Ошибка 10 100 xerox b1022

– Compatible Printer model: Xerox B1022 MFP
– Xerox B1022 MFP Error Codes with quick guides:

• Code: 01-100
• Description: Side Door Open RAP
  The machine has detected that the side cover assembly is open.
• Troubleshooting Guides: • Ensure the side cover assembly is closed.
  Refer to Wiring Diagram 1 for B1022 Machines or Wiring Diagram 2 for B1025 Machines. Perform the steps that follow:
  1. Power off the device, then power on the device, GP 4.
  2. Enter dC330, code 01-100 side cover interlock, PL 1.10. Open and close the side cover assembly, PL 8.10 and check if the dC330 display changes.
  3. Check the interlock switch actuator flag on the side cover, PL 8.10 Item 2 is not missing or damaged.
  4. Check that the side cover assembly closes correctly.
  5. Refer to GP 10, then check the wiring between the side cover interlock switch and the Main PWB B1025 or Main PWB B1022. If necessary, install a new side cover interlock switch and harness assembly, PL 1.10 Item 14.

• Code: 01-150
• Description: Front Door Open RAP
  The machine has detected that the front cover is open.
• Troubleshooting Guides: • Ensure the front cover is closed.
  Refer to Wiring Diagram 1 for B1022 Machines or Wiring Diagram 2 for B1025 Machines. Perform the steps that follow:
  1. Power off the device, then power on the device, GP 4.
  2. Enter dC330, code 01-100 front cover interlock, PL 1.10. Open and close the front cover assembly, PL 28.10 Item 2 and check if the dC330 display changes.
  3. Check that the switch actuator flag on the front cover assembly, PL 28.10 Item 2 is not missing or damaged.
  4. Check that the front cover assembly closes correctly.
  5. Refer to GP 10, then check the wiring between the front cover switch and the Main PWB B1025 or Main PWB B1022. If necessary, install a new front cover switch and harness assembly, PL 1.10 Item 5.

• Code: 01-200
• Description: Tray 2 Side Cover Open RAP
  The machine has detected that the tray 2 side cover is open.
• Troubleshooting Guides: • Ensure the side cover is closed.
  • Check for obstructions behind the side cover.
  Refer to Wiring Diagram 1 for B1022 Machines or Wiring Diagram 2 for B1025 Machines. Perform the steps that follow:
  1. Power off the device, then power on the device, GP 4.
  2. Enter dC330, code 08-210 T2 door open sensor, PL 7.20 Item 14. Open and close the side cover PL 7.20 Item 5 and check if the dC330 display changes.
  3. Check that the sensor actuator on the side cover is not missing or damaged.
  4. Check that the side cover closes correctly.
  5. Refer to GP 10, then check the wiring between the T2 door open sensor and CN7 on the Tray 2 PWB.
  Install new components as necessary:
  1. T2 Door open sensor, PL 7.20 Item 14.
  2. Tray 2 PWB, PL 7.20 Item 9.

• Code: 02-100, 02-200
• Description: USB Faults RAP
  02-100 Invalid/Unknown USB device.
  02-200 Check USB memory.
• Troubleshooting Guides: Refer to Wiring Diagram 1 for B1022 Machines or Wiring Diagram 2 for B1025 Machines. Perform the steps that follow:
  1. Power off the device, then power on the device, GP 4.
  2. Ensure that the customer is using a valid USB device with sufficient free file space.
  3. Refer to GP 10, then check the wiring between the USB Host and the Main PWB B1022 or Main PWB B1025.
  Install new components as necessary:
  1. Front USB host cable, PL 1.10 Item 8.
  2. Main PWB, PL 1.10 Item 3.

• Code: 03-120
• Description: Tray 2 Interface Error RAP
  The machine has detected tray 2, but a communications error has occurred.
• Troubleshooting Guides: Refer to Wiring Diagram 1 for B1022 Machines or Wiring Diagram 2 for B1025 Machines. Perform the steps that follow:
  1. Power off the device, then power on the device, GP 4.
  2. Refer to GP 10, then check the wiring between the Main PWB B1022 or Main PWB B1025 and CN3 on the Tray 2 PWB.
  Install new components as necessary:
  1. Tray 2 PWB, PL 7.20 Item 9.
  2. Main PWB, PL 1.10 Item 3.

• Code: 03-410, 03-420, 03-450
• Description: Paper Information Mismatch RAP
  03-410 The machine has detected a tray 1 paper type or size mismatch.
  03-420 The machine has detected a tray 2 paper type or size mismatch.
  03-450 The machine has detected a bypass tray paper type or size mismatch.
• Troubleshooting Guides: 1. Power off the device, then power on the device, GP 4.
  2. From the UI or CWIS check that the appropriate tray paper size and type settings are correct.
  3. On the machine check that the appropriate tray media and guide settings match.
  4. 03-410 Only. Check the operation of the front and rear paper guides, PL 7.15. Install a new components as necessary: • Front guide, PL 7.15 Item 2. • Rear guide. PL 7.15 Item 4. • Left guide. PL 7.15 Item 13. • Pinion gear. PL 7.15 Item 11.
  5. 03-420 Only. Refer to Wiring Diagram 1 for B1022 Machines or Wiring Diagram 2 for B1025 Machines. Refer to GP 10, then check the wiring between the Main PWB B1022 or Main PWB B1025 and CN3 on the Tray 2 PWB. Check the operation of the front and rear paper guides, PL 7.25. Install a new components as necessary: • Front guide, PL 7.25 Item 2. • Rear guide. PL 7.25 Item 4. • Left guide. PL 7.25 Item 13. • Pinion gear. PL 7.25 Item 11.
  6. 03-450 Only. Check the operation of the front and rear gear racks and the pinion gear, PL 8.15. Install a new components as necessary: • Pinion gear. PL 8.15 Item 4 . • Bypass tray assembly, PL 8.10 Item 1.

• Code: 03-650
• Description: Ambient Temperature Sensor Fault RAP
  The machine has detected a fault with the ambient temperature sensor.
• Troubleshooting Guides: Refer to Wiring Diagram 1 for B1022 Machines or Wiring Diagram 2 for B1025 Machines. Perform the steps that follow:
  1. Power off the device, then power on the device, GP 4. 2. Refer to GP 10, then check the wiring between the temperature sensor, PL 7.40 Item 14 and the Main PWB B1022 or Main PWB B1025. 3. Install a new temperature sensor, PL 7.40 Item 14.

• Code: 03-800
• Description: SD Card Failure RAP
  The machine has detected a fault with the SD card.
• Troubleshooting Guides: Perform the steps that follow:
  1. Power off the device, then power on the device, GP 4. Install new components as necessary: 1. SD card, PL 1.10 Item 13.
  2. Main PWB, PL 1.10 Item 3.

• Code: 03-900, 03-901
• Description: UI Fault RAP
  03-900 A user interface to main PWB communications error has been detected.
  03-901 The machine has detected a user interface failure.
• Troubleshooting Guides: Refer to Wiring Diagram 1 for B1022 Machines or Wiring Diagram 2 for B1025 Machines. Perform the steps that follow:
  1. Power off the device, then power on the device, GP 4.
  2. Refer to GP 10, then check the wiring between the Main PWB B1022 or Main PWB B1025, PL 1.10 Item 3 and P/J2 on the UI PWB B1022, PL 2.10 Item 7 or CN4 on the UI PWB B1025, PL 2.15 Item 8.
  3. B1025 machines only, enter diagnostics GP 1, then perform dC305 user interface tests.
  4. B1022 machines only, enter diagnostics GP 1 then perform the System > Switch Test.
  Install a new components as necessary:
  1. UI PWB B1022, PL 2.10 Item 7.
  2. UI PWB B1025, PL 2.15 Item 8.
  3. Main PWB, PL 1.10 Item 3.

• Code: 04-500
• Description: Main Motor Locked RAP
  04-500 The machine has detected that the main BLDC motor does not run.
• Troubleshooting Guides: • Ensure the side cover assembly PL 8.10 Item 5 is closed.
  Refer to Wiring Diagram 1 for B1022 Machines or Wiring Diagram 2 for B1025 Machines. Perform
  the steps that follow:
  1. Power off, then power on the device, GP 4.
  2. Remove the toner cartridge, PL 9.10 Item 1, then remove the drum cartridge, PL 9.10 Item 2.
  3. Enter dC330, code 04-100. Check the main BLDC motor (MOT04-100) runs, PL 4.10 Item 11.
  4. Refer to GP 10, then check the wiring between the main BLDC motor, PL 4.10 Item 11 and the Main PWB B1022 or Main PWB B1025, PL 1.10 Item 3.
  Install new components as necessary:
  1. Main BLDC motor, PL 4.10 Item 11.
  2. Side cover interlock switch and harness assembly, PL 1.10 Item 14.
  3. Main PWB, PL 1.10 Item 3.

• Code: 04-600
• Description: Fuser Fan Locked RAP
  04-600 The machine has detected that the fuser fan does not run.
• Troubleshooting Guides: • Ensure the side cover assembly PL 8.10 Item 5 is closed.
  • Check for contamination or blockage in the fuser fan, PL 10.10 Item 3.
  Refer to Wiring Diagram 1 for B1022 Machines or Wiring Diagram 2 for B1025 Machines. Perform
  the steps that follow:
  1. Power off, then power on the device, GP 4.
  2. Enter dC330, code 10-500. Check the fuser fan motor (MOT10-500) runs.
  3. Refer to GP 10, then check the wiring between the fuser fan, PL 10.10 Item 3 and the
  Main PWB B1022 or Main PWB B1025, PL 1.10 Item 3.
  Install new components as necessary:
  1. Install a new fuser fan, PL 10.10 Item 3.
  2. Side cover interlock switch and harness assembly, PL 1.10 Item 14.
  3. Main PWB, PL 1.10 Item 3.

• Code: 04-910
• Description: SMPS Fan Locked RAP
  04-910 The machine has detected that the SMPS fan does not run.
• Troubleshooting Guides: • Ensure the front cover PL 28.10 Item 2 and side cover assembly PL 8.10 Item 5 are closed.
  • Check for contamination or blockage in the SMPS fan, PL 1.10 Item 7.
  Refer to Wiring Diagram 1 for B1022 Machines or Wiring Diagram 2 for B1025 Machines. Perform
  the steps that follow:
  1. Power off, then power on the device, GP 4.
  2. Enter dC330, code 09-500. Check the SMPS fan motor (MOT09-500) runs, PL 1.10 Item 7.
  3. Check the wiring between the SMPS fan, PL 1.10 Item 7 and CN4 on the HVPS PWB, PL 1.10 Item 2.
  Install a new components as necessary:
  1. SMPS Fan, PL 1.10 Item 7.
  2. HVPS PWB, PL 1.10 Item 2.

Solve Xerox B1022 MFP Error codes

• Code: 05-100
• Description: DADF Jam 1 RAP
  05-100 The lead edge or trail edge of the document failed to actuate or deactuate the scan sensor within the correct time.
• Troubleshooting Guides: Refer to Wiring Diagram B1025. Perform the steps that follow: 1. Open the DADF cover assembly, PL 5.15 Item 1. Remove any jammed paper.
  2. Check the document path for damage or obstructions.
  3. Check that the components that follow are clean and rotate freely. • Registration roller, PL 5.30 Item 8. • Registration roll idlers, part of the DADF cover assembly, PL 5.15 Item 1.
  4. Check that the registration actuator PL 5.25 Item 4, moves freely and is not damaged.
  5. Enter code 05-100. Check the document detect sensor (Q05-100). PL 5.35 Item 7.
  6. Remove the DADF rear cover, PL 5.15 Item 2. Enter code 05-200. Check that the DADF motor (MOT05-200) runs, PL 5.35 Item 2 and drives the exit roller, PL 5.30 Item 7.
  7. Close the DADF top cover assembly. While the DADF motor runs, stack the code 05-310 to energize the DADF registration clutch (CL05-310), PL 5.30 Item 10. Check that the registration roller, PL 5.30 Item 8 rotates.
  8. Refer to GP 10 and Wiring Diagram B1025, then check the wiring between the DADF motor MOT05-200, PL 5.35 Item 2, CN3 on the DADF PWB, PL 5.15 Item 3.
  9. Refer to GP 10 and Wiring Diagram B1025, then check the wiring between the DADF Regi clutch (CL05-310), PL 5.30 Item 10 and CN13 on the DADF PWB. If necessary, install a new DADF Regi clutch (CL05-310), PL 5.30 Item 10.
  10. If necessary, install new components: • DADF PWB, PL 5.15 Item 3. • DADF motor MOT05-200, PL 5.35 Item 2. • DADF feed sub PL 5.20 Item 5.

• Code: 05-300
• Description: DADF Jam 3 RAP
  05-300 The lead edge of the document failed to actuate the duplex sensor within the correct time in reverse mode.
• Troubleshooting Guides: Refer to Wiring Diagram B1025. Perform the steps that follow:
  1. Raise the DADF input tray assembly. PL 5.20 Item 4. Remove all jammed paper.
  2. Check the document path for damage or obstructions.
  3. Check that the components that follow are clean and rotate freely. • Exit roller, PL 5.30 Item 7. • Exit idle roller, PL 5.30 Item 18.
  4. Check that the exit actuator, PL 5.30 Item 17 moves freely and is not damaged.
  5. Enter dC330 code 05-170. Check the DADF exit sensor (Q05-170), PL 5.45 Item 2. If necessary, install a new DADF exit sensor (Q05-170), PL 5.45/2
  6. Remove the DADF rear cover, PL 5.15 Item 2. Enter code 05-200. Check that the DADF motor (MOT05-200) runs, PL 5.35 Item 2 and drives the exit roller, PL 5.30 Item 7.
  7. Enter dC330code 05-201. Check that the DADF motor (MOT05-200) runs, PL 5.35 Item 2 and drives the exit roller, PL 5.30 Item 7 in reverse.
  8. Refer to GP 10 and Wiring Diagram B1025, then check the wiring between the DADF motor MOT05-200, PL 5.35 Item 2, and CN3 on the DADF PWB, PL 5.15 Item 3.
  9. If necessary, install new components: • DADF PWB, PL 5.15 Item 3. • DADF motor MOT05-200, PL 5.35 Item 2. • DADF feed sub PL 5.20 Item 5.

• Code: 05-400
• Description: DADF Jam 4 RAP
  05-400 The lead edge or trail edge of the document failed to actuate or deactuate the scan sensor within the correct time in reverse mode.
• Troubleshooting Guides: Refer to Wiring Diagram B1025. Perform the steps that follow:
  1. Open the DADF cover assembly, PL 5.15 Item 1. Remove any jammed paper.
  2. Raise the DADF input tray assembly. PL 5.20 Item 4. Remove all jammed paper.
  3. Check the document path for damage or obstructions.
  4. Check that the following components are clean and rotate freely. • Feed roller, PL 5.30 Item 20. • SCF idle rollers, PL 5.45 Item 5. • Exit roller, PL 5.30 Item 7. • Exit idle roller, PL 5.30 Item 18.
  5. Check that the document present actuator, PL 5.25 Item 5 moves freely and is not damaged.
  6. Enter dC330 detect code 05-100. Check the document sensor (Q05-100). PL 5.35 Item 7.
  7. Remove the DADF rear cover, PL 5.15 Item 2. Enter code 05-200. Check that the DADF motor (MOT05-200) runs, PL 5.35 Item 2 and drives the components that follow: • Exit roller, PL 5.30 Item 7. • Exit idle roller, PL 5.30 Item 18.
  8. Refer to GP 10 and Wiring Diagram B1025, then check the wiring between the DADF motor MOT05-200, PL 5.35 Item 2, and CN3 on the DADF PWB, PL 5.15 Item 3.
  9. If necessary, install new components: • DADF PWB, PL 5.15 Item 3. • DADF motor MOT05-200, PL 5.35 Item 2. • DADF feed sub PL 5.20 Item 5.

• Code: 05-500
• Description: DADF Jam 5 RAP
  05-500 The machine has detected that the DADF or DADF top cover assembly are open during run.
• Troubleshooting Guides: Refer to Wiring Diagram B1025. Perform the steps that follow:
  1. Open the DADF cover assembly, PL 5.15 Item 1. Remove any jammed paper.
  2. Raise the DADF input tray assembly. PL 5.20 Item 4. Remove all jammed paper.
  3. Open the DADF. Check that the cover open sen 1 actuator, PL 14.10 Item 11, moves freely and is not damaged.
  4. Enter dC330 code 05-400. Check the cover open sen 1 (S05-400), PL 14.10 Item 11.
  5. Check the wiring between the cover open sen 1 and the main PWB. If necessary, install a new cover open sen 1, PL 14.10 Item 11.
  6. Open the DADF cover assembly, PL 5.25 Item 2. Check that the cover open sensor actuator is not damaged.
  7. Enter dC330 code 05-160. Check the cover open sensor (S05-160), PL 5.35 Item 7.
  8. Check the wiring between the DADF cover open sensor and CN6 on the DADF PWB. If necessary, install a new DADF cover open sensor, PL 5.35 Item 7.
  9. If necessary, install new components: • DADF PWB, PL 5.15 Item 3. • DADF feed sub PL 5.20 Item 5.

• Code: 05-600
• Description: DADF Jam 6 RAP
  05-600 The machine has detected that a DADF sensor is actuated when the machine is switched on.
• Troubleshooting Guides: Refer to Wiring Diagram B1025. Perform the steps that follow:
  1. Open the DADF cover assembly, PL 5.15 Item 1. Remove any jammed paper.
  2. Raise the DADF input tray assembly. PL 5.20 Item 4. Remove all jammed paper.
  3. Check the document path for damage or obstructions.
  4. Check that the actuators that follow move freely and are not damaged: • Registration actuator, PL 5.25 Item 4. • Document present actuator, PL 5.25 Item 5. • Exit actuator, PL 5.30 Item 17. • Rear rack gear guide, PL 5.40 Item 4. • Paper length actuator, PL 5.40 Item 8. • Scan actuator, PL 5.45 Item 6.
  5. Enter dC330. Check the sensors that follow. Install new components as necessary: • Document registration sensor (Q05-130), PL 5.35 Item 7. • Document detect sensor (Q05-100), PL 5.35 Item 7. • DADF exit sensor (Q05-170), PL 5.45 Item 2. • Width sensor 1 (Q05-110), PL 5.40 Item 9. • Width sensor 2 (Q05-111), PL 5.40 Item 9. • Width sensor 2 (Q05-112), PL 5.40 Item 9. • Length sensor 1 (Q05-120), PL 5.40 Item 9. • Length sensor 2 (Q05-121), PL 5.40 Item 9. • DADF scan start sensor (Q05-140), PL 5.45 Item 2.
  6. Check the wiring that follows: • Between the document registration sensor (Q05-130) and CN6 on the DADF PWB. • Between the document detect sensor (Q05-100) and CN6 on the DADF PWB. • Between the DADF exit sensor (Q05-170) and CN6 on the DADF PWB. • Between the width sensor 1 (Q05-110) and CN7 on the DADF PWB. • Between the width sensor 2 (Q05-111) and CN7 on the DADF PWB. • Between the width sensor 2 (Q05-112) and CN7 on the DADF PWB. • Between the length sensor 1 (Q05-120) and CN7 on the DADF PWB. • Between the length sensor 2 (Q05-121) and CN7 on the DADF PWB. • Between the DADF scan start sensor (Q05-140) and CN13 on the DADF PWB.
  7. If necessary, install new components: • DADF PWB, PL 5.15 Item 3. • DADF feed sub PL 5.20 Item 5.

• Code: 05-900
• Description: DADF Jam 0 RAP
  05-900 The lead edge of the document failed to actuate the registration sensor within the correct time.
• Troubleshooting Guides: Refer to Wiring Diagram B1025. Perform the steps that follow:
  1. Remove all jammed paper from the DADF input tray.
  2. Open the DADF cover assembly, PL 5.25 Item 2. Check the document path for damage or obstructions.
  3. Check the feed rollers, PL 5.30 Item 20. If necessary, clean the rollers.
  4. DADF friction pad assembly, PL 5.30 Item 2. If necessary, install a new DADF friction pad assembly, PL 5.30 Item 2.
  5. Check that the registration actuator PL 5.25 Item 4 moves freely and is not damaged.
  6. Enter dC330 code 05-130. Check the document registration sensor, Q05-130, PL 5.35 Item 7.
  7. Check the wiring between the document registration sensor and CN6 on the DADF PWB. If necessary, install a document registration sensor, Q05-130, PL 5.35 Item 7.
  8. Enter dC330 code 05-200. Check that the DADF motor MOT05-200, PL 5.35 Item 2 runs.
  9. While the DADF motor runs, stack the code 05-300 to energize the DADF pick up clutch (CL05-300). Check that the feed roll, PL 5.30 Item 20 rotates.
  10. Check the wiring between the pick up clutch and CN13 on the DADF PWB.
  11. Check the wiring between the DADF motor and CN3 on the DADF PWB.
  12. If necessary, install new components: • DADF PWB, PL 5.15 Item 3. • DADF motor MOT05-200, PL 5.35 Item 2. • DADF feed sub PL 5.20 Item 5.

• Code: 05-920
• Description: DADF Top Cover Open RAP
  05-920 The machine has detected that the DADF cover assembly is open.
• Troubleshooting Guides: Refer to Wiring Diagram B1025. Perform the steps that follow:
  1. Open the DADF cover assembly, PL 5.25 Item 2. Check that the DADF cover open sensor actuator on the DADF cover assembly, PL 5.15 Item 22 is not missing or damaged. If necessary, install a new DADF feed sub PL 5.20 Item 5.
  2. Enter dC330 code 05-160. Check the DADF cover open sensor (Q05-160), PL 5.35 Item 7.
  3. Check the wiring between the DADF cover open sensor and CN6 on the DADF PWB. If necessary, install a new DADF cover open sensor (Q05-160), PL 5.35 Item 7.
  4. If necessary, install new components: • DADF PWB, PL 5.15 Item 3. • DADF feed sub PL 5.20 Item 5.

• Code: 06-100, 06-200
• Description: LSU Error RAP
  06-100 The machine has detected that the LSU did not reach a ready state within the correct time.
  06-200 LSU Hsync error. The machine did not detect the laser beam within the correct time.
• Troubleshooting Guides: Refer to Wiring Diagram 1 for B1022 Machines or Wiring Diagram 2 for B1025 Machines. Perform the steps that follow:
  1. Power off, then power on the device, GP 4.
  2. Enter dC330 codes 06-100 and 06-110. Check that the LSU motor runs, PL 1.10 Item 4.
  3. Refer to GP 10, then check the flat cable between the LSU and the Main PWB B1022 or Main PWB B1025.
  4. If necessary, install a new LSU, PL 1.10 Item 4.

• Code: 07-110
• Description: Tray 1 Empty RAP
  07-110 The machine has detected that tray 1 is empty.
• Troubleshooting Guides: Refer to Wiring Diagram 1 for B1022 Machines or Wiring Diagram 2 for B1025 Machines. Perform the steps that follow:
  1. Power off the device, then power on the device, GP 4.
  2. Remove tray 1, PL 7.15 Item 1.
  3. Enter dC330, code 07-110. Check the tray 1 paper empty sensor (Q07-110), PL 7.10 Item 6.
  4. Refer to GP 10, then check the wiring between the tray 1 paper empty sensor and the Main PWB B1022 or Main PWB B1025, PL 1.10 Item 3.
  Install new components as necessary:
  1. Tray 1 paper empty sensor, PL 7.10 Item 6.
  2. Side cover interlock switch and harness assembly, PL 1.10 Item 14.
  3. Main PWB, PL 1.10 Item 3.

• Code: 07-130
• Description: Jam 0 From Tray 1 RAP
  07-130 The lead edge of the paper failed to actuate the registration sensor within the correct time after paper was fed from tray 1
• Troubleshooting Guides: NOTE: The side cover assembly interlock switch PL 1.10 Item 14 must be closed to supply +24V to the motors and clutches.
  Refer to Wiring Diagram 1 for B1022 Machines or Wiring Diagram 2 for B1025 Machines. Perform the steps that follow:
  1. Power off the device, then power on the device, GP 4.
  2. Remove tray 1, PL 7.15 Item 1. Remove any jammed paper.
  3. Check the paper path for damage or obstructions.
  4. Enter dC330, code 08-500. Check the registration sensor (Q08-500), PL 8.30 Item 9.
  5. Check that the registration sensor actuator moves freely and is not damaged.
  6. Enter dC330, code 04-100. Run the main BLDC motor, PL 4.10 Item 11.
  7. While the main BLDC motor runs stack the code 08-810 T1 pick-up clutch. Check that the tray 1 roller rotates, PL 7.15 Item 14.
  8. Refer to GP 10, then check the wiring between the registration sensor, main BLDC motor, pick-up clutch and the Main PWB B1022 or Main PWB B1025, PL 1.10 Item 3.
  Install new components as necessary:
  1. Registration sensor, PL 8.30 Item 9.
  2. Tray 1 roller, PL 7.15 Item 14.
  3. Main BLDC motor, PL 4.10 Item 11.
  4. Tray 1 pick-up clutch, PL 4.10 Item 8.
  5. Side cover interlock switch and harness assembly, PL 1.10 Item 14.
  6. Main PWB, PL 1.10 Item 3.

• Code: 07-210
• Description: Paper Empty at Tray 2 RAP
  07-210 The machine has detected that tray 2 is empty when the tray is full.
• Troubleshooting Guides: Refer to Wiring Diagram 1 for B1022 Machines or Wiring Diagram 2 for B1025 Machines. Perform the steps that follow:
  1. Power off the device, then power on the device, GP 4.
  2. Remove tray 2, PL 7.20 Item 1.
  3. Enter dC330, code 07-210. Check the tray 2 paper empty sensor (Q07-210), PL 7.20 Item 13.
  4. Refer to GP 10, then check the wiring between the tray 2 paper empty sensor (Q07-210) and the Tray 2 PWB, PL 7.20 Item 9.
  5. Refer to GP 10, then check the wiring between the tray 2 and the Main PWB B1022 or Main PWB B1025, PL 1.10 Item 3.
  Install new components as necessary:
  1. Tray 2 paper empty sensor, PL 7.20 Item 13.
  2. Main PWB, PL 1.10 Item 3.

• Code: 07-230
• Description: Jam 0 From Tray 2 RAP
  07-230 The lead edge of the paper failed to actuate the registration sensor within the correct time after paper was fed from tray 2.
• Troubleshooting Guides: NOTE: The side cover assembly interlock switch PL 1.10 Item 14 must be closed to supply +24V to the motors and clutches.
  Refer to Wiring Diagram 1 for B1022 Machines or Wiring Diagram 2 for B1025 Machines. Perform the steps that follow:
  1. Power off the device, then power on the device, GP 4.
  2. Remove tray 2, PL 7.20 Item 1. Remove any jammed paper.
  3. Open the side access cover, PL 7.20 Item 5. Remove all jammed paper.
  4. Check the paper path for damage or obstructions.
  5. Enter dC330, code 08-500. Check the registration sensor (Q08-500), PL 8.30 Item 9.
  6. Check that the registration sensor actuator moves freely and is not damaged.
  7. Refer to GP 10, then check the wiring between the registration sensor and the Main PWB B1022 or Main PWB B1025, PL 1.10 Item 3.
  8. Enter dC330, code 08-920. Run the tray 2 feed motor, PL 7.35 Item 1.
  9. While the tray 2 motor runs stack the code 08-820 tray 2 clutch, PL 7.35 Item 6. Check that the feed roll assembly rotates, PL 7.20 Item 2.
  10. Check the wiring between the tray 2 feed motor, PL 7.35 Item 1 and Tray 2 PWB, PL 7.20 Item 9.
  11. Check the wiring between the Tray 2 PWB, PL 7.20 Item 9 and the Main PWB B1022 or Main PWB B1025, PL 1.10 Item 3.
  Install new components as necessary:
  1. Registration sensor, PL 8.30 Item 9.
  2. Side cover interlock switch and harness assembly, PL 1.10 Item 14.
  3. Tray 2 feed motor, PL 7.35 Item 1.
  4. Tray 2 clutch, PL 7.35 Item 8.
  5. Feed roll assembly, PL 7.20 Item 2.
  6. Main PWB, PL 1.10 Item 3.

• Code: 07-500
• Description: Bypass Tray Faults RAP
  07-500 The machine has detected a failure to feed from the bypass tray.
  07-530 The registration sensor failed to actuate within the correct time after paper was fed from the bypass tray.
• Troubleshooting Guides: NOTE: The side cover assembly interlock switch PL 1.10 Item 14 must be closed to supply +24V to the motors and clutches.
  Refer to Wiring Diagram 1 for B1022 Machines or Wiring Diagram 2 for B1025 Machines. Perform the steps that follow:
  1. Power off the device, then power on the device, GP 4.
  2. Open the side cover assembly, PL 8.10 Item 5 . Check that the bypass guide area is clear and clean, PL 7.10 Item 1.
  3. Check the bypass retard pad, PL 7.10 Item 2.
  4. Check the operation of the bypass paper empty sensor actuator, PL 7.10 Item 8.
  5. Enter dC330 code 07-510. Check the bypass paper empty sensor (Q07-510), PL 7.10 Item 6.
  6. Check the wiring between the bypass paper empty sensor and the Main PWB B1022 or
  Main PWB B1025, PL 1.10 Item 3.
  7. Enter dC330, code 08-500. Check the registration sensor (Q08-500), PL 8.30 Item 9.
  8. Check that the registration sensor actuator moves freely and is not damaged.
  9. Refer to GP 10, then check the wiring between the registration sensor and the Main PWB B1022 or Main PWB B1025, PL 1.10 Item 3.
  10. Enter dC330, code 04-100. Run the main BLDC motor, PL 4.10 Item 11.
  11. While the main BLDC motor runs stack the code 08-800 bypass feed clutch, PL 7.10 Item
  12. Check that the bypass pick-up roll rotates, PL 7.10 Item 3.
  12. Refer to GP 10, then check the wiring between the Main BLDC motor, registration sensor, bypass paper empty sensor, bypass feed clutch and the Main PWB B1022 or Main PWB B1025, PL 1.10 Item 3.
  Install new components as necessary:
  1. Bypass paper empty sensor, PL 7.10 Item 6.
  2. Bypass retard pad, PL 7.10 Item 2.
  3. Registration sensor, PL 8.30 Item 9.
  4. Side cover interlock switch and harness assembly, PL 1.10 Item 14.
  5. Main BLDC motor, PL 4.10 Item 11.
  6. Bypass feed clutch, PL 7.10 Item 12.
  7. Feed roll assembly, PL 7.10 Item 3.
  8. Main PWB, PL 1.10 Item 3.

• Code: 07-600
• Description: All Trays Empty RAP
  07-600 The machine has detected that all paper trays are empty.
• Troubleshooting Guides: Go to the relevant procedure:
  • 07-110 Paper Empty at Tray 1 RAP.
  • 07-210 Paper Empty at Tray 2 RAP.
  • 07-500 Paper Empty at Bypass Tray RAP.

• Code: 08-100
• Description: Jam 1 RAP
  08-100 The machine has detected a paper jam in the paperpath.
• Troubleshooting Guides: • Check that the paper tray guides are set correctly.
  • Check the media is of the correct type, GP 5.
  • Ensure the size, orientation and type of media in the tray matches the media displayed in the UI menus.
  • Check the fault history, then clear any current faults, GP 2.
  NOTE: The side cover assembly interlock switch PL 1.10 Item 14 must be closed to supply +24V to the motors and clutches.
  Refer to Wiring Diagram 1 for B1022 Machines or Wiring Diagram 2 for B1025 Machines. Perform the steps that follow:
  1. Power off the device, then power on the device, GP 4.
  2. Open the side cover assembly PL 8.10 Item 5. Remove any jammed paper.
  3. Check the paper path for damage or obstructions.
  4. Remove the paper trays, then remove any jammed paper.
  5. Enter dC330, code 08-500. Check the registration sensor (Q08-500), PL 8.30 Item 9.
  6. Check that the registration sensor actuator moves freely and is not damaged.
  7. Refer to GP 10, then check the wiring between the registration sensor and the Main PWB B1022 or Main PWB B1025, PL 1.10 Item 3.
  8. Refer to GP 10, then check the registration feed roll, PL 8.30 Item 3 and registration idler roller, PL 8.30 Item 5. If necessary clean the rollers with a water dampened lint free cloth.
  9. Enter dC330, code 04-100. Run the main BLDC motor, PL 4.10 Item 11.
  10. While the main BLDC motor runs stack the code 08-850 registration clutch, PL 8.30 Item 4. Check that the registration feed roll rotates, PL 8.30 Item 3.
  11. Refer to GP 10, then check the wiring between the main BLDC motor, registration clutch and the Main PWB B1022 or Main PWB B1025, PL 1.10 Item 3.
  12. Enter dC330, code 10-400. Run the fuser motor, PL 10.10 Item 5, then check the fuser rollers rotates.
  13. Refer to GP 10, then check the wiring between the fuser motor and the Main PWB B1022 or Main PWB B1025, PL 1.10 Item 3.
  14. Enter dC330, code 08-600. Check the exit sensor (Q08-600), PL 10.10 Item 6.
  15. Refer to GP 10, then check the exit sensor actuator, PL 10.15 Item 1.
  16. Enter dC330, code 04-200. Run the exit motor, PL 10.10 Item 4, then check the exit rollers
  rotates, PL 10.20 Item 5.
  17. Refer to GP 10, then check the wiring between the exit motor and the Main PWB B1022 or Main PWB B1025, PL 1.10 Item 3.
  Install new components as necessary:
  1. Registration sensor, PL 8.30 Item 9.
  2. Registration feed roll, PL 8.30 Item 3.
  3. Main BLDC motor, PL 4.10 Item 11.
  4. Registration clutch, PL 8.30 Item 4.
  5. Side cover interlock switch and harness assembly, PL 1.10 Item 14.
  6. Fuser motor, PL 10.10 Item 5.
  7. Fuser assembly, PL 10.10 Item 2.
  8. Exit sensor, PL 10.10 Item 6.
  9. Exit motor, PL 10.10 Item 4.
  10. Exit assembly, PL 10.20 Item 1.
  11. Main PWB, PL 1.10 Item 3.

• Code: 08-500
• Description: Jam 2 RAP
  08-500 The machine has detected a paper jam in the fuser area.
• Troubleshooting Guides: NOTE: The side cover assembly interlock switch PL 1.10 Item 14 must be closed to supply +24V to the motors and clutches.
  Refer to Wiring Diagram 1 for B1022 Machines or Wiring Diagram 2 for B1025 Machines. Perform the steps that follow:
  1. Power off the device, then power on the device, GP 4.
  2. Open the side cover assembly PL 8.10 Item 5. Remove any jammed paper.
  3. Enter dC330, code 10-400. Run the fuser motor, PL 10.10 Item 5, then check the fuser rollers rotates.
  4. Refer to GP 10, then check the wiring between the fuser motor and the Main PWB B1022 or Main PWB B1025, PL 1.10 Item 3.
  5. Enter dC330, code 08-600. Check the exit sensor (Q08-600), PL 10.10 Item 6.
  6. Enter dC330, code 04-200. Run the exit motor, PL 10.10 Item 4, then check the exit rollers
  rotates, PL 10.20 Item 5.
  7. Refer to GP 10, then check the wiring between the exit motor and the Main PWB B1022 or Main PWB B1025, PL 1.10 Item 3.
  Install new components as necessary:
  1. Fuser motor, PL 10.10 Item 5.
  2. Fuser assembly, PL 10.10 Item 2.
  3. Exit sensor, PL 10.10 Item 6.
  4. Exit motor, PL 10.10 Item 4.
  5. Exit assembly, PL 10.20 Item 1.
  6. Main PWB, PL 1.10 Item 3.

• Code: 08-600
• Description: Duplex Jam 0 RAP
  08-600 The machine has detected a Jam in the duplex area
• Troubleshooting Guides: NOTE: The side cover assembly interlock switch PL 1.10 Item 14 must be closed to supply +24V to the motors and clutches.
  Refer to Wiring Diagram 1 for B1022 Machines or Wiring Diagram 2 for B1025 Machines. Perform the steps that follow:
  1. Power off the device, then power on the device, GP 4.
  2. Open the side cover assembly PL 8.10 Item 5. Remove any jammed paper.
  3. Enter dC330, code 04-220. Run the exit motor in reverse, PL 10.10 Item 4, then check the exit rollers rotates, PL 10.20 Item 5.
  4. Refer to GP 10, then check the wiring between the exit motor and the Main PWB B1022 or Main PWB B1025, PL 1.10 Item 3.
  5. Enter dC330, code 10-400. Run the fuser motor, PL 10.10 Item 5, then check the fuser rollers rotates.
  6. Refer to GP 10, then check the wiring between the fuser motor and the Main PWB B1022
  or Main PWB B1025, PL 1.10 Item 3.
  7. Refer to GP 10, then check the duplex drive gear, PL 4.10 Item 3, duplex drive in gear PL 8.20 Item 3 and duplex drive out gear PL 8.20 Item 2.
  8. Refer to GP 10, then check the duplex drive roller, PL 8.20 Item 6 and duplex feed roll, PL 8.20 Item 1.
  Install new components as necessary:
  1. Fuser motor, PL 10.10 Item 5.
  2. Fuser assembly, PL 10.10 Item 2.
  3. Exit sensor, PL 10.10 Item 6.
  4. Exit motor, PL 10.10 Item 4.
  5. Exit assembly, PL 10.20 Item 1.
  6. Duplex feed roller, PL 8.20 Item 1.
  7. Duplex drive roller, PL 8.20 Item 6
  8. Main PWB, PL 1.10 Item 3.

• Code: 09-100
• Description: Toner Low RAP
  09-100 The device has detected that the toner cartridge is almost empty. The toner material may be either low or unevenly distributed within the toner cartridge.
• Troubleshooting Guides: Perform the steps that follow:
  1. Remove the toner cartridge, REP 9.1.
  2. Gently shake the toner cartridge horizontally to distribute the toner evenly inside the cartridge.
  3. Reinstall the toner cartridge, REP 9.1.
  4. Ensure that a replacement toner cartridge, PL 9.10 Item 1 is in stock.

• Code: 09-200
• Description: Toner Empty RAP
  09-200 The device has detected that the toner cartridge is empty.
• Troubleshooting Guides: Refer to Wiring Diagram 1 for B1022 Machines or Wiring Diagram 2 for B1025 Machines. Perform the steps that follow:
  1. Ensure that the toner cartridge is not empty. If necessary, install a new toner cartridge, PL 9.10 Item 1.
  2. Enter dC330 code 09-600 and 09-700. Check that the toner dispense motor (MOT09-600, PL 4.10 Item 12) runs and deactuates the toner sensor (Q09-700).
  3. Remove the toner cartridge, PL 9.10 Item 1 and drum cartridge, PL 9.10 Item 2. Enter dC330 code 09-600. Ensure that the toner dispense motor runs (MOT09-600) and drives the toner cartridge supply coupling/gear, PL 4.10 Item 4.
  4. Check the wiring between the toner dispense motor and the Main PWB B1022 or Main PWB B1025, PL 1.10 Item 3.
  5. Check the wiring between the toner cartridge connector and the Main PWB B1022 or Main PWB B1025, PL 1.10 Item 3.
  6. If necessary, install a new toner cartridge, PL 9.10 Item 1. Enter dC135 HFSI and reset the toner cartridge counter
  Install new components as necessary:
  1. Toner dispense motor, PL 4.10 Item 12.
  2. Toner cartridge, PL 9.10 Item 1.
  3. Main PWB, PL 1.10 Item 3.

• Code: 09-260
• Description: Toner Dispense Motor RAP
  09-260 The toner dispense motor failure.
• Troubleshooting Guides: Refer to Wiring Diagram 1 for B1022 Machines or Wiring Diagram 2 for B1025 Machines. Perform the steps that follow:
  1. Remove the toner cartridge, PL 9.10 Item 1 and drum cartridge, PL 9.10 Item 2. Enter dC330 code 09-600, then check that the toner dispense motor (MOT09-600) runs and drives the toner cartridge supply coupling/gear, PL 4.10 Item 12.
  2. Check the wiring between the toner dispense motor (MOT09-600) and the Main PWB B1022 or Main PWB B1025, PL 1.10 Item 3.
  3. Enter dC330 code 09-700, then check that the toner dispense motor senor (Q09-700) PL 4.10 Item 17.
  4. Check the wiring between the toner dispense motor sensor and the Main PWB B1022 or Main PWB B1025, PL 1.10 Item 3.
  Install new components as necessary:
  1. Toner dispense motor, PL 4.10 Item 12.
  2. Toner dispense motor sensor, PL 4.10 Item 17.
  3. Main PWB, PL 1.10 Item 3.

• Code: 09-300
• Description: Drum Warning RAP
  09-300 The drum cartridge is near end of life.
• Troubleshooting Guides: Refer to Wiring Diagram 1 for B1022 Machines or Wiring Diagram 2 for B1025 Machines. Perform the steps that follow:
  1. No immediate action is necessary. Ensure that a replacement drum cartridge, PL 9.10 Item 2 is in stock.

• Code: 09-400
• Description: Drum Cartridge RAP
  09-400 The drum cartridge has reached the end of life.
• Troubleshooting Guides: Perform the steps that follow:
  1. Install a new drum cartridge, REP 9.2.
  2. Enter dC135 HFSI then reset the drum cartridge counter.

• Code: 09-500
• Description: Toner Cartridge Not Installed RAP
  09-500 The toner cartridge is not installed or the Customer Replaceable Unit Monitor (CRUM) is not making contact
• Troubleshooting Guides: Refer to Wiring Diagram 1 for B1022 Machines or Wiring Diagram 2 for B1025 Machines. Perform the steps that follow:
  1. Power off, then power on the device, GP 4.
  2. Remove the toner cartridge, REP 9.1.
  3. Check the contacts on the toner CRUM connector.
  4. Reinstall the toner cartridge, REP 9.1.
  5. Refer to GP 10. Check the wiring between the toner CRUM connector and the Main PWB B1022 or Main PWB B1025, PL 1.10 Item 3.
  Install new components as necessary:
  1. Toner cartridge, PL 9.10 Item 1. Enter dC135 HFSI then reset the toner cartridge counter.
  2. Main PWB, PL 1.10 Item 3.

• Code: 09-600, 09-730
• Description: Drum Cartridge Error RAP
  09-600 The drum cartridge is not installed or the Customer Replaceable Unit Monitor (CRUM) is not making contact.
  09-730 The device has detected a drum cartridge error.
• Troubleshooting Guides: Refer to Wiring Diagram 1 for B1022 Machines or Wiring Diagram 2 for B1025 Machines. Perform the steps that follow:
  1. Power off, then power on the device, GP 4.
  2. Remove the drum cartridge, REP 9.2.
  3. Check the contacts on the drum CRUM connector.
  4. Reinstall the drum cartridge, REP 9.2.
  5. Refer to GP 10. Check the wiring between the drum cartridge connector PL 1.10 Item 16 and the Main PWB B1022 or Main PWB B1025, PL 1.10 Item 3.
  6. Install a new components as necessary:
  • Drum cartridge, PL 9.10 Item 2.
  • Front cover switch and harness assembly, PL 1.10 Item 5.
  7. Enter dC135 HFSI then reset the drum cartridge counter.

• Code: 09-700, 09-720
• Description: Toner Supply Error RAP
  09-700 The device has detected an insufficient supply of toner to the drum cartridge.
  09-720 The device has detected a toner supply error.
• Troubleshooting Guides: Refer to Wiring Diagram 1 for B1022 Machines or Wiring Diagram 2 for B1025 Machines. Perform the steps that follow:
  1. Power off, then power on the device, GP 4.
  2. Remove the drum cartridge, REP 9.2.
  3. Check that the tape seal on the toner cartridge has been removed.
  4. Perform the 09-260 Toner Dispense Motor RAP.
  5. Gently shake the toner cartridge horizontally to distribute the toner evenly inside the cartridge.
  6. Reinstall the drum and toner cartridges.
  7. Install a new components as necessary:
  • Toner cartridge, PL 9.10 Item 1.
  • Drum cartridge, PL 9.10 Item 2.
  8. Enter dC135 HFSI then reset the appropriate cartridge counter.

• Code: 09-710
• Description: Image Quality Adjustment RAP
  09-710 The device is performing image quality adjustments.
• Troubleshooting Guides: No service actions are required. Advise the customer to wait until the calibrations have completed.
  Printing is held while the adjustments are in progress, all other machine services (if
  installed) are unaffected.

• Code: 09-800, 09-810
• Description: Incompatible Toner Cartridge RAP
  09-800 The device has detected an incompatible toner cartridge.
  09-810 The device has detected a non Xerox toner cartridge.
• Troubleshooting Guides: Perform the steps that follow:
  1. Remove the toner cartridge, REP 9.1.
  2. Ensure that the toner cartridge is the correct toner cartridge for the device.
  3. Install a new toner cartridge, PL 9.10 Item 1
  4. Enter dC135 HFSI then reset the toner cartridge counter.

• Code: 09-900, 09-910
• Description: Incompatible Drum Cartridge RAP
  09-900 The machine has detected an incompatible drum cartridge.
  09-910 The machine has detected a non Xerox drum cartridge.
• Troubleshooting Guides: Perform the steps that follow:
  1. Remove the drum cartridge, REP 9.2.
  2. Ensure that the drum cartridge is the correct drum cartridge for the device.
  3. Install a new drum cartridge, PL 9.10 Item 2.
  4. Enter dC135 HFSI then reset the drum cartridge counter.

• Code: 09-950
• Description: Transfer Roller Warning RAP
  09-950 The transfer roller is near end of life.
• Troubleshooting Guides: Perform the steps that follow:
  1. No immediate action is necessary. Ensure that a replacement transfer roll assembly, PL 8.25 Item 5 is in stock.

• Code: 09-960
• Description: Transfer Roller End of Life RAP
  09-960 The transfer roller has reached the end of life.
• Troubleshooting Guides: Perform the steps that follow:
  1. Install a new transfer roll assembly, PL 8.25 Item 5.
  2. Enter dC135 HFSI then reset the transfer roller counter.

• Code: 09-970
• Description: Transfer Roller Error RAP
  09-970 The device has detected a transfer assembly error.
• Troubleshooting Guides: Refer to Wiring Diagram 1 for B1022 Machines or Wiring Diagram 2 for B1025 Machines. Perform the steps that follow:
  1. Remove, then reseat the transfer roller assembly, PL 8.25 Item 5.
  2. Check the transfer roller assembly for up and down movement.
  3. Check the high voltage contacts between the HVPS, PL 1.10 Item 2, high voltage connector,
  PL 1.10 Item 6 and the transfer roller assembly for continuity.
  4. Install a new components as necessary:
  • Transfer roll assembly, PL 8.25 Item 5.
  • High voltage connector, PL 1.10 Item 6.
  • HVPS, PL 1.10 Item 2.

• Code: 10-100, 10-200
• Description: Open Fuser Error/Low Heat Error RAP
  10-100 During normal operation, the temperature of the fuser has dropped below the operating level.
  10-200 The fuser has failed to reach the correct operating temperature.
• Troubleshooting Guides: • Enter dC330 code 10-500 Check the fuser fan runs, PL 10.10 Item 3. If necessary perform the 04-910 Fuser Fan Locked RAP.
  Refer to Wiring Diagram 1 for B1022 Machines or Wiring Diagram 2 for B1025 Machines. Perform the steps that follow:
  1. Power off the device, then power on the device, GP 4.
  2. Enter dC330 codes 10-200 (centre thermistor) and 10-210 (front thermistor) to verify the condition of the thermistors.
  3. Check that the thermistors, PL 10.15 Item 9 and PL 10.15 Item 18 are clean and in good contact with the fuser heat roller.
  4. Refer to GP 10, then check the wiring between the fuser assembly, PL 10.10 Item 2 and the SMPS, PL 1.10 Item 1.
  5. Switch on the device, then check the fuser input voltage CON1 on the SMPS.
  6. Refer to GP 10, then check the wiring between CON4 on the SMPS and the Main PWB B1022 or Main PWB B1025, PL 1.10 Item 3.
  7. If the fault persists install new components as necessary:
  • Fuser assembly, PL 10.10 Item 2
  • SMPS, PL 1.10 Item 1.
  • HVPS, PL 1.10 Item 2.

• Code: 10-300, 10-310
• Description: Fuser Over Temperature RAP
  10-300 The temperature of the fuser has risen over the operating level.
  10-310 The fuser temperature is under adjustment.
• Troubleshooting Guides: • Enter dC330 code 10-500 Check the fuser fan motor runs, PL 10.10 Item 3. If necessary perform the 04-600 04-910 Fuser Fan Locked RAP.
  Refer to Wiring Diagram 1 for B1022 Machines or Wiring Diagram 2 for B1025 Machines. Perform the steps that follow:
  1. Power off the device, GP 4. Wait until the fuser has cooled down, then power on the device GP 4.
  2. If the fault persists install a new fuser assembly, PL 10.10 Item 2.

– Get more error code list with quick guide to fix printer product, click here


– About get help with reseting Epson inkpad or others, click here

– Get more information about Epson XP 15000 troubleshooting, click here

Xerox printer reset software introduction:

Notes before resetting Xerox printer:

– Identify accurate version, serial and crum of Xerox printer.
– How to get Xerox printer model info: Click Here
– Before you continue with the reprogramming of the firmware, please make sure that the device is installed on your computer.
– It is very important that under no circumstances should you remove the chip from the cartridge while reprogramming the firmware. After you have succesfully reprogrammed the printer, remove the chip from the cartridge and store it somewhere safely (the chip – a key). In all cartridges which you are going to use in the printer, the chip has to be either removed or sealed. If you have accidently inserted a new cartridge without removing the chip, the device will be blocked. In order to unblock it, you can use the stored chip as a key which help you to unblock the printer.
– And make sure that any other devices (except mouse and keyboard), which are connected to your computer via USB or LPT ports are disconnected. It’s preferable that the computer is connected to the “UPS” (uninterruptible power source) device, because if during the reprogramming process the electricity source has any interruptions, then the reprogramming will be carried out with an error, which makes the device unable to work.
– This firmware will be installed directly to your printer. Before opening firmare link make sure that printer is turned on and connected to your computer and printer drivers are installed correctly.
Be aware that with the reprogramming of the firmware the manufacturer’s warranty goes lost!!

How To Run Firmware Fix Xerox printer

1. Connect the printer to the computer and turn it on.
2. Wait until the printer is ready for work.
3. Drag and drop *.hd to usbprns2.exe file.

4. The reprogramming process starts automatically.
5. Wait until the printer reprograms (10-20 minute) and restarts.
6. After that the reprogramming process is finished, restart the printer.
– Fix Xerox B205 Toner Empty Error, click here

Contact us to get support with Xerox B1022 MFP Error case

Telegram: https://t.me/hyperaktiv
Facebook: https://www.facebook.com/dngnm/
Or click here to get more ways.