioner is registered automatically (see chapter portioner). See chapter engineering, portioner Heating capacity can be changed as required. in the training manual WMF presto Service manual edition 11/2011…
-
Page 10: FactoryService/Customer Menu
Option Aquaflex / technical insert (mobile station) See chapter Boiler water systems can be selected. See chapter drip tray in the training manual Drain of drip tray must be correctly adjusted manually. Part 2 Engineering WMF presto Service manual edition 11/2011…
-
Page 11
Decaf must be set manually. Summertime automatic change to daylight saving time can See user manual be activated. Factory service/customer menu 6 Option Plug&Clean existant? Accept Option Plug&Clean can be activated Safety queries follow acceptance. WMF presto Service manual edition 11/2011… -
Page 12: Additional Setting Options Via Laptop (Konfigtool)
WMF presto Service manual edition 11/2011…
-
Page 13: Page Maintenance Dates
WMF presto Service Manual Page maintenance dates • Contact data of service technician with phone number Page PIN • Block menu items • Set accounting of unit numbers to “not deletable” Page grounds container • Set capacity WMF presto Service manual edition 11/2011…
-
Page 14: Software Components Test
Current (mA): Value during portioning procedure is displayed During the test the grounds container must be in position and the adjustable screen closed as the brewer receives the coffee powder during the test and dumps it afterwards. WMF presto Service manual edition 11/2011…
-
Page 15: Valves
Beverage button LEDs are subsequently addressed Test beverage buttons by pushing them Test touch fields on the display by touching them Current supply Switch the 24/30 V circuits on and off from the mains. WMF presto Service manual edition 11/2011…
-
Page 16: Backup Battery
Test of function and current consumption 4.12 Power status Report “power failure” to the control unit 4.13 Submenu choc dispenser / topping Test choc valve Test the portioner, the choc valve is also addressed Test mixer motor WMF presto Service manual edition 11/2011…
-
Page 17: Software Service Routines
In this case cleaning or descaling must be repeated. The reset of the customer settings program is treated in the same way by the software, however does not reset the cleaning and descaling obligations. WMF presto Service manual edition 11/2011…
-
Page 18: Idling Current Grinder
Without de-aerating via this routine (e.g. following replacement) a boiler cannot be filled against an air cushion inside. WMF presto Service manual edition 11/2011…
-
Page 19: Exchanging Control Battery At F 157
Descaling Constant water supply: see User Manual Care External tank / technical group: see Info letter 2011-33 5.10 Filter replacement The same function as in the customer care menu. WMF presto Service manual edition 11/2011…
-
Page 20: Beverage Data
Page customergeneral item pretreatment: • User-defined pretreatment setting possible (Pressing, pre-infusion, wet pressing, warm rinse) Page customergeneral item variety text: • Random variety text Page general: • Multiple brewing (e.g. for a pot of coffee) WMF presto Service manual edition 11/2011…
-
Page 21: Error Messages And Events
After 15,000 brewings or 1 With machines with constant year. water connection. c h a n g e f i l t e r After 30,000 brewings or With water tank machines. 2 years. After 6 years. WMF presto Service manual edition 11/2011…
-
Page 22: Error List
F36 Current malfunction √ √ Portioner 2 F46 Current malfunction √ √ not implemented not implemented Portioner 3 F87 Boiler sensor √ √ damaged F88 boiler excess √ √ temperature F89 boiler heating time √ √ WMF presto Service manual edition 11/2011…
-
Page 23
166 F166 flowmeter √ √ malfunction during DK feeding 167 F167 flowmeter √ √ malfunction during descaling 186 F186 timeout during √ √ steam boiler filling 187 F187 Steam boiler sensor √ √ damage WMF presto Service manual edition 11/2011… -
Page 24
√ √ brewing-valve not detected 9258 Auto detect malfunction: √ √ Oscillating pump not detected 9259 Auto detect malfunction: √ √ Release valve not detected 9260 Auto detect malfunction: √ √ Fan not detected WMF presto Service manual edition 11/2011… -
Page 25
9290 MDB communication √ √ 290 9290 error banknote reader 9291 24 V are switched off and √ √ 291 9291 then on again (reset for MDB equipment on 24 V) WMF presto Service manual edition 11/2011… -
Page 26: Reasons For Reset
RST_k_INBETRIEB Reset after filter rinse RST_k_FILTERSP Standby causes Reason Comment not used RESET Reset consequences PWS OFF Switching off-on Service mode Enter or exit Cleaning with switch off Cleaning with switch off not used WMF presto Service manual edition 11/2011…
-
Page 27: Mechanical Settings
The replacement grinder is prepared for installation in portioner position 1 and 3 (far right and far left). For installation at portioner position 2 (center) the auger (grinder fineness setting) and is bearings must be reassembled to the intended position. WMF presto Service manual edition 11/2011…
-
Page 28: Setting Pressure Reducer
™ Start test on laptop Supply valve opens ™ Read pressure on pressure gauge. ™ Set pressure to 1.8 bar at pressure reducer. ™ Finish test ™ Dismantle setting equipment and remove auxiliary nipple. ™ Replace filler cap. WMF presto Service manual edition 11/2011…
-
Page 29: Milk Nozzles
WMF presto Service Manual Milk nozzles WMF presto Service manual edition 11/2011…
-
Page 30: Maintenance Concepts 15.000 Brewings
O-ring 37 x 3,5 mm 33.7006.5190 Milk hose: Mixer hose 20 cm 00.0048.0064 20cm Milk hose 100 cm 00.0048.4948 100cm Milk nozzle 1,3 mm green 33.2317.8000 Milk nozzle 1,4 mm white 33.9516.9000 Milk nozzle 3,0 mm beige 33.20.46.0100 WMF presto Service manual edition 11/2011…
-
Page 31: Customer Check-Up Routine
33.2295.6000 Fuse 33.1471.9000 Plug-and-socket connection 33.1448.0000 Brewer cpl. 33.2823.6099 Boiler: SV 16 bar Boiler 33.2297.0099 Cable clip 33.0649.3000 Brewing valve, Hot water dispensing 33.2273.9000 valve Release valve: Release valve 33.2274.5000 CPU: Battery 33.2263.3000 Tank: WMF presto Service manual edition 11/2011…
-
Page 32
Order number Amount Combi spout: Milk foamer cpl. 33.2259.8000 Y-piece 33.2266.6000 Steam nozzle cpl. 33.2824.6000 Ventilating system: 33.1662.1200 Branch pipe 45° 33.2123.8000 Hose 60cm 00.0048.0042 60cm Brewer: Connector 33.2295.6000 Fuse 33.1471.9000 Plug-and-socket connection 33.1448.0000 Boiler: WMF presto Service manual edition 11/2011… -
Page 33
Brewing valve, Hot water dispensing 33.2273.9000 valve Release valve: Release valve 33.2274.5000 CPU: Battery 33.2263.3000 Tank: O-ring 7,65 x 1,78 mm 33.0396.1000 Grease: Grease Molykote 33.2179.9000 After every 30.000 brewings, the brewer 33.2823.6099 has to be exchanged completely! WMF presto Service manual edition 11/2011… -
Page 34: Service/Maintenance Routine 2/30.000
™ Replace mixer (part 6) and fit mixer spout ™ Replace mixer valve and mixer delivery ™ Settings Additional work for worn grinding-disks ™ Replace grinding-disks ™ Settings 10.3 Safe&are (Revision) See technical Info letter 2011-06 Safe&Care. WMF presto Service manual edition 11/2011…
- Manuals
- Brands
- WMF Manuals
- Coffee Maker
- Presto
- Service manual
-
Contents
-
Table of Contents
-
Bookmarks
Quick Links
coffee wakes up the world
Service Manual
Coffee Machine
English
Series 1400 Edition 11.2011
Related Manuals for WMF presto
Summary of Contents for WMF presto
-
Page 1
coffee wakes up the world Service Manual Coffee Machine English Series 1400 Edition 11.2011… -
Page 2: Table Of Contents
Valves Submenu SBHWB group (steam boiler and hot water boiler) Submenu control elements Current supply Backup battery Display illumination 4.10 Grounds container 4.11 Fan 16 4.12 Power status 4.13 Submenu choc dispenser / topping WMF presto Service manual edition 11/2011…
-
Page 3: FactoryService/Customer Menu
(Service level 2) …………. 34 10.3 Safe&are (Revision) WMF presto Service manual edition 11/2011…
-
Page 4: Customer Setup
™ Enter service point (only possible with “KonfigTool”). ™ Save data Defaults Customer Service ™ Backup machine data on laptop Additional settings for recipes after the service PIN is entered WMF presto Service manual edition 11/2011…
-
Page 5: Software Service Info
Where is cleaning info displayed? • Time elapsed since last cleaning care info cleaning (how long since last cleaning) • Last 100 cleaning operations with date and time care report WMF presto Service manual edition 11/2011…
-
Page 6: Software Machine Data
On these three displays all possible service actions are listed. They can be looked at and can be reset if carried out. Brewings since last customer check-up /Brewings to Customer check-up Date of next Customer check-up (MM.JJJJ). The customer check-up can be reset only here. WMF presto Service manual edition 11/2011…
-
Page 7: Temperature Submenu
Setting range 80 to 100°C, default 96° C Setting range 110 to 130° C, default 127° C Changing the steam boiler temperature leads to great changes in the dosage of milk and milk foam. Changes are not recommended. WMF presto Service manual edition 11/2011…
-
Page 8: Submenu Cleaning
Submenu access control The settings correspond to the default of the previous standard setting. However, they can now be changed / assigned independently of each other. WMF presto Service manual edition 11/2011…
-
Page 9: Maintenance Messages In Key Operator Mode
Configuration of grinders is registered automatically (see chapter portioner). Configuration of powder portioner is registered automatically (see chapter portioner). See chapter engineering, portioner Heating capacity can be changed as required. in the training manual WMF presto Service manual edition 11/2011…
-
Page 10: FactoryService/Customer Menu
Option Aquaflex / technical insert (mobile station) See chapter Boiler water systems can be selected. See chapter drip tray in the training manual Drain of drip tray must be correctly adjusted manually. Part 2 Engineering WMF presto Service manual edition 11/2011…
-
Page 11
Decaf must be set manually. Summertime automatic change to daylight saving time can See user manual be activated. Factory service/customer menu 6 Option Plug&Clean existant? Accept Option Plug&Clean can be activated Safety queries follow acceptance. WMF presto Service manual edition 11/2011… -
Page 12: Additional Setting Options Via Laptop (Konfigtool)
WMF presto Service manual edition 11/2011…
-
Page 13: Page Maintenance Dates
WMF presto Service Manual Page maintenance dates • Contact data of service technician with phone number Page PIN • Block menu items • Set accounting of unit numbers to “not deletable” Page grounds container • Set capacity WMF presto Service manual edition 11/2011…
-
Page 14: Software Components Test
Current (mA): Value during portioning procedure is displayed During the test the grounds container must be in position and the adjustable screen closed as the brewer receives the coffee powder during the test and dumps it afterwards. WMF presto Service manual edition 11/2011…
-
Page 15: Valves
Beverage button LEDs are subsequently addressed Test beverage buttons by pushing them Test touch fields on the display by touching them Current supply Switch the 24/30 V circuits on and off from the mains. WMF presto Service manual edition 11/2011…
-
Page 16: Backup Battery
Test of function and current consumption 4.12 Power status Report “power failure” to the control unit 4.13 Submenu choc dispenser / topping Test choc valve Test the portioner, the choc valve is also addressed Test mixer motor WMF presto Service manual edition 11/2011…
-
Page 17: Software Service Routines
In this case cleaning or descaling must be repeated. The reset of the customer settings program is treated in the same way by the software, however does not reset the cleaning and descaling obligations. WMF presto Service manual edition 11/2011…
-
Page 18: Idling Current Grinder
Without de-aerating via this routine (e.g. following replacement) a boiler cannot be filled against an air cushion inside. WMF presto Service manual edition 11/2011…
-
Page 19: Exchanging Control Battery At F 157
Descaling Constant water supply: see User Manual Care External tank / technical group: see Info letter 2011-33 5.10 Filter replacement The same function as in the customer care menu. WMF presto Service manual edition 11/2011…
-
Page 20: Beverage Data
Page customergeneral item pretreatment: • User-defined pretreatment setting possible (Pressing, pre-infusion, wet pressing, warm rinse) Page customergeneral item variety text: • Random variety text Page general: • Multiple brewing (e.g. for a pot of coffee) WMF presto Service manual edition 11/2011…
-
Page 21: Error Messages And Events
After 15,000 brewings or 1 With machines with constant year. water connection. c h a n g e f i l t e r After 30,000 brewings or With water tank machines. 2 years. After 6 years. WMF presto Service manual edition 11/2011…
-
Page 22: Error List
F36 Current malfunction √ √ Portioner 2 F46 Current malfunction √ √ not implemented not implemented Portioner 3 F87 Boiler sensor √ √ damaged F88 boiler excess √ √ temperature F89 boiler heating time √ √ WMF presto Service manual edition 11/2011…
-
Page 23
166 F166 flowmeter √ √ malfunction during DK feeding 167 F167 flowmeter √ √ malfunction during descaling 186 F186 timeout during √ √ steam boiler filling 187 F187 Steam boiler sensor √ √ damage WMF presto Service manual edition 11/2011… -
Page 24
√ √ brewing-valve not detected 9258 Auto detect malfunction: √ √ Oscillating pump not detected 9259 Auto detect malfunction: √ √ Release valve not detected 9260 Auto detect malfunction: √ √ Fan not detected WMF presto Service manual edition 11/2011… -
Page 25
9290 MDB communication √ √ 290 9290 error banknote reader 9291 24 V are switched off and √ √ 291 9291 then on again (reset for MDB equipment on 24 V) WMF presto Service manual edition 11/2011… -
Page 26: Reasons For Reset
RST_k_INBETRIEB Reset after filter rinse RST_k_FILTERSP Standby causes Reason Comment not used RESET Reset consequences PWS OFF Switching off-on Service mode Enter or exit Cleaning with switch off Cleaning with switch off not used WMF presto Service manual edition 11/2011…
-
Page 27: Mechanical Settings
The replacement grinder is prepared for installation in portioner position 1 and 3 (far right and far left). For installation at portioner position 2 (center) the auger (grinder fineness setting) and is bearings must be reassembled to the intended position. WMF presto Service manual edition 11/2011…
-
Page 28: Setting Pressure Reducer
™ Start test on laptop Supply valve opens ™ Read pressure on pressure gauge. ™ Set pressure to 1.8 bar at pressure reducer. ™ Finish test ™ Dismantle setting equipment and remove auxiliary nipple. ™ Replace filler cap. WMF presto Service manual edition 11/2011…
-
Page 29: Milk Nozzles
WMF presto Service Manual Milk nozzles WMF presto Service manual edition 11/2011…
-
Page 30: Maintenance Concepts 15.000 Brewings
O-ring 37 x 3,5 mm 33.7006.5190 Milk hose: Mixer hose 20 cm 00.0048.0064 20cm Milk hose 100 cm 00.0048.4948 100cm Milk nozzle 1,3 mm green 33.2317.8000 Milk nozzle 1,4 mm white 33.9516.9000 Milk nozzle 3,0 mm beige 33.20.46.0100 WMF presto Service manual edition 11/2011…
-
Page 31: Customer Check-Up Routine
33.2295.6000 Fuse 33.1471.9000 Plug-and-socket connection 33.1448.0000 Brewer cpl. 33.2823.6099 Boiler: SV 16 bar Boiler 33.2297.0099 Cable clip 33.0649.3000 Brewing valve, Hot water dispensing 33.2273.9000 valve Release valve: Release valve 33.2274.5000 CPU: Battery 33.2263.3000 Tank: WMF presto Service manual edition 11/2011…
-
Page 32
Order number Amount Combi spout: Milk foamer cpl. 33.2259.8000 Y-piece 33.2266.6000 Steam nozzle cpl. 33.2824.6000 Ventilating system: 33.1662.1200 Branch pipe 45° 33.2123.8000 Hose 60cm 00.0048.0042 60cm Brewer: Connector 33.2295.6000 Fuse 33.1471.9000 Plug-and-socket connection 33.1448.0000 Boiler: WMF presto Service manual edition 11/2011… -
Page 33
Brewing valve, Hot water dispensing 33.2273.9000 valve Release valve: Release valve 33.2274.5000 CPU: Battery 33.2263.3000 Tank: O-ring 7,65 x 1,78 mm 33.0396.1000 Grease: Grease Molykote 33.2179.9000 After every 30.000 brewings, the brewer 33.2823.6099 has to be exchanged completely! WMF presto Service manual edition 11/2011… -
Page 34: Service/Maintenance Routine 2/30.000
™ Replace mixer (part 6) and fit mixer spout ™ Replace mixer valve and mixer delivery ™ Settings Additional work for worn grinding-disks ™ Replace grinding-disks ™ Settings 10.3 Safe&are (Revision) See technical Info letter 2011-06 Safe&Care. WMF presto Service manual edition 11/2011…
- Главная
- Коды ошибок кофемашин
Коды ошибок кофемашин Bosch и Siemens
Модели TCA 6xxx TK 6xxxx
Ошибка Error 1 — Машина слишком холодная (< 5 C) Сломан датчик NTC (термодатчик)
Ошибка Error 2 — Нет нагрева термоблока (параблока)
Ошибка Error 5 — Нет нагрева термоблока (параблока)
Ошибка Error 8 — Неисправен заварной механизм. Либо концевик в поддоне, сломана лапка на поддоне.
Fill up pipe-system — заполнить систему
Empty trays — заполнен лоток отработанного кофе, электрическое сопротивление контактов поддона
Trays missing — вставить поддон, электрическое сопротивление контактов поддона
Brewing unit missing — Заварной блок отсутствует или заблокирован
Add beans — нет кофейных зерен в контейнере зерен
Коды ошибок кофемашин Jura
Модели Е10/Е25
Ошибки символьные обозначения:
Пар+открыть кран+поддон+чистка гидросистемы+чистка от накипи+фильтр — Не распознается (Заклинен) заварной механизм
Молотый кофе+открыть кран+поддон+чистка гидросистемы+чистка от накипи+фильтр — Сломан датчик NTC (термодатчик)
Чашка+открыть кран+поддон+чистка гидросистемы+чистка от накипи+фильтр — Короткое замыкание датчика NTC (термодатчик)
Промывка+открыть кран+поддон+чистка гидросистемы+чистка от накипи+фильтр — Нагрев не возможен
Модели Е30/Е40/Е50/Е60/Е65/Scala
Ошибки символьные обозначения:
Мигают 4 зеленых верхние лампочки — Начинается опустошение системы После подачи пара система не была заполнена / повернуть кран
Мигают 4 зеленых верхние лампочки + нижний красный индикатор — Проблемы в распознавании Датчик нагрева поврежден Машина слишком холодная
Мигают пар и чашка — Перегрев
Модели С5
Индикаторы на дисплее мигание:
Индикатор обслуживания + все индикаторы — Дефекты датчика термоблока Невозможно распознавание заварного механизма
Индикатор обслуживания + индикатор чиски гидросистемы — Машина очень горячая для чистки гидросистемы
Индикатор обслуживания + индикатор чиски от накипи — Машина очень горячая для чистки от накипи
Индикатор обслуживания + индикаторы обслуживания (налить воды, засыпать кофе, убрать поддон — Машина очень горячая для промывки
Модели S/X/XS
Ошибка 1 — Датчик температуры нагрева воды, короткое замыкание
Ошибка 2 — Датчик температуры нагрева кофе, сломан
Ошибка 3 — Датчик температуры нагрева пара, короткое замыкание
Ошибка 4 — Датчик температуры нагрева на пар, сломан
Ошибка 5 — Машина слишком холодная, нет нагрева пароблока
Ошибка 6 — Невозможно распознать пара клапан
Ошибка 8 — Неисправен заварной механизм
Модели F/XF/E80
Ошибка 1 — Датчик температуры нагрева, поврежден
Ошибка 5 — Нагрев невозможен
Ошибка 8 — Неисправен заварной механизм
Модели J/Z
Ошибка 1 — Датчик температуры нагрева воды, короткое замыкание
Ошибка 2 — Датчик температуры нагрева кофе, сломан
Ошибка 3 — Датчик температуры нагрева пара, короткое замыкание
Ошибка 4 — Датчик температуры нагрева на пар, сломан
Ошибка 5 — Машина слишком холодная, нет нагрева пароблока
Ошибка 6 — Невозможно распознать пара клапан
Ошибка 7 — Невозможно перемещение мультиклапана
Ошибка 8 — Неисправен заварной механизм
Модели X7/X9
Ошибка 0 — Энкодер
Ошибка 1 — Датчик температуры нагрева воды, короткое замыкание
Ошибка 2 — Датчик температуры нагрева кофе, сломан
Ошибка 3 — Датчик температуры нагрева пара, короткое замыкание
Ошибка 4 — Датчик температуры нагрева на пар, сломан
Ошибка 5 — Машина слишком холодная, нет нагрева пароблока
Ошибка 6 — Невозможно распознать пара клапан
Ошибка 7 — Невозможно перемещение мультиклапана
Ошибка 8 — Неисправен заварной механизм
Коды ошибок кофемашин Krups
Уважаемые Клиенты!
К сожалению, информацию о кодах ошибок кофемашин Krups производитель не разглашает.
Обозначения ошибок на нашем сайте, описаны нашими специалистами на основе собственного опыта, поэтому помимо наших обозначений,
коды ошибок могут также обозначать и другие неисправности.
Ошибка 1 — заблокирован водяной контур (распределитель воды — мотор распределителя, микровыключатель)
Ошибка 5 — заблокирован водяной контур (счетчик воды, помпа, рапределитель)
Ошибка 7 — заблокирована кофемолка
Ошибка 9 — нет нагрева (NTC — сопротивление)
Для моделей krups xp 7240, 7250 возможно произвести самодиагностику кофемашины через меню сервис.
Коды ошибок кофемашин Saeco
Модели Primea, Talea
Ошибка Error 1 — Кофемолка заблокирована
Ошибка Error 2 — Кофемолка заблокирована
Ошибка Error 3 — Заварной механизм заблокирован
Ошибка Error 4 — Заварной механизм заблокирован
Ошибка Error 5 — Водяной контур заблокирован
Ошибка Error 6 — Мультиклапан заблокирован
Ошибка Error 7 — Клапан капучинатора заблокирован
Ошибка Error 8 Powercomm — Неисправность электронной платы
Ошибка Error 9 — Датчик водонагревателя неисправен
Ошибка Error 10 — Датчик водонагревателя неисправен
Ошибка Error 11 — Датчик парового нагревателя неисправен
Ошибка Error 12 — Датчик парового нагревателя неисправен
Ошибка Error 13 — Водонагреватель неисправен
Ошибка Error 14 — Паровой нагреватель неисправен
Коды ошибок кофемашин Saeco Philips
Error 1 / Ошибка 1 — кофемолка заблокирована. (возможные проблемы : заклинены жернова, не верная работы датчика)
Error 3 / Ошибка 3 — заварной блок заблокирован в положении вверх
Error 4 / Ошибка 4 — заварной блок заблокирован в положении вниз
Error 5 / Ошибка 5 — водяной контур заблокирован ( гидросистема не может заполнится водой : неверная работа счетчика воды, неисправен насос, забит бойлер пара)
Error 6 / Ошибка 6 — не работает электромагнитный клапан ( неверная работа эл. магнитного клапана блока приготовления молочных напитков)
Error 10 / Ошибка 10 — неисправен бойлер кофе/термодатчик ( отсутствие сопротивления)
Error 11 / Ошибка 11 — неисправен бойлер кофе/термодатчик ( обрыв цепи)
Error 12 / Ошибка 12 — неисправен бойлер пара/термодатчик ( отсутствие сопротивления)
Error 13 / Ошибка 13 — неисправен бойлер пара/термодатчик ( обрыв цепи)
Error 14 / Ошибка 14 — отсутствует нагрев на кофе (вероятность термостат)
Error 15 / Ошибка 15 — отсутствует нагрев на пар (вероятность термостат)
Error 16 / Ошибка 16 — неисправен редуктор/заварной блок (микровыключатель неправильная работа)
Error 18 / Ошибка 18 — программная ошибка
Error 19 / Ошибка 19 — програмная ошибка / отсутствие эл.контакта (проверить шлейф)
Коды ошибок кофемашин WMF 1200 / дословный перевод
F2 — Brewer without electricity / Пивовар без электричества
F5 — Brewer shutoff / Отключение пивовара
F6 — Brewer over current / Брюэр над течением
F7 — Brewer timeout (no electricity) / Время ожидания пивовара (нет электричества)
F26 — Portioner 1 current malfunction / Неисправность тока Портера 1
F36 — Current malfunction Portioner 2 / Текущая дозатором неисправность 2
F87 — Boiler sensor damaged / Поврежден датчик котла
F88 — boiler excess temperature / избыточная температура котла
F89 — boiler heating time / время нагрева котла
F125 — EEprom missing or defective / EEprom отсутствует или неисправен
F126 — Front panel / CPU Communication error / Ошибка связи передней панели / процессора
F135 — Motor driver error (grinder or brewer motor) / Ошибка водителя мотора (мотор точильщика или винодела)
F161 — flowmeter malfunction during brewing / неисправность расходомера при заваривании
F162 — flowmeter malfunction during cleaning / неисправность расходомера во время очистки
F163 — flowmeter malfunction during checking / неисправность расходомера при проверке
F164 — flowmeter malfunction during hot water dosage / неисправность расходомера при дозировке горячей воды
F165 — flowmeter malfunction during choc dosage / неисправность расходомера при дозировке Чок
F166 — flowmeter malfunction during steam boiler / неисправность расходомера во время парового котла
F167 — flowmeter malfunction during descaling / неисправность расходомера при очистке от накипи
F186 — timeout during steam boiler filling / время ожидания при заполнении парового котла
F187 — Steam boiler sensor damage / Повреждение датчика парового котла
F188 — Excess temperature in steam boiler / Избыточная температура в паровом котле
F189 — Heating-time steam boiler / Боилер пара времени разогрева
Для самостоятельного ремонта кофемашины, Вы можете приобрести запчасти в нашем интернет-магазине
Похожие статьи
57
Руководство по эксплуатации WMF presto!
Сообщения и указания
Код
ошибки
Описание
ошибки
Указания по устранению
88
Бойлер:
перегрев
Выдача напитков временно приостановлена.
Проверить, открыт ли главный кран, наполнена ли
и правильно ли установлена емкость для воды.
Если это не так:
Выключить кофеварочной машины.
Очистка варочного модуля.
w
Уход за машиной w
Очистка варочного модуля, стр. 45
Включить машину и повторить попытку.
(Разблокировка происходит после остывания до нормальной
температуры.)
Выключить машину, дать остыть, затем снова
включить.
89
Бойлер:
ошибка времени
нагрева
Выключить и затем снова включить машину.
161
Ошибка воды:
горячая вода
Между нижеописанными работами необходимо выключать и затем снова
включать машину. Если ошибка не устранена, переходить к следующему
этапу.
Проверить, открыт ли главный кран, наполнена ли
и правильно ли установлена емкость для воды.
Очистка варочного модуля.
w
Уход за машиной w
Очистка варочного модуля, стр. 45
Установить более грубую тонкость помола.
w
Другие настройки w
Установка тонкости помола, стр. 38
Уменьшить качество варки.
w
Настройки w
Рецепты, стр. 29
163
Ошибка воды:
теплая промывка
Между нижеописанными работами необходимо выключать и затем снова
включать машину. Если ошибка не устранена, переходить к следующему
этапу.
Проверить, открыт ли главный кран, наполнена ли
и правильно ли установлена емкость для воды.
Очистка варочного модуля.
w
Уход за машиной w
Очистка варочного модуля, стр. 45
186
Паровой котел:
уровень
Выдача напитков временно приостановлена.
Проверить правильность установки емкости для
кофейной гущи.
Выключить и затем снова включить машину.
188
Ошибка нагрева
Выключить машину, извлечь вилку из сетевой
розетки.
Обратиться в сервис-центр компании WMF.
189
Паровой котел:
ошибка времени
нагрева
Выключить и затем снова включить машину.
WMF presto Service Manual
7.2
See training manual in part 6 chapter troubleshooting
2
F2 Brewer without
electricity
5
F5 Brewer shutoff
6
F6 Brewer over current
7
F7 Brewer timeout (no
electricity)
26
F26 Portioner current
malfunction
36
F36 Current malfunction
Portioner 2
46
F46 Current malfunction
Portioner 3
87
F87 Boiler sensor
damaged
88
F88 boiler excess
temperature
89
F89 boiler heating time
22
√
√
√
√
√
√
√
√
√
√
√
√
√
√ not implemented
√
√
√
√
√
√
WMF presto Service manual edition 08/2014
195
198
253
254
1
3
5
not implemented
40
39
41
Перейти к контенту
Коды ошибок кофемашин WMF
- F2/F7 – нет подачи электричества к заварнику
- F5 – заварник отключен
- F6 – затрудненная работа варочного модуля
- F26/F36/F46 – сбой кофемолки
- F87 – поврежден датчик бойлера
- F88– перегрев бойлера
- F89 – ошибка времени нагрева бойлера
- F130 – общий сбой
- F149 – общий сбой напряжения
- F161 – сбой счетчика воды во время варки
- F162 – сбой счетчика воды во время очистки
- F163 – ошибка подачи воды при теплой промывке
- F164 – сбой счетчика воды во время дозации горячей воды
- F165 – сбой счетчика воды во время дозации шоколада
- F166 — сбой счетчика воды во время декафината
- F167 — сбой счетчика воды во время декальцинации
- F186 — перерыв во время парового заполнения бойлера
- F187 – поврежден датчик парового бойлера
- F188 — перегрев бойлера
- F189 — ошибка времени нагрева парового котла
Дополнительную информацию о поломках кофемашин WMF можно посмотреть здесь:
Устранение неполадки – сложное дело, его лучше доверить профессионалам.
☎️ +375 29 659 33 43 (Viber, Telegram, WhatsApp)
Причины и профилактика поломок
Засорение гидросистемы происходит при некорректном обслуживании. Например, если не производить регулярную декальцинацию, не очищать детали от остатков кофейного масла, не прочищать диспенсер, кофеводы. Также к засорению ведет применение слишком жесткой воды с массой солевых примесей.
Электронные компоненты чаще всего ломаются при значительных сбоях напряжения. Однако такие коды ошибок можно предупредить, если подключать кофемашину через стабилизатор.
Кофемашина может сломаться как при неверном использовании, так и вследствие производственного брака.
Заварное устройство забивается, если нерегулярно промывать клапан под проточной водой, не удалять остатки кофейного масла с кремоклапана, не смазывать прибор.
Более точную информацию о ремонте можно узнать:
ПОЗВОНИТЕ НАМ
ЧТОБЫ ПОЛУЧИТЬ ЛУЧШЕЕ ПРЕДЛОЖЕНИЕ ПРЯМО СЕЙЧАС
57
Руководство по эксплуатации WMF presto!
Сообщения и указания
Код
ошибки
Описание
ошибки
Указания по устранению
88
Бойлер:
перегрев
Выдача напитков временно приостановлена.
Проверить, открыт ли главный кран, наполнена ли
и правильно ли установлена емкость для воды.
Если это не так:
Выключить кофеварочной машины.
Очистка варочного модуля.
w
Уход за машиной w
Очистка варочного модуля, стр. 45
Включить машину и повторить попытку.
(Разблокировка происходит после остывания до нормальной
температуры.)
Выключить машину, дать остыть, затем снова
включить.
89
Бойлер:
ошибка времени
нагрева
Выключить и затем снова включить машину.
161
Ошибка воды:
горячая вода
Между нижеописанными работами необходимо выключать и затем снова
включать машину. Если ошибка не устранена, переходить к следующему
этапу.
Проверить, открыт ли главный кран, наполнена ли
и правильно ли установлена емкость для воды.
Очистка варочного модуля.
w
Уход за машиной w
Очистка варочного модуля, стр. 45
Установить более грубую тонкость помола.
w
Другие настройки w
Установка тонкости помола, стр. 38
Уменьшить качество варки.
w
Настройки w
Рецепты, стр. 29
163
Ошибка воды:
теплая промывка
Между нижеописанными работами необходимо выключать и затем снова
включать машину. Если ошибка не устранена, переходить к следующему
этапу.
Проверить, открыт ли главный кран, наполнена ли
и правильно ли установлена емкость для воды.
Очистка варочного модуля.
w
Уход за машиной w
Очистка варочного модуля, стр. 45
186
Паровой котел:
уровень
Выдача напитков временно приостановлена.
Проверить правильность установки емкости для
кофейной гущи.
Выключить и затем снова включить машину.
188
Ошибка нагрева
Выключить машину, извлечь вилку из сетевой
розетки.
Обратиться в сервис-центр компании WMF.
189
Паровой котел:
ошибка времени
нагрева
Выключить и затем снова включить машину.