-
2017 Volvo VNL + D13
Every time this truck hits a hill, it generates this code and significantly loses power for the rest of the day. We have done all the basics, like check fuel filters and even changed a harness (I believe) for the EPRV system under the valve cover. ALSO, we got a hold of an EPRV-delete kit and it was installed with reprogramming by Dothan Volvo. Driver took it out on the first load and same problem returned. Any ideas?????? It’s been one thing we can’t solve — and there’s very little info on the Web about this code.SA 16 DTC P228F00
He’s able to get back to speed on flat ground and make his trips but his power is quite reduced. So it’s certainly not a 5 mph derate, and I don’t suspect it’s a derate of any kind because there’s no warning or advisory on the dash saying he’s derated.
He DID have a code that pointed to the particulate-matter sensor, but those allegedly do not cause de-rates or affect performance. Is that also for sure on these D13s? That code is DTC P24B100
Any help or insight would be appreciated!
Attached Files:
-
-
Trucking Jobs in 30 seconds
Every month 400 people find a job with the help of TruckersReport.
-
need to look at pressure sensor on the rail or also it can be caused by one of the pumping injectors working to much or overtime i should say. did volvo say anything about this code in particular.
-
Thank you. That’s a good new avenue for us. They didn’t advise on that code that I know of, but the driver has been the contact. I should ask him for a copy of the paperwork to see if there were any comments.
-
usually every code they have comes with dummy diagnostics is what i call it it will give you an idea of what is causing the fault i would check the fuel psi sensor on the rail they are notorious for failures also harness has to be update with sensor as well.
-
@dbny5000
Have you guys been able to find out the problem that caused that P228F00 code? -
Sadly we are still chasing this problem. He’s still losing power on even tiny hills and still getting the P228F00. I’ve confirmed this morning he has the correct new fuel-rail-pressure sensor in, Part No. 23488939, which is a Delphi component with its own part no. of 28672623. We’ve put that sensor in, changed the harness, done an EPRV delete, and this still happens. Whenever he hits a hill, he can expect the power to drop drastically. Oddly he won’t have the same problem fully loaded and flooring it to build speed on an onramp. The condition lasts for the whole day after that. After a shutoff and restart, it goes away. Because of this, he’s staying in flat states.
We’re wondering about external causes now, even crazy ones, like ping-pong balls or sand in the fuel tank or something restricting fuel flow in a filter housing — anything that would cause erratic fuel pressures. The code description for P228F00 is «Fuel Pressure Regulator Exceeded Learning Limits — Too High, No Sub Type Information.» Is there even really a «fuel-pressure regulator» on the engine??
Thinking of diagnosing with help of a dyno???
STILL STUMPED. Help apprciated.
-
How about Turbo working condition?i meet same code and turbo psi always 15psi around
-
P228F00 DTC Fault Code
Code Meaning
The fuel pressure regulator 1 has exceeded the training limits — too high a pressureIn some technician opinion you have a stuck close valve.
The pressure gets too high and a temporary engine de-rate happens.
The fuel pressure should be regulated by a return valve.
Not my personal opinion. I’m just a driver. Retired driver.
I just asked a friend. Maybe it’ll help you. Maybe not.
Good luck.
![[IMG]](https://www.thetruckersreport.com/truckingindustryforum/threads/help-a-year-with-this-problem-sa-16-dtc-p228f00.2403823/proxy.php?image=https%3A%2F%2Fvolvofaultcodes.com%2Fimages%2Flogo.png&hash=7ac52bad058fcb3ca2b0e972bad08b70)
Trucking Jobs in 30 seconds
Every month 400 people find a job with the help of TruckersReport.
На чтение 6 мин Просмотров 1.4к.
Рассмотрим подробнее
- Техническое описание и расшифровка ошибки P228F
- Симптомы неисправности
- Причины возникновения ошибки
- Как устранить или сбросить код неисправности P228F
- Диагностика и решение проблем
- Топливная система высокого давления
- Топливные магистрали и регулятор
- Датчик давления топлива
- На каких автомобилях чаще встречается данная проблема
- Видео
Код ошибки P228F звучит как «регулятор давления топлива 1 превышает пределы обучения из-за слишком высокого напряжения цепи». Часто, в программах, работающих со сканером OBD-2, название может иметь английское написание «Fuel Pressure Regulator 1 Exceeded Learning Limits – Too High».
Техническое описание и расшифровка ошибки P228F
Этот диагностический код неисправности (DTC) является общим. Ошибка P228F считается общим кодом, поскольку применяется ко всем маркам и моделям транспортных средств. Хотя конкретные этапы ремонта могут несколько отличаться в зависимости от модели.
Сохраненный код P228F означает, что модуль управления трансмиссией (PCM) обнаружил проблему с регулятором давления топлива №1. Проблема заключается в том, что модуль управления трансмиссией (PCM) обнаружил слишком высокое напряжение цепи в электронном регуляторе давления топлива. Напряжение достаточно высокое, из-за этого, в целях безопасности произошла остановка двигателя.
Электронный регулятор давления топлива обычно управляется PCM. Сигнал напряжения аккумуляторной батареи и сигнал заземления используются для управления серводвигателем. Который управляет клапаном, чтобы желаемый уровень давления топлива мог быть при любой работе двигателя.
Когда напряжение подается на серводвигатель электронного регулятора давления топлива, клапан открывается с небольшим шагом, и давление топлива увеличивается. Когда напряжение уменьшается, сервопривод втягивается, а клапан закрывается, соответственно давление топлива снижается.
Датчик давления, обычно расположен на топливной рампе, где находятся топливные форсунки. Это позволяет PCM контролировать давление топлива и соответственно регулировать напряжение регулятора давления.
Регулятор давления топлива и датчик давления топлива могут быть отдельными компонентами. Но чаще всего они объединены в единый корпус и имеющий один электрический разъем.
Если PCM обнаруживает высокое напряжение в цепи регулятора давления топлива 1, которое находится выше предела определенного параметра. То сохраниться код неисправности P228F, и может загореться индикаторная лампа неисправности (MIL). Также, произойдет принудительное отключение двигателя.
Симптомы неисправности
Основным симптомом появления ошибки P228F для водителя является подсветка MIL (индикатор неисправности). Также его называют Check engine или просто «горит чек».
Также они могут проявляться как:
- Загорится контрольная лампа «Check engine» на панели управления (код будет записан в память как неисправность).
- Также могут присутствовать другие связанные коды неисправностей.
- Двигатель может запустить аварийный режим и полностью выключиться.
- Плавающие обороты, а также попытки заглохнуть на холостом ходу.
- Большая потеря мощности под нагрузкой.
- Двигатель глохнет либо плохо заводится.
- Повышенный расход топлива.
- Снижение давления топлива.
Ошибка P228F является довольно серьезной, так как при ее появлении могут возникнуть проблемы с двигателем и управляемостью автомобиля. Низкое давление топлива может привести к различным проблемам, а также вызвать повреждение двигателя и каталитического нейтрализатора.
Причины возникновения ошибки
Код P228F может означать, что произошла одна или несколько следующих проблем:
- Неисправен датчик давления топлива.
- Короткое замыкание в жгуте проводов цепи управления регулятора давления топлива.
- Неисправность регулятора давления топлива.
- Иногда причиной является неисправный модуль PCM.
Как устранить или сбросить код неисправности P228F
Некоторые предлагаемые шаги для устранения неполадок и исправления кода ошибки P228F:
- Подключите сканер к диагностическому порту автомобиля для получения сохраненных кодов.
- Очистите коды ошибок с памяти и проведите тест-драйв автомобиля, чтобы выяснить, появляется ли код P228F снова.
- Проведите визуальный осмотр проводки и разъемов.
- Убедитесь в нормальной работе регулятора на топливной рампе.
- Обратите внимание на датчик давления топлива.
Диагностика и решение проблем
Когда причина ошибки, в данном случае P228F лежит на поверхности и легко исправима, это одно дело. Но иногда случается так, что причину очень трудно обнаружить, поэтому пройдемся по наиболее значимым местам.
Топливная система высокого давления
Проверьте все разъемы и жгуты проводов. Убедитесь, что на них нет погнутых или вывернутых контактов или коррозии. При необходимости замените или отремонтируйте.
Обратите внимание на драйвер топливной форсунки (FID). Если драйвер или топливная форсунка были заменены, FID должен запустить программу повторного обучения. Которая настраивает его на насос высокого давления и топливные форсунки.
Осмотрите систему на предмет утечки топлива, также проверьте уровень масла. Если уровень масла выше нормы и пахнет топливом, ищите утечку в топливной форсунке. Особенно если у вас также присутствуют коды неисправности топливной коррекции или пропуски зажигания.
Если вы не можете найти какие-либо проблемы с топливной системой высокого давления. Но у вас есть другие коды неисправности, связанные с топливной системой. Диагностируйте и устраните их, прежде чем возвращаться к ошибке P228F.
Топливные магистрали и регулятор
Ищите физические повреждения или перегибы топливных магистралей, которые могут вызвать затруднения в подающей или обратной магистрали. Может потребоваться снять топливный фильтр, чтобы определить его на забитость и не нуждается ли он в замене.
Топливо должно свободно течь по направлению потока, указанном стрелкой на топливном фильтре. На некоторых автомобилях фильтр расположен на входе в сам топливный насос, необходимо будет снять модуль. Чтобы определить, много ли в баке, что также может ограничить подачу топлива к насосу.
На автомобилях, оборудованных топливной системой обратного типа, регулятор обычно расположен на самой топливной рампе. Регулятор давления топлива имеет вакуумную линию, которая механически ограничивает подачу топлива в зависимости от величины разрежения, создаваемого двигателем.
Проверьте, нет ли поврежденных или ослабленных вакуумных шлангов к регулятору. Если в вакуумном шланге находится топливо, в регуляторе может быть внутренняя утечка, что приведет к потере давления.
В безвозвратных системах регулятор давления топлива может быть расположен внутри бензобака на модуле топливного насоса, и может потребоваться замена модуля топливного насоса в сборе.
Датчик давления топлива
Проверьте датчик давления топлива, сняв разъем и проверив сопротивление на клеммах, используя вольтомметр. Сопротивление должно быть в пределах заводских спецификаций. Проверить опорное напряжение к датчику давления топлива, оно должно быть около 5 вольт, в зависимости от автомобиля.
Если напряжение не соответствует техническим характеристикам, осмотрите проводку, чтобы определить, есть ли чрезмерное сопротивление в проводе. Оно должно быть очень низким, близким к 0 Ом. Если присутствует сопротивление, возможно, произошло замыкание на массу, и необходимо будет отследить проводку, чтобы определить место замыкания.
Выполнив проверку по этим пунктам, у вас должно получится определить проблему появления ошибки P228F. А после определения, решить ее, не составит труда.
На каких автомобилях чаще встречается данная проблема
Проблема с кодом P228F может встречаться на различных машинах, но всегда есть статистика, на каких марках эта ошибка присутствует чаще. Вот список некоторых из них:
- BMW
- Cadillac
- Chevrolet
- Ford (Форд F-150)
- GMC
- Honda
- Land Rover (Ленд Ровер Рендж Ровер)
- Mercedes (Мерседес ml164, w164)
- Renault
- Volkswagen
- Volvo
С кодом неисправности Р228F иногда можно встретить и другие ошибки. Наиболее часто встречаются следующие: P228A, P228C, P228D, P228E.
Видео
Volvo vehicles, like any other vehicles, also generate many unwarranted error codes. Error codes often occur in heavy duty vehicles due to high torque and high load. The error codes most frequently encountered by users are from from the Adblue system.
When we say Adblue systems, we often think about system that breaks very easily. These systems are often used in heavy loads and commercial vehicles. Lately, it has begun to be used in passenger cars. these systems are not used in most countries, even if they are mandatory in Europe. Because it is not structured correctly. Even the adblue liquid, that this system uses, is very difficult to find on the market. Like we said, the system is unstable and users are having trouble. It is a very difficult situation when the systems breaks in the middle of road . Repair of the system is very costly and you lose precious time. For this reason, users are often looking for solutions. One of the solution is an Adblue Emulator developed by SAIL TECHNOLOGY. It is a permanent solution and will be there right beside you in every situation. Adblue Emulators, which many users prefer, will not let you down.
So what do these emulators do and what information do they give? Below are the benefits and fault code information of the SAIL Technology Adblue Emulator we have listed for you.
The instructional models are designed for: Volvo B11R (3), Volvo B5LH (3), Volvo B5TL (3), Volvo B8R (3), Volvo FH (4).
Attention: Please visit https://canbusemulator.com for more detailed information about diagnostic trouble codes
DTC DTC
DTC Code Name
Type of malfunction
P001676
Crankshaft Position — Correlation with Camshaft Position
Incorrect installation position
P003A99
Turbocharger / turbocharger supercharging control position «A» has exceeded the training threshold
Parameter limit exceeded
P004513
Open in turbocharger / turbocharger supercharging control circuit «A»
Open circuit
P004519
Open in turbocharger / turbocharger supercharging control circuit «A»
Current in the circuit above the threshold
P004577
Open in turbocharger / turbocharger supercharging control circuit «A»
The required position is unattainable
P004591
Open in turbocharger / turbocharger supercharging control circuit «A»
Parametric
P004592
Open in turbocharger / turbocharger supercharging control circuit «A»
Characteristics or malfunctioning
P00459A
Open in turbocharger / turbocharger supercharging control circuit «A»
Working conditions of a component or system
P006964
Correlation of absolute pressure in the reservoir and barometric pressure
Violation of signal reliability
P006E16
Supply voltage control circuit turbocharger / turbocharger «A»
Voltage in the circuit below the threshold
P006E17
Supply voltage control circuit turbocharger / turbocharger «A»
Voltage in the circuit above the threshold
P007011
Outdoor temperature sensor «A»
Short to ground
P007015
Outdoor temperature sensor «A»
Circuit short to battery voltage or break
P008700
The pressure in the fuel distribution pipe / system is too low, row 1
No subtype information
P008800
The pressure in the fuel distribution pipe / system is too high, row 1
No subtype information
P008A00
The pressure in the low-pressure fuel system is too low
No subtype information
P008B00
The pressure in the low-pressure fuel system is too high
No subtype information
P008B97
The pressure in the low-pressure fuel system is too high
The operation of the component or system is difficult or blocked
P009011
Control of fuel pressure regulator 1
Short to ground
P009012
Control of fuel pressure regulator 1
Circuit Short to Battery Voltage
P009013
Control of fuel pressure regulator 1
Open circuit
P009400
A leak in the fuel system — a small leak
No subtype information
P009A00
Air temperature at engine intake — correlation
No subtype information
P009B11
Fuel Pressure Relief Control
Short to ground
P009B12
Fuel Pressure Relief Control
Circuit Short to Battery Voltage
P009B13
Fuel Pressure Relief Control
Open circuit
P009B73
Fuel Pressure Relief Control
The actuator jammed in the closed position
P00AF41
Performance characteristics of the turbocharger / turbocharger supercharger control module «A»
Total checksum error
P00C600
Too low pressure in the fuel distribution pipe — engine crankshaft rotation
No subtype information
P010501
Absolute pressure sensor in the manifold / barometric pressure
General electrical fault
P010512
Absolute pressure sensor in the manifold / barometric pressure
Circuit Short to Battery Voltage
P010513
Absolute pressure sensor in the manifold / barometric pressure
Open circuit
P010562
Absolute pressure sensor in the manifold / barometric pressure
Signal comparison error
P011001
Intake air temperature sensor 1, row 1
General electrical fault
P011011
Intake air temperature sensor 1, row 1
Short to ground
P011013
Intake air temperature sensor 1, row 1
Open circuit
P011501
Engine Coolant Temperature Sensor 1
General electrical fault
P011511
Engine Coolant Temperature Sensor 1
Short to ground
P011513
Engine Coolant Temperature Sensor 1
Open circuit
P01152A
Engine Coolant Temperature Sensor 1
Stuck signal in the range
P012011
Throttle / Pedal Position Sensor «A»
Short to ground
P012012
Throttle / Pedal Position Sensor «A»
Circuit Short to Battery Voltage
P012800
Coolant thermostat (coolant temperature below the thermostat control temperature)
No subtype information
P016800
Fuel temperature in engine too high
No subtype information
P016E00
Control of the fuel pressure in a closed loop at the limit is too high a pressure
No subtype information
P016F00
Controlling the fuel pressure in a closed loop at the limit is too low a pressure
No subtype information
P018501
Fuel temperature sensor «B»
General electrical fault
P018511
Fuel temperature sensor «B»
Short to ground
P018513
Fuel temperature sensor «B»
Open circuit
P018564
Fuel temperature sensor «B»
Violation of signal reliability
P019001
Pressure sensor in the fuel distributor pipe, row 1
General electrical fault
P019011
Pressure sensor in the fuel distributor pipe, row 1
Short to ground
P019013
Pressure sensor in the fuel distributor pipe, row 1
Open circuit
P019062
Pressure sensor in the fuel distributor pipe, row 1
Signal comparison error
P019064
Pressure sensor in the fuel distributor pipe, row 1
Violation of signal reliability
P019511
Engine oil temperature sensor «A»
Short to ground
P019513
Engine oil temperature sensor «A»
Open circuit
P019564
Engine oil temperature sensor «A»
Violation of signal reliability
P01B901
Engine oil temperature sensor «B»
General electrical fault
P01B911
Engine oil temperature sensor «B»
Short to ground
P01B913
Engine oil temperature sensor «B»
Open circuit
P020111
Cylinder 1 nozzle «A»
Short to ground
P020112
Cylinder 1 nozzle «A»
Circuit Short to Battery Voltage
P020113
Cylinder 1 nozzle «A»
Open circuit
P020156
Cylinder 1 nozzle «A»
Invalid / incompatible configuration
P020211
Cylinder 2 injector «A»
Short to ground
P020212
Cylinder 2 injector «A»
Circuit Short to Battery Voltage
P020213
Cylinder 2 injector «A»
Open circuit
P020256
Cylinder 2 injector «A»
Invalid / incompatible configuration
P020311
Cylinder 3 injector «A»
Short to ground
P020312
Cylinder 3 injector «A»
Circuit Short to Battery Voltage
P020313
Cylinder 3 injector «A»
Open circuit
P020356
Cylinder 3 injector «A»
Invalid / incompatible configuration
P020411
Cylinder 4 nozzle «A»
Short to ground
P020412
Cylinder 4 nozzle «A»
Circuit Short to Battery Voltage
P020413
Cylinder 4 nozzle «A»
Open circuit
P020456
Cylinder 4 nozzle «A»
Invalid / incompatible configuration
P020511
Cylinder 5 injector «A»
Short to ground
P020512
Cylinder 5 injector «A»
Circuit Short to Battery Voltage
P020513
Cylinder 5 injector «A»
Open circuit
P020556
Cylinder 5 injector «A»
Invalid / incompatible configuration
P020611
Cylinder 6 nozzle «A»
Short to ground
P020612
Cylinder 6 nozzle «A»
Circuit Short to Battery Voltage
P020613
Cylinder 6 nozzle «A»
Open circuit
P020656
Cylinder 6 nozzle «A»
Invalid / incompatible configuration
P021700
Engine coolant temperature exceeded status
No subtype information
P021800
The condition of the transmission oil temperature rise
No subtype information
P021900
State of excess of engine speed
No subtype information
P023400
Overcharging state of turbocharger / supercharger
No subtype information
P024311
Solenoid of the bypass damper «A» of the turbocharger / supercharger
Short to ground
P024312
Solenoid of the bypass damper «A» of the turbocharger / supercharger
Circuit Short to Battery Voltage
P024313
Solenoid of the bypass damper «A» of the turbocharger / supercharger
Open circuit
P025612
Fuel Injector Diesel Injector
Circuit Short to Battery Voltage
P025614
Fuel Injector Diesel Injector
Short to ground or open
P025692
Fuel Injector Diesel Injector
Characteristics or malfunctioning
P026A00
The efficiency of the charge air cooler is below the threshold
No subtype information
P029800
Excess temperature of engine oil
No subtype information
P029900
Insufficient supercharging of the turbocharger / supercharger
No subtype information
P02CC00
Fuel injector cylinder 1 — determination of the correction at the minimum limit
No subtype information
P02CD00
Fuel injector cylinder 1 — determination of the correction at the maximum limit
No subtype information
P02CE00
Fuel injector cylinder 2 — determination of the correction at the minimum limit
No subtype information
P02CF00
Fuel injector cylinder 2 — determination of the correction at the maximum limit
No subtype information
P02D000
Fuel injector cylinder 3 — determination of the correction at the minimum limit
No subtype information
P02D100
Fuel injector cylinder 3 — determination of the correction at the maximum limit
No subtype information
P02D200
Fuel injector of the cylinder 4 — determination of the correction at the minimum limit
No subtype information
P02D300
Fuel injector cylinder 4 — determination of the correction at the maximum limit
No subtype information
P02D400
Fuel injector cylinder 5 — determination of the correction at the minimum limit
No subtype information
P02D500
Fuel injector cylinder 5 — determination of the correction at the maximum limit
No subtype information
P02D600
Fuel injector of the cylinder 6 — determination of the correction at the minimum limit
No subtype information
P02D700
Fuel injector of the cylinder 6 — determination of the correction at the maximum limit
No subtype information
P02E011
Airflow control at the diesel engine inlet
Short to ground
P02E012
Airflow control at the diesel engine inlet
Circuit Short to Battery Voltage
P02E013
Airflow control at the diesel engine inlet
Open circuit
P02E07C
Airflow control at the diesel engine inlet
Slow reaction
P02E09B
Airflow control at the diesel engine inlet
High / excessive flow
P02E09C
Airflow control at the diesel engine inlet
Low / insufficient flow
P02E601
Diesel Engine Admission Regulator Position Sensor
General electrical fault
P02E612
Diesel Engine Admission Regulator Position Sensor
Circuit Short to Battery Voltage
P02E613
Diesel Engine Admission Regulator Position Sensor
Open circuit
P02E697
Diesel Engine Admission Regulator Position Sensor
The operation of the component or system is difficult or blocked
P02E699
Diesel Engine Admission Regulator Position Sensor
Parameter limit exceeded
P03351F
Crankshaft Position Sensor «A»
Intermittent signal in the circuit
P033531
Crankshaft Position Sensor «A»
Missing signal
P033538
Crankshaft Position Sensor «A»
Incorrect signal frequency
P034031
Camshaft position sensor «A» — row 1 or separate sensor
Missing signal
P034038
Camshaft position sensor «A» — row 1 or separate sensor
Incorrect signal frequency
P04007C
Exhaust gas recirculation flow «A»
Slow reaction
P04009B
Exhaust gas recirculation flow «A»
High / excessive flow
P04009C
Exhaust gas recirculation flow «A»
Low / insufficient flow
P040311
Control of EGR «A»
Short to ground
P040312
Control of EGR «A»
Circuit Short to Battery Voltage
P040313
Control of EGR «A»
Open circuit
P040341
Control of EGR «A»
Total checksum error
P040371
Control of EGR «A»
Driven drive
P040392
Control of EGR «A»
Characteristics or malfunctioning
P040901
The differential pressure sensor EGR
General electrical fault
P040912
The differential pressure sensor EGR
Circuit Short to Battery Voltage
P040913
The differential pressure sensor EGR
Open circuit
P040964
The differential pressure sensor EGR
Violation of signal reliability
P040A01
Temperature sensor «A» of the exhaust gas recirculation system
General electrical fault
P040A11
Temperature sensor «A» of the exhaust gas recirculation system
Short to ground
P040A13
Temperature sensor «A» of the exhaust gas recirculation system
Open circuit
P040A64
Temperature sensor «A» of the exhaust gas recirculation system
Violation of signal reliability
P041A11
Temperature sensor circuit «B» of the exhaust gas recirculation system
Short to ground
P041A12
Temperature sensor circuit «B» of the exhaust gas recirculation system
Circuit Short to Battery Voltage
P041A2A
Temperature sensor circuit «B» of the exhaust gas recirculation system
Stuck signal in the range
P042000
The efficiency of the catalyst system is below the threshold
No subtype information
P047001
The gauge of pressure of exhaust gases «A»
General electrical fault
P047012
The gauge of pressure of exhaust gases «A»
Circuit Short to Battery Voltage
P047013
The gauge of pressure of exhaust gases «A»
Open circuit
P047064
The gauge of pressure of exhaust gases «A»
Violation of signal reliability
P047511
Exhaust Pressure Control Valve «A»
Short to ground
P047512
Exhaust Pressure Control Valve «A»
Circuit Short to Battery Voltage
P047513
Exhaust Pressure Control Valve «A»
Open circuit
P047572
Exhaust Pressure Control Valve «A»
The actuator jammed in the open position
P048011
Fan control circuit 1
Short to ground
P048012
Fan control circuit 1
Circuit Short to Battery Voltage
P048013
Fan control circuit 1
Open circuit
P048613
Sensor «B» of the EGR system
Open circuit
P049D99
Control position «A» EGR exceeded the threshold of training
Parameter limit exceeded
P04D900
Control of the closed loop EGR system at the limit — the flow is too small
No subtype information
P04DA00
Control of the closed loop EGR system at the limit — the flow is too strong
No subtype information
P050011
Vehicle speed by wheel
Short to ground
P050013
Vehicle speed by wheel
Open circuit
P051A01
Crankcase Pressure Sensor
General electrical fault
P051A12
Crankcase Pressure Sensor
Circuit Short to Battery Voltage
P051A13
Crankcase Pressure Sensor
Open circuit
P051A64
Crankcase Pressure Sensor
Violation of signal reliability
P052001
Engine oil pressure switch / relay «A»
General electrical fault
P052012
Engine oil pressure switch / relay «A»
Circuit Short to Battery Voltage
P052013
Engine oil pressure switch / relay «A»
Open circuit
P052064
Engine oil pressure switch / relay «A»
Violation of signal reliability
P052400
Engine oil pressure too low
Engine oil pressure too low
P052607
Fan Speed Sensor Circuit
Mechanical faults
P052612
Fan Speed Sensor Circuit
Circuit Short to Battery Voltage
P053E00
Crankcase pressure — too high
No subtype information
P054001
Control of the inlet air heater «A»
General electrical fault
P054011
Control of the inlet air heater «A»
Short to ground
P054013
Control of the inlet air heater «A»
Open circuit
P054070
Control of the inlet air heater «A»
Drive stuck when on
P05407F
Control of the inlet air heater «A»
Drive stuck when turned off
P054464
Exhaust temperature sensor — Row 1 Sensor 1
Violation of signal reliability
P055A01
Engine oil pressure switch / relay «B»
General electrical fault
P055A12
Engine oil pressure switch / relay «B»
Circuit Short to Battery Voltage
P055A13
Engine oil pressure switch / relay «B»
Open circuit
P055A64
Engine oil pressure switch / relay «B»
Violation of signal reliability
P055F00
Engine oil pressure out of range
No subtype information
P05E311
Parking brake sensor / switch circuit
Short to ground
P05E362
Parking brake sensor / switch circuit
Signal comparison error
P05E364
Parking brake sensor / switch circuit
Violation of signal reliability
P061511
Starter relay
Short to ground
P061512
Starter relay
Circuit Short to Battery Voltage
P061513
Starter relay
Open circuit
P06279C
Fuel pump control «A»
Low / insufficient flow
P064111
Sensor reference voltage «A»
Short to ground
P064112
Sensor reference voltage «A»
Circuit Short to Battery Voltage
P06411C
Sensor reference voltage «A»
Output from the voltage range in the circuit
P065111
Sensor reference voltage «V»
Short to ground
P066601
Internal temperature sensor for control module «A»
General electrical fault
P066611
Internal temperature sensor for control module «A»
Short to ground
P06B016
Sensor supply voltage «A»
Voltage in the circuit below the threshold
P06B017
Sensor supply voltage «A»
Voltage in the circuit above the threshold
P06B316
Sensor supply «B»
Voltage in the circuit below the threshold
P06B317
Sensor supply «B»
Voltage in the circuit above the threshold
P06DA71
Engine Oil Pressure Adjustment
Driven drive
P06E616
Sensor supply voltage «C»
Voltage in the circuit below the threshold
P06E617
Sensor supply voltage «C»
Voltage in the circuit above the threshold
P073021
Recommended transfer
The amplitude of the signal is less than the minimum
P073022
Recommended transfer
The amplitude of the signal above the maximum value
P07307C
Recommended transfer
Slow reaction
P100101
Engine stop switch
General electrical fault
P100111
Engine stop switch
Short to ground
P100112
Engine stop switch
Circuit Short to Battery Voltage
P100190
Engine stop switch
Clogged in the open position
P100192
Engine stop switch
Characteristics or malfunctioning
P100211
Pre-heater heater relay
Short to ground
P100212
Pre-heater heater relay
Circuit Short to Battery Voltage
P100213
Pre-heater heater relay
Open circuit
P100701
Air filter indicator
General electrical fault
P100711
Air filter indicator
Short to ground
P100712
Air filter indicator
Circuit Short to Battery Voltage
P100713
Air filter indicator
Open circuit
P101711
Valve for draining water from fuel
Short to ground
P101E11
The valve of full blocking of the channel of a transmission
Short to ground
P101E12
The valve of full blocking of the channel of a transmission
Circuit Short to Battery Voltage
P101E13
The valve of full blocking of the channel of a transmission
Open circuit
P102111
Volvo Compression Brake Control Circuit (VCB)
Short to ground
P102112
Volvo Compression Brake Control Circuit (VCB)
Circuit Short to Battery Voltage
P102113
Volvo Compression Brake Control Circuit (VCB)
Open circuit
P108600
The oil level is moderately low
No subtype information
P109300
Engine oil pressure is moderately low
No subtype information
P10C011
Volvo Compression Brake Control Circuit (VCB) «2»
Short to ground
P10C012
Volvo Compression Brake Control Circuit (VCB) «2»
Circuit Short to Battery Voltage
P10C013
Volvo Compression Brake Control Circuit (VCB) «2»
Open circuit
P10E100
Differential pressure in particulate filter is critical
No subtype information
P10E200
Differential pressure on particulate filter moderately high
No subtype information
P10F800
Air filter clogged
No subtype information
P10FE00
Clogging of particulate filter — soot accumulation moderately high — row 1
No subtype information
P110400
Factory setting
No subtype information
P110501
Back-up switch circuit «A» of the engine
General electrical fault
P110511
Back-up switch circuit «A» of the engine
Short to ground
P110512
Back-up switch circuit «A» of the engine
Circuit Short to Battery Voltage
P110573
Back-up switch circuit «A» of the engine
The actuator jammed in the closed position
P111600
Absolute pressure sensor in the reservoir is a moderate excess
No subtype information
P111800
Absolute pressure sensor in the collector — a strong excess
No subtype information
P111945
The intake manifold temperature is too high at a moderate level
Failure of program memory
P111A00
Intake manifold temperature too high
No subtype information
P111D00
The engine coolant level is moderately low
No subtype information
P111E00
Engine coolant temperature is moderately high
No subtype information
P112500
Engine oil temperature — moderately high
No subtype information
P112800
The oil pressure for cooling the pistons is moderately low
No subtype information
P112900
Transmission oil temperature moderately high
No subtype information
P112B00
The turbocharger / turbocharger drive temperature «A»
No subtype information
P112E00
Exhaust gas temperature moderately high — row 1
No subtype information
P113411
Air purge valve for fuel injection into the exhaust aftertreatment system
Short to ground
P113413
Air purge valve for fuel injection into the exhaust aftertreatment system
Open circuit
P113472
Air purge valve for fuel injection into the exhaust aftertreatment system
The actuator jammed in the open position
P113473
Air purge valve for fuel injection into the exhaust aftertreatment system
The actuator jammed in the closed position
P113500
Crankcase pressure too high relative to atmospheric pressure
No subtype information
P113600
Error of calibration of the correlation of NOx 1/2 sensors — row 1
No subtype information
P113711
Oil thermostat
Short to ground
P113712
Oil thermostat
Circuit Short to Battery Voltage
P113713
Oil thermostat
Open circuit
P113F11
Idling switch confirmation cable with buffering — VECU side
Short to ground
P113F12
Idling switch confirmation cable with buffering — VECU side
Circuit Short to Battery Voltage
P114000
Volvo Compression Brake Control (VCB) — too low oil temperature
No subtype information
P114101
Idling switch confirmation cable with buffering — ECM side
General electrical fault
P114113
Idling switch confirmation cable with buffering — ECM side
Open circuit
P114123
Idling switch confirmation cable with buffering — ECM side
Constantly low signal level
P114124
Idling switch confirmation cable with buffering — ECM side
Constantly high signal level
P114411
High voltage side of the starter relay
Short to ground
P114412
High voltage side of the starter relay
Circuit Short to Battery Voltage
P114413
High voltage side of the starter relay
Open circuit
P114500
The level of the reducing agent is moderately low
No subtype information
P114700
Pressure in the fuel distribution pipe / system, row 1 — moderately too high
No subtype information
P114B00
The turbocharger / turbocharger drive temperature «A» is too low
No subtype information
P114E00
EGR drive temperature outside the operating range
No subtype information
P115000
Correlation of Sensor / Switch Voltage «A» / «D» Throttle Position / Pedal Position
No subtype information
P115100
Excess temperature of the post-treatment system
No subtype information
P115211
Starting fuel pump
Short to ground
P115212
Starting fuel pump
Circuit Short to Battery Voltage
P115213
Starting fuel pump
Open circuit
P115400
The connection between the bodywork control module «A» and the instrument cluster control module (IPC)
No subtype information
P117311
Low Transmission Range Authorization Valve
Short to ground
P117312
Low Transmission Range Authorization Valve
Circuit Short to Battery Voltage
P117313
Low Transmission Range Authorization Valve
Open circuit
P117401
Transmission range inquiry
General electrical fault
P117411
Transmission range inquiry
Short to ground
P117412
Transmission range inquiry
Circuit Short to Battery Voltage
P117600
Starter motor is deactivated — temperature rise
No subtype information
P117700
Starter motor is deactivated — gearbox is not in neutral position
No subtype information
P117800
The starter motor is deactivated — the gear of the electric motor of the starter motor is stuck
No subtype information
P117900
Starter motor is deactivated — power take-off is active
No subtype information
P117B01
Temperature sensor switch in engine compartment
General electrical fault
P117B11
Temperature sensor switch in engine compartment
Short to ground
P117B12
Temperature sensor switch in engine compartment
Circuit Short to Battery Voltage
P117C00
The requested range of gears is too high
No subtype information
P117D00
Requested driver transfer too low
No subtype information
P117E00
Driver’s request is too high
No subtype information
P117F11
Bypass valve of the hydraulic valve
Short to ground
P117F12
Bypass valve of the hydraulic valve
Circuit Short to Battery Voltage
P117F13
Bypass valve of the hydraulic valve
Open circuit
P203164
Exhaust temperature sensor — Row 1 Sensor 2
Violation of signal reliability
P203A86
Reagent level sensor «A»
Invalid signal
P203F00
Reducer level is low
No subtype information
P204F93
Characteristics of the SCR system — dosing failure
Does not work
P207F9A
Quality of the reducing agent
Working conditions of a component or system
P20D711
Controlling the fuel supply to the exhaust aftertreatment system
Short to ground
P20D713
Controlling the fuel supply to the exhaust aftertreatment system
Open circuit
P20D773
Controlling the fuel supply to the exhaust aftertreatment system
The actuator jammed in the closed position
P20DD01
Fuel pressure sensor for exhaust gas aftertreatment
General electrical fault
P20DD12
Fuel pressure sensor for exhaust gas aftertreatment
Circuit Short to Battery Voltage
P20DD13
Fuel pressure sensor for exhaust gas aftertreatment
Open circuit
P20EE00
The efficiency of the SCR NOx catalyst is below the threshold (row 1)
No subtype information
P20F400
AdBlue consumption is too low
No subtype information
P20F500
Reducer consumption too high
No subtype information
P210900
Performance characteristics of the «A» minimum limiter of the throttle / pedal position
No subtype information
P213600
Correlation of Sensor / Switch Voltage «A» / «C» Throttle Position / Pedal Position
No subtype information
P215A62
Correlation of vehicle speed with wheel speed
Signal comparison error
P215A64
Correlation of vehicle speed with wheel speed
Violation of signal reliability
P216300
Performance characteristics of the maximum limit sensor «A» of the throttle / pedal position
No subtype information
P220012
NOx sensor — series 1 sensor 1
Circuit Short to Battery Voltage
P220013
NOx sensor — series 1 sensor 1
Open circuit
P22001C
NOx sensor — series 1 sensor 1
Output from the voltage range in the circuit
P220064
NOx sensor — series 1 sensor 1
Violation of signal reliability
P220093
NOx sensor — series 1 sensor 1
Does not work
P222601
Barometric pressure circuit
General electrical fault
P222612
Barometric pressure circuit
Circuit Short to Battery Voltage
P222613
Barometric pressure circuit
Open circuit
P222664
Barometric pressure circuit
Violation of signal reliability
P225C00
Characteristics of the NOx sensor — high level signaling — row 1 sensor 1
No subtype information
P225D00
Characteristics of the NOx sensor — low level of the signal — row 1 sensor 1
No subtype information
P225E67
Characteristics of the NOx sensor — high level signaling — row 1 sensor 2
Wrong signal after event
P225F00
Characteristics of the NOx sensor — low level of the signal — row 1 sensor 2
No subtype information
P226401
Water sensor in fuel
General electrical fault
P226411
Water sensor in fuel
Short to ground
P226413
Water sensor in fuel
Open circuit
P228D72
The fuel pressure regulator 1 has exceeded the control limits — too high a pressure
The actuator jammed in the open position
P228E00
The fuel pressure regulator 1 has exceeded the training limits — too low a pressure
No subtype information
P228F00
The fuel pressure regulator 1 has exceeded the training limits — too high a pressure
No subtype information
P229E12
NOx sensor — row 1 sensor 2
Circuit Short to Battery Voltage
P229E13
NOx sensor — row 1 sensor 2
Open circuit
P229E1C
NOx sensor — row 1 sensor 2
Output from the voltage range in the circuit
P229E64
NOx sensor — row 1 sensor 2
Violation of signal reliability
P229E93
NOx sensor — row 1 sensor 2
Does not work
P22FB92
Sensor Specifications NOx — Sensor — Row 1 Sensor 1
Characteristics or malfunctioning
P22FE00
Sensor Specifications NOx — Sensor — Row 1 Sensor 2
No subtype information
P242800
Exhaust gas temperature too high
No subtype information
P242A64
Exhaust temperature sensor — Row 1 Sensor 3
Violation of signal reliability
P244A00
Differential pressure on the diesel particulate filter after-treatment 1 is too small (row 1)
No subtype information
P244B00
The differential pressure on the diesel particulate filter after-treatment 1 is too large (row 1)
No subtype information
P244C00
The exhaust gas temperature is too low to regenerate the particulate filter (row 1)
No subtype information
P245264
Particulate filter pressure sensor «A»
Violation of signal reliability
P245700
Coolant efficiency of the exhaust gas recirculation system is below the threshold value
No subtype information
P246300
Clogged particulate filter — soot accumulation — row 1
No subtype information
P249D00
Control of the injection of the reducing agent in a closed loop at the limit — the flow is too small
No subtype information
P249E00
Injection of the reducing agent in a closed loop at the limit — the flow is too high
No subtype information
P249F92
Excessive time for switching to the closed-loop diesel particulate filter regeneration control mode
Characteristics or malfunctioning
P24A000
Control of DPF regeneration in a closed loop at the limit — the temperature is too low
No subtype information
P24A100
Control of DPF regeneration in a closed loop at the limit — the temperature is too high
No subtype information
P24A200
The regeneration of the diesel particulate filter is not complete (row 1)
No subtype information
P24A400
Clogging of the diesel particulate filter — soot accumulation too large (row 1)
No subtype information
P250A11
Engine oil level sensor
Short to ground
P250A13
Engine oil level sensor
Open circuit
P250F00
Engine oil level too low
No subtype information
P253901
Low Fuel Pressure Sensor Circuit
General electrical fault
P253912
Low Fuel Pressure Sensor Circuit
Circuit Short to Battery Voltage
P253913
Low Fuel Pressure Sensor Circuit
Open circuit
P255601
Engine Coolant Level Sensor / Relay
General electrical fault
P255611
Engine Coolant Level Sensor / Relay
Short to ground
P255612
Engine Coolant Level Sensor / Relay
Circuit Short to Battery Voltage
P255613
Engine Coolant Level Sensor / Relay
Open circuit
P256000
Engine Coolant Level — Low
No subtype information
P256214
Sensor «A» turbocharger supercharging control position
Short to ground or open
P256214
Sensor «A» turbocharger supercharging control position
Short to ground or open
P259C00
Excessive time for entering the supercharging control of the turbocharger «A» in a closed loop
No subtype information
P25A911
Control oil supply for cooling pistons
Short to ground
P25A912
Control oil supply for cooling pistons
Circuit Short to Battery Voltage
P25A913
Control oil supply for cooling pistons
Open circuit
P25A971
Control oil supply for cooling pistons
Driven drive
P25AE00
The oil pressure for cooling the pistons is too low
No subtype information
P260011
Coolant Pump Control Circuit / Break
Short to ground
P260012
Coolant Pump Control Circuit / Break
Circuit Short to Battery Voltage
P260013
Coolant Pump Control Circuit / Break
Open circuit
P268111
Control of the bypass valve «A» of the engine coolant
Short to ground
P268112
Control of the bypass valve «A» of the engine coolant
Circuit Short to Battery Voltage
P268113
Control of the bypass valve «A» of the engine coolant
Open circuit
P269711
Injection Fuel Injector «A»
Short to ground
P269713
Injection Fuel Injector «A»
Open circuit
P269773
Injection Fuel Injector «A»
The actuator jammed in the closed position
P26977A
Injection Fuel Injector «A»
Fluid leakage or seal failure
P2A1612
Control unit «D» fuel flow meter injection pump (cam / rotor / nozzle)
Circuit Short to Battery Voltage
P2A1614
Control unit «D» fuel flow meter injection pump (cam / rotor / nozzle)
Short to ground or open
P2A1692
Control unit «D» fuel flow meter injection pump (cam / rotor / nozzle)
Characteristics or malfunctioning
P2A1E12
Control unit «F» fuel flow meter injection pump (cam / rotor / injector)
Circuit Short to Battery Voltage
P2A1E14
Control unit «F» fuel flow meter injection pump (cam / rotor / injector)
Short to ground or open
P2A1E92
Control unit «F» fuel flow meter injection pump (cam / rotor / injector)
Characteristics or malfunctioning
U000188
CAN Backbone bus 2 communication network
Bus Off
U001088
CAN Backbone bus 1 of the communication network
Bus Off
U008088
Communication Subnet of the car engine
Bus Off
U010100
Lost Communication With TECU
No subtype information
U010A00
Lost communication with the A module of the exhaust gas recirculation system
No subtype information
U010C00
The communication with the turbocharger / supercharger control module is broken
No subtype information
U012100
The communication with the anti-lock braking system (ABS)
No subtype information
U012900
Lost Communication With Brake Control Module
No subtype information
U014100
Lost connection with VMCU
No subtype information
U014200
Lost connection with the body control module «B»
No subtype information
U015500
Communication with the instrument cluster control module (IPC) is broken
No subtype information
U016700
Lost communication with the car immobilizer control module
No subtype information
U029D00
Communication with NOx sensor «A» is broken
No subtype information
U029E00
The communication with the NOx sensor «B» is broken
No subtype information
U032300
Software incompatibility with the dashboard control module
No subtype information
U033100
Incompatibility of software with the bodywork control module «A»
No subtype information
U042600
From the immobilizer control module of the car, unreliable data
No subtype information
U116600
Lost communication with CIOM
No subtype information
U116900
Lost connection with DACU
No subtype information
U116B00
Communication with TCM on the high-speed communication bus CAN
No subtype information
U116C00
Communication with TCM on the CAN bus of the power plant is broken
No subtype information
U116F00
Communication with the control module of the supply of the reducing agent via the engine subnetwork is broken
No subtype information
U117100
The communication with the control unit of the body equipment via the high-speed communication bus CAN
No subtype information
U117300
The communication with the IPC control unit via the high-speed communication CAN
No subtype information
U117888
CAN bus communication system bus
Bus Off
U1FFF68
Factory mode active
Event details
U300001
Electronic control module
General electrical fault
U300041
Electronic control module
Total checksum error
U300044
Electronic control module
Data memory failure
U300045
Electronic control module
Failure of program memory
U300049
Electronic control module
Internal failure of electronics
U300257
Vehicle Identification Number
Invalid / incompatible software component
Location Offline
Junior Member
Reputation:
5
Thanks Given: 22
Thanks Received: 14 (12 Posts)
Posts:
95
Threads:
20
Joined: Feb 2021
1
02-20-2021, 08:11 PM
hey guys i have over than 60 renault trucks which have same problem the engine rpm can’t go over 13 when i made a diagnostic it show me this code p228f-00
any solution ??
DAF & IVECO & Hino & maxxforce & cummins Tuning-programming-repairing-dealing with faults
PRS update files for new model of Daf trucks
Thanks given by:
naxnaxnax 
Location Offline
Senior Member
Reputation:
456
Thanks Given: 413
Thanks Received: 702 (75 Posts)
Posts:
226
Threads:
34
Joined: Jul 2013
2
02-20-2021, 09:44 PM
(This post was last modified: 02-20-2021, 09:46 PM by naxnaxnax.)
(02-20-2021, 08:11 PM)Moah008 Wrote: hey guys i have over than 60 renault trucks which have same problem the engine rpm can’t go over 13 when i made a diagnostic it show me this code p228f-00
any solution ??
EMS
P228F00
No information available.
No Sub Type Information
Engine derate
No information available.
Diagnostic Service 14. No additional action is needed.
Check:If fault not detected:Fault trace according to Tech Tool fault tree.
Fuel Pressure Regulator 1 Exceeded Learning Limits — Too High
Check injectors with TT.
Possible problem pressure sensor or valve on common rail pipe
Reputation:
86
Thanks Given: 87
Thanks Received: 121 (17 Posts)
Posts:
59
Threads:
11
Joined: Dec 2011
3
02-20-2021, 10:16 PM
(02-20-2021, 08:11 PM)Moah008 Wrote: hey guys i have over than 60 renault trucks which have same problem the engine rpm can’t go over 13 when i made a diagnostic it show me this code p228f-00
any solution ??
Hi.
I think you need to replace rail pressure sensor and harness to this sensor. Let me know what kind of engine you have? 11L or 13L then I can give you a parts number for both.
Thanks given by:
Moah008
Location Offline
Junior Member
Reputation:
5
Thanks Given: 22
Thanks Received: 14 (12 Posts)
Posts:
95
Threads:
20
Joined: Feb 2021
4
02-21-2021, 01:43 AM
(02-20-2021, 09:44 PM)naxnaxnax Wrote:
(02-20-2021, 08:11 PM)Moah008 Wrote: hey guys i have over than 60 renault trucks which have same problem the engine rpm can’t go over 13 when i made a diagnostic it show me this code p228f-00
any solution ??EMS
P228F00
No information available.
No Sub Type Information
Engine derate
No information available.
Diagnostic Service 14. No additional action is needed.
Check:If fault not detected:Fault trace according to Tech Tool fault tree.
Fuel Pressure Regulator 1 Exceeded Learning Limits — Too HighCheck injectors with TT.
Possible problem pressure sensor or valve on common rail pipe
We already change the pressure sensor and the fault still available
What u mean by TT ?
Attached Files
Thumbnail(s)
DAF & IVECO & Hino & maxxforce & cummins Tuning-programming-repairing-dealing with faults
PRS update files for new model of Daf trucks
Thanks given by:
naxnaxnax
Location Offline
Senior Member
Reputation:
456
Thanks Given: 413
Thanks Received: 702 (75 Posts)
Posts:
226
Threads:
34
Joined: Jul 2013
5
02-21-2021, 04:56 AM
(02-21-2021, 01:43 AM)Moah008 Wrote:
(02-20-2021, 09:44 PM)naxnaxnax Wrote:
(02-20-2021, 08:11 PM)Moah008 Wrote: hey guys i have over than 60 renault trucks which have same problem the engine rpm can’t go over 13 when i made a diagnostic it show me this code p228f-00
any solution ??EMS
P228F00
No information available.
No Sub Type Information
Engine derate
No information available.
Diagnostic Service 14. No additional action is needed.
Check:If fault not detected:Fault trace according to Tech Tool fault tree.
Fuel Pressure Regulator 1 Exceeded Learning Limits — Too HighCheck injectors with TT.
Possible problem pressure sensor or valve on common rail pipeWe already change the pressure sensor and the fault still available
What u mean by TT ?
Test 23753-3 Common rail fuel system in Techtool (TT).
Thanks given by:
Moah008
Location Offline
Junior Member
Reputation:
5
Thanks Given: 22
Thanks Received: 14 (12 Posts)
Posts:
95
Threads:
20
Joined: Feb 2021
6
02-21-2021, 02:13 PM
(02-20-2021, 10:16 PM)kenezzz Wrote:
(02-20-2021, 08:11 PM)Moah008 Wrote: hey guys i have over than 60 renault trucks which have same problem the engine rpm can’t go over 13 when i made a diagnostic it show me this code p228f-00
any solution ??Hi.
I think you need to replace rail pressure sensor and harness to this sensor. Let me know what kind of engine you have? 11L or 13L then I can give you a parts number for both.
injectors test attached ..
Attached Files
Thumbnail(s)
DAF & IVECO & Hino & maxxforce & cummins Tuning-programming-repairing-dealing with faults
PRS update files for new model of Daf trucks
Thanks given by:
naxnaxnax
Location Offline
Senior Member
Reputation:
456
Thanks Given: 413
Thanks Received: 702 (75 Posts)
Posts:
226
Threads:
34
Joined: Jul 2013
7
02-21-2021, 07:47 PM
(02-21-2021, 02:13 PM)Moah008 Wrote:
(02-20-2021, 10:16 PM)kenezzz Wrote:
(02-20-2021, 08:11 PM)Moah008 Wrote: hey guys i have over than 60 renault trucks which have same problem the engine rpm can’t go over 13 when i made a diagnostic it show me this code p228f-00
any solution ??Hi.
I think you need to replace rail pressure sensor and harness to this sensor. Let me know what kind of engine you have? 11L or 13L then I can give you a parts number for both.injectors test attached ..
Let’s go slowly, is it a Renault common rail system or a injector?
This in the picture is the cylinder balancing. In tab Test under group 23 find test «common rail system…» then test it. Or find someone who has used Techtool a little longer.
BR
Thanks given by:
Reputation:
8
Thanks Given: 299
Thanks Received: 98 (54 Posts)
Posts:
327
Threads:
116
Joined: Dec 2017
8
04-21-2022, 07:23 PM
Dealer now supplying update flash and remove rail pressure regulator but my truck still setting this code
Any Ktag dimsport expert fixes for this terrible problem? Thanks
Thanks given by:
Reputation:
0
Thanks Given: 34
Thanks Received: 8 (5 Posts)
Posts:
32
Threads:
7
Joined: Mar 2015
9
04-22-2022, 06:55 AM
This fault doesn’t mean you need to replace the pressure sensor it means the fuel pressure regulator is having to work overtime to maintain fuel pressure in the rail so you either have a leak ie pressure relief valve or injector leak off or you could have an issue creating the pressure in the 1st place ie 1 of the pump unit injectors not contributing due to being worn or a spun cam lobe for the pump unit injectors.
There is a good case study covering this fault on PicoAuto and is very easy to diagnose accurately especially if you have a scope.
Расшифровка кодов диагностики OBDII/EOBD
Если ваш автомобиль поддерживает OBD2 или EOBD, то вы уже можете искать среди 5000 описаний кодов, являющихся стандартными для всех производителей. Это коды следующих серий: P0XXX, P2XXX, P34XX, B0XXX, C0XXX, U0XXX, U2XXX, U3XXX.
Также доступны более 13500 дополнительных кодов, специфичных для конкретных производителей.
Выберите код:
Generic (Общее для всех автопроизводителей):
Fuel Pressure Regulator 1 Exceeded Learning Limits — Too High (Регулятор давления топлива 1, превышение лимита адаптации — слишком высокий уровень сигнала
)