Pilz pss 3047 3 ошибки - Не ошибается лишь тот, кто ничего не делает!

Modular Block System: Emergency Stop Circuits

6-25

The acknowledgements

FbL1 and FbL2 are also monitored in the static

condition. If there are discrepancies between the set and true condition, an
error message will be issued (

ENBL = 0) and the contactors will be

switched off immediately (

K1 = 0 and K2 = 0). The error will need to be

reset.

It is possible to reset errors via the input parameter

RSET both when ON =

0 and when

ON = 1. However, a prerequisite for setting the enable and,

when

ON = 1, switching on the contactors, is that the signals from the

feedback loops are correct.

Error messages

Any fault that is detected will be stored in the corresponding error data
word (

SSNR) of the administration data block (1st data block), until the

fault has been fully dealt with.

• Error messages in the administration data block

— Bit 00:

Fault as the signal changes at input parameter

ON,

feedback loop 1 (

FbL1) remains open

Remedy: Check contactor, contacts, cable, input card, output
card, value of input parameter

TFbL and all conditions and

then reset (input parameter

RSET)

— Bit 01:

Fault as the signal changes at input parameter

ON,

feedback loop 1 (

FbL1) remains closed

Remedy: Check contactor, contacts, cable, input card, output
card, value of input parameter

TFbL and all conditions and

then reset (input parameter

RSET)

— Bit 02:

Fault as the signal changes at input parameter

ON,

feedback loop 2 (

FbL2) remains open

Remedy: Check contactor, contacts, cable, input card, output
card, value of input parameter

TFbL and all conditions and

then reset (input parameter

RSET)

Источник

List of Pilz PSS Series Guides:

Guidesimo.com webproject is not a service center of Pilz trademark and does not carries out works for diagnosis and repair of faulty Pilz PSS Series equipment. For quality services, please contact an official service center of Pilz company. On our website you can read and download documentation for your Pilz PSS Series device for free and familiarize yourself with the technical specifications of device.

More Adapter Devices:

Paradyne 6512

TSTLINEALMPWRETHERNETTMTM98-16014a-01TM 1SuperLine AdapterInstallation InstructionsDocument Number 6512-A2-GN10-20January 1999SuperLineAdapterContents: Important Safety Instructions What Your SuperLine Adapter Does Package Checklist Optional Hardware (Not Supplied) Front Panel Indicators SuperLine Adapter Rear Panel Installing Your SuperLine Adapter Troubleshooting Yo …

6512 Adapter, 28
Linksys WPC54G

F. The Setup Wizard will askyou to review your settingsbefore it starts to copy files.Click Next if you are satis-fied with your settings, orclick Back to change anysettings. G. After the files have beensuccessfully copied, youwill see Figure G. Click theExit button.Proceed to Step 2.WPC54GPackage Contents• One Wireless-G Notebook Adapter (1)• One Setup Wizard CD-ROM with UserGuide (2)• On …

WPC54G Adapter, 2
Mini Gadgets LMWiFiPower

Updated 06/30/2016 1 Version 1.0 POWER ADAPTER WITH HIDDEN CAMERA SKU: LMWiFiPower THANK YOU FOR PURCHASING THE LMWIFIPOWER Please read this manual before operating the LMWiFiPower and keep it handy. The most ubiquitous, unnoticeable devices nowadays are chargers. With the average Joe carrying at least two or three rechargeable electronic devices on their person every da …

LMWiFiPower Adapter, 5
D-Link DFE-530TX

Contents of Package: • DFE-530TX+ Ethernet PCI Adapter • Printed Quick Installation Guide • CD with Manual and Drivers If any of the above items are missing, please contact your reseller. Before you start, make sure to turn off your computer and unplug the power cord. Note: To avoid damage caused by static electricity, make sure to properly ground yourself by first touching a metal par …

DFE-530TX Adapter, 6

List of Pilz PSS Series Guides:

More Adapter Devices:

Recommended Documentation: