P13c9 ошибка bmw n55

Drives: 2013 BMW X6 xDrive50i

Join Date: Jan 2015

Location: Cincinnati, OH

I have a 2012 F25 with 92k miles. Just recently had an oil change. Then 2 days later got the Drivetrain Malfunction displayed. I went and checked the code:

P13C9: VANOS, exhaust: control fault, camshaft stuck.
From the BMW DTC Sheet:
The diagnostic function monitors the camshaft timing adjustment
Potential Causes — Contaminated oil passage at VANOS solenoid valve
— Oil pressure too low
— Defect in wiring harness to VANOS solenoid valve
— VANOS solenoid valve seized
— VANOS solenoid valve defective

I brought it back to the shop since it was after the oil change and they said it threw the code 5 days prior and hasn’t since, so they wouldn’t worry about it and reset it. I have since got the code coming back every few days. I reset, then it comes back in a few days.

Symptom wise, the car still runs pretty well — tough to tell if performance has changed.

Any thoughts on what this could be? Is it just a coincidence happening post oil change?

Thanks!

Drives: X3, m3

Join Date: Jul 2018

Location: Omaha

Drives: 2013 BMW X6 xDrive50i

Join Date: Jan 2015

Location: Cincinnati, OH

Hope this can help you…. i just solved this a few days ago:

The solenoid replacement did not fix the issue.

I ended up discovering that the root case was the oil filter cap was missing the insert that goes inside of the filter. This was caused from the shop that changed the oil.

Here is also a good VANOS troubleshooting article for anyone, that led me to check this before going deeper.

https://us.autologic.com/news/bmw-va…and-diagnosing

Drives: X3 F25

Join Date: Aug 2017

Location: Chile

Being 2011, you must replace the two defective «VANOS» with the new ones that do not cut the bolts. there is a campaign in bmw.

Drives: BMW F25 3.5d MSport LCI

Join Date: Jul 2017

Location: scotland

may I ask how you found out their is a campaign in bmw

are they recalling ?

Drives: BMW

Join Date: Feb 2014

Location: USA

Drives: 2015 X3 xDrive28d

Join Date: Nov 2013

Location: Oklahoma

This way you don’t have anything done wrong, like earlier this year the BMW dealer who replaced my coolant didn’t remember to replace the coolant cap. After they considered driving 190 miles one way to replace it, they decided to just use UPS overnight

Drives: 2012 X3 35i

Join Date: Apr 2014

Location: New Jersey

Thanks for posting this — I was also missing the insert in the oil filter cap. Must have thrown it out by assident with the filter. This brought the cars idle back to normal and cleared the trouble code initially but it came back the next day.

I ended up taking out and cleaning out the VANOS sensors — one was particularly dirty. At least for once, access to the sensors is easy and the process was fairly painless.

Also your link doesn’t work (it truncates the web address for some reason) but that page is very useful. https://us.autologic.com/news/bmw-va…and-diagnosing

Thanks again — saved me a lot of aggravation.

Drives: X3 F25

Join Date: Aug 2017

Location: Chile

Excellent information, I unfortunately broke a defective vanos. (bolts). but after replacing the vanos with new ones, I got the code «130304 — VANOS, escape: control failure, blocking of the camshaft»
the mechanic solved it, but he never told me how he did it.

Drives: BMW 535, BMW 335

Join Date: Jul 2019

Location: Fort Washington Maryland

Thank you for sharing… This literally just happened to me. I changed my oil and started it up… Within minutes I got the �Drivetrain Malfunction� message. I was dumbfounded. I put the scanner on and it read P13C9 Camshaft Stuck…

Turns out I had mistakenly left the insert to the oil filter housing inside of the �old� filter …. Thanks again…

Drives: 2012 BMW X5

Join Date: Nov 2019

Location: CA

Hi.
I ran into the same issue a week after servicing my vehicle for Oil/Filter. I visited AAMCO who pulled the error code for free (P13C9).

After reading this thread, I took the my X5 back to Jiffy Lube and had them open the oil filter cap in front of me.

The oil filter cap was missing the insert that goes inside of the filter. They order a new cap, reset the error code, and it hasn’t returned since.

THANK YOU for saving me from an unnecessary trip to the mechanic.

Drives: 2013 BMW X3

Join Date: Nov 2020

Location: PA

Drives: 2013 BMW X6 xDrive50i

Join Date: Jan 2015

Location: Cincinnati, OH

Mark — sorry to hear this! Can you provide a few more details?
— how long after your oil change did this happen?
— Did you have issues before the oil change?
— why did you start with the camshaft sensor?
— is oil level filled to the right amount?
— have you already checked the oil filter cap if the cage is missing?
— have you checked the vanos solenoids yet?
— after replacing the camshaft sensor, that caused the engine to no longer start??

Drives: 2013 BMW X3

Join Date: Nov 2020

Location: PA

about 3 weeks later — I had never any issues with oil or any sensors .
Camshaft because it said that it was stack.
I just drained the oil and refill it — I check oil filet cap looks like everything is there.Engine didn�t start after stopping on the side or road .
I cannot locate venous on my x-3

Drives: 2013 BMW X6 xDrive50i

Join Date: Jan 2015

Location: Cincinnati, OH

Have you tried putting back the old camshaft sensor back in and see if that caused the issue of the engine not starting?

The oil pressure low is likely causing the camshaft stuck codes. If the oil filter cap still has the cage inside of it, then i would move on to checking the vanos solenoids — the wiring and if they are dirty. Take a look at the article that we posted earlier for info — https://us.autologic.com/news/bmw-va…and-diagnosing

But what confuses me is if your engine just isn’t starting at all, i would probably troubleshoot that first — battery, starter, alternator? then move on to the other issues

Drives: 2013 BMW X5 35i

Join Date: Jan 2020

Location: Houston