07.08.2010
Вопрос:
В процессе работы на ризографе из-за отсутствия краски, которой пользовался постоянно, я пользовался краской другой фирмы. Купил одну тубу, вставил, работал до окончания этой краски. Ризограф, вроде, нормально работал. Когда кончилась краска, ризограф дал код ошибки d-04-534. Я поставил другую, свою тубу с краской, но ошибка не уходит, ризограф не работает. Пробовал прокраску барабана, разобрал барабан и почистил внутри, те места, где чип тубы совпадает с чипом барабана, но результатов нет. Подскажите, пожалуйста, что можно сделать, может, надо почистить полностью насос и барабан от краски, тогда чем их можно смывать? Или в программировании надо что-то сделать. Заранее вам благодарен. Кадиржан
Ответ:
Ошибка d-04-534 означает, что используется неподходящая краска. Попробуйте сбросить ошибку: нажать (кратковременно) и отпустить кнопку СБРОС — на табло засветятся нули, ошибка сброшена. Если это не поможет, значит дело было в разъеме между барабаном и ризографом, возможно, потребуется замена.
Задайте свой вопрос
Skip to content
Finally a Christmas miracle! Second day into trying to convert one of my drums from Sunflower Yellow to Fluorescent Orange and at last I found a fix that worked.
The tutorial on Stencil.wiki seemed otherwise simple enough.
- Insert new ink tube. – Check
- Hold right and left position arrow keys down and turn on the machine. it will start in Test mode. – Check
and the error message D04-534 appeared. Apparently it means either that the ink tube is incompatible or the code at the bottom of the ink tube has been damaged, so the machine is unable to read it.
(I believe it was here in the sequence that the machine (it’s RZ570EP) for some reason locked the drum into its position, so it was not possible to move it either with the ink tube inside or removed. As the master roll also needed changing and the machine was prompting to have it replaced, I replaced it and after a few restarts the drum unlocked itself. I have no idea whether the master change had anything to do with it or the restarts (test mode and normal) fixed it. Either way it seems not to have been a mechanical, but a software issue of some kind.)
I turned the ink tube into unlocked position and the error message disappeared. So I tried to complete the steps from Stencil.wiki
- entered 117 on number pad
- pressed Start (green button)
- pressed Stop (red button)
- entered 890 on number pad
- pressed Start (green button)
- pressed Stop (red button)
- pressed Reset (yellow button) shortly and restarted the machine (by switching it off and on)
First thing to appear – error message saying that ink tube was not detected or it was of the wrong type. (As the drum still wasn’t properly locked into position, it was hardly surprising, but as soon as I locked it, D04-534 error message reappeared.)
So, after some googling I found a slightly different fix from Fixya for a similar machine (RZ390UI) and this one also worked on mine.
Step-by-step:
- enter Test mode by holding down left and right position arrow keys and turning on the machine
- when the error message D04-534 shows, press yellow reset button
- press ‘C’ on the number pad
- enter 890 and press Start (green button)
- when the machine beeps, press ‘C’ on number pad again and enter 112
- when the machine beeps again, press yellow reset button and hold it down, so the machine will reboot
And voilá, after the reboot there stood ‘Fluoresc. Orange’ in the lower left corner of the display. As the colours are rather similar, I did not clean the drum, but will prefer to see how the transition phase will look on prints. The current ones are still sunflower yellow.
Merry Christmas!
-
03-09-2017
#1
Senior Tech
100+ Posts
- Rep Power
- 30
Good day, I wanted to get some help with a problem I am having with a
with a Riso 390 UI. It is showing an error d-04 534, I look up the error code d-04 534 and found that the ink is wrong. I replace the drum and ink and I am still getting the same error. Any idea what this could be?
-
03-10-2017
#2
Re: Error d-04 534
RZ390UI need Rizo S4254 ink.
259882.jpg
-
03-10-2017
#3
Senior Tech
100+ Posts
- Rep Power
- 30
Re: Error d-04 534
Thanks Liatang,
that is the ink I am using, Can it be that I have to reinstall drum? If so why?mdm
-
03-11-2017
#4
Junior Member
- Rep Power
- 0
Re: Error d-04 534
Hi ….
Why you Replace The Drum What is The Reason ?
-
03-12-2017
#5
Re: Error d-04 534
Probably the RF tag on the ink bottle is bad, unless you accidentally put the wrong color ink in that drum.
-
03-12-2017
#6
Junior Member
- Rep Power
- 0
Re: Error d-04 534
Hi Which Color Did You used Right Now ????
Which Model Do You Have RZ 390 OR EZ 390 ???
-
03-13-2017
#7
Senior Tech
100+ Posts
- Rep Power
- 30
Re: Error d-04 534
Hi right I am using black, no color.
I have tried a new drum and a new toner, but I am still getting the same error.
Could it be a board.mdm
-
03-14-2017
#8
Junior Member
- Rep Power
- 0
Re: Error d-04 534
Originally Posted by mdm
Hi right I am using black, no color.
I have tried a new drum and a new toner, but I am still getting the same error.
Could it be a board.mdm
Hi Check This Test Mode : Activate Test Mode No.9874 to go into the protected area test mode
Drum Code Entry: Inter Code 1210 : To Sets the print drum information on the EEPROM of the Drum PCB.
Range : 0 to 255Setting:[ EZ2/EV2 Series ]
98: B4 99: A4 / Letter
102: Legal / Foolscap[ EZ3/EV3 Series ]
113: A3 114: B4 115: A4 / Letter
117: LedgerDefault : 0
Drum Serial Code Entry 1: Inter Test Code:1211
Inputs thefirst 4 -digits of the print drum serial number
Range : 0 to 9999
Unit : 1
Default : 0Drum Serial Code Entry 2 Inter Test Code :1212
Inputs thelast 4 -digits of the print drum serial number
Range : 0 to 9999
Unit : 1
Default : 0Drum Color Code Entry : Inter Test Code : 1214
Sets the print drum color information on the EEPROM of the Drum PCB.
Setting:0: Not Specified <default>
1: Black
2: Blue
3: Medium Blue
4: Red
5: Bright Red
6: Riso Federal Blue
7: Purple
8: Riso Marine Red
9: Burgundy
10: Green
11: Teal
12: Brown
13: Yellow
14: Light Grey
15: Grey
16: Fluorescence Pink
17: Fluorescence Orange
18: Orange
19: Flat Gold
20: Hunter Green
21: Crimson
30: Custom
31: Order (with specified paper)
32: Order (without specified paper)
63: Any Color
-
4 Weeks Ago
#9
Junior Member
- Rep Power
- 0
Re: Error d-04 534
I am on a RISO SF9450 and this worked for me:
Error: D04-534
Wrong-type Ink Cartridge Installed or Cannot Read Ink Info Replace Ink Cartridge or Contact dealer/Riso Office
Solution:
1: When the printer is off, keep press and holding the left and right buttons, then switch the printer on. It should now show a «TEST MODE» splash-screen on the display,
2: Input number»9874″, and press»Start�,
3: Input number «1214», and press «Start»,
4: Input the number associated to the color, and press «Start�,
Color code: black (1), blue (2), medium blue (3), Red (4), bright red (5), Riso Federal (6), Purple (7), Riso Marine Red (8), Burgundy (9), Green (10), Teal (11), Brown (12), Yellow (13), Light grey (14), Grey (15), Fluorescence Pink (16), Fluorescence Orange (18), Orange (19), Flat Gold (19), Hunter Green (20), Crimson (21), If the color is not listed above, set it to (63).
5: Turn off the printer and turn on again.
Originally Posted by mdm
Re: Error d-04 534Hello all,
I’m experiencing an issue with my EZ221. The ink tube it came with, Black E type S-7124U, is giving me an error code. The steps I’ve taken to fix this issue (http://stencil.wiki/how-convert-z-type-color-drums) are not working.
When entering test mode, the error code d-04 534 comes up. I press reset to clear it, but the code does not clear. The machine beeps and the error code remains. I can’t enter the numbers on the keypad.
Is this ink simply not compatible with this machine? On the package it lists the compatible machines and the EZ221 is not listed.
Please help!