Контроллер danfoss dor ошибка

Parameter table

Menu

Menu

Parameter name

code Description

Thermostat

tHE

Main menu for thermostatic settings

Set point

SEt

Set point value

Actual value of setpoint

Set point adjustment ratio

SPr

adjustment = diF * SPr

Differential

diF

Thermostat differential for serving

High Set point

HSE

High limitation of thermostat setpoint in position warm

Low Set point

LSE

Low limitation of thermostat setpoint in position cold

Comp relay action when Tair is between Cut-in and Cut-out at

power-up

Initial cut in

iCi

yES: Cut in the compressor

no: Cut out the compressor

Fan

FAn

Main menu for fan settings

FAo: Fan always on

Fan control method

FCt

SEt: Fan follow compressor by manually settings

Aut: Automatical Fan control

Fan On Delay

Fod

Delay for fan start after compressor cutin

Fan Stop delay

FSd

Delay for fan stop after compressor cutout

Fan On Cycle

FoC

On time for fan during compressor off period

Fan Stop Cycle

FSC

Stop time for fan during compressor off period

Fan Minimum Stop time

FSt

Minimum Stop time for fan protection

Delta T for fan to cut in which the temperature offset comparing

Δt for fan to cut in

FdC

with thermostat cut in temperature

0: Fan stop immediately when door open

Fan delay on door open

Fdt

1~998: delay for fan stop after door open

999: fan keep running all the time during door opening

Light

Lig

Main menu for Light settings

on: Always ON (Button is default to control light for all these options)

Cabinet Light Control Source

CLC

oFF: Always OFF

dor: Door sensor only

Delay to turn off the cabinet light after door close

Light off delay

Lod

0: No delay

Pull Down

Pud Main menu for pull-down settings

Temperature measured by control-sensor that will trigger the

Pull-down Initiate Temperature

Pit

pull-down mode

The duration of the thermostatic operation at pull-down mode

Pull-down Cycling

PCy

The periode will start first time the controller reaches the PCt

Defrost interval during pull-down

Pull-down defrost Interval

Pdi

Over-rules the defrost interval in normal mode

Pull-down duration

Pdd

Max time for pull-down mode from initiated till terminated

The calculated cutout temp for pulldown mustn’t lower than this

Pull-down limit temp

PLt

limit to prevent freezing of product

This progressive temp value is used for calculating cutin temp and

cutout temp for Pull-down mode:

Pull-down reduction temp Δt

Prt

Pulldown-Cutin = NormalCutin — Δt * Hours

Pulldown-Cutout = NormalCutout — Δt * Hours

Defrost

dEF

Main menu for Defrost settings

no: Defrost function is disabled

nAt: Natural defrost. time defrost

Defrost type

dFt

EL: Electrical heater

Hgd: Hot gas defrost

no: Defrost controlled by time

Adaptive defrost

Add

yES: Automatic defrost control activated

Def terminate temp

dtt

Defrost stop temperature

Defrost timer reset temperature

Def reset temp

drt

0-199: normal evaluation between evaporator/air temp and drt

200: disable drt function

Def Min Interval

dii

Minimum Interval between defrost starts

Def Max Interval

dAi

Maximum Interval between defrost starts

Def Min Time

dit

Minimum defrost time

Def Max time

dAt

Maximum defrost time

Drip off time

dot

Drip off delay time

Fan delay after Defrost

Fdd

Delay for fan start after defrost

Fan start temperature after defrost. it’s based on evaporator

Fan start Temp

Ftd

temperature.

This only applies if an evaporator temperature sensor is fitted

Defrost Fan on

dFA

Fan cutin during defrost

no: Elapsed time

Defrost on compressor time

dCt

yES: Accumulated compressor run time

Defrost by compressor

Continuous compressor running can cause defrost

doC

running time

0: Deactived

Defrost start evaporator

dEt

Defrost start trigger for adaptive defrost

temperature

Defrost Δt compare with evporator temperature of first cut out

Defrost Δt

ddt

after defrost to trigger defrost start

Initial Defrost Interval

idi

First time defrost after power-up

Determine defrost or not while startup by relay1 counter

0: Disable idi function

Initial Defrost Duration

idd

1-998: Normal evaluation between idd and relay 1 counter

999: idi is always enabled

Compressor

CoP Main menu for Compressor timer settings

no: No voltage protection

Voltage protection

uPt

yES: Voltage protection activated based on voltage related

settings

Minimum Cutin voltage

uLi

Compressor must not be cut in if power supply goes lower than

Minimum cut-out voltage

uLo

Compressor must be cut out if power supply goes lower than

Maximum supply voltage for the compressor to postpone startup

Maximum voltage

uHi

or stop at

no: No sensor error handling

Sensor Error Type

EHd

SEt: In case of control sensor error, follow error run/stop time

Aut: Automatical Sensor error handling

Error run time

Ert

Run time for compressor in case of control probe error

Error stop time

ESt

Stop time for compressor in case of control probe error

Min Stop time

CSt

Minimum OFF time for compressor

Min run time

Crt

Minimum ON time for compressor

Max Off time

Cot

Maximum OFF time for compressor

Door open delay to stop compressor

Compressor door open delay

Cdd

0: Disable

System resume after door

Fan and Compressor resume after cut out by door open

Srt

open

0: Disable

Power On Delay

Pod

Delay time from power on until the outputs are activated

If Air temperature at power up is higher than this, power on delay

Power-on temperature

Pot

is overruled

Condenser

Con Blocked condenser protection.

Protection

Alarm limit for condenser temperature

Condenser Alarm Limit

CAL

Available only if condensor sensor is attached / assigned

Stop limit. If this temperature is exceeded, compressor must be

Condenser Block Limit

CbL

stopped

Available only if condensor sensor is attached/assigned

OK limit. Compressor is allowed to start again if the condenser

Condenser OK limit

CoL

temperature is lower than this temperature

Available only if condensor sensor is attached / assigned

Low limit. Compressor is not allowed to start if the condenser

Condenser Low Temp. Limit

CLL

temperature is lower than this temperature

Available only if condensor sensor is attached / assigned

Display

diS

Display settings

no: Display intensity use fixed value

Display intensity auto control

diC

yES: Display intensity controlled automaticlly by ambient light

Normal Intensity of display when no ambient light sensor is

Display Intensity

din

attached

Minimum intensity when ambient light sensor is attached

Unit Current

Menu

Def

Min

Max

Menu

Parameter name

code Description

setting

Display Unit

CFu

2.0

-100.0 200.0

°C

0.5

0.0

1.0

Temp sensor to display

trS

2.0

0.0

20.0

K

50.0 -100.0 200.0

°C

-35.0 -100.0 200.0

°C

Display Resolution

rES

no

no

yES

Display Range Limit

rLt

Display Delay

ddL

FAo

FAo

Aut

Display Offset

doF

0

0

240

Sec

0

0

240

Sec

Lock-time After defrost

dLt

0

0

960

Sec

0

0

960

Sec

10

0

960

Sec

Show Economy/Night Mode

SEC

0.0

-10.0

10.0

K

Show Pull Down

SSC

0

0

999

Sec

Show Holiday

SHo

Show Defrost

SdF

on

on

dor

Show compressor symbol

SCS

0

0

300

Sec

Show Fan symbol

SFS

50.0

-40.0

50.0

°C

Show Defrost symbol

SdS

30

0

360

min

Show ECO symbol

SES

Alarm

ALA Main menu for alarm settings

15

0

48

hour

High Temp Alarm

HAt

24

0

48

hour

Low Temp Alarm

LAt

High Alarm delay

Htd

0.0

-55.0

55.0

°C

Low Alarm delay

Ltd

Pulldown delay

Pdd

0.1

0.0

10.0

K

Door Open delay

dod

Voltage alarm

uAL

no

no

Hgd

Leakage alarm

LEA

no

no

yES

6.0

0.0

25.0

°C

Alarm Buzzer Duration

Abd

5.0

0.0

200.0

°C

6

1

96

hour

7

1

96

hour

Auto Clearance of Alarm

ACA

5

0

240

min

30

0

480

min

0

0

60

min

Auto-

0

0

600

sec

Heater

AHC

Control

25.0

-25.0

25.0

°C

Automatic heater mode

AuH yES: Heater will be active if air-temperature is too low

enable

no

no

yES

Energy mode delay

End

Auto Heat set point

AHS

no

no

yES

Auto heat differential

AHd Thermostat differential for auto heatting

0

0

24

hour

ECO

ECS

strategy

-50.0

-50.0

0.0

°C

ECO on / off

ECo

5.0

0.0

30.0

K

Door Actions

EdA

3

0

96

hour

Pir Actions

EPA

100

0

999

cycle

Action counter time

ECt

Door delay

Edd

no

no

yES

Pir delay

EPd

0

0

270

Vac

Shop Light Day

SLd

0

0

270

Vac

270

0

270

Vac

Shop Light Night

SLn

no

no

Aut

Time to pull down

tto

0

0

60

min

Light Source delay on ECO

LSd

1

0

60

min

EWU active

2

0

30

min

Euu

on / off

0

0

30

min

0

0

480

min

Shop close hour

CLH

0

0

15

min

Early wake up time offset

ErL

0

0

60

min

300

0

300

Sec

Holiday Length

HoL

-100

-100

200

°C

ECO manag.

ECA Main menu for ECO management

ECO Temperature Offset

Eto

80

0

200

°C

Holiday Temperature Offset

Hto

ECO Differential

diE

85

0

200

°C

ECO Fan on cycle

FoE

ECO Fan stop cycle

FSE

60

0

200

°C

ECO Cabinet light control

ELC

Eco Light delay

ELd

-5

-100

20

°C

Assign.

ASi

MODBUS Safety

uSA

no

no

yES

Temp Adj. for S1

t1A

Temp Adj. for S2

t2A

10

2

10

Unit Current

Def

Min

Max

C: Celsius

-C

-C

-F

F: Fahrenheit

SCo: Temperature control

EuA: Evaporator temperture

SCo

SCo

AuS

Con: Condenser temperature (Condenser cleaning)

AuS: Only for showing on display

0.1: Decimal with 0.1 degree resolution

0.5: Decimal with 0.5 degree resolution

0.1

0.1

1

1: Integers

no: Disabled. display is allowed to go outside of

‘ThSP — diF*SPr ~ ThSP + diF* (1 — SPr)’

no

no

yES

yES: Enabled. display is not allowed to go outside of

‘ThSP — diF*SPr ~ ThSP + diF*(1 — SPr)’

Time-constant for averaging of temperature at display

0

0

10

min

Temp value reaches 100 % when 5 * ddL expires

Correction for bad sensor placement. Value at 0 °C

0.0

-10.0

10.0

K

In order not to show a rising temperature during defrosting, the

displayed temperature is locked at the temperature shown at the

start of the defrost cycle for the number of minutes set in this

15

0

60

min

parameter

0: No lock

no: «ECo» and «ngt» will not be showed for Economy / Night Mode

yES: «ECo» or «ngt» will be displayed through whole

no

no

yES

Economy / Night Mode

no: «SC» will not be showed for Pull down state

no

no

yES

yES: «SC» will be displayed through whole Pull down state

no: Display will show temperature or ECO mode during holiday mode

no

no

yES

yES: Display will show «HoL» during holiday mode

no: Display will show temperature during defrost

yES

no

yES

yES: Display will show dEF during defrost

no: Compressor symbol will not show on display

yES

no

yES

yES: Show compressor symbol on display

no: Fan symbol will not show on display

yES

no

yES

yES: Show fan symbol on display

no: Defrost symbol will not show on display

yES

no

yES

yES: Show defrost symbol on display

no: ECO symbol will not show on display

yES

no

yES

yES: Show ECO symbol on display

High alarm limit

15.0 -100.0 200.0

°C

Low alarm limit

-50.0 -100.0 200.0

°C

Alarm delay time for high-temperature alarm

30

0

240

min

Alarm delay time for low-temperature alarm

0

0

240

min

Alarm delay time during & after defrost and after power up

240

0

960

min

(Only for high-temp. alarm)

Alarm delay on open door Alarm

2

0

60

min

0: Disable

no: No voltage alarm

no

no

yES

yES: Voltage alarm activated

Leakage detection for compressor protection

0

0

96

hour

0: Disable

0: Buzzer is off

[0. 999]: Buzzer will continue for the time set by the parameter

in minutes in which process the sound format is such as

0

0

999

min

IIIIIIII______________________IIIIIIIIII_____

999: Buzzer continues for ever with

IIIIIIIII______________________IIIIIIIIII__________ and so on

no: Disable this function; alarm status will not disappear

automatically without acknowledge by user even if the alarm

recovers

yES

no

yES

yES: Enable this function; alarm status can change from active to

inactive automatically on condition that the alarm recovers

(Errors are always auto-clearance enabled)

Main menu for Street cooler settings

(Street-Cooler : Coolers placed in the street with frost

protection )

no

no

yES

no: Normal operation

Delay between heater and compressor operation

60

0

360

min

Heater Set point: the set point of auto heating

2.0

-100.0 200.0

°C

2.0

0.0

20.0

K

Main menu for ECO strategy

Eco active or not

yES

no

yES

If no all other settings are not active

Times of door action to trigger exiting ECO

1

1

10

(Only can be accessed by Danfoss)

Times of PIR action to trigger exiting ECO

1

1

10

(Only can be accessed by Danfoss)

Door action or PIR action within action counter time can trigger

30

0

180

min

exiting ECO (Only can be accessed by Danfoss)

Door delay after door close to trigger entering ECO

180

0

180

min

(Only can be accessed by Danfoss)

PIR delay to trigger entering ECO

120

0

180

min

(Only can be accessed by Danfoss)

Shop light level during opening hours

When above this level ECO mode is canceled

5

0

80

Disabled if no light sensor connected/assigned

Shop light level during closing hours

When below this level ECO mode is enabled

3

0

80

Disabled if no light sensor connected/assigned

Time which ERC stay in ECO and holiday mode to decide to enter

0

0

168

hour

Pull down or Serving mode

Time delay for light source to change from serving mode source

0

0

180

min

to ECO mode source

Enable or disable early wake up

yES

no

yES

Shop is assumed to be closed when staying in ECO mode longer

6

0

24

hour

than shop close hour

Time of exiting ECO mode for next

day: Time of first activity to exit ECO mode — the Early wake-up time

120

0

240

min

0: Early wake up function disabled

In case that no activity has been registered for a number of days

specified by the Holiday, the Early-wake-up is deactivated and the

72

0

999

hour

cooler must stay in Holiday mode until activity is detected

If this offset is below zero, it means that Night mode will be

4.0

-25.0

25.0

K

activated instead of ECO mode

Increase or decrease of temperature with respect to normal mode

6.0

-25.0

25.0

K

during Holiday mode

Thermostat differential for ECO

2.0

0.0

10.0

K

On time for fan during compressor off period in ECO mode

0

0

960

Sec

Off time for fan during compressor off period in ECO mode

0

0

960

Sec

on: Always ON (Button is default to control light for all these options)

oFF: Always OFF

on

on

dor

dor: Door sensor only

Delay from shop light is turned on or off till mode shift is allowed

5

0

10

min

Assignment of inputs and outputs

no: MODBUS auto detection is enabled

no

no

yES

yES: MODBUS communication is deactivaed

Adjust value for sensor1 before being used by application

0.0

-20.0

20.0

K

Adjust value for sensor2 before being used by application

0.0

-20.0

20.0

K

Menu

Menu

Parameter name

code Description

setting

Temp Adj. for S3

t3A

Adjust value for sensor3 before being used by application

Temp Adj. for S4

t4A

Adjust value for sensor4 before being used by application

Sensor type used for sensor input 1/2/3

S1C

Stn: Standard NTC 5k @ 25 °C (EKS211) in Celsius

S1/S2/S3 Config

S2C

Htn: High temperature NTC 100k @ 25 °C in Celsius

S3C

Ldr: Light sensor(LDR). Luminens

dig: Digital input. On / Off

Stn: Standard NTC 5k @ 25 °C (EKS211). in Celsius

Htn: High temperature NTC 100k @ 25 °C. in Celsius

S4 Config

S4C

Pt1: PT1000 sensor 1000K @ 0 °C. in Celsius

Ldr: Light sensor(LDR). Luminens

dig: Digital input. On / Off

Select the function to be controlled via the Sensor 1 / 2 / 3

nC: Not connected

SCo: Temperature control

EuA: Evaporator temperture

S1A

Con: Condenser temperature (Condenser cleaning)

S1/S2/S3 Application

S2A

AuS: Only for showing temperature on display

S3A

Ldr: Light sensor(LDR). Luminens

ECo: External input to control ECO mode

doC: Door contact. Contact closed when door closed

doo: Door contact. Contact open when door closed

Select the function to be controlled via the Sensor 4 input

nC: Not connected

SCo: Temperature control

EuA: Evaporator temperture

Con: Condenser temperature (Condenser cleaning)

S4 Application

S4A

AuS: Only for showing temperature on display

Ldr: Light sensor (LDR). Luminens

ECo: External input to control ECO mode

doC: Door contact. Contact closed when door closed

doo: Door contact. Contact open when door closed

bt5: Button5

Select the function to be controlled via the digital I/O

non: Not used. (If communication is available depending on

MODBUS safety)

DI Config

diC

doC: Door contact. Contact closed when door closed

doo: Door contact. Contact open when door closed

ECo: External input to control ECO mode

Pir: Movement sensor (Passive infrared)

CoP: Compressor (With ZeroCrossing)

PiC: Pilot compressor (No ZeroCrossing)

DO1 Config

o1C

HEt: Inverse output. Heating application (With ZeroCrossing)

PiH: Pilot Heat relay (No ZeroCrossing)

no: Not used

dEF: Electric defrost heater / Valve for hot gas

DO2 Config

o2C

ALA: Alarm output

FAn: Fan control

Lig: Light control

DO3 Config

o3C

Same as DO2 Config

DO4 Config

o4C

Same as DO2 Config

Config of key 1 short. Lower left

noP: Not operating

tP: Increase Setpoint

tn: Decrease setpoint

b1C

ECo: Toggle Eco mode

Button 1 Short Config

b2C

Lig: Toggle light

b3C

dEF: Toggle defrost

SuP: Toggle Super-Cool /Pull-down

diP: Increase display intensity

din: Decrease display intensity

CFA: Toggle Celsius and Fahrenheit

Config of key 1 long. lower left

noP: Not operating

tP: Increase Setpoint

tn: Decrease setpoint

ECo: Toggle Eco mode

Lig: Toggle light

b1L

dEF: Toggle defrost

Button 1 Long Config

b2L

SuP: Toggle Super-Cool /Pull-down

b3L

diP: Increase display intensity

din: Decrease display intensity

CFA: Toggle Celsius and Fahrenheit

PoF: ERC power ON/OFF

HoL: Enter holiday mode

inF: Enter Info menu

Button 4 Short Config

b4C

Config of key 4 short. Lower right. As key 1 short

Config of key 4 long. Lower right

noP: Not operating

tP: Increase Setpoint

tn: Decrease setpoint

tn: Decrease setpoint

ECo: Toggle Eco mode

Lig: Toggle light

Button 4 Long Config

b4L

dEF: Toggle defrost

SuP: Toggle Super-Cool /Pull-down

diP: Increase display intensity

din: Decrease display intensity

CFA: Toggle Celsius and Fahrenheit

PoF: ERC power ON/OFF

HoL: Enter holiday mode

Config of key 5 short. Lower right

noP: Not operating

ECo: Toggle Eco mode

Button 5 Short Config

b5C

SuP: Toggle Super-Cool / Pull-down

Lig: Toggle light

dEF:Toggle defrost

Config of key 5 long. Lower right

noP: Not operating

ECo: Toggle Eco mode

SuP: Toggle Super-Cool / Pull-down

Button 5 Long Config

b5L

Lig: Toggle light

dEF: Toggle defrost

PoF: ERC power ON / OFF

HoL: Enter holiday mode

Shop owner

Most common parameters for instance real time clock. day / night

Pass-word level1

PS1

mode etc.

0: Disabled

Service technician

all parameters with read permission and possibility to change a

Pass-word level2

PS2

number of parameters like defrost, fan etc.

0: Disabled

OEM Customer

All parameters read and write permission. But with some

Pass-word level3

PS3

restriction to for instance reset statictical information

0: Disabled

Danfoss can accept no responsibility for possible errors in catalogues, brochures and other printed material. Danfoss reserves the right to alter its products without notice. This also applies to products

already on order provided that such alterations can be made without subsequent changes being necessary in specifications already agreed. All trademarks in this material are property of the property

of the respective companies. Danfoss and Danfoss logotype are trademarks of Danfoss A/S. All rights reserved.

Unit Current

Def

Min

Max

setting

0.0

-20.0

20.0

K

0.0

-20.0

20.0

K

Stn

Stn

dig

Stn

Stn

dig

SCo

nC

doo

nC

nC

bt5

non

non

Pir

CoP

CoP

PiH

dEF

0

Lig

FAn

0

Lig

Lig

0

Lig

noP

noP

CFA

PoF

noP

InF

tn

noP

CFA

Lig

noP

HoL

noP

noP

dEF

noP

noP

HoL

0

0

999

0

0

999

0

0

999