Miditherm 200 mp bego ошибки

English ⋅ Miditherm MP

en

Malfunction

Time and/or program are no

longer stored

LED

lights up, but furnace

does not get warm

Furnace does not get warm when

«Set Finished time» has been set

«Reducing or increasing temper-

ature in running program» does

not function

Calculated and actual Finished

time deviate significantly from

each other

Jamb brick defective

1)

If an error message occurs (Er XX), an acoustic signal sounds for 3 minutes.

Replacement of a defective thermocouple

48

Cause

Controller defective

Heater defective

Controller defective

Long power failure

The «Start/Stop» button was

pressed.

Voltage fluctuations in the power

network

page 47

Elimination

Replace controller.

Check heater for continuity.

If necessary, replace heating

mould (→ page 49).

Replace controller.

Check in-house power network

for time switching.

* Create new program with desired

final temperature. Start program.

* Carry out correction program

(→ page 42).

Replace jamb brick (→ page 50)

• English ⋅ Miditherm MP 45 85817 BA-en/12 306.01269…/307.00804… en Acoustic signal / cut-out temperature of extraction system At the end of a program an acoustic signal sounds. If desired, the signal can be switched off perma- nently. The Regulus extraction system can be connected to the rear socket. You can set up to what furnace temperature the suction extraction unit is supplied with power . 1. When swit

• English ⋅ Miditherm MP 49 85817 BA-en/12 306.01269…/307.00804… en Replacement of a defective heating mould page 47
  

• 28 85817 BA-en/12 306.01269…/307.00804… English ⋅ Miditherm MP en Table of contents General Information ………………………………………29 Safety Instructions…………………………………………31 Unit description …………………………………………….33 Scope of delivery, wearing parts and extras ……..34 Technical Data………………………………………………34 Installation……………………………………………………35 Program table………….

• 48 85817 BA-en/12 306.01269…/307.00804… English ⋅ Miditherm MP en Replacement of a defective thermocouple Time and/or program are no longer stored Controller defective Replace controller. LED lights up, but furnace does not get warm Heater defective Check heater for continuity. If necessary, replace heating mould (→ page 49). Controller defective Replace controller. Furnace does not get warm when «Se

• English ⋅ Miditherm MP 33 85817 BA-en/12 306.01269…/307.00804… en Unit description Miditherm MP Miditherm laboratory ovens serve for waxing and preheating of casting flasks and duplicate models. They provide users with the facility for using both shockheating and conventional embedding materials. The required finishing time, even for longer periods, can be programmed with the aid of a micro-controller. 1 Ma

• Translation of the original instructions Miditherm 200 MP Miditherm 100 MP en English Miditherm 200 MP 307.00804 Miditherm 100 MP 306.01269
  

• English ⋅ Miditherm MP 43 85817 BA-en/12 306.01269…/307.00804… en Reducing or increasing temperature in running program Example: After the end of the program (LED flashes) the furnace temperature is 800°C. Further heating to 900°C is desired. 1. Keep depressed until LED «°C/min.» flashes. 2. Press (LED «C» flashes). 3. Press until desired temperature appears. 4. Keep depressed until the LED

• 50 85817 BA-en/12 306.01269…/307.00804… English ⋅ Miditherm MP en Replacement of a defective jamb brick Fig. 4 Cleaning page 47
  

• 36 85817 BA-en/12 306.01269…/307.00804… English ⋅ Miditherm MP en Basic principles Displays after unit is switched on 0…3 sec: parameter of the controller > 3 sec: current furnace temperature Furnace care 1. Prior to first use, start program #9 (→ page 41): The furnace heats up to 1050 °C and maintains this temperature for 60 minutes. This results in the formation of a protective oxide layer on the heating wire. 2. Always use the ceramic base. 3. Place the

• English ⋅ Miditherm MP 35 85817 BA-en/12 306.01269…/307.00804… en Installation Fig. 3 Installation Regulus WARNING Installation, site of Installation and start-up • Install unit only on adequately sta- ble and non-combustible surface. • Because of the wax vapours, install the furnace under a chimney stalk as far as possible. Always dis- charge vapours outdoors. • Only use the furnace in dry rooms. • There must not be any combustible objects in the area near the fur- nace. •

• 32 85817 BA-en/12 306.01269…/307.00804… English ⋅ Miditherm MP en Special safety instructions regarding this machine WARNING Installation, site of Installation and start-up • Install unit only on adequately sta- ble and non-combustible surface. • Because of the wax vapours, install the furnace under a chimney stalk as far as possible. Always dis- charge vapours outdoors. • Only use the furnace in dry rooms. • There must not be any combustible

• 30 85817 BA-en/12 306.01269…/307.00804… English ⋅ Miditherm MP en Conventions These operating instructions contain references to residual hazards, important user tips and handling instructions that are identified with the following symbols and words. Warranty and Liability Our general terms and conditions of sale and delivery apply. These are made available to the customer on completion of the contract, at the latest. Warranty a

• English ⋅ Miditherm MP 29 85817 BA-en/12 306.01269…/307.00804… en General Information Importance of the operating Instructions These operating instructions cover all the infor- mation that is necessary according to the relevant regulations for the safe operation of the device described herein. The operating instructions are a part of the machine. The operating instructions should therefore • always be kept at hand near the device until the device is disposed of, • and should be p

• 9, Bego Miditherm 200 MP English ⋅ Miditherm MP 35 85817 BA-en/12 306.01269…/307.00804… en Installation Fig. 3 Installation Regulus WARNING Installation, site of Installation and start-up • Install unit only on adequately sta- ble and non-combustible surface. • Because of the wax vapours, install the furnace under a chimney stalk as far as possible. Always dis- charge vapours o…

• 21, English ⋅ Miditherm MP 47 85817 BA-en/12 306.01269…/307.00804… en Elimination of malfunctions General remarks on eliminating malfunctions: • Switch off the machine (exceptions: see *) • Eliminate malfunction • Switch on the unit • Notify Service if messages appear repeatedly. • Have servicing work carried out only by author- ized BEGO workshops! Service hotlin…

• 18, 44 85817 BA-en/12 306.01269…/307.00804… English ⋅ Miditherm MP en Settings Date and time 1. When switching on, keep button depressed: display shows «P1» (after approx. 3 seconds) and an acoustic signal sounds. 2. Set weekday with buttons: 1 = Monday, 2 = Tuesday, … , 7 = Sunday. 3. Press button to call up «P2» and set time (hours) with buttons. 4. Press butt…

• 12, Bego Miditherm 200 MP 38 85817 BA-en/12 306.01269…/307.00804… English ⋅ Miditherm MP en Creating a new program 1. Switch on the unit. The current temperature of the furnace is displayed after approx. 3 seconds. 2. Select program: • Press as often until LED # lights up. • Press until desired program number appears. 3. Call up programming mode: Keep button depressed until LED «°C/min.&qu…

• 5, English ⋅ Miditherm MP 31 85817 BA-en/12 306.01269…/307.00804… en Safety Instructions Miditherm is designed exclusively for wax removal from and preheating of dental objects, such as duplicate models and casting moulds made of commercially available investment materials. Any other use is considered to be improper. We shall not be liable for any damag…

• 10, 36 85817 BA-en/12 306.01269…/307.00804… English ⋅ Miditherm MP en Basic principles Displays after unit is switched on 0…3 sec: parameter of the controller > 3 sec: current furnace temperature Furnace care 1. Prior to first use, start program #9 (→ page 41): The furnace heats up to 1050 °C and maintains this temperature for 60 minutes. This results…

• 14, 40 85817 BA-en/12 306.01269…/307.00804… English ⋅ Miditherm MP en Checking a program 1. Switch on the unit. The current temperature of the furnace is displayed after approx. 3 seconds. 2. Select program: • Press as often until LED # lights up. • Press until desired program number appears. 3. Check values: Press to check the values of • heating-…

• 2, 28 85817 BA-en/12 306.01269…/307.00804… English ⋅ Miditherm MP en Table of contents General Information ………………………………………29 Safety Instructions…………………………………………31 Unit description …………………………………………….33 Scope of delivery, wearing parts and extras ……..34 Technical D…

• 13, Bego Miditherm 200 MP English ⋅ Miditherm MP 39 85817 BA-en/12 306.01269…/307.00804… en Creating a new program for shock heat investment materials 1.-3. → page 38. 4 Call up and set the parameters at holding level 1: • heating-up speed: 0°C/min. (= max.) • temperature of the holding level: see invest- ment material • duration of the holding level: see investment material Set the parameters of hol…

• 7, English ⋅ Miditherm MP 33 85817 BA-en/12 306.01269…/307.00804… en Unit description Miditherm MP Miditherm laboratory ovens serve for waxing and preheating of casting flasks and duplicate models. They provide users with the facility for using both shockheating and conventional embedding materials. The required finishing time, even for longer peri…

• 26, Bego Miditherm 200 MP 52 85817 BA-en/12 306.01269…/307.00804… English ⋅ Miditherm MP en Disposal Instructions for disposing of the device (Applicable only within the European Union) The adjacent symbol on the ID plate of the BEGO device indicates that the device, in accordance with the European directive on waste electrical and electronic equipment, may not be disposed of as normal domestic waste.…

Brand:
Bego

Category:
Laboratory Equipment

Type:
Translation of the original instructions

Model:
Bego Miditherm 100 MP
, Bego Miditherm 200 MP

Pages: 26

Download Bego Miditherm 100 MP Translation of the original instructions

Related Products for Bego Miditherm 200 MP

Related Manuals for Bego Miditherm 200 MP

Bego Miditherm 200 MP: Frequently viewed Manuals