-
Catalog
-
Sign In
-
Contacts
-
Forum
-
Eng
- Error Codes
- Kyocera
- FSC8520MFP
- Code 4600
- Code: 4600
- Description: LSU cleaning motor error
When the LSU cleaning motor is driven, an error signal is detected continuously for 1 s. - Causes: Defective connector cable or poor contact in the connector. Defective drive transmission system. Defective motor. Defective PWB.
- Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity of the connector cable. If none, replace the cable. LSU cleaning motor and LSU connect PWB(YC11) LSU connect PWB and engine PWB(YC12)
Defective drive transmission system. Check if the rollers and gears rotate smoothly. If not, grease the bushings and gears. Check for broken gears and replace if any.
Defective motor. Replace the LSU cleaning motor.
Defective PWB. Replace the engine PWB or LSU connect PWB check for correct operation.
Все современные копировальные аппараты, мфу и принтеры Kyocera имеют возможность диагностировать все узлы устройства в режиме запуска и во время работы аппарата. По этому, если во время включения или во время работы произошел сбой, то техника Kyocera сможет сообщить о наличии ошибки.
В большинстве случаев у аппаратов Kyocera код ошибки отображается на дисплее, в остальных случаях тип ошибки зависит от последовательности и количества миганий индикаторов.
Если Ваш копировальный аппарат, МФУ или принтер Kyocera выдал на дисплее некий код, то узнать причину, описание возникновения ошибки, а так же в каком узле аппарата стоит искать проблему, Вы можете в этом разделе выбрав интересующую модель из списка.
Но диагностика не решит проблему сбоя аппарата, для этого лучше обратиться к профессиональным и опытным сервисным специалистам компании Kyomart! Позвоните нам по телефону
8 (343) 288-23-45 или отправьте запрос на электронную почту: sales@kyomart.ru , и мы обязательно свяжемся с Вами в кратчайшие сроки.
Код ошибки Описание ошибки Причина ошибки 0030 FAX control PWB system error
Processing with the fax software was disabled due to a hardware problem. Defective FAX control PWB. 0060 Engine PWB type error Defective engine sub PCB. 0070 FAX control PWB incompatible detection error
Abnormal detection of FAX control PWB incompatibility In the initial communication with the FAX control PWB, any normal communication command is not transmitted. Defective FAX software
Defective FAX control PWB. 0100 Backup memory device error Defective flash memory. 0120 MAC address data error
For data in which the MAC address is invalid. Defective main PWB.
Defective flash memory.
Defective engine PWB. 0130 Backup memory read/write error (main PWB) Defective flash memory.
Defective main PWB. 0140 Backup memory data error (main PWB) Defective flash memory.
Defective main PWB. 0150 Backup memory read/write error (engine PWB)
Detecting engine PWB EEPROM communication error. Improper installation engine PWB EEPROM.
Defective engine PWB.
Device damage of EEPROM. 0160 Backup memory data error (engine PWB) Defective flash memory.
Defective engine PWB. 0170 Billing counting error
A checksum error is detected in the main and engine backup memories for the billing counters. Data damage of EEPROM.
Defective PWB. 0180 Machine number mismatch
Machine number of main and engine does not match. Data damage of EEPROM. 0320 I/O CPU communication error
A communication error is detected 10 times in succession. Defective PWB. 0630 DMA error DMA transmission of image data does not complete within the specified period of time. Poor contact in the connector terminals. Defective main PWB. 0800 Image processing error
JAM05 is detected twice. Defective main PWB. 0830 FAX control PWB flash program area checksum error
A checksum error occurred with the program of the FAX control PWB. Defective FAX software.
Defective FAX control PWB. 0840 Faults of RTC
The time is judged to go back based on the comparison of the RTC time and the current time or five years or more have passed. The battery is disconnected from the main PWB.
Defective main PWB. 0870 FAX control PWB to main PWB high capacity data transfer error
High-capacity data transfer between the FAX control PWB and the main PWB of the machine was not normally performed even if the data transfer was retried the specified times. Improper installation FAX control PWB.
Defective FAX control PWB or main PWB. 0920 Fax file system error
The backup data is not retained for file system abnormality of flash memory of the FAX control PWB. Defective FAX control PWB. 1010 Lift motor error
After cassette 1 is inserted, lift sensor does not turn on within 12 s. This error is detected four times successively. Defective bottom plate elevation mechanism in the cassette.
Defective connector cable or poor contact in the connector.
Defective drive transmission system of the lift motor.
Defective lift motor.
Defective engine PWB. 1020 PF lift motor error (paper feeder)
After cassette 2 is inserted, PF lift sensor 1 does not turn on within 12 s. This error is detected four times successively. Defective bottom plate elevation mechanism in the cassette.
Defective connector cable or poor contact in the connector.
Defective drive transmission system of the PF lift motor 1.
Defective PF lift motor 1.
Defective PF main PWB. 1030 PF lift motor error (paper feeder)
After cassette 3 is inserted, PF lift sensor 2 does not turn on within 12 s. This error is detected four times successively. Defective bottom plate elevation mechanism in the cassette.
Defective connector cable or poor contact in the connector.
Defective drive transmission system of the PF lift motor 2.
Defective PF lift motor 2.
Defective PF main PWB. 1800 Paper feeder communication error
A communication error is detected 10 times in succession. Improper installation paper feeder.
Defective connector cable or poor contact in the connector.
Defective engine PWB.
Defective PF main PWB. 1900 Paper feeder EEPROM error
When writing the data, the write data and the read data is not continuously in agreement 5 times. Defective PF main PWB.
Device damage of EEPROM. 2000 Main motor steady-state error
Stable OFF is detected for 1 s continuously after main motor stabilized. Defective connector cable or poor contact in the connector.
Defective drive transmission system of the main motor.
Defective main motor.
Defective engine PWB. 2010 Main motor drive error
The main motor is not stabilized within 2 s after driving starts. Defective connector cable or poor contact in the connector.
Defective drive transmission system of the main motor.
Defective main motor.
Defective engine PWB. 2101 Developer motor K steady-state error
The rated speed signal detected the stability OFF continuously for 1 s after the developer motor K stabilizes. Defective connector cable or poor contact in the connector.
Defective drive transmission system.
Defective motor.
Defective PWB. 2102 Developer motor YCM steady-state error
The rated speed signal detected the stability OFF continuously for 1 s after the developer motor YCM stabilizes. Defective connector cable or poor contact in the connector.
Defective drive transmission system.
Defective motor.
Defective PWB. 2111 Developer motor K startup error
Developer motor K is not stabilized within 2 s since the motor is activated. Defective connector cable or poor contact in the connector
Defective drive transmission system.
Defective motor.
Defective PWB. 2112 Developer motor YCM startup error
Developer motor YCM is not stabilized within 2 s since the motor is activated. Defective connector cable or poor contact in the connector
Defective drive transmission system.
Defective motor.
Defective PWB. 2300 Fuser motor steady-state error
The rated speed signal detected the stability OFF continuously for 1 s after the fuser motor stabilizes. Defective connector cable or poor contact in the connector.
Defective drive transmission system.
Defective motor.
Defective PWB. 2310 Fuser motor startup error
Fuser motor is not stabilized within 2 s since the motor is activated. Defective connector cable or poor contact in the connector.
Defective drive transmission system.
Defective motor.
Defective PWB. 2550 Conveying motor steady-state error
The rated speed signal detected the stability OFF continuously for 1 s after the conveying motor stabilizes. Defective connector cable or poor contact in the connector.
Defective drive transmission system.
Defective motor.
Defective PWB. 2560 Conveying motor startup error
Conveying motor is not stabilized within 2 s since the motor is activated. Defective connector cable or poor contact in the connector.
Defective drive transmission system.
Defective motor.
Defective PWB. 2600 PF drive motor error (paper feeder)
When the PF drive motor is driven, error signal is detected continuously for 1 s. Defective connector cable or poor contact in the connector.
Defective drive transmission system of the PF drive motor.
Defective PF drive motor.
Defective PF main PWB. 2700 TC belt motor error
When the TC belt motor is driven, error signal is detected continuously for 1 s. Defective connector cable or poor contact in the connector.
Defective drive transmission system of the PF drive motor.
Defective PF drive motor.
Defective PF main PWB. 3100 ISU home position error
The home position is not correct when the power is turned on or at the start of copying using the table. Defective connector cable or poor contact in the connector.
Defective home position sensor.
Defective ISU motor.
Defective CCD PWB.
Defective engine PWB. 3200 Exposure lamp error
When input value at the time of exposure lamp illumination does not exceed the threshold value between 5 s. Defective connector cable or poor contact in the connector.
Defective exposure lamp.
Defective CCD PWB.
Defective main PWB. 3500 Communication error between scanner and ASIC
An error code is detected 3 times in succession. Defective connector cable or poor contact in the connector.
Defective CCD PWB.
Defective main PWB. 3600 Scanner sequence error Defective main PWB or engine PWB. 4000 Polygon motor synchronization error
The polygon motor is not stabilized within 10 s after driving starts. Defective connector cable or poor contact in the connector.
Defective polygon motor.
Defective engine PWB. 4001 Polygon motor (K) steady-state error
The rated speed signal detected the stability OFF continuously for 1 s after the polygon motor (K) stabilizes. Defective connector cable or poor contact in the connector.
Defective motor
Defective PWB. 4002 Polygon motor (С) steady-state error
The rated speed signal detected the stability OFF continuously for 1 s after the polygon motor (С) stabilizes. Defective connector cable or poor contact in the connector.
Defective motor
Defective PWB. 4003 Polygon motor (M) steady-state error
The rated speed signal detected the stability OFF continuously for 1 s after the polygon motor (M) stabilizes. Defective connector cable or poor contact in the connector.
Defective motor
Defective PWB. 4004 Polygon motor (Y) steady-state error
The rated speed signal detected the stability OFF continuously for 1 s after the polygon motor (Y) stabilizes. Defective connector cable or poor contact in the connector.
Defective motor
Defective PWB. 4010 Polygon motor steady-state error
Stable OFF is detected for 1 s continuously after polygon motor stabilized. Defective connector cable or poor contact in the connector.
Defective polygon motor.
Defective engine PWB. 4011 Polygon motor (K) startup error
Polygon motor (K) is not stabilized within 10 s since the motor is activated. Defective connector cable or poor contact in the connector.
Defective motor.
Defective PWB. 4012 Polygon motor (C) startup error
Polygon motor (C) is not stabilized within 10 s since the motor is activated. Defective connector cable or poor contact in the connector.
Defective motor.
Defective PWB. 4013 Polygon motor (M) startup error
Polygon motor (M) is not stabilized within 10 s since the motor is activated. Defective connector cable or poor contact in the connector.
Defective motor.
Defective PWB. 4014 Polygon motor (Y) startup error
Polygon motor (Y) is not stabilized within 10 s since the motor is activated. Defective connector cable or poor contact in the connector.
Defective motor.
Defective PWB. 4100 BD initialization error
BD is not detected within 1 s after polygon motor stabilized. Defective connector cable or poor contact in the connector.
Defective APC PWB.
Defective BD PWB.
Defective main PWB. 4600 LSU cleaning motor error
When the LSU cleaning motor is driven, an error signal is detected continuously for 1 s. Defective connector cable or poor contact in the connector.
Defective drive transmission system.
Defective motor. Defective PWB. 4700 VIDEO ASIC device error Defective connector cable or poor contact in the connector.
Defective main PWB or engine PWB. 4950 LSU CPU communication error
A communication error is detected 10 times in succession. Defective connector cable or poor contact in the connector.
Defective PWB. 6000 Broken fuser heater wire
The detected temperature of fuser thermistor does not reach the specified temperature (ready indication temperature) after the fuser heater has been turned on continuously for 60 s in warming up. The fusing temperature at 7 seconds and 20 seconds since fuser temperature control has occurred differs by 43°C/109.4°F or less. Defective connector cable or poor contact in the connector.
Deformed connector pin.
Defective triac.
Fuser thermostat triggered.
Broken fuser heater wire.
Defective engine PWB. 6000
6020
6030
6050 Broken fuser heater wire
Abnormally high fuser thermistor temperature Broken fuser thermistor wire Abnormally low fuser thermistor temperature Deformed connector pin.
Defective triac. 6020 Abnormally high fuser thermistor temperature
The fuser thermistor detects a temperature higher than 230°C/446°F continuously for 40 ms. High fuser temperature signal detects a temperature of 255°C/491°F continuously for 40 ms. Deformed connector pin.
Defective triac.
Shorted fuser thermistor.
Defective engine PWB. 6030 Broken fuser thermistor wire
A/D value of the fuser thermistor exceeds 251 bit continuously for 7 s during warming up. Defective connector cable or poor contact in the connector.
Deformed connector pin.
Defective triac.
Defective fuser thermistor.
Defective engine PWB 6050 Abnormally low fuser thermistor temperature
As the stable temperature has reached the second time, the decrease in the fuser thermistor temperature of 60°C/140°F or greater is detected for one second. Deformed connector pin.
Defective triac.
Defective fuser thermistor
Defective fuser heater.
Defective engine PWB. 6120 Abnormally high fuser thermistor 3 (press roller) temperature
The fuser temperature exceeds 200 °C/392 °F for 1 s. Deformed connector pin.
Defective IH PWB.
Defective fuser thermistor.
Defective engine PWB. 6130 Fuser thermistor 3 (press roller) break error Fuser thermistor 3 detects a temperature of -14 °C/6.8 °F . Fuser thermistor 3 does not reach 30° C/86 °F even after20 s during warming up. Defective connector cable or poor contact in the connector
Deformed connector pin.
Defective IH PWB.
Defective fuser thermistor.
Defective engine PWB. 6150 Abnormally low fuser thermistor 3 (press roller) temperature
The fuser temperature lower than 30 °C/86 °F is detected continuously for 1 s. Deformed connector pin.
Defective fuser thermistor
Defective fuser heater.
Defective engine PWB. 6200 Broken fuser edge heater wire
Fuser thermistor 1 does not reach 50° C/122 °F even after20 s during warming up. The detected temperature of fuser thermistor1 does not reach the specified temperature (ready indication temperature) for 20 s in warming up after reaching 50° C/122 °F. Defective connector cable or poor contact in the connector.
Deformed connector pin.
Fuser thermostat triggered.
Broken fuser heater wire.
Defective engine PWB. 6220 Abnormally high fuser thermistor 1 (edge) temperature
The fuser temperature exceeds 240 °C/464 °F for 1 s Defective connector cable or poor contact in the connector.
Deformed connector pin.
Fuser thermostat triggered.
Broken fuser heater wire.
Defective engine PWB. 6230 Fuser thermistor 1 (edge) break error
During warming up a hearter, fuser thermistor 2 detects a temperature of 100 °C/212 °F or higher and, fuser thermistor 1 detects a temperature of 37 °C/99 °F or lower. Defective connector cable or poor contact in the connector.
Deformed connector pin.
Fuser thermostat triggered.
Broken fuser heater wire.
Defective engine PWB. 6250 Abnormally low fuser thermistor 1 (edge) temperature
The fuser temperature lower than 100 °C/212 °F is detected continuously for 1 s during printing. The fuser temperature lower than 50 °C/122 °F is detected continuously for 1 s during pre-heating. Defective connector cable or poor contact in the connector.
Deformed connector pin.
Fuser thermostat triggered.
Broken fuser heater wire.
Defective engine PWB. 6400 Zero-cross signal error
While fuser heater control is performed, the zero-cross signal is not input within 3 s. Defective connector cable or poor contact in the connector
Defective power source PWB or engine PWB. 6410 Fuser unit type mismatch problem
Absence of the fuser unit is detected. Fuser unit connector inserted incorrectly.
Different type of the fuser unit is installed. 6600 Belt rotation error
The belt was detected to stop for 1 s continuously during motor remote is on. Defective fuser motor.
Defective IH belt.
Defective IH PWB.
Defective engine PWB. 7101 Toner sensor K error Defective Developer unit.
Defective PWB. 7102 Toner sensor C error Defective Developer unit.
Defective PWB. 7103 Toner sensor M error Defective Developer unit.
Defective PWB. 7104 Toner sensor Y error Defective Developer unit.
Defective PWB. 7401 Developing unit K type mismatch problem
Absence of the developing unit K is detected. Developing unit connector inserted incorrectly.
Different type of the developing unit is installed.
Defective PWB. 7402 Developing unit C type mismatch problem
Absence of the developing unit C is detected. Developing unit connector inserted incorrectly.
Different type of the developing unit is installed.
Defective PWB. 7403 Developing unit M type mismatch problem
Absence of the developing unit M is detected. Developing unit connector inserted incorrectly.
Different type of the developing unit is installed.
Defective PWB. 7404 Developing unit Y type mismatch problem
Absence of the developing unit Y is detected. Developing unit connector inserted incorrectly.
Different type of the developing unit is installed.
Defective PWB. 7411 Drum unit K type mismatch problem
Absence of the drum unit K is detected. Drum unit connector inserted incorrectly.
Different type of the drum unit is installed.
Defective PWB. 7412 Drum unit C type mismatch problem
Absence of the drum unit C is detected. Drum unit connector inserted incorrectly.
Different type of the drum unit is installed.
Defective PWB. 7413 Drum unit M type mismatch problem
Absence of the drum unit M is detected. Drum unit connector inserted incorrectly.
Different type of the drum unit is installed.
Defective PWB. 7414 Drum unit Y type mismatch problem
Absence of the drum unit Y is detected. Drum unit connector inserted incorrectly.
Different type of the drum unit is installed.
Defective PWB. 7420 Transfer belt unit type mismatch problem
Absence of the transfer belt unit is detected. Transfer belt unit connector inserted incorrectly.
Different type of the transfer belt unit is installed.
Defective PWB. 7601 ID sensor 1 (front) error Defective ID sensor.
Defective PWB. 7602 ID sensor 2 (rear) error Defective ID sensor.
Defective PWB. 7611 ID sensor (K) density error
When ID sensor 2 detected CTD is 500 or less. Defective ID sensor.
Defective PWB. 7612 ID sensor (C) density error
When ID sensor 2 detected CTD is 500 or less. Defective ID sensor.
Defective PWB. 7613 ID sensor (M) density error
When ID sensor 2 detected CTD is 500 or less. Defective ID sensor.
Defective PWB. 7614 ID sensor (Y) density error
When ID sensor 2 detected CTD is 500 or less. Defective ID sensor.
Defective PWB. 7620 ID sensor timing error
Color registration correction was failed. Defective ID sensor.
Defective PWB. 7800 Broken external thermistor wire
The thermistor output value is 0.3 V or less. Defective connector cable or poor contact in the connector.
Defective temperature sensor. 7810 Short-circuited external thermistor wire
The thermistor output value is 3 V or more. Defective connector cable or poor contact in the connector.
Defective temperature sensor. 7900 Drum unit EEPROM error
No response is issued from the device in reading/writing for 5 ms or more and this problem is repeated five times successively. Mismatch of reading data from two locations occurs eight times successively. Mismatch between writing data and reading data occurs eight times successively. Defective connector cable or poor contact in the connector.
Defective drum unit. 7901 Drum K EEPROM error
No response is issued from the device in reading/writing for 5 ms or more and this problem is repeated five times successively. Mismatch of reading data from two locations occurs eight times successively. Mismatch between writing data and reading data occurs eight times successively. Defective connector cable or poor contact in the connector.
Defective drum unit. 7902 Drum C EEPROM error
No response is issued from the device in reading/writing for 5 ms or more and this problem is repeated five times successively. Mismatch of reading data from two locations occurs eight times successively. Mismatch between writing data and reading data occurs eight times successively. Defective connector cable or poor contact in the connector.
Defective drum unit. 7903 Drum M EEPROM error
No response is issued from the device in reading/writing for 5 ms or more and this problem is repeated five times successively. Mismatch of reading data from two locations occurs eight times successively. Mismatch between writing data and reading data occurs eight times successively. Defective connector cable or poor contact in the connector.
Defective drum unit. 7904 Drum Y EEPROM error
No response is issued from the device in reading/writing for 5 ms or more and this problem is repeated five times successively. Mismatch of reading data from two locations occurs eight times successively. Mismatch between writing data and reading data occurs eight times successively. Defective connector cable or poor contact in the connector.
Defective drum unit. 7910 Developer unit EEPROM error
No response is issued from the device in reading/writing for 5 ms or more and this problem is repeated five times successively. Mismatch of reading data from two locations occurs eight times successively. Mismatch between writing data and reading data occurs eight times successively. Defective connector cable or poor contact in the connector.
Defective developer unit. 7911 Developing unit K EEPROM error
No response is issued from the device in reading/writing for 5 ms or more and this problem is repeated five times successively. Mismatch of reading data from two locations occurs eight times successively. Mismatch between writing data and reading data occurs eight times successively. Poor contact in the connector terminals.
Defective developing PWB. 7912 Developing unit C EEPROM error
No response is issued from the device in reading/writing for 5 ms or more and this problem is repeated five times successively. Mismatch of reading data from two locations occurs eight times successively. Mismatch between writing data and reading data occurs eight times successively. Poor contact in the connector terminals.
Defective developing PWB. 7913 Developing unit M EEPROM error
No response is issued from the device in reading/writing for 5 ms or more and this problem is repeated five times successively. Mismatch of reading data from two locations occurs eight times successively. Mismatch between writing data and reading data occurs eight times successively. Poor contact in the connector terminals.
Defective developing PWB. 7914 Developing unit Y EEPROM error
No response is issued from the device in reading/writing for 5 ms or more and this problem is repeated five times successively. Mismatch of reading data from two locations occurs eight times successively. Mismatch between writing data and reading data occurs eight times successively. Poor contact in the connector terminals.
Defective developing PWB. 8030 Tray upper limit detection problem (document finisher)
When the tray elevation motor raises a tray, the ON status of the tray upper limit sensor is detected. Defective connector cable or poor contact in the connector.
Defective tray upper limit sensor, paper surface sensor 1/2.
Defective DF main PWB. 8040 Belt problem (document finisher)
The belt sensor does not turn on/off within specified time of the belt solenoid turning on. Defective connector cable or poor contact in the connector.
Defective belt sensor.
Defective belt solenoid.
Defective DF main PWB. 8140 Tray elevation motor problem (document finisher)
The tray low limit sensor or paper surface sensor 1/2 cannot be detected to be on within 10 s since the tray elevation motor is activated. Defective connector cable or poor contact in the connector.
Defective connector cable or poor contact in the connector.
The tray elevation motor malfunctions.
Defective tray lower limit sensor, paper surface sensor 1/2.
Defective DF main PWB. 8210 Stapler problem (document finisher)
Jam 7012 or 7023 is indicated. Defective connector cable of staple or poor contact in the connector.
The stapler is blocked with a staple.
The stapler is broken
Defective DF main PWB. 8320 Adjustment motor 2 problem (document finisher)
The adjustment sensor 2 does not turn on/off within specified time of the adjustment motor 2 turning on. Defective connector cable or poor contact in the connector.
Defective adjustment sensor 2.
Defective adjustment motor 2.
Defective DF main PWB. 8330 Adjustment motor 1 problem (document finisher)
The adjustment sensor 1 does not turn on/off within specified time of the adjustment motor 1 turning on. Defective connector cable or poor contact in the connector.
Defective adjustment sensor 1.
Defective adjustment motor 1. 8350 Roller motor problem (document finisher)
The roller sensor does not turn on/off within specified time of the roller motor turning on. Defective DF main PWB.
Defective connector cable or poor contact in the connector.
Defective roller sensor.
Defective roller motor.
Defective DF main PWB. 8360 Slide motor problem (document finisher)
The slide sensor does not turn on/off within specified time of the slide motor turning on. Defective connector cable or poor contact in the connector.
Defective slide sensor.
Defective slide motor.
Defective DF main PWB. 8460 EEPROM problem (document finisher)
Reading from or writing to EEPROM cannot be performed. Defective EEPROM or DF main PWB. 8800 Document finisher communication error
A communication error is detected 10 times in succession. Defective connector cable or poor contact in the connector
Defective DF main PWB.
Defective engine PWB. 8830 Bridge communication error (document finisher)
A communication error is detected 10 times in succession. Defective connector cable or poor contact in the connector.
Defective bridge PWB.
Defective engine PWB. 8990 Document finisher communication error Defective connector cable or poor contact in the connector.
Defective DF main PWB.
Defective bridge PWB. 9000 Document processor communication error
A communication error is detected 10 times in succession. Defective connector cable or poor contact in the connector.
Defective DP main PWB. 9060 DP EEPROM error Read and write data does not match. Data in the specified area of the backup memory does not match the specified values. Defective DP main PWB.
Device damage of EEPROM. 9500 BRU communication error IPU PWB error 9510 BRU PWB error IPU PWB error 9520 BRU PWB data error IPU PWB error F000 Main PWB — operation panel PWB communication error Defective main PWB.
Defective operation panel PWB. F010 Main PWB checksum error Defective main PWB. F040 Main PWB — print engine communication error Defective main PWB.
Defective engine PWB. F050 Print engine ROM checksum error Defective engine PWB.
-
06-11-2019
#1
Junior Member
- Rep Power
- 0
Kyocera M5521CDW Error code: C4600
Kyocera M5521CDW Error code: C4600
Hello,
I have a Kyocera Ecosys M5521CDW. Since 3 days it it has an Machine Failure, with Error code: C4600.
The advise that was given to me was; ‘buy a new one, because it is not worth to repair it’. Well, the printer is only 2 years and 4 months old, so i hope you guys can help me a little bit futher.What I do know: The error code C4600 stands for LSU Cleaning motor error.
Before I just buy a new one, is there anyone who can help me with this error code?
Thanks! Mike
-
06-11-2019
#2
Trusted Tech
50+ Posts
- Rep Power
- 10
Re: Kyocera M5521CDW Error code: C4600
Remove the connector from the main board for the cleaner motor.
Sent from my XT1635-01 using Tapatalk
-
06-11-2019
#3
Junior Member
- Rep Power
- 0
Re: Kyocera M5521CDW Error code: C4600
Originally Posted by djs9164
Remove the connector from the main board for the cleaner motor.
Sent from my XT1635-01 using Tapatalk
Thank you for your quick reply. Is it possible to give me an indication where it is located on the main board? See attaches picture.
IMG_4027.jpg
Thanks in advance!
-
06-11-2019
#4
Trusted Tech
50+ Posts
- Rep Power
- 10
Re: Kyocera M5521CDW Error code: C4600
Originally Posted by miketw
Thank you for your quick reply. Is it possible to give me an indication where it is located on the main board? See attaches picture.
IMG_4027.jpg
Thanks in advance!Need to look at a manual tonight. Should be a small 2 pin connector.
Sent from my XT1635-01 using Tapatalk
-
06-12-2019
#5
Trusted Tech
50+ Posts
- Rep Power
- 10
Re: Kyocera M5521CDW Error code: C4600
Originally Posted by djs9164
Need to look at a manual tonight. Should be a small 2 pin connector.
Sent from my XT1635-01 using Tapatalk
This made me more than in non-tech can handle. The boy that controls it is called the container relay board it’s located on the right hand side of the machine it’s a long narrow board. The connector you need to disconnect is y c 13 it is a two pin connector. Good luck
Sent from my XT1635-01 using Tapatalk
Originally Posted by djs9164
Code
4204
Laser output error (Yellow)
The pin photo signal (PDN) is not output
from PD PWB Y for one second while
laser is emitted.
4600
LSU cleaning motor error
When the LSU cleaning motor is driven,
the LSU cleaning motor over-current
detection signal is detected continu-
ously for 50 times (5 s) at 100 ms inter-
vals.
4700
VIDEO ASIC device error
Contents
Causes
Check procedures/corrective measures
Defective harness
Reinsert the connector. Also check for conti-
between APC
nuity within the connector harness. If none,
PWB Y and engine
remedy or replace the harness.
PWB (YC29), or
improper connec-
tor insertion.
Defective APC
Replace the laser scanner unit YK (See
PWB Y.
page 1-5-37).
Defective PD PWB
Replace the laser scanner unit YK (See
Y.
page 1-5-37).
Defective engine
Replace the engine PWB (See page 1-5-
PWB.
29).
Defective harness
Reinsert the connector. Also check for conti-
between LSU
nuity within the connector harness. If none,
cleaning motor and
remedy or replace the harness.
engine PWB
(YC37), or
improper connec-
tor insertion.
Defective drive
Check if the rollers and gears rotate
transmission sys-
smoothly. If not, grease the bushings and
tem of the LSU
gears. Check for broken gears and replace if
cleaning motor.
any.
Defective LSU
Replace the LSU cleaning motor.
cleaning motor.
Defective engine
Replace the engine PWB (See page 1-5-
PWB.
29).
Faulty connection
Check the installation of the main PWB and
of the connector
engine PWB and reinstall them if necessary
between the main
(See page 1-5-28 and 1-5-29).
PWB and engine
PWB.
Defective main
Replace the main PWB (See page 1-5-28).
PWB.
Defective engine
Replace the engine PWB (See page 1-5-
PWB.
29).
Remarks
2K8
1-4-11
Ошибка 4600
Ошибка блока лазера. Не работаетзаедает двигатель очистки лазера. Как правило из за пыли. Необходимо прочистить направляющие блока лазеров.
Разборка МФУ
- Отключаем МФУ от электросети
- Вынимаем лотки с бумагой
- Открываем крышку блока картриджей
- Выкручиваем винты из крышки слева
- Снимаем крышку
Блок лазеров
- Отсоединяем кабели
- Выкручиваем 4 винта крепления
- Вытаскиваем блок лазеров
Чистка блока лазеров
- Очищаем направляющие от пыли (продуть воздухом)
- Вставляем блок обратно
- Подключаем кабель, проверяем что бы все было плотно
- Подключаем электропитание, включаем МФУ и проверяем что все работает
- Собираем в обратном порядке
-
Catalog
-
Sign In
-
Contacts
-
Forum
-
Eng
- Error Codes
- Kyocera
- FSC8520MFP
- Code 4600
- Code: 4600
- Description: LSU cleaning motor error
When the LSU cleaning motor is driven, an error signal is detected continuously for 1 s. - Causes: Defective connector cable or poor contact in the connector. Defective drive transmission system. Defective motor. Defective PWB.
- Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity of the connector cable. If none, replace the cable. LSU cleaning motor and LSU connect PWB(YC11) LSU connect PWB and engine PWB(YC12)
Defective drive transmission system. Check if the rollers and gears rotate smoothly. If not, grease the bushings and gears. Check for broken gears and replace if any.
Defective motor. Replace the LSU cleaning motor.
Defective PWB. Replace the engine PWB or LSU connect PWB check for correct operation.
Thanks: 0
Dislikes: 0
-
01-15-2022
#1
Technician
- Rep Power
- 11
Kyocera 6635cidn error code 4600
Hi I work on some Kyocera copiers but have not worked on this one I see it has to do with cleaning mode just trying to see if I could get an idea what to do or look for thanks in advance
-
01-15-2022
#2
Re: Kyocera 6635cidn error code 4600
Yeah, it’s a failure of the laser slit glass cleaner to complete it’s cycle. It’s the same mechanism on Genesis, Mebius, & Mebius II. There are several reasons why this might occur:
I had a customer that would become irritated when the MFP tried to do it’s automatic laser slit glass cleaning during a print job, displaying: «Cleaning the Laser Unit.» The customer explained: «All I do is pull the power cord, and it stops that.» (**genius**). Now the cleaner is not at home position, & goes into C4600. Usually you get a void line in the images too, because the cleaners block the laser slit glasses. It’s simple enough to remove the consumables and loosen the laser unit screws. Lift each of the laser units (two) and rotate the cleaner drive to home the cleaner to the left. Make sure that it turns smoothly. Re-tighten the laser unit screws and re-install the consumables.
In dirty environments the cleaner can drag. Cleaning the worm drive and lubricating it with grease can help.
If the motor turns slowly or just will not run, the engine relay PWB may have a failing drive circuit. Temporarily home the cleaners to the left, then disconnect J26 on the engine relay PWB. The cleaner will not stall … it won’t move at all. But it also won’t clean the laser slit glasses, so you’ll be out more often to clean the laser slit glasses manually. (towel & glass cleaner). For the automated cleanings to resume, you’ll have to replace the engine relay PWB.
You can test the Laser Slit Glass Cleaner multiple times in the System Menu to see that it can complete several cycles.
=^..^=
If you’d like a serious answer to your request:
1) demonstrate that you’ve read the manual
2) demonstrate that you made some attempt to fix it.
3) if you’re going to ask about jams include the jam code.
4) if you’re going to ask about an error code include the error code.
5) You are the person onsite. Only you can make observations.
blackcat: Master Of The Obvious =^..^=
-
01-15-2022
#3
Re: Kyocera 6635cidn error code 4600
It�s a bit late once this error has started, but Kyocera have filters you can fit on the intake fans to prevent dust entering the laser scanner area.
It�s a bit of a job removing the lasers and the cleaning mechanism for replacement of a thorough clean. Good luck.
-
01-17-2022
#4
Re: Kyocera 6635cidn error code 4600
Usually theres problem with the pads not getting on slit glass.
Here is a video for mod that helped me with same problem — Laser Modification.mp4 — Google Drive
-
01-17-2022
#5
Re: Kyocera 6635cidn error code 4600
We’ve tried the modifications and were never successful. We just remove the augers and clean them whenever the customer gets streaks.
Tags for this Thread
Bookmarks
Bookmarks
Posting Permissions
- You may not post new threads
- You may not post replies
- You may not post attachments
- You may not edit your posts
- BB code is On
- Smilies are On
- [IMG] code is On
- [VIDEO] code is On
- HTML code is Off
Forum Rules
Японская компания Kyocera производит высококачественные лазерные принтеры и МФУ для офисной печати. Их продукция одна из самых востребованных на сегодняшний день. Ведь печатающие устройства Kyocera характеризуются высокой надежностью, износостойкостью и большим сроком эксплуатации. Однако даже их изделия не являются вечными. Со временем принтеры Kyocera начинают сбоить.
К счастью, оргтехника Kyocera оснащена системой самодиагностики (так же, как и струйные принтеры Canon). Поэтому, в случае возникновения проблемы, устройство самостоятельно выявит уязвимое место и сообщит Вам об этом миганием соответствующего индикатора на панели управления либо кодом ошибки, выведенным на дисплей принтера.
Если Вы не являетесь мастером по обслуживанию принтеров и МФУ Kyocera, то, чтобы понять, о чем сообщает печатающее устройство, Вам потребуется расшифровать указанный им код. Для этого мы добавили в статью таблицу кодов ошибок лазерных принтеров Kyocera серии FS и не только.
Коды ошибок принтеров и МФУ Kyocera, которые можно исправить самостоятельно
|
Код ошибки |
Значение ошибки |
Решение проблемы |
|
E-0001 (E1) |
Поврежден чип картриджа либо установлен неоригинальный картридж. |
Замените установленный картридж оригинальной версией изделия. Если хотите сэкономить, тогда купите и установите новый чип на картридж или перепрошейте принтер Kyocera. Однако предварительно не помешает попробовать сбросить ошибку соответствующей комбинацией клавиш (как это сделать, читайте в статье «Сброс ошибки установки неоригинального картриджа в принтерах Kyocera»). |
|
E-0002 (E2) |
Регион использования картриджа и принтера не совпадают. |
Замените чип или прошейте принтер Kyocera. |
|
E-0003 (E3) |
Заполнена память принтера или МФУ Kyocera. |
Отпечатайте ранее отсканированные листы или очистите очередь печати нажатием кнопки Стоп/Сброс (ранее отсканированные листы также удалятся из памяти принтера, даже если они еще не были распечатаны). |
|
E-0007 (E7) |
Тонер-картридж Kyocera израсходовал ресурс красящего вещества. |
Замените или заправьте картридж Kyocera (если используете совместимый или перезаправленный расходник, то после установки его в принтер не забудьте сбросить ошибку зажатием на 3-5 секунды кнопок [Ок] и [Сброс/Стоп]). |
|
E-0008 (E8) |
Открыта крышка принтера либо не работает датчик закрытия крышек устройства. |
Откройте и еще раз закройте переднюю и заднюю крышку принтера. Во время закрытия Вы должны услышать характерный щелчок. Если не помогло, то причина в неисправности датчика. |
|
E-0009 (E9) |
Лоток приема бумаги полон. |
Уберите все отпечатанные листы бумаги из выходящего лотка. Чтобы возобновить печать, нажмите кнопку [Старт]. |
|
E-0012 (E12) |
Ошибка памяти принтера Kyocera. |
Попробуйте уменьшить разрешение печати. Скорее всего, формат создаваемого отпечатка не соответствует возможностям принтера. |
|
E-0014 (E14) |
Установлен неверный формат бумаги (неподдерживаемый принтером Kyocera). |
Поменяйте бумагу на поддерживаемую принтером либо смените ее формат в настройках печати. Попробуйте обновить программное обеспечение. Возможно, это расширит поддерживаемые принтером Kyocera форматы. |
|
E-0015 (E15) |
Устройство не подключено к электрической сети либо на компьютере нет (не работает) драйвера принтера Kyocera. |
Проверьте подключение печатающего аппарата к электрической сети, а также целостность кабеля. Если ошибка не исчезает, скачайте драйвер принтера Kyocera и установите его на компьютер. |
|
E-0017 (E17) |
Ошибка передачи данных. |
Проверьте подключение принтера к компьютеру. Кабель не должен быть длиннее 5 метров, а также обязан поддерживать стандарт USB 2.0. Кроме того, переустановите драйвер принтера и утилиту Kyocera Client Tool. |
|
E-0018 (E18) |
Очередь печати заполнена. |
Очистите очередь печати нажатием кнопки [Сброс] либо через драйвер принтера. |
|
E-0019 (E19) |
Неверный формат печати. |
Отмените печать нажатием кнопки [Стоп/Сброс]. Выберите в настройках принтера соответствующий режим печати, а также установите в лоток поддерживаемый принтером формат бумаги. |
|
J-0000 (jam0000) |
Замятие бумаги за задней крышкой. |
Откройте крышку и извлеките бумагу. Проверьте надежность крепления бумаги в лотке, а также принтер на наличие посторонних предметов. Еще причина может быть в пружине выходного флажка. Если она растянулась, то может плохо работать фиксатор. Также проблема может быть из-за печки, сделайте ее ревизию, переборку и смазку. |
|
J-0501 (jam0501) |
Бумага застряла в принтере Kyocera |
Извлеките замятую бумагу. Проверьте надежность установки бумаги во входной лоток. Проверьте целостность роликов протяжки бумаги, а также принтер на наличие посторонних предметов. Если не помогло, стоит внимательно осмотреть ребра на направляющей пластине. На них могут образоваться сколы, трещины и заусенцы. Их можно слегка подчистить наждачной бумагой (нулевкой). |
|
J-0511 (jam0511) |
Принтер Kyocera замял бумагу. |
Извлеките замятую бумагу и повторите печать. Если проблема не исчезла, несите принтер в сервис. Скорее всего, изношен ролик протяжки бумаги. |
|
C7990 |
Бункер драм-картриджа (блока фотобарабана) заполнен отработанным тонером либо неисправен счетчик отработки красящего вещества. Еще проблема может быть в главной плате PWB. |
Осуществите чистку драм-картриджа (блока фотобарабана). Если проблема в датчике или плате, то нужно отнести принтер в СЦ на диагностику. |
|
F248 |
Ошибка обработки отпечатываемого материала. |
Перезагрузите принтер. Уберите неподдерживаемые спецсимволы из отпечатка. Обновите ПО принтера Kyocera. Смените режим работы принтера с PDL на GDI (Пуск -> Принтеры -> Свойства -> Параметры устройства). |
|
PF |
Отсутствует бумага в лотке подачи. |
Загрузите листы бумаги во входной лоток. Если принтер по-прежнему не печатает, значит нужно искать проблему в чем-то другом. |
|
1101 |
Ошибка сканирования через сеть из-за неправильного имени SMTP сервера. |
Пропишите DNS-адреса помимо прочих настроек печати по сети. |
|
1102 |
Некорректная настройка сканера для работы через сеть |
Зайдите в Web-панель управления принтером (нужно в адресную строку браузера ввести iP принтера Kyocera). Далее в зависимости от модели введите логин и пароль (Admin/Admin или просто admin00 без логина). Далее следуйте инструкции:
Логин и пароль нужны обязательно, если их нет, то следует создать. |
|
2101 |
Ошибка передачи данных при сканировании через сеть. |
Правильно настройте параметры (как для ошибки 1102), только предварительно отключите на ПК антивирус и брандмауэр. |
Если Вы испытали все способы, но не смогли убрать ошибку, то следует нести печатающее устройство в сервисный центр. Кроме того, есть ряд ошибок (высвечиваемых на дисплее принтера), которые нельзя устранить в домашних условиях. Соответствующие коды ошибок принтеров Kyocera представляем в очередной таблице.
Коды ошибок принтеров и МФУ Kyocera, которые нужно устранять в сервисном центре
|
Код ошибки |
Значение ошибки |
Решение проблемы |
|
0030 |
Неисправность платы управления факсом принтера. |
Замена платы. |
|
0100 |
Неисправность платы управления или флеш-памяти принтера. |
Замена платы. |
|
0120 |
Ошибка чтения mac-адреса из-за неисправности флеш-памяти принтера. |
Замена платы. |
|
0190 |
Неисправность платы управления или флеш-памяти принтера. |
Замена платы. |
|
0630 |
Неисправность платы управления принтера. |
Замена платы. |
|
1020 |
Неисправность мотора, привода или отсутствие контакта. |
Разборка принтера и замена изношенных частей. Проверка надежности подключений, замена разорванных (прогоревших) кабелей. Ремонт или замена привода мотора. |
|
1040 |
Неисправность мотора, привода или отсутствие контакта. |
Разборка принтера и замена изношенных частей. Проверка надежности подключений, замена разорванных (прогоревших) кабелей. Ремонт или замена привода мотора. |
|
2000 |
Неисправность главной платы управления, соединительного кабеля или привода принтера. |
Проверить ремни, шестерни и ролики привода. Смазать или заменить, если есть дефекты. Заменить привод или главную плату. |
|
3100 (C3100) |
Неисправность главной платы, привода сканера, датчика положения или нарушение целостности соединений. |
Проверить наличие разрывов и отсутствия контакта. Смазать или заменить изношенные элементы привода. Заменить привод, главную плату, датчик или соединительный кабель. Если Вам повезло, то возможно забыли отключить фиксатор блока сканера. |
|
3101 |
Сетевой кабель не подсоединен, или нарушена работа концентратора. Еще может быть из-за наличия вирусов в системе или неправильно заданным параметрам сервера SMTP. |
Проверить соединения, правильно настроить параметры сети. |
|
3300 |
Неисправность главной платы, датчика CIS или соединительного кабеля. |
Проверить контакты, заменить плату или датчик. |
|
3500 |
Неисправность главной платы или нарушение соединения контактов. |
Проверить контакты, заменить плату. |
|
4000 (C4000) |
Неисправность главной платы, привода сканера или нарушение соединений. Однако чаще всего ошибка лазера. |
Проверить контакты, заменить плату или привод блока сканера. Почистить лазер, смазать ось полигон-мотора, либо полностью заменить блок лазера. |
|
4200 |
Неисправность главной платы, блока сканера или датчика BD. |
Отключить питание принтера на 30 минут. Если не помогло, то следует заменить привод сканера или главную плату принтера. |
|
6000 (С6000) |
Неисправность главной платы, термостата, печки или нарушение соединения контактов. |
Проверить и поправить контакты. Заменить фьюзер. Ремонт или замена печки, термодатчика, термопредохранителя и т.д. |
|
6020 |
Сгорание термистора или главной платы. |
Замена термистора или главной платы. |
|
6030 |
Неисправность главной платы, термостата или термистора. Возможно, причина в отсутствии контакта. |
Проверить соединения. Заменить плату, термостат или термистор. |
|
6400 |
Неисправность главной платы, отсутствие питания или контакта. |
Заменить плату или источник питания. |
|
F000 |
Неисправность главной платы или отсутствие контакта. |
Проверить соединение ремня безопасности. Заменить ремень или плату управления. |
|
F020 |
Неисправность элементов памяти принтера. |
Перезагрузить принтер. Если ошибка не устранилась – заменить плату управления. |
|
F040 |
Неисправность главной платы принтера. |
Перезагрузить принтер. Если ошибка не устранилась – заменить плату управления. |
|
F05D |
Неисправность главной платы. Сбой программного оборудования привода. Проблемы с прошивкой принтера Kyocera. |
Перезагрузить принтер. Если ошибка не устранилась – заменить плату управления. Перепрошить принтер Kyocera. |
|
F245 F246 F247 F375 |
Принтер Kyocera заблокирован из-за проблемы, вызванной отказом источника питания. |
Нужно перепрошить принтер специальной сервисной микропрограммой. |
Обратите внимание: Если у печатающего устройства нет дисплея, то определить проблему можно по светодиодным индикаторам, встроенным в панель управления принтером. Например, у Kyocera Ecosys P2135D нужно сосчитать количество миганий индикаторов красного цвета и таким образом определить число, указывающее на ту или иную ошибку. В свою очередь, у модели Kyocera FS-1040 все зависит от темпа мигания светодиода с надписью «Внимание!» («Attention!»):
- Мигает медленно – указывает на отсутствие бумаги в лотке или тонера в картридже.
- Мигает быстро – оповещает о проблеме с памятью устройства, переполненном лотке или замятии бумаги, а также об использовании неоригинальных расходных материалов.
- Горит постоянно – говорит о проблемах с картриджем или фотобарабаном либо указывает на открытые крышки принтера.
Чтобы потребитель мог наверняка определить проблему, рекомендуем использовать утилиту Kyocera Client Tool, которая идет в комплекте с драйверами принтера.
Ваше Имя:
Ваш вопрос:
Внимание: HTML не поддерживается! Используйте обычный текст.
Оценка:
Плохо
Хорошо
Введите код, указанный на картинке:
