Ошибка 092 315 xerox 5330

Вернуться в Принтеры, МФУ, копиры формата A3

Кто сейчас на форуме

Сейчас этот форум просматривают: нет зарегистрированных пользователей и гости: 17

BSD-ON:

BSD 9.3 — Development and Toner Dispense Control

The frequency at which the ATC Average Fail or the ATC Amplitude Fail has been occurring

has exceeded the threshold value.

NOTE: •

Although this Fault can be cleared by turning the power OFF and ON and it will be possi-

ble to output a few sheets of printouts, when this Fault has occurred a certain number of

times, it will no longer be clearable by turning the power OFF and ON. To clear it, clear the

value of NVM location [752-022] (ATC Average Fail) or NVM location [752-023] (ATC

Amplitude Fail) to «0»

(NVM

Read/Write). If the machine is not repaired back to normal

status, this Fault will occur again during the operation.

•

When turning the power OFF, turn OFF the power switch first and then the main power

switch.

Procedure

Check the following:

•

The connection between the MCU PWB

J615

for open circuit, short circuit, and poor contact

•

The Toner Dispense Motor for revolution failure:

•

The Toner Cartridge for internal toner blockage

If no problems are found, replace the following parts in sequence:

•

Drum Cartridge

(PL

8.1)

•

MCU PWB

(PL

18.2)

Initial Issue

WorkCentre 5335 Family Service Documentation

P/J413

and the Xero/Developer Cartridge

Component Control

[093-002]

(PL

8.2)

BUS Updated 12/2011

092-323 Dispense Fail RAP

BSD-ON:

BSD 9.3 — Development and Toner Dispense Control

Toner Cartridge becomes Empty despite less use of Toner amount.

NOTE: When turning the power OFF, turn OFF the power switch first and then the main power

switch.

Procedure

Check the following:

•

The connection between the MCU PWB

J615

for open circuit, short circuit, and poor contact

•

The Toner Dispense Motor for revolution failure:

•

The Toner Cartridge for internal toner blockage

If no problems are found, replace the following parts in sequence:

•

Drum Cartridge

(PL

8.1)

•

MCU PWB

(PL

18.2)

P/

07/2011

2-831

P/J413

and the Xero/Developer Cartridge

Component Control

[093-002]

(PL

8.2)

Status Indicator RAPs

092-315, 092-323

P/

1. 11-15-2017

   #1

   

   
   Senior Tech
   

   100+ Posts

   

   

   

   

   

   ---

   Rep Power

   30

   Advice Needed: Workcentre 7120 / System Error 092-315 on main display
   

   I am getting a system error 092-315 on the main display on startup. Which indicates a ATC Fail (K) Black.

   The error codes list states the following 092-315, 092-660, 092-668.

   Upon inspection of the drum unit I found the (K) Black toner exit hole packed to the brim with toner
   and piling up on top of the back of the drum. I looked at the other drum units (M,C,Y) and found no excess toner.

   After vacuuming and cleaning the (K) Black drum unit area as bets as possible, and resetting NVRAM
   752-368 (was at 1 reset to zero) 752-372 (was at 3 reset to zero).
   Turned machine off (Top Power Button first then inside cover button next) Machine upon starting up printed several blank pages, then there was a metal clink sound and the 092-315 system error redisplayed itself on main screen.

   I have determined that one of the following is at fault:
   Main Drive Assembly – 007K16710
   Dispense Motor -127K61161
   Developer Clutch – 121K46371
   Drum Drive Motor – 127K61161

   Since this a time and materials call, was just looking for opinions on which one of the above would
   be most likely to try first?

   All help is appreciated, and thanks in advance

   ---

2. 11-23-2017

   #2

   

   
   Senior Tech
   

   100+ Posts

   

   ---

   Rep Power

   0

   Re: Advice Needed: Workcentre 7120 / System Error 092-315 on main display
   

   Originally Posted by rockdude
   

   I am getting a system error 092-315 on the main display on startup. Which indicates a ATC Fail (K) Black.

   The error codes list states the following 092-315, 092-660, 092-668.

   Upon inspection of the drum unit I found the (K) Black toner exit hole packed to the brim with toner
   and piling up on top of the back of the drum. I looked at the other drum units (M,C,Y) and found no excess toner.

   After vacuuming and cleaning the (K) Black drum unit area as bets as possible, and resetting NVRAM
   752-368 (was at 1 reset to zero) 752-372 (was at 3 reset to zero).
   Turned machine off (Top Power Button first then inside cover button next) Machine upon starting up printed several blank pages, then there was a metal clink sound and the 092-315 system error redisplayed itself on main screen.

   I have determined that one of the following is at fault:
   Main Drive Assembly � 007K16710
   Dispense Motor -127K61161
   Developer Clutch � 121K46371
   Drum Drive Motor � 127K61161

   Since this a time and materials call, was just looking for opinions on which one of the above would
   be most likely to try first?

   All help is appreciated, and thanks in advance

   Hello Can you check the following.
   Check the following:

   • The connection between the MCU PWB P/J411 and the CRUM Reader (K) P/J123 for open circuit, short circuit, and poor contact
   • The connection terminals between the Drum Cartridge (K) CRUM PWB and the CRUM Reader (K) for damage and foreign substances
   • The Toner Dispense Motor (C,K) for revolution failure: Component Control [093-004] ( PL 5.1)
   • The Drum/IBT Drive Motor for revolution failure: Component Control [042-001] ( PL 3.2)
   • The Main Drive Motor for revolution failure: Component Control [042-006] ( PL 3.3)
   • The Dev K Clutch for failure: Component Control [042-010] ( PL 3.3)
   • The path from Toner Cartridge (K) to Developer (K) for toner blockage
   • The Developer (K) for internal toner blockage
   • The Toner Cartridge (K) for internal toner blockage

   If no problems are found, replace the following parts in sequence:

   • Drum Cartridge (K) ( PL 8.1)
   • MCU PWB ( PL 18.1)

   ---

3. 11-23-2017

   #3

   

   
   Senior Tech
   

   100+ Posts

   

   

   

   

   

   ---

   Rep Power

   30

   Re: Advice Needed: Workcentre 7120 / System Error 092-315 on main display
   

   Hi

   Thanks for the reply, but I already fixed it.

   Turned out replacing the Main Drive assembly was the answer.
   (and a through vacummingand cleaning)

   Gears were caked with toner, and clutch was sticking due to toner contamination.
   (Sorry I gave wrong part number for Main Drive. It was actually #007K16690)

   Thanks again for your input.

   ---