Ошибка 7410 kyocera 3060

Модератор: vetal

Прилепить пост

Изменить размер шрифта ↓ВернутьИзменить размер шрифта ↑Всем привет. Данный аппарат выдает ошибку 7410. Я понимаю что эта ошибка говорит о плохом контакте на драм, но при включении принтера с открытой крышкой, аппарат выходит в готовность, далее закрываем крышку, и он печатает без проблем, без каких либо дефектов. Принтак продувал, чистил, ничего не помогло, Ставлю другой драм с другой проявкой, та же ошибка, поставил третий драм с другой проявкой выдал ошибку 0180, со старым драмом так же C7410

То, что другие люди говорят обо мне, никак не характеризует меня. Зато отлично характеризует их.

Аватар пользователя

Andreyak777

  

Избран тонером

  • Не в сети

Прилепить пост

Сообщение kvg » Чт июн 20, 2019 8:56 am

Изменить размер шрифта ↓ВернутьИзменить размер шрифта ↑А стандартное решение проблемы не помогает?

Выключите принтер. Откройте левую дверь и нажмите на барабан, пока он не защелкнется на месте. Снова включите принтер, аппарат войдет в готовность.

Аватар пользователя

kvg

  

Администратор сайта и форума

  • Не в сети
  • Сайт
  • Персональный альбом



Прилепить пост

Сообщение Andreyak777 » Чт июн 20, 2019 1:08 pm

То, что другие люди говорят обо мне, никак не характеризует меня. Зато отлично характеризует их.

Аватар пользователя

Andreyak777

  

Избран тонером

  • Не в сети

Прилепить пост

Сообщение Andreyak777 » Чт июн 20, 2019 1:12 pm

То, что другие люди говорят обо мне, никак не характеризует меня. Зато отлично характеризует их.

Аватар пользователя

Andreyak777

  

Избран тонером

  • Не в сети


Прилепить пост

Сообщение Andreyak777 » Чт июн 20, 2019 2:47 pm

То, что другие люди говорят обо мне, никак не характеризует меня. Зато отлично характеризует их.

Аватар пользователя

Andreyak777

  

Избран тонером

  • Не в сети

Прилепить пост

Сообщение pc-porta » Чт июн 20, 2019 3:24 pm

Изменить размер шрифта ↓ВернутьИзменить размер шрифта ↑

Andreyak777 писал(а):Если была бы проблема в контактах, грязь там и все такое, почему он тогда нормально печатает когда загружается с открытой крышкой??

люфтит у Вас драм (шатает его) при закрывании крышки …

Драм совместимка или оригинал ?
Контакты чють подвытянуть в драме или принтаке … для лучшего и надёжного контакта :))

Аватар пользователя

pc-porta

  

Тонерный автобот

  • Не в сети
  • Персональный альбом

Прилепить пост

Сообщение dviz » Чт июн 20, 2019 7:14 pm

Изменить размер шрифта ↓ВернутьИзменить размер шрифта ↑

Andreyak777 писал(а):DK3130 изначально стоял, с ним все работало

Оно конечно, хорошо, но это ж не родной — может глюк какой — там в нём плата сопряжения маленькая с микрухой(кто-то на форуме уже писал, что они иногда дохнут) и датчик регистрации лишний (можно попробовать его отключить).
Плюс ещё по 0180 — проверить в U004 не сбойнули ли серийные номера.

Аватар пользователя

dviz

  

Эксперт по тонеру

  • Не в сети
  • Персональный альбом


Прилепить пост

Сообщение dviz » Пт июн 21, 2019 10:54 am

Изменить размер шрифта ↓ВернутьИзменить размер шрифта ↑Да, в 3130 стоит датчик регистрации, в 3100 — нет, и для m3040 — не нужен.

Надо бы для начала узнать с каких аппаратов и какие модели драмов ставились..


За это сообщение автора dviz поблагодарил:
admdep33

Аватар пользователя

dviz

  

Эксперт по тонеру

  • Не в сети
  • Персональный альбом

  Вопрос решен

Прилепить пост

Сообщение dviz » Пт июн 21, 2019 2:57 pm

Изменить размер шрифта ↓ВернутьИзменить размер шрифта ↑Только что была возможность поэксперимениировать.

Вытащил из включенного m3040dn dk-3100, установил dk-3130 — работает. Выключил-включил — ошибка c7410. Вернул dk-3100 обратно — всё норм.

В fs-4100 вместо dk-3130 установил dk-3100 — ошибка замятия бумаги — ожидаемо — ведь в dk-3100 нет датчика регистрации и в аппарате нет..


За это сообщение автора dviz поблагодарил:
Andreyak777

Аватар пользователя

dviz

  

Эксперт по тонеру

  • Не в сети
  • Персональный альбом


Прилепить пост

Сообщение dviz » Пт июн 21, 2019 3:51 pm

Изменить размер шрифта ↓ВернутьИзменить размер шрифта ↑Проблема в данном случае не в самом наличии или отсутствии датчика, а в том что используется не родной драм..

В аппаратах со скоростью 40-45 стр/мин — fs 2100, m3040, p3045 и т.п. — два датчика регистрации в самом аппарате, поэтому датчик в драме не требуется. Во всех остальных — в самом аппарате один датчик и один в драме.

Тут поправлюсь — в fs2100, m3040, p3045 не два, а только один датчик регистрации — до валов регистрации, а в остальных аппаратах два: один — после валов регистрации, и один — в драме.

Последний раз редактировалось dviz Сб июн 22, 2019 3:42 pm, всего редактировалось 1 раз.


За это сообщение автора dviz поблагодарил:
admdep33

Аватар пользователя

dviz

  

Эксперт по тонеру

  • Не в сети
  • Персональный альбом


  • Kyocera FS-1120d индикатор «Нет бумаги»

    vs-dos в форуме Принтеры, МФУ, факсы, копиры формата A4

    11
    15145

    СТРОНЦИЙ
    Перейти к последнему сообщению
    Вт ноя 02, 2021 2:24 pm
  • [SCANNER ERROR] Lamp Error Kyocera FS-1016

    мастерчип в форуме Принтеры, МФУ, факсы, копиры формата A4

    3
    6646

    Усатый Полосатый
    Перейти к последнему сообщению
    Вс окт 28, 2018 11:08 pm
  • Kyocera 1035 «бледная» печать

    srMax в форуме Принтеры, МФУ, факсы, копиры формата A4

    2
    13951

    srMax
    Перейти к последнему сообщению
    Пт янв 23, 2015 2:49 pm
  • Taskalfa 180 ошибка «Е» и «Встряхните картр. с тонером»

    manik.76 в форуме Принтеры, МФУ, копиры формата A3

    3
    9661

    dviz
    Перейти к последнему сообщению
    Пн фев 20, 2017 1:35 pm
  • Kyocera Ecosys M2635dn «поворот» изображения

    Искатель в форуме Принтеры, МФУ, факсы, копиры формата A4

    10
    6107

    MatrixAgent
    Перейти к последнему сообщению
    Ср апр 08, 2020 5:18 am

Вернуться в Принтеры, МФУ, факсы, копиры формата A4

Кто сейчас на форуме

Сейчас этот форум просматривают: tw012326 и гости: 145

Правила форума
Картинки и фотографии (если они нужны в сообщении) надо загружать только как вложения к своему сообщению (через кнопку Добавить файлы). Тогда картинки будут автоматически отображаться в сообщении.

lamac0

Сообщения: 4
Стаж: 7 месяцев

KYOCERA P3145DN код ошибки 7410:0035148

Сообщение

lamac0 » 12 окт 2022, 08:49

Всем по привету, при включении данный аппарат говорит обратиться к сервисникам с кодом ошибки 7410:0035148, понимая, что дело где-то в драме зарыто полез копать гуглы, там сказали, что бывает крякает плата на драме, нашел донора, подкинул плату и результата нет, НО! если выдеруть питалово, открыть крышку переднюю, подать питалово, то он работает как ни в чем не бывало, до ребута

Аватара пользователя

dviz

Сообщения: 205
Стаж: 1 год 5 месяцев
Откуда: Ярославль
Благодарил (а): 15 раз
Поблагодарили: 25 раз

Репутация:

KYOCERA P3145DN код ошибки 7410:0035148

Сообщение

dviz » 15 окт 2022, 03:41

Если есть донор — то ставьте донора и проверяйте работоспособность. Только хорошо бы конечно быть уверенным, что донор действительно рабочий. Если с открытой крышкой включается, то вероятно он при инициализации не проверяет работоспособность всех компонентов драма, а с закрытой проверяет и что-то его не устраивает — проверьте всё что там подключено к этой платке — датчик тонера, движок подмеса, засветку фотика.

  • 4 Ответы
    494 Просмотры
    Последнее сообщение

    Аватара пользователя

    22 окт 2022, 21:22

  • 2 Ответы
    547 Просмотры
    Последнее сообщение

    Я поленился установить аватар

    03 мар 2023, 02:18

  • 1 Ответы
    156 Просмотры
    Последнее сообщение

    Я поленился установить аватар

    19 сен 2022, 07:48

  • 21 Ответы
    186 Просмотры
    Последнее сообщение

    Я поленился установить аватар

    30 май 2023, 23:34

  • 0 Ответы
    129 Просмотры
    Последнее сообщение

    Я поленился установить аватар

    13 дек 2022, 19:30

  • Code: 0100
  • Description: Backup memory device error
  • Remedy: Defective flash memory. Replace the main PWB and check for correct operation.
    Defective main PWB. Replace the main PWB and check for correct operation.
  • Code: 0120
  • Description: MAC address data error For data in which the MAC address is invalid.
  • Remedy: Defective flash memory. Replace the main PWB and check for correct operation.
    Defective main PWB. Replace the main PWB and check for correct operation.
  • Code: 0130
  • Description: Backup memory read/write error (main PWB)
  • Remedy: Defective flash memory. Replace the main PWB and check for correct operation.
    Defective main PWB. Replace the main PWB and check for correct operation.
  • Code: 0140
  • Description: Backup memory data error (main PWB)
  • Remedy: Defective flash memory. Replace the main PWB and check for correct operation.
    Defective main PWB. Replace the main PWB and check for correct operation.
  • Code: 0150
  • Description: Backup memory read/write error (engine PWB) Detecting engine PWB EEPROM communication error.
  • Remedy: Improper installation engine PWB EEPROM. Check the installation of the EEPROM and remedy if necessary.
    Defective engine PWB. Replace the engine PWB and check for correct operation.
    Device damage of EEPROM. Contact the Service Administrative Division.
  • Code: 0160
  • Description: Backup memory data error (engine PWB)
  • Remedy: Defective EEPROM. Replace the engine PWB and check for correct operation.
    Defective engine PWB. Replace the engine PWB and check for correct operation.
  • Code: 0170
  • Description: Billing counting error A checksum error is detected in the main and engine backup memories for the billing counters.
  • Remedy: Data damage of EEPROM. Contact the Service Administrative Division.
    Defective PWB. Replace the main PWB or the engine PWB and check for correct operation.
  • Code: 0190
  • Description: Backup memory device error (engine PWB)
  • Remedy: Defective engine PWB. Replace the engine PWB and check for correct operation.
  • Code: 0800
  • Description: Image processing error JAM010x is detected twice.
  • Remedy: Defective main PWB. Replace the main PWB and check for correct operations page 1-5-22).
  • Code: 0840
  • Description: Faults of RTC Unable to communicate with the RTC device normally. The RTC data is mismatched due to dead battery or shortcircuit with the metal part.
  • Remedy: Other RTC device failure due to dead battery or short-circuit with the metal part. Restart the main unit and set the correct time from the operation panel. Repair it if the battery comes off from the main PWB.
    Defective main PWB. Replace the main PWB and check for correct operation.
  • Code: 1010
  • Description: Lift motor error (60/55/50 ppm model only) After cassette 1 is inserted, lift sensor does not turn on within 10 s. This error is detected five times successively.
  • Remedy: Defective bottom plate elevation mechanism in the cassette. Check to see if the bottom plate can move smoothly and repair it if any problem is found.
    Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. Lift motor and engine PWB (YC13)
    Defective drive transmission system of the lift motor. Check if the gears rotate smoothly. If not, grease the bushes and gears. Check for broken gears and replace if any.
    Defective lift motor. Replace the lift motor.
    Defective engine PWB. Replace the engine PWB and check for correct operation.
  • Code: 1020
  • Description: PF lift motor 1 error (paper feeder) After cassette 2 is inserted, PF lift sensor 1 does not turn on. This error is detected four times successively.
  • Remedy: Defective bottom plate elevation mechanism in the cassette. Check to see if the bottom plate can move smoothly and repair it if any problem is found.
    Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. PF lift motor 1 and PF main PWB (YC7)
    Defective drive transmission system of the PF lift motor. Check if the gears rotate smoothly. If not, grease the bushes and gears. Check for broken gears and replace if any.
    Defective PF lift motor. Replace the PF lift motor 1.
    Defective PF main PWB. Replace the PF main PWB (Refer to the service manual for the paper feeder).
  • Code: 1030
  • Description: PF lift motor 2 error (paper feeder) After cassette 3 is inserted, PF lift sensor 2 does not turn on. This error is detected four times successively.
  • Remedy: Defective bottom plate elevation mechanism in the cassette. Check to see if the bottom plate can move smoothly and repair it if any problem is found.
    Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. PF lift motor 2 and PF main PWB (YC7)
    Defective drive transmission system of the PF lift motor. Check if the gears rotate smoothly. If not, grease the bushes and gears. Check for broken gears and replace if any.
    Defective PF lift motor. Replace the PF lift motor 2.
    Defective PF main PWB. Replace the PF main PWB (Refer to the service manual for the paper feeder).
  • Code: 1040
  • Description: PF lift motor 3 error (paper feeder) After cassette 4 is inserted, PF lift sensor 3 does not turn on. This error is detected four times successively.
  • Remedy: Defective bottom plate elevation mechanism in the cassette. Check to see if the bottom plate can move smoothly and repair it if any problem is found.
    Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. PF lift motor 3 and PF main PWB (YC7)
    Defective drive transmission system of the PF lift motor. Check if the gears rotate smoothly. If not, grease the bushes and gears. Check for broken gears and replace if any.
    Defective PF lift motor. Replace the PF lift motor 3.
    Defective PF main PWB. Replace the PF main PWB (Refer to the service manual for the paper feeder).
  • Code: 1050
  • Description: PF lift motor 4 error (paper feeder) After cassette 5 is inserted, PF lift sensor 4 does not turn on. This error is detected four times successively.
  • Remedy: Defective bottom plate elevation mechanism in the cassette. Check to see if the bottom plate can move smoothly and repair it if any problem is found.
    Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. PF lift motor 4 and PF main PWB (YC7)
    Defective drive transmission system of the PF lift motor. Check if the gears rotate smoothly. If not, grease the bushes and gears. Check for broken gears and replace if any.
    Defective PF lift motor. Replace the PF lift motor 4.
    Defective PF main PWB. Replace the PF main PWB (Refer to the service manual for the paper feeder).
  • Code: 1140
  • Description: BPF lift motor upward error (Bulk paper feeder) BPF lift maximum sensor does not turn on. The lock signal of the motor is detected continuously three times.
  • Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. BPF lift motor and BPF main PWB (YC4)
    Defective drive transmission system of the motor. Check if the gears rotate smoothly. If not, grease the bushes and gears. Check for broken gears and replace if any.
    Defective BPF lift motor. Replace the BPF lift motor.
    Defective BPF main PWB. Replace the BPF main PWB (Refer to the service manual for the paper feeder).
  • Code: 1150
  • Description: BPF lift motor downward error (Bulk paper feeder) BPF lift minimum sensor does not turn on. The lock signal of the motor is detected continuously three times. When detecting an overcurrent detection signal.
  • Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. BPF lift motor and BPF main PWB (YC4)
    Defective drive transmission system of the motor. Check if the gears rotate smoothly. If not, grease the bushes and gears. Check for broken gears and replace if any.
    Defective BPF lift motor. Replace the BPF lift motor.
    Defective BPF main PWB. Replace the BPF main PWB (Refer to the service manual for the paper feeder).
  • Code: 1800
  • Description: Paper feeder 1 communication error A communication error is detected 10 times in succession.
  • Remedy: Improper installation paper feeder. Follow installation instruction carefully again.
    Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. PF main PWB (YC3) and engine PWB (YC22)
    Defective engine PWB. Replace the engine PWB and check for correct operation.
    Defective PF main PWB. Replace the PF main PWB (Refer to the service manual for the paper feeder).
  • Code: 1810
  • Description: Paper feeder 2 communication error A communication error is detected 10 times in succession.
  • Remedy: Improper installation paper feeder. Follow installation instruction carefully again.
    Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. PF main PWB (YC3) and engine PWB (YC22)
    Defective PF main PWB. Replace the PF main PWB (Refer to the service manual for the paper feeder).
  • Code: 1820
  • Description: Paper feeder 3 communication error A communication error is detected 10 times in succession.
  • Remedy: Improper installation paper feeder. Follow installation instruction carefully again.
    Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. PF main PWB (YC3) and engine PWB (YC22)
    Defective PF main PWB. Replace the PF main PWB (Refer to the service manual for the paper feeder).
  • Code: 1830
  • Description: Paper feeder 4 communication error A communication error is detected 10 times in succession.
  • Remedy: Improper installation paper feeder. Follow installation instruction carefully again.
    Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. PF main PWB (YC3) and engine PWB (YC22)
    Defective PF main PWB. Replace the PF main PWB (Refer to the service manual for the paper feeder).
  • Code: 1900
  • Description: Paper feeder 1/BPF paper feeder EEPROM error When writing the data, the write data and the read data is not in agreement.
  • Remedy: Defective PF main PWB. Replace the PF main PWB or the BPF main PWB.
    Device damage of EEPROM. Replace the PF main PWB or the BPF main PWB.
  • Code: 1910
  • Description: Paper feeder 2 EEPROM error When writing the data, the write data and the read data is not in agreement.
  • Remedy: Defective PF main PWB. Replace the PF main PWB (Refer to the service manual for the paper feeder).
    Device damage of EEPROM. Replace the PF main PWB (Refer to the service manual for the paper feeder).
  • Code: 1920
  • Description: Paper feeder 3 EEPROM error When writing the data, the write data and the read data is not in agreement.
  • Remedy: Defective PF main PWB. Replace the PF main PWB (Refer to the service manual for the paper feeder).
    Device damage of EEPROM. Replace the PF main PWB (Refer to the service manual for the paper feeder).
  • Code: 1930
  • Description: Paper feeder 4 EEPROM error When writing the data, the write data and the read data is not in agreement.
  • Remedy: Defective PF main PWB. Replace the PF main PWB (Refer to the service manual for the paper feeder).
    Device damage of EEPROM. Replace the PF main PWB (Refer to the service manual for the paper feeder).
  • Code: 2000
  • Description: Main motor drive error The main motor is not stabilized within 2 s after driving starts.
  • Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. Main motor and engine PWB (YC4)
    Defective drive transmission system of the main motor. Check if the rollers and gears rotate smoothly. If not, grease the bushes and gears. Check for broken gears and replace if any.
    Defective main motor. Replace the main motor.
    Defective engine PWB. Replace the engine PWB and check for correct operation.
  • Code: 2010
  • Description: Main motor steady-state error Stable OFF is detected for 2 s continuously after main motor stabilized.
  • Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. Main motor and engine PWB (YC4)
    Defective drive transmission system of the main motor. Check if the rollers and gears rotate smoothly. If not, grease the bushes and gears. Check for broken gears and replace if any.
    Defective main motor. Replace the main motor.
    Defective engine PWB. Replace the engine PWB and check for correct operation.
  • Code: 2200
  • Description: Drum motor drive error (60/55/50 ppm model only) The drum motor is not stabilized within 2 s after driving starts.
  • Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. Drum motor and engine PWB (YC4)
    Defective drive transmission system of the drum motor. Check if the rollers and gears rotate smoothly. If not, grease the bushes and gears. Check for broken gears and replace if any.
    Defective drum motor. Replace the drum motor.
    Defective engine PWB. Replace the engine PWB and check for correct operation.
  • Code: 2210
  • Description: Drum motor steady-state error (60/55/50 ppm model only) Stable OFF is detected for 2 s continuously after drum motor stabilized.
  • Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. Drum motor and engine PWB (YC4)
    Defective drive transmission system of the drum motor. Check if the rollers and gears rotate smoothly. If not, grease the bushes and gears. Check for broken gears and replace if any.
    Defective drum motor. Replace the drum motor.
    Defective engine PWB. Replace the engine PWB and check for correct operation.
  • Code: 2330
  • Description: Fuser pressure release motor error (Over-current) The over-current detection signal of the motor is detected continuously twenty times.
  • Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. Fuser pressure release motor and relay-L PWB(YC11) Relay-L PWB(YC3) and engine PWB(YC2)
    Defective drive transmission system of the fuser pressure release motor. Check if the gears rotate smoothly. If not, grease the bushes and gears. Check for broken gears and replace if any.
    Defective fuser pressure release motor. Replace the fuser pressure release motor.
    Defective PWB. Replace the relay-L PWB or engine PWB.
  • Code: 2340
  • Description: Fuser pressure release motor error (Timeout) The position detection sensor is not detected continuously for 30 s.
  • Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. Fuser pressure release motor and relay-L PWB(YC11) Relay-L PWB(YC1) and engine PWB(YC2)
    Defective drive transmission system of the fuser pressure release motor. Check if the gears rotate smoothly. If not, grease the bushes and gears. Check for broken gears and replace if any.
    Defective fuser pressure release motor. Replace the fuser pressure release motor.
    Defective PWB. Replace the relay-L PWB or engine PWB.
  • Code: 2600
  • Description: PF drive motor 1 error (paper feeder 1) When the PF drive motor is driven, error signal is detected continuously for 2 s.
  • Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. PF drive motor 1 and PF main PWB (YC6)
    Defective drive transmission system of the PF drive motor. Check if the rollers and gears rotate smoothly. If not, grease the bushes and gears. Check for broken gears and replace if any.
    Defective PF drive motor. Replace the PF drive motor 1.
    Defective PF main PWB. Replace the PF main PWB (Refer to the service manual for the paper feeder).
  • Code: 2610
  • Description: PF drive motor 2 error (paper feeder 2) When the PF drive motor is driven, error signal is detected continuously for 2 s.
  • Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. PF drive motor 2 and PF main PWB (YC6)
    Defective drive transmission system of the PF drive motor. Check if the rollers and gears rotate smoothly. If not, grease the bushes and gears. Check for broken gears and replace if any.
    Defective PF drive motor. Replace the PF drive motor 2.
    Defective PF main PWB. Replace the PF main PWB (Refer to the service manual for the paper feeder).
  • Code: 2620
  • Description: PF drive motor 3 error (paper feeder 3) When the PF drive motor is driven, error signal is detected continuously for 2 s.
  • Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. PF drive motor 3 and PF main PWB (YC6)
    Defective drive transmission system of the PF drive motor. Check if the rollers and gears rotate smoothly. If not, grease the bushes and gears. Check for broken gears and replace if any.
    Defective PF drive motor. Replace the PF drive motor 3.
    Defective PF main PWB. Replace the PF main PWB (Refer to the service manual for the paper feeder).
  • Code: 2630
  • Description: PF drive motor 4 error (paper feeder 4) When the PF drive motor is driven, error signal is detected continuously for 2 s.
  • Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. PF drive motor 4 and PF main PWB (YC6)
    Defective drive transmission system of the PF drive motor. Check if the rollers and gears rotate smoothly. If not, grease the bushes and gears. Check for broken gears and replace if any.
    Defective PF drive motor. Replace the PF drive motor 4.
    Defective PF main PWB. Replace the PF main PWB (Refer to the service manual for the paper feeder).
  • Code: 4000
  • Description: Polygon motor synchronization error The polygon motor is not stabilized within 20 s after driving starts.
  • Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. Polygon motor and engine PWB (YC15)
    Defective polygon motor. Replace the laser scanner unit.
    Defective engine PWB. Replace the engine PWB and check for correct operation.
  • Code: 4200
  • Description: BD steady-state error When the value of Register BDSET is 1 after setting Register BDSET as one and passing by BD1 cycle.
  • Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. APC PWB(YC1) and engine PWB (YC16) APC PWB(YC2) and PD PWB(YC1)
    Defective PD PWB. Replace the laser scanner unit.
    Defective engine PWB. Replace the engine PWB and check for correct operation.
  • Code: 5100
  • Description: Chager current error When the current value measured at the time of potential adjustment is less than 20 uA.
  • Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. Chager unit and high voltage PWB High voltage PWB (YC101) and engine PWB (YC19)
    Defective high voltage PWB. Replace the high voltage PWB and check for correct operation.
    Defective engine PWB. Replace the engine PWB and check for correct operation.
  • Code: 6000
  • Description: Broken fuser heater wire The detection temperature of fuser thermistor 2 is 100 °C/ 212°F or less after the fuser heater lamp has been turned on continuously for 30 s.
  • Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. Fuser heater and power source PWB (YC2) Fuser thermistor and Fuser thermistor connect PWB(YC1 and YC2) Fuser thermistor connect PWB(YC3) and engine PWB (YC21)
    Deformed connector pin.
    Defective triac.
    Fuser thermostat triggered. Reinsert the fuser unit.
    Broken fuser heater wire. Reinsert the fuser unit.
    Defective engine PWB. Replace the engine PWB and check for correct operation.
  • Code: 6020
  • Description: Abnormally high fuser thermistor 2 temperature The detection temperature of fuser thermistor 2 is higher than 235°C/455°F. In a heater-off state, the detection temperature of fuser thermistor 2 is higher than 195°C/383°F after the detection temperature of fuser thermistor 2 was 155°C/311°F or less.
  • Remedy: Deformed connector pin.
    Defective triac.
    Shorted fuser thermistor. Replace the fuser unit.
    Defective engine PWB. Replace the engine PWB and check for correct operation.
  • Code: 6030
  • Description: Broken fuser thermistor 2 wire A/D value of the fuser thermistor 2 exceeds 1019 bit continuously for 4 s during warming up.
  • Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. Fuser thermistor and fuser thermistor connect PWB(YC2) Fuser thermistor connect PWB(YC3) and engine PWB (YC21)
    Deformed connector pin.
    Defective triac.
    Defective fuser thermistor. Replace the fuser unit.
    Defective engine PWB. Replace the engine PWB and check for correct operation.
  • Code: 6120
  • Description: Abnormally high fuser thermistor 1 temperature The detection temperature of fuser thermistor 1 is higher than 245°C/473°F. In a heater-off state, the detection temperature of fuser thermistor 1 is higher than 195°C/383°F after the detection temperature of fuser thermistor 1 was 155°C/311°F or less.
  • Remedy: Deformed connector pin.
    Defective triac.
    Shorted fuser thermistor. Replace the fuser unit.
    Defective engine PWB. Replace the engine PWB and check for correct operation.
  • Code: 6130
  • Description: Broken fuser thermistor 1 wire A/D value of the fuser thermistor 1 exceeds 1019 bit continuously for 4 s during warming up.
  • Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. Fuser thermistor and fuser thermistor connect PWB(YC1) Fuser thermistor connect PWB(YC3) and engine PWB (YC21)
    Deformed connector pin.
    Defective triac.
    Defective fuser thermistor.
    Defective engine PWB. Replace the engine PWB and check for correct operation.
  • Code: 6400
  • Description: Zero-cross signal error While fuser heater control is performed, the zero-cross signal is not input within 2 s.
  • Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. Power source PWB (YC3) and engine PWB (YC1)
    Defective power source PWB or engine PWB. Replace the power source PWB or the engine PWB and check for correct operation.
  • Code: 7100
  • Description: Toner sensor error Sensor output value of 930 or more continuously for 5 s.
  • Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. Toner sensor and drum PWB (YC3) Drum connect PWB(YC2) and relay-L PWB (YC3) Relay-L PWB(YC1) and engine PWB (YC2)
    Defective toner sensor. Replace the developer unit.
    Defective engine PWB. Replace the engine PWB and check for correct operation.
  • Code: 7400
  • Description: Developer unit non-installing error Sensor output value of 31 or less continuously for 5 s.
  • Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. Toner sensor and drum PWB (YC3) Drum connect PWB(YC2) and relay-L PWB (YC3) Relay-L PWB(YC1) and engine PWB (YC2)
    Defective toner sensor. Replace the developer unit.
    Defective engine PWB. Replace the engine PWB and check for correct operation.
  • Code: 7410
  • Description: Drum unit type mismatch error The drum PWB EEPROM does not communicate normally. Absence of the drum unit is detected.
  • Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. Drum unit and drum connect PWB (YC1) Drum connect PWB(YC2) and relay-L PWB (YC3) Relay-L PWB(YC1) and engine PWB (YC2)
    Defective toner sensor. Replace the drum unit.
    Defective engine PWB. Replace the engine PWB and check for correct operation.
  • Code: 7800
  • Description: Broken external thermistor wire The average of thermistor output value of 93 or less.
  • Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. Operation PWB (YC1) and engine PWB (YC17)
    Defective temperature sensor. Replace the operation PWB.
  • Code: 7810
  • Description: Short-circuited external thermistor wire The average of thermistor output value of 930 or more.
  • Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. Operation PWB (YC1) and engine PWB (YC17)
    Defective temperature sensor. Replace the operation PWB.
  • Code: 7900
  • Description: Drum unit EEPROM error No response is issued from the device in reading/writing for 5 ms or more and this problem is repeated five times successively. Mismatch of reading data from two locations occurs eight times successively. Mismatch between writing data and reading data occurs eight times successively.
  • Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. Drum unit and drum connect PWB (YC1) Drum connect PWB(YC2) and relay-L PWB (YC3) Relay-L PWB(YC1) and engine PWB (YC2)
    Defective drum unit. Replace the drum unit.
  • Code: F000
  • Description: Main PWB — operation PWB communication error
  • Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. Operation PWB(YC1) and engine PWB (YC17)
    Defective main PWB. Turn the main power switch off/on to restart the machine. If the error is not resolved, replace main PWB.
    Defective operation PWB. Replace the operation PWB and check for correct operation.
  • Code: F000
  • Description: CF000 will be displayed if * notes progress is carried out for a definite period of time with a Welcome screen.The communication fault between Panel-Main boardsCommunication fault between Panel Core-Main Core Notes 2
  • Remedy: (1) Check the harness, and the connection state of a connector between Panel<=>Main boards, and perform an operation check. (2) Check contact of a DDR memory (extracting) and perform an operation check. If exchangeable, it will exchange and will perform an operation check. (3) U021 Controller backup initialization is carried out and an operation check is performed. (4) Exchange a Main board and perform an operation check. (5) Exchange a PanelMain board and perform an operation check. (6) It will get, if USBLOG is obtainable, and contact service headquarters. 1. Panel <=> Main IF (Engine PWB Relay) Main PWB: YC2 Engine PWB: YC20,YC30 Panel PWB: YC1 2. DDR memory Main PWB: YS1
  • Code: F010
  • Description: Main PWB checksum error
  • Remedy: Defective main PWB. Turn the main power switch off/on to restart the machine. If the error is not resolved, replace main PWB.
  • Code: F020
  • Description: Main PWB RAM checksum error
  • Remedy: Defective main memory (RAM) in main PWB Turn the main power switch off/on to restart the machine. If the error is not resolved, replace main PWB.
    Defective expended memory (DIMM) Replace the expansion memory (DIMM). Also in the case of the capacity besides specification, it displays.
  • Code: F040
  • Description: Main PWB — print engine communication error
  • Remedy: Defective main PWB. Turn the main power switch off/on to restart the machine. If the error is not resolved, replace main PWB.
    Defective engine PWB. Replace the engine PWB and check for correct operation.
  • Code: F050
  • Description: Print engine ROM checksum error
  • Remedy: Defective engine PWB. Turn the main power switch off/on to restart the machine. If the error is not resolved, replace engine PWB.
  • Code: F15X
  • Description: Abnormality detecting in an authentication device control section
  • Remedy: (1) Check the harness between authentication device <=>Main boards, and the connection situation of a connector, and perform an operation check. (2) Carry out U021 Main backup initialization and perform an operation check. (3) Exchange a Main board and perform an operation check. (4) Get USBLOG and contact service headquarters. 1.Authentication device <=> Main IF Main PWB: YC6 Authentication device: IC card reader etc.
  • Code: F17X
  • Description: Abnormality detecting in a printer data control part
  • Remedy: (1) U021 Controller backup initialization is carried out and an operation check is performed. (2) Exchange a Main board and perform an operation check. (3) Get USBLOG and contact service headquarters.
  • Code: F18X
  • Description: Abnormality detecting in a Video control section
  • Remedy: (1) Check the harness between Engine<=>Main boards, and the connection state of a connector, and perform an operation check. (2) U021 Controller backup initialization is carried out and an operation check is performed. (3) Exchange an Engine board and perform an operation check. (4) Exchange a Main board and perform an operation check. (5) Get USBLOG and contact service headquarters.
  • Code: F1DX
  • Description: Abnormality detecting of the image memory Management Department
  • Remedy: (1) U021 Controller backup initialization is carried out and an operation check is performed. (2) Exchange a Main board and perform an operation check. (3) Get USBLOG and contact service headquarters.
  • Code: F21X, F22X, F23X
  • Description: Abnormality detecting in an image-processing part
  • Remedy: (1) Check contact of a DDR memory and perform an operation check. (2) Carry out U021 Main backup initialization and perform an operation check. (3) Exchange a Main board and perform an operation check. (4) Get USBLOG and contact service headquarters.
  • Code: F24X
  • Description: Abnormality detecting in the system Management Department
  • Remedy: (1) Check contact of a DDR memory and perform an operation check. (2) Carry out U021 Main backup initialization and perform an operation check. (3) Exchange a Main board and perform an operation check. (4) Get USBLOG and contact service headquarters * F248 is the abnormalities of a printer process.In recurring by specific printer data, please give me cooperation at acquisition of capture data and USBLOG.
  • Code: F25X
  • Description: Abnormality detecting in a network management department
  • Remedy: (1) U021 Controller backup initialization is carried out and an operation check is performed. (2) Exchange a Main board and perform an operation check. (3) Get USBLOG and contact service headquarters. * It may occur according to a visitor’s network environment
  • Code: F26X, F27X, F28X
  • Description: Abnormality detecting in the system Management Department
  • Remedy: (1) U021 Controller backup initialization is carried out and an operation check is performed. (2) Exchange a Main board and perform an operation check. (3) Get USBLOG and contact service headquarters.
  • Code: F29X, F2AX
  • Description: Abnormality detecting in the system Management Department
  • Remedy: (1) U021 Controller backup initialization is carried out and an operation check is performed. (2) Exchange a Main board and perform an operation check. (3) Get USBLOG and contact service headquarters.
  • Code: F2BX, F2CX, F2DX
  • Description: Abnormality detecting in a network control part
  • Remedy: (1) Exchange a Main/Engine PWB and perform an operation check. (2) Get USBLOG and contact service headquarters.(Depending on an analysis result, it is packet capture acquisition)
  • Code: F2EX, F2FX, F30X
  • Description: Abnormality detecting in a network control part
  • Remedy: (1) Exchange a Main/Engine PWB and perform an operation check. (2) Get USBLOG and contact service headquarters.(Depending on an analysis result, it is packet capture acquisition)
  • Code: F31X, F32X
  • Description: Abnormality detecting in a network control part
  • Remedy: (1) Exchange a Main/Engine PWB and perform an operation check. (2) Get USBLOG and contact service headquarters.(Depending on an analysis result, it is packet capture acquisition)
  • Code: F35X
  • Description: Abnormality detecting in the printing controlling Management Department
  • Remedy: (1) Exchange a Main/Engine PWB and perform an operation check. (2) Get USBLOG and contact service headquarters.
  • Code: F38X
  • Description: Abnormality detecting in the authentication authorized Management Department
  • Remedy: (1) Exchange a Main/Engine PWB and perform an operation check. (2) Get USBLOG and contact service headquarters.
  • Code: F3AX, F3BX, F3CX
  • Description: Abnormality detecting in the Entity Management Department
  • Remedy: (1) Exchange a Main/Engine PWB and perform an operation check. (2) Get USBLOG and contact service headquarters
  • Code: F3DX, F3EX, F3FX
  • Description: Abnormality detecting in the Entity Management Department
  • Remedy: (1) Exchange a Main/Engine PWB and perform an operation check. (2) Get USBLOG and contact service headquarters
  • Code: F40X, F41X, F42X
  • Description: Abnormality detecting in the Entity Management Department
  • Remedy: (1) Exchange a Main/Engine PWB and perform an operation check. (2) Get USBLOG and contact service headquarters
  • Code: F43X, F44X, F45X
  • Description: Abnormality detecting in the Entity Management Department
  • Remedy: (1) Exchange a Main/Engine PWB and perform an operation check. (2) Get USBLOG and contact service headquarters
  • Code: F46X
  • Description: Abnormality detecting of a printer rendering part
  • Remedy: (1) Exchange boards and perform an operation check. (2) the acquisition wish of USBLOG — carry out (Depending on the (2) case, it is print capture data acquisition)
  • Code: F47X
  • Description: Abnormality detecting of an image editing processing part
  • Remedy: (1) Exchange a Main/Engine PWB and perform an operation check. (2) Get USBLOG and contact service headquarters.
  • Code: F4DX, F4EX
  • Description: Abnormality detecting in the Entity Management Department
  • Remedy: (1) Exchange a Main/Engine PWB and perform an operation check. (2) Get USBLOG and contact service headquarters
  • Code: F4FX
  • Description: Abnormality detecting in the JOB Management Department
  • Remedy: (1) Exchange a Main/Engine PWB and perform an operation check. (2) Get USBLOG and contact service headquarters.
  • Code: F51X, F52X, F53X
  • Description: Abnormality detecting in a JOB execution part
  • Remedy: (1) Exchange a Main/Engine PWB and perform an operation check. (2) Get USBLOG and contact service headquarters
  • Code: F55X, F56X, F57X
  • Description: Abnormality detecting in a JOB execution part
  • Remedy: (1) Exchange a Main/Engine PWB and perform an operation check. (2) Get USBLOG and contact service headquarters
  • Code: F5FX
  • Description: Abnormality detecting in a service execution part
  • Remedy: (1) Exchange a Main/Engine PWB and perform an operation check. (2) Get USBLOG and contact service headquarters.
  • Code: F62X
  • Description: Abnormality detecting in a service execution part
  • Remedy: (1) Exchange a Main/Engine PWB and perform an operation check. (2) Get USBLOG and contact service headquarters.
  • Code: F63X
  • Description: Abnormality detecting in a device control section
  • Remedy: (1) Exchange a Main/Engine PWB and perform an operation check. (2) Get USBLOG and contact service headquarters.

Перейти к контенту

Модератор: vetal

Прилепить пост

Изменить размер шрифта ↓ВернутьИзменить размер шрифта ↑Всем привет. Данный аппарат выдает ошибку 7410. Я понимаю что эта ошибка говорит о плохом контакте на драм, но при включении принтера с открытой крышкой, аппарат выходит в готовность, далее закрываем крышку, и он печатает без проблем, без каких либо дефектов. Принтак продувал, чистил, ничего не помогло, Ставлю другой драм с другой проявкой, та же ошибка, поставил третий драм с другой проявкой выдал ошибку 0180, со старым драмом так же C7410

То, что другие люди говорят обо мне, никак не характеризует меня. Зато отлично характеризует их.

Аватар пользователя

Andreyak777

Избран тонером

  • Не в сети

Прилепить пост

Сообщение kvg » Чт июн 20, 2019 8:56 am

Изменить размер шрифта ↓ВернутьИзменить размер шрифта ↑А стандартное решение проблемы не помогает?

Выключите принтер. Откройте левую дверь и нажмите на барабан, пока он не защелкнется на месте. Снова включите принтер, аппарат войдет в готовность.

Аватар пользователя

kvg

Администратор сайта и форума

  • Не в сети
  • Сайт
  • Персональный альбом



Прилепить пост

Сообщение Andreyak777 » Чт июн 20, 2019 1:08 pm

То, что другие люди говорят обо мне, никак не характеризует меня. Зато отлично характеризует их.

Аватар пользователя

Andreyak777

Избран тонером

  • Не в сети

Прилепить пост

Сообщение Andreyak777 » Чт июн 20, 2019 1:12 pm

То, что другие люди говорят обо мне, никак не характеризует меня. Зато отлично характеризует их.

Аватар пользователя

Andreyak777

Избран тонером

  • Не в сети


Прилепить пост

Сообщение Andreyak777 » Чт июн 20, 2019 2:47 pm

То, что другие люди говорят обо мне, никак не характеризует меня. Зато отлично характеризует их.

Аватар пользователя

Andreyak777

Избран тонером

  • Не в сети

Прилепить пост

Сообщение pc-porta » Чт июн 20, 2019 3:24 pm

Изменить размер шрифта ↓ВернутьИзменить размер шрифта ↑

Andreyak777 писал(а):Если была бы проблема в контактах, грязь там и все такое, почему он тогда нормально печатает когда загружается с открытой крышкой??

люфтит у Вас драм (шатает его) при закрывании крышки …

Драм совместимка или оригинал ?
Контакты чють подвытянуть в драме или принтаке … для лучшего и надёжного контакта :))

Аватар пользователя

pc-porta

Форумный оракул

  • Не в сети
  • Персональный альбом

Прилепить пост

Сообщение dviz » Чт июн 20, 2019 7:14 pm

Изменить размер шрифта ↓ВернутьИзменить размер шрифта ↑

Andreyak777 писал(а):DK3130 изначально стоял, с ним все работало

Оно конечно, хорошо, но это ж не родной — может глюк какой — там в нём плата сопряжения маленькая с микрухой(кто-то на форуме уже писал, что они иногда дохнут) и датчик регистрации лишний (можно попробовать его отключить).
Плюс ещё по 0180 — проверить в U004 не сбойнули ли серийные номера.

Аватар пользователя

dviz

Блуждающий заряд

  • Не в сети
  • Персональный альбом


Прилепить пост

Сообщение dviz » Пт июн 21, 2019 10:54 am

Изменить размер шрифта ↓ВернутьИзменить размер шрифта ↑Да, в 3130 стоит датчик регистрации, в 3100 — нет, и для m3040 — не нужен.

Надо бы для начала узнать с каких аппаратов и какие модели драмов ставились..

Аватар пользователя

dviz

Блуждающий заряд

  • Не в сети
  • Персональный альбом

  Вопрос решен

Прилепить пост

Сообщение dviz » Пт июн 21, 2019 2:57 pm

Изменить размер шрифта ↓ВернутьИзменить размер шрифта ↑Только что была возможность поэксперимениировать.

Вытащил из включенного m3040dn dk-3100, установил dk-3130 — работает. Выключил-включил — ошибка c7410. Вернул dk-3100 обратно — всё норм.

В fs-4100 вместо dk-3130 установил dk-3100 — ошибка замятия бумаги — ожидаемо — ведь в dk-3100 нет датчика регистрации и в аппарате нет..


За это сообщение автора dviz поблагодарил:
Andreyak777
Аватар пользователя

dviz

Блуждающий заряд

  • Не в сети
  • Персональный альбом


Прилепить пост

Сообщение dviz » Пт июн 21, 2019 3:51 pm

Изменить размер шрифта ↓ВернутьИзменить размер шрифта ↑Проблема в данном случае не в самом наличии или отсутствии датчика, а в том что используется не родной драм..

В аппаратах со скоростью 40-45 стр/мин — fs 2100, m3040, p3045 и т.п. — два датчика регистрации в самом аппарате, поэтому датчик в драме не требуется. Во всех остальных — в самом аппарате один датчик и один в драме.

Тут поправлюсь — в fs2100, m3040, p3045 не два, а только один датчик регистрации — до валов регистрации, а в остальных аппаратах два: один — после валов регистрации, и один — в драме.

Последний раз редактировалось dviz Сб июн 22, 2019 3:42 pm, всего редактировалось 1 раз.

Аватар пользователя

dviz

Блуждающий заряд

  • Не в сети
  • Персональный альбом


  • [SCANNER ERROR] Lamp Error Kyocera FS-1016

    мастерчип в форуме Принтеры, МФУ, факсы, копиры формата A4

    3
    6436

    Усатый Полосатый
    Перейти к последнему сообщению
    Вс окт 28, 2018 11:08 pm
  • Kyocera FS-1120d индикатор «Нет бумаги»

    vs-dos в форуме Принтеры, МФУ, факсы, копиры формата A4

    11
    14580

    СТРОНЦИЙ
    Перейти к последнему сообщению
    Вт ноя 02, 2021 2:24 pm
  • Kyocera 1035 «бледная» печать

    srMax в форуме Принтеры, МФУ, факсы, копиры формата A4

    2
    13544

    srMax
    Перейти к последнему сообщению
    Пт янв 23, 2015 2:49 pm
  • Taskalfa 180 ошибка «Е» и «Встряхните картр. с тонером»

    manik.76 в форуме Принтеры, МФУ, копиры формата A3

    3
    9189

    dviz
    Перейти к последнему сообщению
    Пн фев 20, 2017 1:35 pm
  • Kyocera Ecosys M2635dn «поворот» изображения

    Искатель в форуме Принтеры, МФУ, факсы, копиры формата A4

    10
    5752

    MatrixAgent
    Перейти к последнему сообщению
    Ср апр 08, 2020 5:18 am

Вернуться в Принтеры, МФУ, факсы, копиры формата A4

Кто сейчас на форуме

Сейчас этот форум просматривают: нет зарегистрированных пользователей и гости: 131

Все современные копировальные аппараты, мфу и принтеры Kyocera имеют возможность диагностировать все узлы устройства в режиме запуска и во время работы аппарата. По этому, если во время включения или во время работы произошел сбой, то техника Kyocera сможет сообщить о наличии ошибки.

В большинстве случаев у аппаратов Kyocera код ошибки отображается на дисплее, в остальных случаях тип ошибки зависит от последовательности и количества миганий индикаторов.
Если Ваш копировальный аппарат, МФУ или принтер Kyocera выдал на дисплее некий код, то узнать причину, описание возникновения ошибки, а так же в каком узле аппарата стоит искать проблему, Вы можете в этом разделе выбрав интересующую модель из списка.

Но диагностика не решит проблему сбоя аппарата, для этого лучше обратиться к профессиональным и опытным сервисным специалистам компании Kyomart! Позвоните нам по телефону
8 (343) 288-23-45 или отправьте запрос на электронную почту: sales@kyomart.ru , и мы обязательно свяжемся с Вами в кратчайшие сроки.

Код ошибки Описание ошибки Причина ошибки 0030 FAX control PWB system error
Processing with the fax software was disabled due to a hardware problem. Defective FAX PWB. 0070 FAX PWB incompatible detection Error
Abnormal detection of FAX PWB incompatibility In the initial communication with the FAX PWB, any normal communication command is not transmitted. Defective fax software. Defective FAX PWB. 0100 Backup memory device error Defective flash memory. Defective main PWB. 0120 MAC address data error
For data in which the MAC address is invalid. Defective flash memory. Defective engine PWB. 0130 Backup memory read/write error Defective flash memory. Defective control PWB. 0140 Backup memory data error Defective flash memory. Defective control PWB. 0150 Control PWB EEPROM error
Detecting control PWB EEPROM (U17) communication error. Improper installation control PWB EEPROM (U17). Defective control PWB. Data damage of control PWB EEPROM (U17). 0170 Billing counting error Defective control PWB. Data damage of control PWB EEPROM (U17). 0180 Machine number mismatch
Machine number of main and engine does not match. Data damage of control PWB EEPROM (U17). 0420 Paper feeder communication error
Communication error between control PWB and optional paper feeder. Improper installation paper feeder. Defective harness between control PWB (YC30) and paper feeder interface connector, or improper connector insertion. Defective control PWB. Defective harness between PF main PWB (YC5) and paper feeder interface connector, or improper connector insertion. 0830 FAX PWB flash program area checksum error
A checksum error occurred with the program of the FAX PWB. Defective fax software. Defective FAX PWB. 0840 Faults of RTC
The time is judged to go back based on the comparison of the RTC time and the current time or five years or more have passed. Defective control PWB. The battery is disconnected from the control PWB. 0870 FAX PWB to control PWB high capacity data transfer problem
High-capacity data transfer between the FAX PWB and the control PWB of the machine was not normally performed even if the data transfer was retried the specified times. Improper installation FAX PWB. Defective FAX PWB or control PWB. 0920 Fax file system error
The backup data is not retained for file system abnormality of flash memory of the FAX PWB. Defective FAX PWB. Defective PF paper feed motor drive transmission system. Defective PF main motor. Defective control PWB. 1010 Lift motor error
During driving the lift motor, a motor overcurrent signal is detected for 5 s. This error is detected five times successively. Defective bottom plate elevation mechanism in the cassette. Defective connector cable or poor contact in the connector. Defective drive transmission system of the lift motor. Defective lift motor. Defective engine PWB or connect-R PWB. 2000 Main motor error
The main motor ready input is not given for 2 s during the main motor is ON. Defective harness between main motor (CN1) and control PWB (YC17), or improper connector insertion. Defective drive transmission system of the main motor. Defective main motor. Defective control PWB. 2200 Drum motor steady-state error
The drum motor ready input is not given for 2 s during the drum motor is ON. Defective connector cable or poor contact in the connector. Defective drive transmission system of the drum motor. Defective drum motor. Defective engine PWB. 3100 ISU home position error Defective FFC between CCD PWB (YC1) and control PWB (YC8). Defective FFC between control PWB (YC6) and scanner PWB (YC103), or improper FFC insertion. Defective home position sensor. Defective harness between ISU motor and scanner PWB (YC104), or improper connector insertion. Defective ISU motor. 3200 Exposure lamp error
The exposure lamp is not turned on. Defective FFC between scanner PWB (YC103) and control PWB (YC6), or improper FFC insertion. Defective FFC between CCD PWB (YC1) and control PWB (YC8). Defective harness between CCD PWB (YC3) and inverter PWB (YC101), or improper connector insertion. Defective harness between inverter PWB (YC102) and exposure lamp, or improper connector insertion. Defective exposure lamp. Defective inverter PWB. Defective control PWB. 3300 AGC error
After AGC, correct input is not obtained at CCD. Defective FFC between CCD PWB (YC1) and control PWB (YC8). Defective exposure lamp. Defective CCD PWB. Defective control PWB. 3500 Communication error between scanner and ASIC
An error code is detected. Defective connector cable or poor contact in the connector. Defective CCD PWB. Defective main PWB. 4000 Polygon motor (laser scanner unit) error
The polygon motor ready input is not given for 6 s during the polygon motor is ON. Defective harness between polygon motor and control PWB (YC10), or improper connector insertion. Defective laser scanner unit. Defective control PWB. 4200 BD error (laser scanner unit) error BD sensor does not detect laser beam due to condensation on the polygon mirror. Defective laser scanner unit. Defective control PWB. 4700 VIDEO ASIC device error
Mismatch of reading data from two locations occurs eight times successively. Mismatch between writing data and reading data occurs eight times successively. Defective connector cable or poor contact in the connector. Defective main PWB or engine PWB. 4700 VIDEO ASIC device error
Mismatch of reading data from two locations occurs eight times successively. Mismatch between writing data and reading data occurs eight times successively. Defective connector cable or poor contact in the connector. Defective main PWB or engine PWB. 5100 Main charger high-voltage error
Five pages have been printed with the main charger output short-circuited. Drum unit installed incorrectly. Engine PWB installed incorrectly. Defective engine PWB. 6000 Broken fuser heater wire
The temperature does not reach 100°C/212°F after the fuser heater has been turned on continuously for 30 s. The temperature does not rise by 1°C/1.8°F after the fuser heater lamp has been turned on continuously for 15 s during warm-up or at standby.(Only when the detection temperature is less than 200°C.) Defective connector cable or poor contact in the connector. Fuser thermostat triggered. Broken fuser heater wire. 6020 Abnormally high fuser thermistor temperature
Fuser thermistor detects abnormally temperature. Shorted fuser thermistor. Defective control PWB. 6030 Broken fuser thermistor wire
Input from fuser thermistor is 0 (A/D value). Poor contact in the fuser thermistor connector terminals. Broken fuser thermistor wire. Fuser thermistor installed incorrectly. Fuser thermal cutout triggered. Fuser heater lamp installed incorrectly. Broken fuser heater lamp wire. 6220 Abnormally high fuser thermistor 1 temperature
The temperature of the fuser thermistor 1 detects 255°C/491°F or more continuously for 3 s. Shorted fuser thermistor 1. Defective engine PWB. 6230 Broken fuser thermistor 1 wire
average AD value input from fuser thermistor 1 for 1.8 seconds is less than one. Defective connector cable or poor contact in the connector. Broken fuser thermistor 1 wire. Fuser thermostat triggered. Broken fuser heater wire. 6400 Zero cross signal error
The zero cross signal does not reach the control PWB for specified time. Defective harness between high voltage PWB (YC202) and control PWB (YC23), or improper connector insertion. Defective connection between power source PWB (YC103) and high voltage PWB (YC201). Defective power source PWB. Defective control PWB. 7000 Toner motor lock error
During driving the toner motor, a motor overcurrent signal is detected for 5 s. Lump of toner inside toner container. Defective drive transmission system of the toner motor. Defective toner motor. Defective engine PWB. 7410 Drum unit non- installing error The drum unit is not installed or not installed properly. The drum PWB EEPROM does not communicate normally. The drum unit is not installed. Defective connector cable or poor contact in the connector. Defective drum PWB EEPROM. Defective engine PWB. 9500 BRU communication error IPU PWB error 9510 BRU PWB error IPU PWB error 9520 BRU PWB data error IPU PWB error F000 Main PWB — operation panel PWB communication error Defective main PWB. Defective operation panel PWB. F010 Main PWB checksum error Defective main PWB. F020 Main PWB RAM checksum error Defective main memory (RAM) on the main PWB. Defective expanded memory (DIMM). F040 Main PWB — engine PWB communication error Defective main PWB. Defective engine PWB. F041 Main PWB — scanner communication error Defective main PWB. F050 Engine ROM checksum error Defective engine PWB. F051 Scan engine ROM checksum error Defective engine PWB.

Правила форума
Картинки и фотографии (если они нужны в сообщении) надо загружать только как вложения к своему сообщению (через кнопку Добавить файлы). Тогда картинки будут автоматически отображаться в сообщении.

lamac0

Сообщения: 4
Стаж: 3 месяца

KYOCERA P3145DN код ошибки 7410:0035148

Сообщение

lamac0 » 12 окт 2022, 08:49

Всем по привету, при включении данный аппарат говорит обратиться к сервисникам с кодом ошибки 7410:0035148, понимая, что дело где-то в драме зарыто полез копать гуглы, там сказали, что бывает крякает плата на драме, нашел донора, подкинул плату и результата нет, НО! если выдеруть питалово, открыть крышку переднюю, подать питалово, то он работает как ни в чем не бывало, до ребута

Аватара пользователя

dviz

Сообщения: 178
Стаж: 1 год 1 месяц
Откуда: Ярославль
Благодарил (а): 11 раз
Поблагодарили: 22 раза

Репутация:

KYOCERA P3145DN код ошибки 7410:0035148

Сообщение

dviz » 15 окт 2022, 03:41

Если есть донор — то ставьте донора и проверяйте работоспособность. Только хорошо бы конечно быть уверенным, что донор действительно рабочий. Если с открытой крышкой включается, то вероятно он при инициализации не проверяет работоспособность всех компонентов драма, а с закрытой проверяет и что-то его не устраивает — проверьте всё что там подключено к этой платке — датчик тонера, движок подмеса, засветку фотика.

  • 4 Ответы
    157 Просмотры
    Последнее сообщение

    Аватара пользователя

    22 окт 2022, 21:22

  • 1 Ответы
    93 Просмотры
    Последнее сообщение

    Я поленился установить аватар

    19 сен 2022, 07:48

  • 0 Ответы
    53 Просмотры
    Последнее сообщение

    Я поленился установить аватар

    13 дек 2022, 19:30

  • 13 Ответы
    2616 Просмотры
    Последнее сообщение

    Я поленился установить аватар

    03 фев 2022, 15:54

  • 6 Ответы
    2124 Просмотры
    Последнее сообщение

    Аватара пользователя

    02 фев 2022, 11:07

Dima_NSO писал(а):Вообщем пробема вот в чем, было замятие бумаги я вытащил драм-картридж удалил бумагу и вставил его, но он отпечатал пустой лист бумаги. Я решил, что он просто не ровно встал переустановил и он мне выдал ошибку 7410, затем несколько раз пробывал вытаскивать-устанавливать как с тонером так и без него не помогло, самое забавное что даже без драм-картриджа все равно выдает эту ошибку, как мне ее сбросить ?

как вышел из ситуации и вышел ли вообще?

amag1 писал(а):это ошибка драма
аппарат его не видит
на самом драме есть маленькая плата посмотри все контакты

контакты и платку нашел посмотрел выглядят как новые

Понравилась статья? Поделить с друзьями:
  • Ошибка 720 на винде 10
  • Ошибка 720 мегафон модем на windows 10
  • Ошибка 720 как решить
  • Ошибка 720 как исправить подключения windows 10
  • Ошибка 720 и 691