Ошибка kyocera 0210 - Не ошибается лишь тот, кто ничего не делает!

Andreyak777 » Ср окт 10, 2012 7:46 am

То, что другие люди говорят обо мне, никак не характеризует меня. Зато отлично характеризует их.

Andreyak777

Избран тонером

Andreyak777 » Ср окт 10, 2012 8:04 am

То, что другие люди говорят обо мне, никак не характеризует меня. Зато отлично характеризует их.

Andreyak777

Избран тонером

Unicar » Ср окт 10, 2012 10:12 am

Спасибо! Пойду передерну))

Добавлено спустя 1 день 1 час 44 минуты 1 секунду:
Шлейфа нет. Это жесткий разъем( с ним все в порядке), который соединяет эти две платы.
Поменял энжин (донорский)- все заработало.
Всем СПАСИБО!

Unicar

Увидел чернила

Kyocera FS-1120d индикатор «Нет бумаги»

vs-dos в форуме Принтеры, МФУ, факсы, копиры формата A4

11

15143

СТРОНЦИЙ

Вт ноя 02, 2021 2:24 pm
[SCANNER ERROR] Lamp Error Kyocera FS-1016

мастерчип в форуме Принтеры, МФУ, факсы, копиры формата A4

3

6645

Усатый Полосатый

Вс окт 28, 2018 11:08 pm
Kyocera 1035 «бледная» печать

srMax в форуме Принтеры, МФУ, факсы, копиры формата A4

2

13949

srMax

Пт янв 23, 2015 2:49 pm
Taskalfa 180 ошибка «Е» и «Встряхните картр. с тонером»

manik.76 в форуме Принтеры, МФУ, копиры формата A3

3

9655

dviz

Пн фев 20, 2017 1:35 pm
Kyocera Ecosys M2635dn «поворот» изображения

Искатель в форуме Принтеры, МФУ, факсы, копиры формата A4

10

6104

MatrixAgent

Ср апр 08, 2020 5:18 am

Вернуться в Принтеры, МФУ, копиры формата A3

Кто сейчас на форуме

Сейчас этот форум просматривают: нет зарегистрированных пользователей и гости: 19

Источник

Если при работе с копировальном аппаратом у вас возникли проблемы, и система выдает код ошибки, вы можете идентифицировать ее с помощью данной таблицы.
Коды ошибок Kyocera-Mita указаны для более поздних моделей копиров. Если вы являетесь владельцем более ранней модели, необходимо к трехзначному коду ошибки прибавить знак «0».

Общие ошибки

Код ошибки	Описание
0030	Fax control PWB system problem
0070	Fax control PWB incompatibility detection problem
0100	Backup memory read/write problem (main board)
0110	Backup memory data problem (main board)
0120	Drum EEPROM read/write problem (для 2550)
0130	Backup memory read/write problem (main PCB EEPROM) (для 1650/2050/2550)
0140	Backup memory data problem (main PCB EEPROM) (для 1650/2050/2550)
0150	Backup memory read/write problem (engine board)
0160	Backup memory data problem (engine board)
0170	Accounting count problem
0180	Machine number mismatch
0210	Communication problem between the main board and engine board (для KM-1500/1620/2020/1635/2035/1650/2050/2550/6030/8030, FS-1018/1118)
Communication problem between the main board and operation board (для KM-1525/1530/2030/2530/3530/6230/4530/5530/6330/7530)
0240	Printer board PWB communication problem
0250	Scanner network board communication problem
0280	Communication problem between the fax control PWB and main PWB
0320	Side deck communication problem
0340	Finisher communication problem
0410	Optional DP communication problem
0420	Optional first paper feeder communication problem
Large paper deck /paper feed desk communication problem /Side deck communication problem
0440	Finisher communication problem
0450	Mailbox communication problem
0470	Switchback unit communication problem
0500	Optional second paper feeder communication problem
0510	Optional third paper feeder communication problem
0600	DIMM problem (для 2530/3530)
0610	Bitmap (DIMM) problem
0620	Memory input interface problem
0630	DMA problem
0640	Hard disk drive problem
0800	Image processing problem (JAM05 is detected twice)
0820	Fax control PCB CG ROM checksum error
0830	Flash ROM program area checksum error
0860	Fax control PCB software switch checksum error
0870	Fax control PWB to main PWB high capacity data transfer problem
0880	Fax control PWB program archive problem
0890	Fax control PCB CG font archive problem
0900	Fax software incompatibility detection problem
0920	Fax file system error
0960	Developer EEPROM read/write problem (для 2550/6030/8030)
1000	Exposure lamp problem
1010	Lift motor 1 error
1020	Lift motor 2 error
1030	Lift motor 3 error
1040	Lift motor 4 error
1100	Paper deck motor 1 problem [Drawer 3]
1110	Paper deck motor 2 problem [Drawer 4]
1120	Deck right lift position problem
1130	Deck left lift position problem
1140	Side deck lift motor (going up) problem
1150	Side deck lift motor (going down) problem
1160	Large paper deck (paper feed desk) sequence problem
1170	Large paper deck (paper feed desk) incorrect type problem
2000	Main motor problem
Image forming motor problem (для 6230/4530/5530/6330/7530)
2500	Paper feed motor problem
2550	Paper conveying motor problem (для 4530/5530)
2600	Deck conveying motor /desk drive motor problem
2640	Side deck drive motor problem
3100	Scanner carriage problem
3200	Exposure lamp problem
3300	Optical system (AGC) problem
4000	Polygon motor synchronization problem
4010	Polygon motor steady-state problem
4100	BD initialization (A) problem
4110	BD initialization (B) problem
4200	BD steady-state problem
5100	Main charger problem
5110	Transfer/separation high voltage problem
5300	Broken cleaning lamp wire
5500	Drum surface potential sensor problem 1
5510	Drum surface potential sensor problem 2
5600	Drum surface potential problem 1
5610	Drum surface potential problem 2
6000	Broken fixing heater wire
6020	Abnormally high fixing unit thermistor temperature
6030	Broken fixing unit thermistor
6050	Abnormally low fixing unit thermistor temperature
6100	Broken fixing heater wire
6200	Abnormally low fixing unit thermistor temperature
6300	Abnormally high fixing unit thermistor temperature
6400	Zero-crossing signal problem
6410	Fixing unit connector insertion problem
6420	Fixing fuse cut problem
6420	Broken fixing unit thermistor wire
7100	Toner sensor problem
7300	Broken external temperature thermistor wire (для KM-1505/1510/1810/4230/5230/6230)
Toner sensor problem/ Toner hopper problem (для KM-2530/3530/3035/4035/5035/6230/4530/5530/6330/7530/6030/8030)
7310	Short-circuited external temperature thermistor
7400	Image formation unit connector insertion problem
Developing unit connector insertion problem (для 2550)
7410	Drum unit connector insertion problem
7750	Drum type mismatch problem A (для 1635/2035)
7760	Drum type mismatch problem B (для 1635/2035)
7800	Broken external temperature thermistor
7810	Short-circuited external temperature thermistor

KM-1500, FS-1018/1118 (KM-1820)

Код ошибки	Описание
0220	Communication problem between the main board and operation board (для 1018/1118)
F—	Controller system error (для 1018/1118)
F010	ROM checksum error (для 1118)
F012
7980	Waste toner reservoir overflow problem (when the total number of copies is less than 100 thousand sheets)
7990	Waste toner reservoir overflow problem (when the total number of copies is 100 thousand sheets or more)

KM-1505/1510/1810/1525/1530/2030

Код ошибки	Описание
0210	Printer board communication problem (для 1505/1510/1810)
0400	DIMM problem
0410	Bitmap problem
0430	DMA problem
1040	Optical system problem (AGC)

Kyocera-Mita 3035/4035/5035

Код ошибки	Описание
0100	Operation unit PCB backup memory read/write error
0110	Operation unit PCB backup memory data problem
0210	MMI communication problem
0320	Energy save communication problem
7450	Image formation unit fuse cut problem

Kyocera Mita 4230/5230

Код ошибки	Описание
0010	Memory copy PCB 1 communication problem
0030	Memory copy PCB 2 communication problem
0100	RAM/ROM problem
0220	Communication problem between the engine PCB and main PCB
0230	Scanner communication problem
0260	Memory copy PCB 1 communication problem
0320	Large paper deck communication problem /Paper feed desk communication problem
0360	Memory copy PCB 2 communication problem
0370	Communication microcomputer problem
1040	Optical system problem (AGC)
2100	Paper conveying motor problem
2200	Side registration motor problem
2300	Paper feed motor problem
2310	Desk drive motor problem
2410	Upper lift motor problem
2420	Lower lift motor problem
2430	Upper desk lift motor problem
2440	Lower desk lift motor problem
3320	Scanner watchdog problem
3400	Original detection position problem
7400	Toner hopper problem
9200	Deck paper conveying motor problem
9210	Paper deck motor 1 problem
9220	Paper deck motor 2 problem
9230	Right lift position problem
9240	Left lift position problem

Kyocera-Mita 6030/8030

Код ошибки	Описание
0060	Main PWB type mismatch error
0130	Backup memory (EEPROM) device problem
0140	Backup memory (EEPROM) data problem
0220	Scanner communication problem
0330	Relay board communication problem
0460	Duplex unit communication problem
0470	Sheet inserter communication problem (optional document finisher)
0500	Paper feed unit communication error (cassette 1 and 2)
0510	Paper feed unit communication error (cassette 3 and 4)
0700	Side feeder EEPROM error (optional side feeder)
0750	Document finisher EEPROM error
0970	Cleaning unit EEPROM error
1200	Duplex side registration motor error
2100	Developing motor error
2200	Drive motor error
2300	Fuser motor error
2550	Transfer motor error
3210	CIS lamp problem
3310	Optical system (AGC) problem (DP)
3500	Communication error between scanner and SHD
3900	Backup memory read/write error (scanner PWB)
3910
4120	BD initialization (C) problem
7200	Broken drum thermistor wire
7210	Shorted drum thermistor
9040	DP lift motor going up error
9050	DP lift motor going down error
9060	DP EEPROM error
9070	Communication problem between DP and SHD
9080	Communication problem between DP and CIS

Kyocera Mita 6230

Код ошибки	Описание
0010	Memory PCB communication problem
0100	RAM/ROM problem
0260	Memory copy PCB 1 communication problem
0350	Mailbox communication problem
0370	Communication microcomputer problem
0380	Hard disk problem
0390	DIMM problem
1040	Optical system problem (AGC)
2100	Drive motor problem / Paper conveying motor problem
2200	Paper feed motor problem
2300	Large paper deck right lift motor problem
2310	Large paper deck left lift motor problem
2420	Upper lift motor problem
2430	Lower lift motor problem
6500	Broken fixing unit thermistor wire
7200	Broken drum thermistor wire
7210	Shorted drum thermistor
7220	Broken drum heater wire

KyoceraMita 6330/7530

Код ошибки	Описание
1060	Large paper deck left lift motor problem
2550	Drive motor problem
7520	Shorted drum thermistor
7530	Broken drum thermistor wire

Ошибки финишеров

Код ошибки	Описание
8010	Finisher paper conveying motor problem
8030	Finisher (upper) paper conveying belt problem
8140	Finisher tray elevation motor problem /Main tray problem
8170	Finisher front side registration motor problem
8180	Finisher rear side registration motor problem
Finisher rear jogger motor problem (для 4230/5230)
8190	Finisher trailing edge registration motor problem
8210	Finisher stapler motor problem
8220	Finisher rear stapler problem
8300	Document finisher centerfold unit communication problem
8310	Document finisher centerfold unit side registration guide problem
8320	Document finisher centerfold unit centering plate problem
8330	Document finisher centerfold blade problem

Ошибки финишеров KM-2530/3530/3035/4035/5035

Код ошибки	Описание
8300	Booklet stitcher paper ejection motor problem
8310	Booklet stitcher elevation motor problem
8320	Booklet stitcher rear jog motor problem
8330	Booklet stitcher front jog motor problem
8340	Booklet stitcher staple motor problem
8350	Booklet stitcher batch processing motor problem
8360	Booklet stitcher stapler shift motor problem
8370	Booklet stitcher paddle motor problem
8380	Booklet stitcher folding problem
8390	Booklet stitcher backup RAM data problem
8400	Booklet stitcher incorrect type problem
8410	Booklet stitcher punch motor problem
8420	Booklet stitcher shift motor problem
8430	Booklet stitcher punch communication problem
8440	Booklet stitcher punch sensor problem
8450	Booklet stitcher side punch sensor problem
8460	Booklet stitcher punch backup RAM data problem
8470	Booklet stitcher punch dust sensor problem
8480	Booklet stitcher broken punch power source wire problem
8500	Mailbox drive motor problem

Ошибки финишера KM-6230

Код ошибки	Описание
8180	Finisher rear jogger motor problem
8310	Booklet stitcher paper ejection motor problem
8320	Booklet stitcher elevation motor problem
8330	Booklet stitcher jog motor problem
8340	Booklet stitcher staple motor problem
8350	Booklet stitcher stapler unit shift motor problem
8360	Booklet stitcher stack level detection sensor problem
8370	Booklet stitcher punch motor problem
8380	Booklet stitcher punch shift motor problem
8390	Booklet stitcher swing motor problem
8400	Booklet stitcher backup RAM data problem
8410	Booklet stitcher punch unit backup RAM data problem
8420	Booklet stitcher positioning plate motor problem
8430	Booklet stitcher folding motor problem
8440	Booklet stitcher guide motor problem
8450	Booklet stitcher jog motor problem
8460	Booklet stitcher rear staple motor problem
8470	Booklet stitcher front staple motor problem
8480	Booklet stitcher thrust motor problem
8490	Booklet stitcher communication error

Ошибки финишеров KM-6330/7530/6030/8030

Код ошибки	Описание
8000	Document finisher incorrect type problem (для 6330/7530)
8020	Finisher punch motor problem
8040	Finisher lower paper conveying belt problem
8150	Finisher multi job tray problem
8170	Front upper side-registration guide problem
8180	Finisher rear upper side-registration guide problem
8190	Finisher lower side-registration guide problem
8220	Finisher front clincher problem
8230	Finisher rear stapler problem
8240	Finisher rear clincher problem

Источник

Code: C0030
Description: Fax control PWB system problem
Processing with the fax software was disabled due to a hardware or software problem.
Causes: Defective fax control PWB.
Remedy: Replace the fax control PWB and verify the operation.

Code: C0070
Description: Abnormal detection of fax control PWB incompatibility
Fax software is not compatible with main software
Causes: Fax software or main software is something of the other machine.
Remedy: Check the version of the fax software and the main software, upgrade the version to the compatible software.

Code: C0100
Description: Backup memory (EEPROM) device problem (Main PWB)
Reading from or writing to EEPROM cannot be performed.
Causes: Defective main PWB.
Remedy: Replace the main PWB and check for correct operation.

Code: C0110
Description: Backup memory data problem (Main PWB)
Data in the specified area of the backup memory does not match the specified values
Causes: Data damage of EEPROM.
Remedy: Contact the Service Administrative Division.

Code: C0130
Description: Backup memory device problem (Main EEPROM)
Reading from or writing to EEPROM cannot be performed.
Causes: Defective main PWB.
Device damage of EEPROM.
Remedy: Defective main PWB. Replace the main PWB and check for correct operation.
Device damage of EEPROM. Contact the Service Administrative Division.

Code: C0140
Description: Backup memory data problem (Main EEPROM)
Reading data from EEPROM is abnormal.
Causes: Data damage of EEPROM.
Remedy: Contact the Service Administrative Division.

Code: C0150
Description: Backup memory device problem (Engine EEPROM)
Reading from or writing to EEPROM cannot be performed.
Causes: Defective engine PWB.
Device damage of EEPROM.
Remedy: Defective engine PWB. Replace the engine PWB and check for correct operation.
Device damage of EEPROM. Contact the Service Administrative Division.

Code: C0160
Description: Backup memory data problem (Engine EEPROM)
Reading data from EEPROM is abnormal.
Causes: Data damage of EEPROM.
Remedy: Contact the Service Administrative Division.

Code: C0170
Description: Copy counts problem
When the power is turned on, the total count and the scan count are abnormal both on the main PWB and the engine PWB.
Causes: Data damage of EEPROM.
Defective PWB
Remedy: Data damage of EEPROM. Contact the Service Administrative Division.
Defective PWB. Replace the main PWB or engine PWB and check for correct operation.

Code: C0180
Description: Machine number mismatch
Machine number of main PWB and engine PWB does not match.
Causes: Data damage of EEPROM.
Remedy: Contact the Service Administrative Division.

Code: C0210
Description: Communication problem between the main and engine
When the power is turned on, the machine does not detect the low level of SBSY and the high level of SDIR for 10 s.
Causes: Poor contact in the connector terminals.
Defective PWB.
Remedy: Poor contact in the connector terminals. Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable.
Defective PWB. Replace the main PWB or engine PWB and check for correct operation.

Code: C0240
Description: Printer PWB communication problem
The printer PWB does not respond 120 s after the power is turned on.
Causes: Poor contact in the connector terminals.
Defective main PWB.
Remedy: Poor contact in the connector terminals. Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable.
Defective main PWB. Replace the main PWB and check for correct operation.

Code: C0250
Description: Scanner network board communication problem
The scanner network board does not respond.
Causes: Poor contact in the connector terminals.
Defective PWB
Remedy: Poor contact in the connector terminals. Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable.
Defective PWB. Replace the main PWB or scanner network board and check for correct operation.

Code: C0280
Description: Communication problem between the fax control PWB and main PWB
Communication between the fax control PWB and the main PWB of the machine cannot be performed normally.
Causes: Poor contact in the connector terminals.
Defective PWB.
Remedy: Poor contact in the connector terminals. Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable.
Defective PWB. Replace the fax control PWB or main PWB and check for correct operation.

Code: C0410
Description: Document processor communication problem
Communication fails five times succes-sively.
Causes: Document processor installed incorrectly.
Defective PWB.
Remedy: Document processor installed incorrectly. Check the installation state of the document processor and adjust it if it is not properly installed.
Defective PWB. Replace the engine PWB or DP driver PWB and check for correct operation.

Code: C0420
Description: First paper feeder communication problem Communication fails five times succes-sively.
Causes: First paper feeder installed incorrectly.
Defective PWB.
Remedy: First paper feeder installed incorrectly. Check the installation state of the first paper feeder and adjust it if it is not properly installed.
Defective PWB. Replace the engine PWB or cassette main PWB and check for correct operation.

Code: C0440
Description: Built-in finisher communication problem
Communication fails five times successively.
Causes: Poor contact in the connector terminals.
Defective PWB.
Remedy: Poor contact in the connector terminals. Check the connection of connector YC4 on the engine PWB and the connector of the built-in finisher, and the continuity across the connector terminals. Repair or replace if necessary.
Defective PWB. Replace the engine PWB or finisher main PWB and check for correct operation.

Code: C0500
Description: Second paper feeder communication problem
Communication fails five times succes-sively.
Causes: Second paper feeder installed incorrectly.
Defective PWB.
Remedy: Second paper feeder installed incorrectly. Check the installation state of the second paper feeder and adjust it if it is not properly installed.
Defective PWB. Replace the engine PWB or cassette main PWB and check for correct operation.

Code: C0510
Description: Third paper feeder communication problem
Communication fails five times successively.
Causes: Third paper feeder installed incorrectly.
Defective PWB.
Remedy: Third paper feeder installed incorrectly. Check the installation state of the third paper feeder and adjust it if it is not properly installed.
Defective PWB. Replace the engine PWB or cassette main PWB and check for correct operation.

Code: C0610
Description: Bitmap (DIMM) problem
There is a problem with the data or address bus of the bitmap DRAM.
Causes: Defective main PWB.
DIMM installed incorrectly.
Defective DIMM.
Remedy: Defective main PWB. Replace the main PWB and check for correct operation.
DIMM installed incorrectly. Check if the DIMM is inserted into the socket on the main PWB correctly.
Defective DIMM. Replace the DIMM and check for correct operation.

Code: C0630
Description: DMA problem
DMA transmission of compressed, decompressed, rotated, relocated or blanked-out image data does not complete within the specified period of time.
Causes: Defective main PWB.
Remedy: Replace the main PWB and check for correct operation.

Code: C0800
Description: Image processing problem
JAM05 is detected twice.
Causes: Defective main PWB.
Remedy: Replace the main PWB and check for correct operation.

Code: C0820
Description: Fax control PWB CG ROM checksum error
A checksum error occurred with the CG ROM data of the fax control PWB.
Causes: Defective fax control PWB.
Remedy: Replace the fax control PWB and verify the operation.

Code: C0830
Description: Fax control PWB flash program area checksum error
A checksum error occurred with the program of the fax control PWB.
Causes: Defective fax control PWB.
Remedy: Replace the fax control PWB and verify the operation.

Code: C0860
Description: Fax control PWB software switch checksum error
A checksum error occurred with the software switch value of the fax control PWB.
Causes: Defective fax software.
Defective fax control PWB.
Remedy: Defective fax software. Install the fax software.
Defective fax control PWB. Replace the fax control PWB and verify the operation.

Code: C0870
Description: Fax control PWB to main PWB high capacity data transfer problem
High-capacity data transfer between the fax control PWB and the main PWB of the machine was not normally performed even if the data transfer was retried the specified times.
Causes: Poor contact in the connector terminals.
Defective PWB.
Remedy: Poor contact in the connector terminals. Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable.
Defective PWB. Replace the fax control PWB or main PWB and check for correct operation.

Code: C0880
Description: Fax control PWB program archive problem (optional fax)
When power is turned on, the compressed program in the Flash ROM on the fax control PWB was not successfully decompressed.
Causes: Defective fax control PWB.
Remedy: Replace the fax control PWB and verify the operation.

Code: C0890
Description: Fax control PWB CG FONT archive problem (optional fax)
When power is turned on, the compressed CG font in the Flash ROM on the fax control PWB was not successfully decompressed.
Causes: Defective fax control PWB.
Remedy: Replace the fax control PWB and verify the operation.

Code: C0900
Description: Fax software incompatibility detection problem
Version of fax software is not compatible with that of main software.
Causes: Fax software version or main software is earlier.
Remedy: Check the version of the fax software and the main software, upgrade the version to the compatible software.

Code: C0920
Description: Fax file system error
The backup data is not retained for file system abnormality of flash memory of the fax control PWB.
Causes: Defective fax control PWB.
Remedy: Replace the fax control PWB and verify the operation.

Code: C2000
Description: Drive motor problem
A stable state does not continue for 1 s from 1 s after the drive motor is activated.
Causes: Poor contact in the connector terminals.
Defective drive transmission system.
Defective engine PWB.
Defective drive motor.
Remedy: Poor contact in the connector terminals. Check the connection of connector YC6 on the engine PWB and the connector on the drive motor, and the continuity across the connector terminals. Repair or replace if necessary.
Defective drive transmission system. Check if the rollers and gears rotate smoothly. If not, grease the bushings and gears. Check for broken gears and replace if any.
Defective engine PWB. Replace the engine PWB and check for correct operation.
Defective drive motor. Replace the drive motor.

Code: C2200
Description: Drum motor problem
A stable state does not continue for 1 s from 1 s after the drum motor is activated.
Causes: Poor contact in the connector terminals.
Defective drive transmission system.
Defective engine PWB.
Defective drum motor.
Remedy: Poor contact in the connector terminals. Check the connection of connector YC6 on the engine PWB and the connector on the drum motor, and the continuity across the connector terminals. Repair or replace if necessary.
Defective drive transmission system. Check if the rollers and gears rotate smoothly. If not, grease the bushings and gears. Check for broken gears and replace if any.
Defective engine PWB. Replace the engine PWB and check for correct operation.
Defective drum motor. Replace the drum motor.

Code: C3100
Description: Scanner carriage problem
The home position is not correct when the power is turned on or at the start of copying using the table.
Causes: Poor contact in the connector terminals.
Defective home position switch.
Defective scanner motor.
The mirror frame, exposure lamp, or scanner wire is defective.
Defective engine PWB.
Remedy: Poor contact in the connector terminals. Check the connection of connector YC5 on the engine PWB and the connector on the home position switch, and the continuity across the connector terminals. Repair or replace if necessary.
Defective home position switch. Replace the home position switch.
Defective scanner motor. Replace the scanner motor.
The mirror frame, exposure lamp, or scanner wire is defective. Check if the mirror flames and exposure lamp are on the rail. And check the scanner wire winds correctly.
Defective engine PWB. Replace the engine PWB and check for correct operation.

Code: C3200
Description: Exposure lamp problem
Non-lighting of the exposure lamp is detected at the beginning of copying.
Causes: Poor contact in the connector terminals.
Defective exposure lamp.
Incorrect shading position.
Defective PWB.
Remedy: Poor contact in the connector terminals. Check the connection of connector YC16 on the engine PWB and the connector on the inverter PWB, and the continuity across the connector terminals. Repair or replace if necessary.
Defective exposure lamp. Replace the exposure lamp.
Incorrect shading position. Adjust the position of the contact glass (shading plate). If the problem still occurs, replace the home position switch.
Defective PWB. Replace the engine PWB or inverter PWB and check for correct operation.

Code: C3300
Description: AGC problem
After AGC, correct input is not obtained at CCD.
Causes: Poor contact in the connector terminals.
Defective exposure lamp
Defective PWB.
Remedy: Poor contact in the connector terminals. Check the connection of connector YC5 on the main PWB and the connector on the CCD PWB, and the continuity across the connector terminals. Repair or replace if necessary.
Defective exposure lamp. Replace the exposure lamp.
Defective PWB. Replace the main PWB or CCD PWB and check for correct operation.

Code: C4000
Description: Polygon motor synchronization problem
The polygon motor does not reach the stable speed within 20 s of the START signal turning on.
Causes: Poor contact in the connector terminals.
Defective polygon motor.
Defective engine PWB.
Remedy: Poor contact in the connector terminals. Check the connection of connector YC3 on the engine PWB and laser scanner unit, and the continuity across the connector terminals. Repair or replace if necessary.
Defective polygon motor. Replace the laser scanner unit.
Defective engine PWB. Replace the engine PWB and check for correct operation.

Code: C4010
Description: Polygon motor steady-state problem
Stable OFF is detected for 5 s continuously after polygon motor stability.
Causes: Poor contact in the connector terminals.
Defective polygon motor.
Defective engine PWB.
Remedy: Poor contact in the connector terminals. Check the connection of connector YC3 on the engine PWB and laser scanner unit, and the continuity across the connector terminals. Repair or replace if necessary.
Defective polygon motor. Replace the laser scanner unit.
Defective engine PWB. Replace the engine PWB and check for correct operation.

Code: C4200
Description: BD steady-state problem
ASIC detects a BD error for 600 ms after the polygon motor rotation has been stabilized.
Causes: Poor contact in the connector terminals.
Defective laser scanner unit.
Defective engine PWB.
Remedy: Poor contact in the connector terminals. Check the connection of connector YC3 on the engine PWB and laser scanner unit, and the continuity across the connector terminals. Repair or replace if necessary.
Defective laser scanner unit. Replace the laser scanner unit.
Defective engine PWB. Replace the engine PWB and check for correct operation.

Code: C6000
Description: Fuser heater break
The temperature does not reach 70 °C/ 158°F in 15 s before secondary stabilization.
Temperature rise of 1°C/1.8°F does not occur in 5 s before secondary stabilization (except during printing).
Causes: Poor contact in the fuser thermistor connector terminals.
Fuser thermistor installed incorrectly.
Fuser thermostat triggered.
Fuser heater installed incorrectly.
Broken fuser heater wire.
Remedy: Poor contact in the fuser thermistor connector terminals. Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable.
Fuser thermistor installed incorrectly. Check and reinstall if necessary.
Fuser thermostat triggered. Check for continuity. If none, replace the fuser thermostat.
Fuser heater installed incorrectly. Check and reinstall if necessary.
Broken fuser heater wire. Check for continuity. If none, replace the fuser heater.

Code: C6020
Description: Abnormally high fuser thermistor temperature
Fuser thermistor is detected 230°C/ 446°F or more for 40 ms
Causes: Shorted thermistor.
Broken heater control circuit on the power source PWB.
Remedy: Shorted thermistor. Measure the resistance. If it is 0 Ω, replace the thermistor.
Broken heater control circuit on the power source PWB. Replace the power source PWB and check for correct operation.

Code: C6050
Description: Abnormally low fuser thermistor temperature
Fuser thermistor remains below 90°C/ 194°F for 1 s.
Causes: Poor contact in the fuser thermistor connector terminals.
Broken fuser thermistor wire.
Fuser thermistor installed incorrectly.
Fuser thermostat triggered.
Fuser heater installed incorrectly.
Broken fuser heater wire.
Remedy: Poor contact in the fuser thermistor connector terminals. Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable.
Broken fuser thermistor wire. Measure the resistance. If it is ∞, replace the fixing thermistor.
Fuser thermistor installed incorrectly. Check and reinstall if necessary.
Fuser thermostat triggered. Check for continuity. If none, replace the fuser thermostat.
Fuser heater installed incorrectly. Check and reinstall if necessary.
Broken fuser heater wire. Check for continuity. If none, replace the fuser heater.

Code: C6400
Description: Zero-cross signal error
Interrupt of the zero-cross signal does not occur more than 1 s.
Causes: Poor contact in the connector terminals.
Defective power source PWB.
Defective engine PWB
Remedy: Poor contact in the connector terminals. Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable.
Defective power source PWB. Check if the zero-crossing signal is output from YC2-2 on the power source PWB. If not, replace the power source PWB.
Defective engine PWB. Replace the engine PWB if C6400 is detected while YC2-2 on the power source PWB outputs the zero-crossing signal.

Code: C7800
Description: Broken external thermistor wire
The thermistor output value is 0.5 V or less.
Causes: Poor contact in the connector terminals.
Defective humidity sensor.
Remedy: Poor contact in the connector terminals. Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable.
Defective humidity sensor. Replace the cassette PWB and check for correct operation.

Code: C7810
Description: Short-circuited external thermistor wire
The thermistor output value is 4.5 V or more.
Causes: Poor contact in the connector terminals.
Defective humidity sensor
Remedy: Poor contact in the connector terminals. Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable.
Defective humidity sensor. Replace the cassette PWB and check for correct operation.

Code: C8170
Description: Built-in finisher front side registration motor problem
When the front-side registration home-position sensor is turned on during initialization, the sensor did not turn on while it has moved by 106 pulses. When the front-side registration home-position sensor is turned off during initialization, the sensor did not turn on in 3 s.
Causes: The front side registration motor connector makes poor contact.
Defective front side registration motor.
The front side registration home position sensor connector makes poor contact.
Defective front side registration home position sensor.
Defective finisher control PWB.
Remedy: The front side registration motor connector makes poor contact. Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable.
Defective front side registration motor. Replace front side registration motor.
The front side registration home position sensor connector makes poor contact. Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable.
Defective front side registration home position sensor. Replace the front side registration home position sensor.
Defective finisher control PWB. Replace the finisher control PWB and check for correct operation.

Code: C8180
Description: Built-in finisher rear side registration motor problem
When the rear-side registration home-position sensor is turned on during initialization, the sensor did not turn on while it has moved by 106 pulses.
When the rear-side registration home-position sensor is turned off during initialization, the sensor did not turn on in 3 s.
Causes: The rear side registration motor connector makes poor contact.
Defective rear side registration motor.
The rear side registration home position sensor connector makes poor contact.
Defective rear side registration home position sensor.
Defective finisher control PWB.
Remedy: The rear side registration motor connector makes poor contact. Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable.
Defective rear side registration motor. Replace rear side registration motor.
The rear side registration home position sensor connector makes poor contact. Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable.
Defective rear side registration home position sensor. Replace the rear side registration home position sensor.
Defective finisher control PWB. Replace the finisher control PWB and check for correct operation.

Code: C8190
Description: Built-in finisher trailing edge registration motor problem
When the trailing edge registration home-position sensor is turned on during initialization, the sensor did not turn on while it has moved by 106 pulses.
When the trailing edge registration home-position sensor is turned off during initialization, the sensor did not turn on in 3 s.
Causes: The trailing edge registration motor connector makes poor contact.
Defective trailing edge registration motor.
The trailing edge registration home position sensor connector makes poor contact.
Defective trailing edge registration home position sensor.
Defective finisher control PWB.
Remedy: The trailing edge registration motor connector makes poor contact. Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable.
Defective trailing edge registration motor. Replace trailing edge registration motor.
The trailing edge registration home position sensor connector makes poor contact. Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable.
Defective trailing edge registration home position sensor. Replace the trailing edge registration home position sensor.
Defective finisher control PWB. Replace the finisher control PWB and check for correct operation.

Code: C8210
Description: Built-in finisher stapler problem
The stapler home position sensor does not change state from nondetection to detection within 200 ms of the start of stapler motor counterclockwise (forward) rotation. During initialization, the stapler home position sensor does not change state from non-detection to detection within 600 ms of the start of stapler motor clockwise (reverse) rotation.
Causes: The stapler connector makes poor contact.
The stapler is blocked with a staple.
The stapler is broken.
Defective finisher control PWB.
Remedy: The stapler connector makes poor contact. Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable.
The stapler is blocked with a staple. Remove the stapler cartridge, and check the cartridge and the stapling section of the stapler.
The stapler is broken. Replace the front stapler and check for correct operation.
Defective finisher control PWB. Replace the finisher control PWB and check for correct operation.

Источник

Работая с аппаратами Kyocera можно столкнуться с неисправностями, которые появляются на дисплее в виде кода. Но не все ошибки легко исправляются, многие из них требуют серьёзной диагностики и замены деталей.

В этом списке перечислены лишь основные коды ошибок (на самом деле их гораздо больше):

Код ошибки	Причина возникновения
C0100	Backup memory (EEPROM) device problem (main) (не может быть выполнено чтение или запись в EEPROM)
C0110	Backup memory data problem (main) (проблема резервного копирования данных в память)
C0150	Backup memory device problem (engine EEPROM) (проблема в двигателе EEPROM)
C0160	Backup memory data problem (engine EEPROM) (проблема в двигателе EEPROM)
C0170	Copy counts problem (проблема счетчика копий)
C0180	Machine number mismatch (не совпадает номер аппарата и главного двигателя)
C0210	Communication problem between the main and engine (проблема связи между платой и двигателем)
C0240	Printer PWB communication problem (проблема с питанием)
A0410	Document processor communication problem (сбой связи процессора)
A0420	First paper feeder communication problem (проблема с первым податчиком бумаги)
A0500	Second paper feeder communication problem (проблема со вторым податчиком бумаги)
A0510	Third paper feeder communication problem (проблема с третьем податчиком бумаги)
C0610	Bitmap (DIMM) problem (проблемы с данными или адресной шиной растрового изображения DRAM)
C0620	Memory input interface problem (проблема памяти интерфейса ввода)
C0630	DMA problem (проблема DMA)
C0800	Image processing problem (проблема обработки изображения)
C2000	Drive motor problem (проблема двигателя привода)
C2200	Drum motor problem (проблема двигателя драма)
C3100	Scanner carriage problem (проблема каретки сканера)
C3200	Exposure lamp problem (проблема лампы экспонирования)
C3300	AGC problem (проблема AGC)
C4000	Polygon motor synchronization problem (проблема синхронизации двигателя полигона)
C4010	Polygon motor steady–state problem (проблема двигателя полигона)
C4200	BD steady–state problem (проблема BD)
C6000	Fuser heater break (неисправность нагревателя печки)
C6020	Abnormally high fuser thermistor temperature (аномально высокая температура термистора в печке)
C6050	Abnormally low fuser thermistor temperature (аномально низкая температура термистора в печке)
C6400	Zero–cross signal error (ошибка нулевого сигнала)
C7800	Broken external thermistor wire (поломка внешних проводов термистора)
C7810	Short–circuited external thermistor wire (короткое замыкание термистора)

Источник

Все современные копировальные аппараты, мфу и принтеры Kyocera имеют возможность диагностировать все узлы устройства в режиме запуска и во время работы аппарата. По этому, если во время включения или во время работы произошел сбой, то техника Kyocera сможет сообщить о наличии ошибки.

В большинстве случаев у аппаратов Kyocera код ошибки отображается на дисплее, в остальных случаях тип ошибки зависит от последовательности и количества миганий индикаторов.
Если Ваш копировальный аппарат, МФУ или принтер Kyocera выдал на дисплее некий код, то узнать причину, описание возникновения ошибки, а так же в каком узле аппарата стоит искать проблему, Вы можете в этом разделе выбрав интересующую модель из списка.

Но диагностика не решит проблему сбоя аппарата, для этого лучше обратиться к профессиональным и опытным сервисным специалистам компании Kyomart! Позвоните нам по телефону
8 (343) 288-23-45 или отправьте запрос на электронную почту: sales@kyomart.ru , и мы обязательно свяжемся с Вами в кратчайшие сроки.

Код ошибки	Описание ошибки	Причина ошибки
0100	Backup memory device error	Defective flash memory. Defective control PWB. Defective flash memory. Defective control PWB.
0120	MAC address data error	Defective flash memory.
0130	Backup memory read/write error	Defective flash memory. Defective control PWB
0140	Backup memory data error	Defective flash memory. Defective control PWB.
0150	Control PWB EEPROM error Detecting control PWB EEPROM (U17) communication error.	Improper installation control PWB EEPROM (U17). Defective control PWB.
0160	Backup memory data error (engine PWB)	Defective EEPROM.PWB. Defective engine PWB.
0170	Billing counting error A checksum error is detected in the main and engine backup memories for the billing counters.	Data damage of EEPROM. Defective PWB. EEPROM.
0190	Backup memory device error (engine PWB)	Defective engine PWB.
0800	Image processing error JAM010x is detected twice.	Defective main PWB.B.
0840	Faults of RTC The time is judged to go back based on the comparison of the RTC time and the current time or five years or more have passed.	The battery is disconnected from the main PWB. Defective main PWB.
1010	Lift motor error (60/50/45 ppm model only) After cassette 1 is inserted, lift sensor does not turn on within 10 s. This error is detected four times successively.	Defective bottom plate elevation mechanism in the cassette. Defective connector cable or poor contact in the connector. Defective drive transmission system of the lift motor. Defective lift motor. Defective engine PWB.
1020	PF lift motor 1 error (paper feeder) After cassette 2 is inserted, PF lift sensor 1 does not turn on. This error is detected four times successively.	Defective bottom plate elevation mechanism in the cassette. Defective connector cable or poor contact in the connector. Defective drive transmission system of the PF lift motor. Defective PF lift motor. Defective PF main PWB.
1030	PF lift motor 2 error (paper feeder) After cassette 3 is inserted, PF lift sensor 2 does not turn on. This error is detected four times successively.	Defective bottom plate elevation mechanism in the cassette. Defective connector cable or poor contact in the connector. Defective drive transmission system of the PF lift motor. Defective PF lift motor. Defective PF main PWB.
1040	PF lift motor 3 error (paper feeder) After cassette 4 is inserted, PF lift sensor 3 does not turn on. This error is detected four times successively.	Defective bottom plate elevation mechanism in the cassette. Defective connector cable or poor contact in the connector. Defective drive transmission system of the PF lift motor. Defective PF lift motor. Defective PF main PWB.
1050	PF lift motor 4 error (paper feeder) After cassette 5 is inserted, PF lift sensor 4 does not turn on. This error is detected four times successively	Defective bottom plate elevation mechanism in the cassette. Defective connector cable or poor contact in the connector. Defective drive transmission system of the PF lift motor. Defective PF lift motor. Defective PF main PWB.
1140	BPF lift motor upward error (Bulk paper feeder) BPF lift maximum sensor does not turn on. The lock signal of the motor is detected continuously three times.	Defective connector cable or poor contact in the connector. Defective drive transmission system of the motor. Defective BPF lift motor. Defective BPF main PWB.
1150	BPF lift motor downward error (Bulk paper feeder) BPF lift minimum sensor does not turn on. The lock signal of the motor is detected continuously three times.	Defective connector cable or poor contact in the connector. Defective drive transmission system of the motor. Defective BPF lift motor. Defective BPF main PWB.
1800	Paper feeder 1 communication error A communication error is detected 10 times in succession.	Improper installation paper feeder. Defective connector cable or poor contact in the connector. Defective engine PWB. Defective PF main PWB.
1810	Paper feeder 2 communication error A communication error is detected 10 times in succession.	Improper installation paper feeder. Defective connector cable or poor contact in the connector. Defective PF main PWB.
1820	Paper feeder 3 communication error A communication error is detected 10 times in succession.	Improper installation paper feeder. Defective connector cable or poor contact in the connector. Defective PF main PWB.
1830	Paper feeder 4 communication error A communication error is detected 10 times in succession.	Improper installation paper feeder. Defective connector cable or poor contact in the connector. Defective PF main PWB.
1900	Paper feeder 1/BPF paper feeder EEPROM error When writing the data, the write data and the read data is not in agreement.	Defective PF main PWB. Device damage of EEPROM.
1910	Paper feeder 2 EEPROM error When writing the data, the write data and the read data is not in agreement.	Defective PF main PWB. Device damage of EEPROM.
1920	Paper feeder 3 EEPROM error When writing the data, the write data and the read data is not in agreement.	Defective PF main PWB. Device damage of EEPROM.
1930	Paper feeder 4 EEPROM error When writing the data, the write data and the read data is not in agreement.	Defective PF main PWB. Device damage of EEPROM.
2000	Main motor drive error The main motor is not stabilized within 2 s after driving starts.	Defective connector cable or poor contact in the connector. Defective drive transmission system of the main motor. Defective main motor. Defective engine PWB.
2010	Main motor steady-state error Stable OFF is detected for 2 s continuously after main motor stabilized.	Defective connector cable or poor contact in the connector. Defective drive transmission system of the main motor. Defective main motor. Defective engine PWB.
2200	Drum motor drive error (60/50/45 ppm model only) The drum motor is not stabilized within 2 s after driving starts.	Defective connector cable or poor contact in the connector. Defective drive transmission system of the main motor. Defective main motor. Defective engine PWB.
2210	Drum motor steady-state error (60/50/45 ppm model only) Stable OFF is detected for 2 s continuously after drum motor stabilized.	Defective connector cable or poor contact in the connector. Defective drive transmission system of the main motor. Defective main motor. Defective engine PWB.
2330	Fuser pressure release motor error (Over-current) (60/50/45 ppm model only) The over-current detection signal of the motor is detected continuously twenty times.	Defective connector cable or poor contact in the connector. Defective drive transmission system of the fuser pressure release motor. Defective fuser pressure release motor. Defective PWB.
2340	Fuser pressure release motor error (Timeout) (60/50/45 ppm model only) The position detection sensor is not detected continuously for 30 s.	Defective connector cable or poor contact in the connector. Defective drive transmission system of the fuser pressure release motor. Defective fuser pressure release motor. Defective PWB.
2600	PF drive motor 1 error (paper feeder 1) When the PF drive motor is driven, error signal is detected continuously for 2 s.	Defective connector cable or poor contact in the connector. Defective drive transmission system of the PF drive motor. Defective PF drive motor. Defective PF main PWB.
2610	PF drive motor 2 error (paper feeder 2) When the PF drive motor is driven, error signal is detected continuously for 2 s.	Defective connector cable or poor contact in the connector. Defective drive transmission system of the PF drive motor. Defective PF drive motor. Defective PF main PWB.
2620	PF drive motor 3 error (paper feeder 3) When the PF drive motor is driven, error signal is detected continuously for 2 s.	Defective harness between PF paper feed motor and PF main PWB (YC4), or improper connector insertion. Defective PF paper feed motor drive transmission system. Defective PF main motor. Defective control PWB.
2630	PF drive motor 4 error (paper feeder 4) When the PF drive motor is driven, error signal is detected continuously for 2 s.	Defective harness between PF paper feed motor and PF main PWB (YC4), or improper connector insertion. Defective PF paper feed motor drive transmission system. Defective PF main motor. Defective control PWB.
4000	Polygon motor (laser scanner unit) error The polygon motor ready input is not given for 6 s during the polygon motor is ON.	Defective harness between polygon motor and control PWB (YC10), or improper connector insertion. Defective laser scanner unit. Defective control PWB.
4200	BD steady-state error When the value of Register BDSET is 1 after setting Register BDSET as one and passing by BD1 cycle.	Defective connector cable or poor contact in the connector. Defective PD PWB. Defective engine PWB.
5100	Chager current error When the current value measured at the time of potential adjustment is less than 20 iA. When the current values in the chager voltage 500V constitute not less than 85% of target current values.	Defective connector cable or poor contact in the connector. Defective high voltage PWB. Defective engine PWB.
6000	Broken fuser heater wire (60/50/45 ppm model) The detection temperature of fuser thermistor 2 is 100 °C/ 212°F or less after the fuser heater lamp has been turned on continuously for 30 s. (40 ppm model) The detection temperature of fuser thermistor 1 is 100 °C/ 212°F or less after the fuser heater lamp has been turned on continuously for 30 s.	Defective connector cable or poor contact in the connector. Deformed connector pin. Defective triac. Fuser thermostat triggered. Broken fuser heater wire. Defective engine PWB.
6020	Abnormally high fuser thermistor 2 temperature (60/50/45 ppm model only) The detection temperature of fuser thermistor 2 is higher than 235°C/455°F. In a heater-off state, the detection temperature of fuser thermistor 2 is higher than 195°C/383°F after the detection temperature of fuser thermistor 2 was 155°C/311°F or less.	Deformed connector pin. Defective triac. Shorted fuser thermistor. Defective engine PWB.
6030	Broken fuser thermistor 2 wire (60/50/45 ppm model only) A/D value of the fuser thermistor 2 exceeds 1019 bit continuously for 4 s during warming up.	Defective connector cable or poor contact in the connector. Deformed connector pin. Defective triac. Defective fuser thermistor. Defective engine PWB.
6120	Abnormally high fuser thermistor 1 temperature (60/50/45 ppm model) The detection temperature of fuser thermistor 1 is higher than 245°C/473°F. In a heater-off state, the detection temperature of fuser thermistor 1 is higher than 195°C/383°F after the detection temperature of fuser thermistor 1 was 155°C/311°F or less. (40 ppm model)	Deformed connector pin. Defective triac. Shorted fuser thermistor. Defective engine PWB.
6130	Broken fuser thermistor 1 wire A/D value of the fuser thermistor 1 exceeds 1019 bit continuously for 4 s during warming up.	Defective connector cable or poor contact in the connector. Deformed connector pin. Defective triac.or pin. Defective fuser thermistor. Defective engine PWB.
6400	Zero-cross signal error While fuser heater control is performed, the zero-cross signal is not input within 2 s.	Defective connector cable or poor contact in the connector. Defective power source PWB or engine PWB.
7000	Toner motor error During driving the toner motor, an over-current detection signal is detected at intervals of 10 ms as for 300 accumulation.	Defective connector cable or poor contact in the connector. Defective toner motor. Defective engine PWB.
7100	Toner sensor error Sensor output value of 930 or more continuously for 5 s.	Defective connector cable or poor contact in the connector. Defective toner sensor. Defective engine PWB.
7400	Developer unit non-installing error Sensor output value of 31 or less continuously for 5 s.r.	Defective connector cable or poor contact in the connector. Defective toner sensor. Defective engine PWB.
7410	Drum unit type mismatch error The drum PWB EEPROM does not communicate normally. Absence of the drum unit is detected.	Defective connector cable or poor contact in the connector. Defective toner sensor. Defective engine PWB.
7800	Broken external thermistor wire The average of thermistor output value of 1016 or more continuously for 160 ms. The average of thermistor output value of 930 or more continuously for 5 s.?	Defective connector cable or poor contact in the connector. Defective temperature sensor.
7810	Short-circuited external thermistor wire The average of thermistor output value of 31 or less continuously for 5 s.	Defective connector cable or poor contact in the connector. Defective temperature sensor.
7900	Drum unit EEPROM error No response is issued from the device in reading/writing for 5 ms or more and this problem is repeated five times successively. Mismatch of reading data from two locations occurs eight times successively. Mismatch between writing data and reading data occurs eight times successively.	Defective connector cable or poor contact in the connector. Defective drum unit.
F000	Main PWB — operation PWB communication error	Defective connector cable or poor contact in the connector. Defective main PWB. Defective operation PWB
F010	Main PWB checksum error	Defective main PWB.
F020	Main PWB RAM checksum error	Defective main memory (RAM) in main PWB Defective expended memory (DIMM)
F040	Main PWB — print engine communication error	Defective main PWB. Defective engine PWB.
F050	Print engine ROM checksum error	Defective engine PWB

Источник