Мавик мини ошибка 40003

Gimbal motor overload error

Few things are as frustrating for drone pilots as a gimbal motor overload error (code 40003). After all, the gimbal is a key piece of equipment that allows the drone pilot to navigate, shoot video, and take photos. Thus, a malfunctioning gimbal essentially renders the drone useless.

So, what exactly is a gimbal overload error, and what causes it? In this guide, we will discuss this common error in-depth, and we will also provide a troubleshooting guide so you can fix the problem and get your DJI Mini 2/DJI Air 2S/Mavic Air 2/Mavic Mini or Phantom up in the air.

What Is The Gimbal Overload Error?

When the display shows that there is a gimbal motor overload, and you may get an error code 40003, it simply means that something is inhibiting the gimbal’s movement which causes the gimbal motor to be strained. It is important to address this error quickly, as excessive strain can cause lasting damage to the gimbal’s motor. 

It is also worth mentioning that this error can happen both on the ground and in flight.

What Causes DJI Gimbal Motor Overload?

There are several things that can cause a gimbal motor overload error. Here we will discuss these culprits.

Launch Site Obstruction

The most common culprit is tall grass or something else on the ground in close proximity to the gimbal. If the drone is attempting its startup sequence in tall grass, the grass can prevent the gimbal from achieving the full range of motion necessary to properly calibrate. 

Forgetting To Remove The Gimbal Cover

You can also get a gimbal motor overload error if the gimbal cover is still on while the drone is powered on. The gimbal cover is only meant to protect the gimbal while the drone is in transit or not being used. If the cover is still in place when the drone is turned on, it will limit the gimbal’s range of motion, preventing it from completing its calibration sequence. 

mavic air 2 gimbal cover

It will happen to every drone pilot eventuallyexcitement gets the better of you, and you rush through your preflight checklist, turn the drone on, and are ready to get up in the air…but the gimbal cover is still on. You realize your mistake when you hear the gimbal hitting up against the cover as it tries to calibrate, and a gimbal motor overload error flashes on your device. I speak from experience here…

Debris Stuck In The Gimbal

drone on the ground

If you take off from sandy or dusty surfaces, it is possible for small pieces of debris to get lodged in the gimbal. The gimbal is a very sensitive piece of equipment, so even the smallest of obstructions can prevent it from moving correctly which will trigger this error message.

Third-Party Accessories

Using non-approved third-party accessories on the gimbal can also result in this error message. 

Third-party accessories are accessories that are not produced by the drone manufacturer. If the manufacturer releases an accessory for a drone (in this case, the Mavic or Phantom), it is guaranteed that the accessory will not adversely affect the drone’s performance or operational capabilities.

mavic air 2 nd filters

However, third-party accessories can sometimes cause problems. While they might fit the drone perfectly in terms of dimensions, the material used might be too heavy or might otherwise compromise the drone’s performance. For example, some ND filters might add too much weight to the gimbal, causing excess strain on the gimbal motor. 

Strain On The Gimbal During Flight

You can also get this error message while in flight. Sudden movementsnamely yaw movementswhile flying fast (such as in Sport Mode) can trigger this error. Remember, the gimbal and the gimbal motor are extremely sensitive, so the g-forces associated with fast flight maneuvers can strain the gimbal motor as it tries to keep up.

Faulty/Broken Hardware

Lastly, you might get this error message if the gimbal and/or gimbal motor have faulty or broken hardware. If your drone has crashed at some point, the gimbal likely sustained damage. 

Here we will discuss the troubleshooting steps you should follow if you experience a gimbal motor overload error on your DJI Mavic or Phantom.

Step 1: Ensure That The Ground Is Clear Of Obstacles

When powering on your drone, if you get a gimbal motor overload error, the first thing to do is ensure that the ground around the gimbal is clear of obstacles. If the drone is not on flat, clear ground, power it off, move it to a flat and open area, and turn it back on. If the error is gone, it means something on the ground was previously interfering with the gimbal’s range of motion.

drone preflight check

To prevent this altogether, we suggest always powering the drone on when it is on flat ground or a launchpad. It is a good idea to always visually inspect the area around the gimbal for anything that might interfere with the gimbal’s movement. This will ensure that the gimbal will be unobstructed during its calibration sequence. 

Step 2: Check For Debris In The Gimbal

If motor overload error persists after you confirmed that the launch site is clear of obstacles, there might be debris in the gimbal. As mentioned, sand, dust, and other small particles can get lodged in the gimbal’s joints. Power the drone off and blow on the gimbal to remove any debris. Then, turn the drone back on.

Step 3: Ensure That Third-Party Accessories By The Gimbal Aren’t Too Heavy

If you are not using any third-party accessories with your drone (i.e. ND filters, an anti-glare hood, etc.), go ahead and skip to the next step.

If you are using a third-party accessory, turn the drone off, remove the accessory, and turn the drone back on. If the error message is no longer displayed, the third-party accessory was the likely culprit.

If you are using several third-party accessories located by or on the gimbal, turn the drone off, remove one accessory, and turn it back on. Repeat this process until you have identified which accessory was causing the problem.

If there is any doubt about what might have been causing the gimbal motor overload error, check online forums and reviews of the accessory in question to see if other people have had similar issues.

Step 4: Calibrate The Gimbal

As with most electronics, some errors seemingly happen for no reason at all. If this error has persisted up to this point, chances are it can be fixed by simply calibrating the gimbal.

Calibrating the gimbal is a quick and easy procedure that can be done on the DJI GO 4 or DJI Fly app. The gimbal calibration process is virtually the same for the Mavic and the Phantom. Just follow these steps:

  • Tap on the three dots in the upper right corner of the screen.
  • Tap on the gimbal symbol.
  • Select gimbal calibration.
  • A message will appear prompting you to ensure that the aircraft is level and that nothing is obstructing the gimbal’s range of motion. Ensure that the drone is level and that nothing is obstructing the gimbal.
  • Select OK, and the gimbal calibration process will begin.

Step 5: Fly Less Aggressively

If you get a gimbal motor overload error while your Mavic or Phantom is in flight, it is more than likely a result of aggressive flying. To remedy this, simply fly slower, and refrain from conducting quick maneuvers that might strain the gimbal. 

While the Mavic and Phantom are incredibly adept at flying, it is important to remember that they are not racing drones; they are first and foremost flying cameras.

Step 6: Send The Drone To DJI

If all else fails, unfortunately, your drone will need to be repaired by DJI. 

It is possible to fix faulty or broken hardware on your own, but it requires a high level of skill and competence in working with electronics. Since most people simply do not have the experience or skill required for such repairs, it is better to send it in for repair. 

Furthermore, there could be an underlying software issue causing the error, and this is something only DJI can fix.

In Closing

We hope this guide has helped you better understand what the gimbal motor overload error is, what causes the error, and how to troubleshoot it on the DJI Mavic and Phantom. 

As far as aerial photography and cinematography go, the drone’s gimbal is what makes it pop. It utilizes calibrated electronic motors and intelligent sensors which automatically compensate for any movement the computer detects across all three axes.

Gimbals also reduce vibration and keep your camera stable despite the drone’s movement. All these parts conspire together to give us some of the smoothest and most unique images captured today in pictures or videos. 

Drone gimbals are very sensitive, and a variety of issues could develop when calibrating or flying your drone.

In this article, we’re going to help you identify and resolve the major gimbal issues encountered when piloting your DJI Mini 2. Don’t miss it!

Best Drone Courses for Beginners (Part 107 & More)

Gimbal Motor Overload (Error code 40003)

The first gimbal error we’ll look at is a very common one and is also usually an easy fix.

It comes up when the gimbal struggles or is unable to support the camera or camera lens. This can cause the camera to vibrate or shake erratically, leading to poor images.

1. Gimbal Obstruction

The gimbal overload error could arise when starting up your drone and your gimbal is blocked by a foreign object.

This will affect the startup sequence and calibration of your drone gimbal and lead to an overload error.

To avoid this, ensure that before takeoff, there is plenty of clearance, and be aware of your surroundings to make sure the object is blown toward the takeoff point of your drone.

Get rid of any foreign objects found around your drone before takeoff and moving forward, try to get a landing pad.

I would say this is probably one of the most essential tools to have as far as drone safety and preventive maintenance is concerned.

Our Pick

Drone Landing Pad

Drone Landing Pad

DJI Mini 3 Pro, DJI Mavic 3, Mavic Air 2, Mavic Mini 2, Mavic 3 Pro/Zoom, Fast-Fold Helipad for DJI Air 2s/DJI FPV Double-Sided Waterproof, 25 inch (65cm).

Buy from Amazon

We earn a commission if you make a purchase, at no additional cost to you.

05/20/2023 11:19 am GMT

2. Heavy Accessories

Adding third-party accessories such as ND filters and lens filters could add extra weight that the gimbal cannot support.

Improper installation of these accessories could also affect the weight and balance of the gimbal, leading to an overload error.

To resolve this, make sure all filters are properly fitted and installed onto the camera and make sure to only purchase accessories made by DJI or DJI-approved manufacturers for the DJI mini 2.

Generic filters (one-size-fits-multiple) are usually not the best options. Also, be more specific when selecting your accessories.

Weight distribution has a huge effect on the balancing and leveling of your gimbal. If you still see the overload, try taking off without the accessories.

3. Debris

Over time, as you fly your drone more and more, dust, dirt, and other foreign materials build up in between the gimbal arms.

This debris adds extra weight to the gimbal and impinges on the freedom of movement of the gimbal arms, leading to flutter(vibrations) and a gimbal overload error.

Get a compressed air duster or an air blower pump and use it to flush out any debris between the arms of your drone gimbal.

Be careful when holding or rotating the gimbal, and gently feel for any roughness or limitations when trying to rotate the gimbal about its axis. Then use the air duster appropriately to flush out debris.

You can find a very helpful tutorial video below to guide you.

4. Loose or Damaged Hardware

Hard landings, crashes, and landing on uneven terrain could damage or at the very least, knock parts out of alignment.

Inspect your drone, ensure no loose screws or fixtures, and adjust accordingly should you notice anything out of order.

If the damage is too much to fix with your tightening of screws or fitting parts in place, then a gimbal replacement would most likely be needed.

5. Gimbal Cover

It might seem silly to some, but this is actually one of the most common mistakes made by pilots.

If left on during startup, a gimbal cover will restrict the gimbal movement and give the overload error. The gimbal cover is only meant to protect the gimbal while the drone is in transit or not being used.

If left on, the gimbal calibration sequence will not be completed, and an overload error could be encountered. If this happens repeatedly, the gimbal motor is in serious danger of burning out, rendering it useless.

To prevent this, always take off your gimbal cover when setting up your drone for takeoff (make a takeoff checklist if you must).

The DJI gimbal stuck error appears when something hinders the gimbal’s movement. This is pretty similar to the gimbal overload error in terms of causes and solutions.

Still, the main thing to notice with this error is that the gimbal movement is restricted entirely.

Causes: Most of the causes of the gimbal stuck error are similar to those of the gimbal overload error, so please refer to the list above and resolve accordingly.

Note: The leading causes for error codes 40002 and 40003 are mechanical and hardware-based, but before and after troubleshooting, a successful gimbal calibration should be done. Before doing this, ensure your firmware is up to date to avoid any calibration errors.

Gimbal Calibration Error (Error code 40021)

As you would have as guessed, Error Code 40021 occurs when there is an unsuccessful calibration of the drone gimbal. This is commonly due to hardware issues such as those which could lead to the errors 40002 or 40003.

Visually inspect the gimbal and camera for damage.

Should your gimbal be in good condition with no physical damage to the hardware, then scroll up and follow the steps listed above and then recalibrate your drone gimbal.

How To Calibrate Your Gimbal Correctly

  1. Make sure the drone battery and controller are charged to an adequate level, preferably above 50 percent each.
  2. Place the aircraft on a flat, level surface and power on the aircraft.
  3.  Clear the area of any obstacles or debris, and place the drone on the landing pad if available.
  4. Launch the DJI Fly app and ensure the app and firmware are up to date.
  5. In the Live View on your phone or smart controller, select the three dots () in the upper right corner to open the menu.
  6. Switch to the control tab, and scroll down to gimbal calibration.
  7. In the prompt that comes up, you can choose between Automatic and Manual Calibration.
  8. Your Mini 2 will automatically start to realign the gimbal. The calibration process is not a long one and should take no more than a few minutes. Once completed, the successful prompt should come up, and you can now fly your drone.
  9. If you are unsuccessful with the automatic calibration, or you find yourself dissatisfied with the results, restart the calibration process above, and when asked, select MANUAL instead of automatic calibration.
  10. On your screen, you should have two fields for horizontal and yaw angles with the possibility to increase or decrease the value.
  11. Pick an object or the horizon in front of you as a reference and adjust the gimbal horizontal/yaw angles till the view is level and to your satisfaction.

In the case where after a visual inspection of the drone, you noticed visible damage, you will need to replace your gimbal.

Replacing drone parts or making repairs on your own is very delicate, and we recommend seeking help from a professional, preferably by contacting DJI technical support or by reaching out to an authorized technician.

Some of you may choose to do the repairs yourself. We’d recommend avoiding that unless you’re very good with your hands, have the required tools, and can get access to authentic DJI parts.

DJI Mini 2 Drone Gimbal Replacement

Should you open up your drone and perform repairs yourself, you will most definitely void your warranty, so be careful! No matter how experienced you are, this is a semi-expensive piece of equipment, so treat the gimbal with care.

After the gimbal replacement, calibrate your drone and gimbal and then try to fly. If an error prompt comes up, try a full factory reset of the drone before seeking professional help.

Required tools: Amazon Basics 32-Piece Electronics Repair Screwdriver Set (see below).

Amazon Basics Electronics Repair Screwdriver Set

How to Factory Reset your Drone and Controller

Before making any hardware changes to your drone and even after, ensure there are no software issues and the firmware of your DJI Fly app and drone are compatible and up-to-date.

A factory reset could also help. Here’s how to go about it:

  1. First, download and install the DJI Assistant 2 program on your device.
  2. Connect your drone to your laptop, and wait for the software to detect your drone.
  3. You’ll be able to see your drone on the Connected Devices screen. Select your drone. 
  4. Click on Firmware Update.
  5. After that, you’ll be able to see the “Restore factory defaults” button.
  6. Click on the factory reset button and confirm when you are asked to confirm the reset. A progress bar will pop up. Do not disconnect until the process is completed successfully.
  7. Calibrate the drone and gimbal after resetting before use (follow the steps above).

Gimbal Unable to Connect (Error 40012) and Gimbal IMU data error (Error 40021)

 Error 40012 and 40021 are issues that commonly arise after the replacement of the drone gimbal or the replacement of the camera.

If your hardware replacement was done by DJI or an authorized technician, then try updating or downgrading firmware depending on which is suitable for your drone and phone.

If problems persist, return the drone to the service center.

It’s most definitely a software issue, and DJI has its specific program for resolving issues like this. It arises because DJI parts have unique IDs, and changing parts leads to a desynchronization of paired components.

For example, the IMU–which is a device that measures and reports the specific gravity and angular rate of an object to which it is attached–has a unique ID attached to it that matches that of the gimbal attached to the drone from production.

Should the gimbal be replaced, the new gimbal will need to be synced with the IMU of the drone (the leading cause of error 40021).

If your gimbal replacement was a DIY project, refer to the videos below for some insight on how to resolve this.

If you’re more of a hardware technician than a software (programming) whiz, you will have to visit a professional.

Note: The average cost of DJI gimbal replacement with labor could be up to $400 with DJI or an approved technician, and if done by yourself could be about $100 to $200 cheaper.

Hopefully, you never run into any of these errors or at least any serious ones, but I hope we’ve been able to enlighten you on various gimbal-related issues on your DJI drone and how to fix them.

Talkenrain


  • #1

Greetings, this is my first real contribution to this forum. Hopefully it’s helpful to others as I could find little info for my particular problem. I’m new to the MA2 but not new to drones. I’ve been flying them on and off for a while and have gotten reasonable good at it. So when I received the MA2 I thought it’s pretty much like my previous DJI drones. I started taking it everywhere and using it just about every day. I’d typically launch from my landing pad unless it’s a last minute thought, i’d say 70% of the time. the other 30% I’d search for a clean patch of pavement just to stay clear of dust in the drone (although it’s never been an issue in the past). I’d typically use a ND8 or 16 filter for daylight shots and go without a filter when the light level is not so bright (habits from previous drones with and without camera settings controls). Here is where my problems began with the MA2. If you’ve ever changed a filter on the MA2, you know the mount is different. it’s a short twist to remove and install filters inside 4 guides holes of the camera housing. The first time I removed the factory ring to install a filter is when I discovered the ring actually has no protective glass, it just more or less is a beauty ring to make the camera look complete (so I thought). Because I usually fly with a filter, i didn’t think much of the ring, threw it in my bag. Whenever I needed a filter I’d put one on but when I didn’t, i wouldn’t bother to install the empty ring…

This evening I decided to video the local TV towers just before dusk. I did my usual (removed my daylight ND filter and because I was in a hurry to beat the sun going down, I took off without my landing pad). Well, I noticed right away the gimbal was intermittently responsive then I got the error code 40003 gimbal motor overload and the 40002 gimbal stuck error code but then the message quickly went away. A little concerned i went forward with my flight but quickly noticed the gimbal not being smooth and would ether get stuck or jumpy… I landed the drone, turned it off and checked for free movement of the gimbal. it seemed ok so I powered it up and flew my mission without problems until I was making my final loop and it gave a stuck gimbal message again. I landed and this time tried calibrating the gimbal. it failed and I started to see visions of being without the drone for the remainder of our short summers. I got on line and started searching this code pertaining to the MA2. I found very little about these codes but the more I read the more I was sure I had not done any of the things others had done to get these messages (so I thought)…

My wife starts telling me, maybe you hit something or some how got things out of alignment. Then she says maybe you flew through a dust cloud or something. Well, She was kind of right but I think more of a flaw in the camera design. Apparently those holes in the camera head that a filters attaches to go all the way through to the vertical gimbal mechanism so flying (in my case taking off without a landing pad) without the beauty ring installed allowed enough dust, dirt or sand to get inside the housing and prevent the gimbal from free vertical movement.I don’t see any other openings in the gimbal that could allow anything into the camera head but i just dont understand why the holes go all the way through the gimbal hardware. I tried blowing it out but that didn’t work but with a can of compressed air seemed to do the trick. Its now works again 100% again, calibrates and I’m back to smooth movements without issues. The amount of dust that came out was so small it was undetectable but it apparently does not take much to completely disable the gimbal.

The moral to this story; NEVER LEAVE THE CAMERA HEAD OF A MA2 WITHOUT A FILTER OR THE BEAUTY RING INSTALLED !!!

I’m serious, there has been only a few times I’ve not used a landing pad and I usually make sure the area is clean of rocks or loose particles. it’s never been to a beach and really has been treated the same as my other drones that have not had this kind of issue…

  • #2

I’ve had several drones with the yuneec being my fav but I can’t get parts for it now. Have had several others but never a DJI. Its only 3 weeks old and always takes off and lands on my driveway. I’ll try the canned air and maybe that will work. I don’t think the mini mav has a filter attachment. Thanks for the tip.

  • #3

I’ve had several drones with the yuneec being my fav but I can’t get parts for it now. Have had several others but never a DJI. Its only 3 weeks old and always takes off and lands on my driveway. I’ll try the canned air and maybe that will work. I don’t think the mini mav has a filter attachment. Thanks for the tip.

The mini filters clip over the top of the camera so totally different. The mini has no holes in the front.

Talkenrain


  • #4

I’ve had several drones with the yuneec being my fav but I can’t get parts for it now. Have had several others but never a DJI. Its only 3 weeks old and always takes off and lands on my driveway. I’ll try the canned air and maybe that will work. I don’t think the mini mav has a filter attachment. Thanks for the tip.

Good luck . I had to blast air into mine several times to get it working 100% smooth again.

  • #5

thanks for sharing, it was a long read.

FYI I’ve had gimbal overload, jumpy / shaking video and overall gimbal failure. I’ve not taken out the filter placeholder in 97% of the flights I have, ie I’ve only flown with the filter in 2 flights, and the rest of them with the placeholder in place in at least 40 flights by now.

My gimbal just fails / shows overload readings with it being very loose and not binding at all in any axis or direction.

Also, I’m pretty sure MOST of the people who have had this failure (and I’m trying to keep track as I’m very dissatisfied that DJI still does not make a good gimbal after all these years, and I actually suffered from a bad series of Mavic Pro 1 gimbal failure, hence the reason for «upgrading») does not fly without that decorative piece.

Maybe, it is still related as you say, as the holes / gaps are not airtight and through time and wind dust COULD get in and do damage. But I’m not 100% sure as I’ve not dismantled the gimbal enough to see through the insides.

  • #6

Blasted air in mine yesterday and it did good on the first battery but when I went back up got the 40003 and gimbal stuck but they were both working good. Also does the filter come with the drone or are they an add on?

  • #7

Blasted air in mine yesterday and it did good on the first battery but when I went back up got the 40003 and gimbal stuck but they were both working good. Also does the filter come with the drone or are they an add on?

Not sure i follow. Does it work good or is it still stuck?

The filters come with the Fly more combo. Which I have.

Talkenrain


  • #8

RE: dirt/dust.
It really doesn’t take much in the wrong place to affect the vertical movement of the gimbal (seems to be very very small gears). If you have the camera recording with a high frame rate while taking off from the ground, for just a few frames you’ll see an amazing amount of dirt and dust kicked up (just after starting the blades) even when you’re in a what appears to be a clean area (like a driveway). Now part of my pre-flight is to always make sure I have the beauty ring in place or a filter mounted and always use a launch pad or take off (and/or landings) or alternately use my hand. It’s just so much cleaner. I’ve not had this issue again since I made these simple changes.

Just my 2¢

Talkenrain


  • #9

Blasted air in mine yesterday and it did good on the first battery but when I went back up got the 40003 and gimbal stuck but they were both working good. Also does the filter come with the drone or are they an add on?

I had to blast mine a number of times from all angles to get it back to 100%. Be patient. it could be as small as a few grains of sand causing the issue.

  • #10

I had to blast mine a number of times from all angles to get it back to 100%. Be patient. it could be as small as a few grains of sand causing the issue.

You could maybe even blast it again with air and keep it on the ground and move the gimble around some then blast again… do it a few times until it works itself free. Save some time maybe.

Hope you get it fixed….

  • #11

Hey. I am having the same problem. Gaves me error code 40003 and 40004. When i turn it on the gimbal does its thing and moves with no problem but it doesn’t respond to the controller. I flew it close to a beach so there were some sand. Any thoughts?

  • #12

Hey. I am having the same problem. Gaves me error code 40003 and 40004. When i turn it on the gimbal does its thing and moves with no problem but it doesn’t respond to the controller. I flew it close to a beach so there were some sand. Any thoughts?

Hi I have a Mavic Air and am also havig issues with gimble over heating warnings. This only seems to happen when rotating it downward for a closer view using the finger control. I returned it to home base cleaned it with canned air and back up in the air only to have the warning come back on again. I have since returned it homr for a thorough cleaning hoping the next flight will be better. If this continues should i send it back — I have extended care. Thanks

When I was looking solution for a DJI Mavic Mini Error code, I found that there are many, unique DJI Mavic Mini error codes compared to other DJI drones. So I thought to research DJI Mavic Mini/ Mini 2 Error codes and what they mean.

Also, I thought it would be helpful and friendly to write an article that would be helpful for Mavic Mini users, about almost every DJI Mavic Mini / Mini 2 code and how to fix those issues. Hopefully, this article would help with figuring out the Error code and how to fix it.

  • Error 1: DJI Mavic Mini error code 10001.
  • Error 2: DJI Mavic Mini error code 10016.
  • Error 3: DJI Mavic Mini error code 10022.
  • Error 4: DJI Mavic Mini error code 10023.
  • Error 5: DJI Mavic Mini error code 30007/ 30008.
  • Error 6: DJI Mavic Mini error code 30047.
  • Error 7: DJI Mavic Mini error code 30049.
  • Error 8: DJI Mavic Mini error code 30050/ 30055.
  • Error 9: DJI Mavic Mini error code 30060.
  • Error 10: DJI Mavic Mini error code 30064.
  • Error 11: DJI Mavic Mini error code 30085.
  • Error 12: DJI Mavic Mini error code 30105.
  • Error 13: DJI Mavic Mini error code 30128.
  • Error 14: DJI Mavic Mini error code 30142.
  • Error 15: DJI Mavic Mini error code 30168.
  • Error 16: DJI Mavic Mini error code 30210.
  • Error 17: DJI Mavic Mini error code 30224.
  • Error 18: DJI Mavic Mini error code 30226.
  • Error 19: DJI Mavic Mini error code 40002.
  • Error 20: DJI Mavic Mini error code 40011.
  • Error 21: DJI Mavic Mini error code 40012.
  • Error 22: DJI Mavic Mini error code 40021.
  • Error 23: DJI Mavic Mini error code 180016/ 180030/ 180031.

Error 1: DJI Mavic Mini error code 10001.

DJI Mavic Mini error code 10001 stands for “Camera Malfunction, Repairs required”. You need DJI Support to fix this issue. Therefore you need to shut down the Mavic Mini aircraft and contact DJI Support for repairing or replacing the camera. Many users have got this error after crashing the Mavic Mini.

Error 2: DJI Mavic Mini error code 10016.

DJI Mavic Mini error code 10016 stands for “Camera not calibrated, Image quality can be affected”. The best option to fix this issue is to calibrate the Mavic Mini camera.

How to Calibrate DJI Mavic Mini Camera.

  1. Place the Mavic Mini aircraft on a flat surface and power on the Mavic Mini aircraft and controller.
  2. Open the DJI Fly app and enter the camera view.
  3. Click on three dots on the top left corner and tap on the camera icon.
  4. Go to Camera Gimbal Advanced Settings > Auto Calibrate Gimbal and hit OK.
  5. Wait until the process succeeds.

Error 3: DJI Mavic Mini error code 10022.

DJI Mavic Mini error code 10022 stands for “No SD card. Insert SD card”. If you have already inserted the SD card, check whether the SD card is a Supported SD card with DJI Mavic Mini. Else use an SD card that supports DJI Mavic Mini. If you are using a compatible SD card, try formatting the SD card.

Error 4: DJI Mavic Mini error code 10023.

DJI Mavic Mini error code 10023 stands for “SD card malfunction, Change card”. Try inserting another SD card or try formatting the SD card. Also, you can try repairing the SD card before inserting it.

How to Repair DJI SD Card.

  1. Connect the SD card to the PC and open the command prompt.
  2. Then type “chkdsk” and leave a space and specify the SD card driver letter (Ex: chkdsk D). and hit enter.
  3. Once the process is done the sd card is repaired.

Error 5: DJI Mavic Mini error code 30007/30008.

DJI Mavic Mini error code 30007/30008 stands for “No GPS Signal”. There are thousands of questions in the DJI forums asking about this error and found many pilots able to fix the issue by performing the below steps.

  • Update DJI Mavic Mini Firmware.
  • Uninstall the DJI Fly app and install it again.
  • Connect to a strong internet connection.
  • Contact DJI Support.

Error 6: DJI Mavic Mini error code 30047.

DJI Mavic Mini error code 30047 stands for “Barometer initialization failed. Restart aircraft”. As it said to fix this issue, Restart the Mavic Mini aircraft. Also try updating the Mavic Mini firmware.

Error 7: DJI Mavic Mini error code 30049.

DJI Mavic Mini error code 30047 stands for “GPS Module error.  Restart aircraft”. Restart the Mavic Mini aircraft to fix this issue. If it still keeps happening update the Mavic Mini firmware or contact DJI Support.

Error 8: DJI Mavic Mini error code 30050/ 30055.

DJI Mavic Mini error code 30050/ 30055 stands for “IMU Calibration required.  Calibrate IMU”. Calibrate the IMU properly to fix this error.

How to Calibrate DJI Mavic Mini IMU.

  1. Open the DJI Fly app and enter the camera view.
  2. Tap on the top left corner three dots and open the main menu.
  3. Scroll down and visit Sensors > IMU and hit calibrate.
  4. Once the IMU calibration process started, the DJI Fly app would instruct you to place the aircraft in different positions. Follow those instructions to calibrate the IMU.

Error 9: DJI Mavic Mini error code 30060.

DJI Mavic Mini 30060 stands for “Compass error”. To fix this error keep the Mini aircraft away from metal or magnetic objects, and calibrate it before use.

Error 10: DJI Mavic Mini error code 30064.

DJI Mavic Mini 30064 stands for “Unable to Takeoff”. First, check whether the Mavic Mini is in a geofenced area. If it’s not try restarting the aircraft. If it’s still happening, update or refresh the Mavic Mini firmware.

How to Update DJI Mavic Mini Firmware Using DJI Fly app.

  1. Open the DJI Fly app and enter the camera view.
  2. Tap on 3 dots at the top right-hand corner and visit the About tab.  
  3. Click “Check for updates”.
  4. If a new firmware is available, update the firmware to the latest.

Error 11: DJI Mavic Mini error code 30085.

DJI Mavic Mini error 30085 stands for “ESC Connection error”. To fix ESC (Electronic Speed Controller) error there are two possible solutions. They are,

  1. Update Mavic Mini firmware.
  2. Contact DJI Support to repair or replace the ESC.

Error 12: DJI Mavic Mini error code 30105.

DJI Mavic Mini error 30085 stands for “Navigation System Error, Restart the aircraft”. First, try restarting the aircraft. If it doesn’t fix the issue try calibrating the IMU. If Calibrating IMU also didn’t fix the error contact the DJI Support.

How to Calibrate DJI Mavic Mini IMU.

  1. Open the DJI Fly app and enter the camera view.
  2. Tap on the top left corner three dots and open the main menu.
  3. Scroll down and visit Sensors > IMU and hit calibrate.
  4. Once the IMU calibration process started, the DJI Fly app would instruct you to place the aircraft in different positions. Follow those instructions to calibrate the IMU.

Error 13: DJI Mavic Mini error code 30128.

DJI Mavic Mini error 30128 stands for “Propeller rotating too fast”. Many users have explained that this is an effect of bend propellers and could be fixed by replacing the DJI Mini propellers.

Error 14: DJI Mavic Mini error code 30142.

DJI Mavic Mini error 30142 stands for “Motor unable to rotate. Check motors”. Try restarting the aircraft and updating the firmware.

Error 15: DJI Mavic Mini error code 30168.

DJI Mavic Mini error 30128 stands for “Aircraft power insufficient“. Charge the aircraft battery to a sufficient level before flying the Mavic Mini.

Error 16: DJI Mavic Mini error code 30210.

DJI Mavic Mini error 30128 stands for “Power System Hardware Error”. Contact DJI Support to repair the Power System.

Error 17: DJI Mavic Mini error code 30224.

DJI Mavic Mini error 30128 stands for “Incompatible Firmware Verison”. To fix this error there are two steps to follow.

  1. Clear the DJI Fly app cache and app data. Then update the DJI Fly app.
  2. Update the DJI Mavic Mini firmware.

Error 18: DJI Mavic Mini error code 30226.

DJI Mavic Mini error 30128 stands for “Start failed.  Restart aircraft and DJI Fly app. As it sounds to fix this error, restart the Mavic Mini aircraft and DJI Fly app.

Error 19: DJI Mavic Mini error code 40002.

DJI Mavic Mini error 30128 stands for “Gimbal stuck”. Check whether the gimbal cover is removed and ensure can rotate freely. Also, be sure to remove the gimbal cover before powering on the aircraft.

Error 20: DJI Mavic Mini error code 40011.

DJI Mavic Mini error 30128 stands for “Gimbal Calibration error”. To fix the Gimbal Calibration error try restarting and calibrating the gimbal. Also, try updating the Mavic Mini firmware.

How to Calibrate DJI Mavic Mini Camera.

  1. Place the Mavic Mini aircraft on a flat surface and power on the Mavic Mini aircraft and controller.
  2. Open the DJI Fly app and enter the camera view.
  3. Click on three dots on the top left corner and tap on the camera icon.
  4. Go to Camera Gimbal Advanced Settings > Auto Calibrate Gimbal and hit OK.
  5. Wait until the process succeeds.

Error 21: DJI Mavic Mini error code 40012.

DJI Mavic Mini error 40012 stands for “Gimbal unable to connect.  Repairs required”. You have to contact DJI Support to repair or replace the gimbal.

Error 22: DJI Mavic Mini error code 40021.

DJI Mavic Mini error 40021 stands for “Gimbal IMU data error”. You need to contact DJI Support to fix this issue.

Error 23: DJI Mavic Mini error code 180016/180030/ 180031.

DJI Mavic Mini 180016/180030/ 180031 error codes stand for “Sensor error”. Try rebooting the DJI Mavic Mini aircraft.

Понравилась статья? Поделить с друзьями:

Не пропустите эти материалы по теме:

  • Яндекс еда ошибка привязки карты
  • М74 ошибка р2135
  • М74 коды ошибок
  • М7100dn пантум ошибка 3001 после заправки
  • М4109 ошибка бобкет

  • 0 0 голоса
    Рейтинг статьи
    Подписаться
    Уведомить о
    guest

    0 комментариев
    Старые
    Новые Популярные
    Межтекстовые Отзывы
    Посмотреть все комментарии