-
Игорь Кедровский
- Участник
- Сообщения: 55
- Зарегистрирован: 24 мар 2015 13:00
- Последний визит: 02 июн 2023 22:16
- Изменить репутацию:
Репутация: нет - Откуда: Ричмонд
Service call 0109 Wiper system Roland 645EX.
Всем привет!Надеюсь на вашу помошь, ситуация очень неприятная.
После замены трубопроводов (лопнула одна трубка посредине, немного позаливало неопасно)и сборки принетра,
машина выдала ошибку вайперов 0109.
1/ заменены 2 датчика
2. заменены 2 мотора (взял от моторы от пом, они такие же)
3. станция была демонтирована и полностью отмыта, смазана (и расцелована с бубном.)
Что происходит?
— после включения машины вайпера начинают двигаться, проходят 4-5 см и останавливаются. ПИПИК. ОШИБКА.0109
Выкл.вкл.
-вайпера снова двигаются. проходят еще 4-5 см и оснанавливаются. снова ошибка.
Соверщенно не понимаю. Можно ли откалибровать станцию, если это имеет смысл. (инженерное меню?)
Я заказл провод сенсоров, но непонятно, когда приедет.
Заранее благодарен. не понимаю, что делать, надеюсь !!!как всегда!!! на помошь сообшества.
Хорошего всем дня!
-
Андрей Колыхалов
- ЗЕНОН-ТЕХНИК
- Сообщения: 5
- Зарегистрирован: 28 окт 2020 10:36
- Последний визит: 02 июн 2023 12:25
- Изменить репутацию:
Репутация:
Голосов: 1 - Откуда: Волгоград
Re: Service call 0109 Wiper system Roland 645EX.
Сообщение Андрей Колыхалов » 18 май 2023 09:01
-
plotterhell
- Старожил
- Сообщения: 1197
- Зарегистрирован: 06 фев 2017 10:15
- Последний визит: 04 июн 2023 12:44
- Изменить репутацию:
Репутация:
Голосов: 15 - Откуда: Москва
Re: Service call 0109 Wiper system Roland 645EX.
Сообщение plotterhell » 18 май 2023 10:03
Совершенно бесполезная ссылка. Речь о про2. Там нет револьвера. Смазывать направляющие не стоило — это может быть причиной, как бы странно это не звучала заклинивания. Войти в сервис и проверить показания датчиков каретки вайперов. А перед этим всем себя проверить вы провода для датчиков местами не напутали?
Иц май лайф! Хэппинейшан! Камон, чекераут!
Ребята, ищите контакты где-то в интернетах.
plotterhelp
-
Игорь Кедровский
- Участник
- Сообщения: 55
- Зарегистрирован: 24 мар 2015 13:00
- Последний визит: 02 июн 2023 22:16
- Изменить репутацию:
Репутация: нет - Откуда: Ричмонд
Re: Service call 0109 Wiper system Roland 645EX.
Сообщение Игорь Кедровский » 18 май 2023 13:55
из Сервис меню — проверка cap/wiper відала сообщение «Unrecoverable cap» ну и 0109 конечно.
Хорошего всем дня!
-
Legus
- Завсегдатай
- Сообщения: 585
- Зарегистрирован: 12 авг 2015 09:13
- Последний визит: 04 июн 2023 10:11
- Изменить репутацию:
Репутация:
Голосов: 16 - Откуда: Тольятти
Re: Service call 0109 Wiper system Roland 645EX.
Сообщение Legus » 18 май 2023 15:58
Краской не залили какой нибудь оптический датчик?
-
Игорь Кедровский
- Участник
- Сообщения: 55
- Зарегистрирован: 24 мар 2015 13:00
- Последний визит: 02 июн 2023 22:16
- Изменить репутацию:
Репутация: нет - Откуда: Ричмонд
Re: Service call 0109 Wiper system Roland 645EX.
Сообщение Игорь Кедровский » 18 май 2023 17:26
wioer system/ Все вымыто до блеска.
На всяий случай Я заказал кабель, но ждять придется 3 недели.
Из рекомендаций
1. Проверить 2 датчика .ЗАМЕНЕНЫ.
2. Проверить двигатели. ЗАМЕНЕНЫ оба.
3. Помыть — ПОМЫТО.
4. Проверить кабель датчиков. ЖДЕМ. А пока попробую прозвонить.
????
Отправлено спустя 26 минут 43 секунды:
у Digiprint supply кабелей нет вообще. — месяц ждать.
Закзал в Италии, через три дня сообщу.
Хорошего всем дня!
-
mks.mpei
- Старожил
- Сообщения: 1184
- Зарегистрирован: 21 май 2016 18:12
- Последний визит: 04 июн 2023 11:27
- Изменить репутацию:
Репутация:
Голосов: 21 - Откуда: Москва
Re: Service call 0109 Wiper system Roland 645EX.
Сообщение mks.mpei » 18 май 2023 19:33
Игорь Кедровский писал(а): (→)Из рекомендаций
а как же рекомендация выкинуть и купить новый роланд?)
-
plotterhell
- Старожил
- Сообщения: 1197
- Зарегистрирован: 06 фев 2017 10:15
- Последний визит: 04 июн 2023 12:44
- Изменить репутацию:
Репутация:
Голосов: 15 - Откуда: Москва
Re: Service call 0109 Wiper system Roland 645EX.
Сообщение plotterhell » 22 май 2023 11:29
Если неудачно залить разъёмы — сгорает серво боард. Разбирайтесь.
Иц май лайф! Хэппинейшан! Камон, чекераут!
Ребята, ищите контакты где-то в интернетах.
plotterhelp
-
Фрезеровщиk
- Завсегдатай
- Сообщения: 518
- Зарегистрирован: 22 сен 2018 02:26
- Последний визит: 02 июн 2023 08:31
- Изменить репутацию:
Репутация:
Голосов: 9 - Откуда: Находка
Re: Service call 0109 Wiper system Roland 645EX.
Сообщение Фрезеровщиk » 22 май 2023 14:48
Какой шлейф, какой борд? У меня есть запчасти от этого принтера. Сфотографируйте.
-
Игорь Кедровский
- Участник
- Сообщения: 55
- Зарегистрирован: 24 мар 2015 13:00
- Последний визит: 02 июн 2023 22:16
- Изменить репутацию:
Репутация: нет - Откуда: Ричмонд
Re: Service call 0109 Wiper system Roland 645EX.
Сообщение Игорь Кедровский » 23 май 2023 22:14
Хорошего всем дня!
-
Фрезеровщиk
- Завсегдатай
- Сообщения: 518
- Зарегистрирован: 22 сен 2018 02:26
- Последний визит: 02 июн 2023 08:31
- Изменить репутацию:
Репутация:
Голосов: 9 - Откуда: Находка
Re: Service call 0109 Wiper system Roland 645EX.
Сообщение Фрезеровщиk » 24 май 2023 01:11
Вы в Пендосии?
ссылка не работает, можно просто фото?
-
Игорь Кедровский
- Участник
- Сообщения: 55
- Зарегистрирован: 24 мар 2015 13:00
- Последний визит: 02 июн 2023 22:16
- Изменить репутацию:
Репутация: нет - Откуда: Ричмонд
Re: Service call 0109 Wiper system Roland 645EX.
Сообщение Игорь Кедровский » 02 июн 2023 03:16
К сожалению не могу разместить фот и видео. (Да ,я в США сейчас). Если дадаите совет, воспользуюсь с благодарностью.
Итоги 3-х недель.
Заменены двигатели, датчики, новый кабель датчиков. (Есть даже новая плата серво, но пока не решился ставить).
После вколючения вигатели начинают рабоатть, происходит некое движение вайперов и остановка
!! сообщение 0109…Проверил все какбеля, вроде ничего не висит.
ДАЖЕ!!! При отключении датачиков, двигатели начинают работать, и останавливаются.
проосто не понимаю, как решить проблему.
Звонить в сервис Roland — не проблема, но у меня есть сомнения в их компетенции. (по поводу 645 как минимум, модель старая…)
Плату менчять будем? Вся надежда на сообщество…
И подскажите общедоступній сервер, куда можнло залить видео и фото, пожалуйста…
Хорошего всем дня!
-
Фрезеровщиk
- Завсегдатай
- Сообщения: 518
- Зарегистрирован: 22 сен 2018 02:26
- Последний визит: 02 июн 2023 08:31
- Изменить репутацию:
Репутация:
Голосов: 9 - Откуда: Находка
Re: Service call 0109 Wiper system Roland 645EX.
Сообщение Фрезеровщиk » 02 июн 2023 06:52
Оно?
пару раз выпадал в ошибку, когда засохшие чернила тормозили движение по направляющей. А так, даже в таком состоянии все работало. Может вы не там ищете?
- Вложения
-
-
- EFDAFE40-2A3D-4A03-AD1B-6FB1A5A48028.jpeg (303.14 КБ) 71 просмотр
-
-
-
- 7D3CB66E-34B3-4F7C-8DE1-723AA907B771.jpeg (326.63 КБ) 74 просмотра
-
-
-
- 592F5DE7-2101-4D09-827A-0067300CED44.jpeg (376.67 КБ) 74 просмотра
-
Последний раз редактировалось Фрезеровщиk 02 июн 2023 06:59, всего редактировалось 3 раза.
-
Игорь Кедровский
- Участник
- Сообщения: 55
- Зарегистрирован: 24 мар 2015 13:00
- Последний визит: 02 июн 2023 22:16
- Изменить репутацию:
Репутация: нет - Откуда: Ричмонд
Re: Service call 0109 Wiper system Roland 645EX.
Сообщение Игорь Кедровский » 02 июн 2023 11:41
Спасибо. Вторая фотография — это весь узел вайперов. это оно. только у меня он уже полностью отмыт… попробую поменячть срвис борд.
НО. после вклбчения двигатели начинают движени 2 секуунды и потом останавливаются. оба. тоесть узел реагирует. если бы сгорело, то думаю, просто нисего бы не происходило…,
Может быть заново разобрать и промыть направляющие?
Отправлено спустя 2 минуты 2 секунды:
иными словами -это электорника или механика?
Хорошего всем дня!
-
mks.mpei
- Старожил
- Сообщения: 1184
- Зарегистрирован: 21 май 2016 18:12
- Последний визит: 04 июн 2023 11:27
- Изменить репутацию:
Репутация:
Голосов: 21 - Откуда: Москва
Re: Service call 0109 Wiper system Roland 645EX.
Сообщение mks.mpei » 02 июн 2023 12:22
Игорь Кедровский писал(а): (→)И подскажите общедоступній сервер, куда можнло залить видео и фото, пожалуйста…
drive.google.com
Вернуться в «Принтеры ROLAND»
Кто сейчас на конференции
Сейчас этот форум просматривают: нет зарегистрированных пользователей и 0 гостей
Support Home
Warranty Registration
Email Support
User Forums
Knowledge Base Article
VersaArt RS-640 64″ Eco-Solvent Inkjet Printer
Title
Service Call 0109
Summary
Service Call 0109
Details
Symptom
Service Call 0109.
Cause
Roland devices have multiple failsafe mechanisms to protect critical components. The machine will stop operations when any of these failsafes are triggered.
Solution
Wiper protection error, turn the printer’s power off and then back on. If the error continues, record the error and contact your local Roland Service Center.
Modified
May 13, 2020
-
said
- Новичок
- Сообщения: 6
- Зарегистрирован: 12 дек 2016 09:59
- Последний визит: 06 июн 2022 11:32
- Изменить репутацию:
Репутация: нет - Откуда: Baku
Roland VP540i, call service 0109
Здравствуйте.
принтер выдает ошибку CALL SARVICE 0109, при включении каретка слегка отодвигается налево и остаанвливается.
Кто либо сталкивался с подобной проблемой?
-
plotterhelp
- Старожил
- Сообщения: 2227
- Зарегистрирован: 13 июн 2013 06:02
- Последний визит: 26 янв 2020 14:26
- Изменить репутацию:
Репутация:
Голосов: 66 - Откуда: Москва
Сообщение plotterhelp » 13 дек 2016 00:39
Если не ошибаюсь, то рпоблема с вайпером, его мотором или датчиком.
Никакой рекламы в подписи!
Вернуться в «Принтеры ROLAND»
Кто сейчас на конференции
Сейчас этот форум просматривают: нет зарегистрированных пользователей и 0 гостей
Support Home
Warranty Registration
Email Support
User Forums
Knowledge Base Article
VersaArt RS-640 64″ Eco-Solvent Inkjet Printer
Summary
Service Call 0109
Details
Symptom
Service Call 0109.
Cause
Roland devices have multiple failsafe mechanisms to protect critical components. The machine will stop operations when any of these failsafes are triggered.
Solution
Wiper protection error, turn the printer’s power off and then back on. If the error continues, record the error and contact your local Roland Service Center.
-
#1
Hi, I have a VP-540i that is giving me problems. I am getting an error 0109 error. I have the service manual and tried replacing the wiper motor and sensor. The motor does not even try to rotate. If i go to service mode i can see the sensor works if I push the wiper to and away from home position.
My next guess would be the servo board. does anyone have any suggestions for me? is there a way to try to start or move the motor in service mode manually? is there a chance that the servo board could be bad or blown a fuse?
Your help will be appreciated. Thank you
Last edited: May 19, 2017
-
#5
Hey cwaldner,
Considering the wiper sensor is working, the motor does not rotate, and the cable connection to the servo board seem to check out, what remains is a failed wiper motor (albeit new) and/or failed servo board. Beyond this consideration, it’s recommended to consult with your regional Roland dealer for parts and repair.
If you have additional questions or need extra support directly from Roland corporate support, please submit an «official» support request form online here: Product Support Form | Roland
If you do write us, we look forward to helping you and take care,
Roland Technical Support
Roland DGA Corp.
rn
CHECKING
NO
POINT
Service Call
1
2
Internal Error
6-14 SERVICE CALL
CODE
MEANING
No.
0002
Sub CPU
Disorder of communication with
Communication
Sub CPU
Error
0003
DIPSW model
A setup about the model of DIPSW
setting error
is set up in an unsuitable
combination.
0101
Limit Position
Limit Position Initialize has not
Error
been done.
0102
Head Lock
Even though the machine carries
Sensor Error
out the regular movement, the
output of the Head Lock Sensor
does not reach the expected value.
0103
Limit Sensor
Even though the machine carries
Error
out the regular movement, the
output of the Limit Sensor does not
reach the expected value.
0104
Cap Unit
Even though the machine carries
Protection Error
out the regular movement, the
output of Cap Sensor does not
reach the expected value.
0105
Tool Carriage
Machine fails to connect the Tool
Connection
Carriage to the Head Carriage.
Error
0106
Tool Carriage
Machine fails to disconnect the
Disconnection
Tool Carriage from the Head
Error
Carriage.
0107
Unset up of the
Linear Encoder Setup has not
Linear Encoder
been done.
0109
Wiper
Even though the machine carries
Protection Error
out the regular movement, the
output of the Wiper Origin Sensor
does not reach the expected value.
0110
Linear Encoder
Input value from Linear Encoder is
Error
not changed when Linear Encoder
is set up the Origin.
When Motor stops during printing,
Motor does not complete the
movement which is supposed to be
done.
ACTION
Refer to Service Call
Restart machine
CONTENTS
REFERENCE
Refer to Service Call
This message is displayed when an unexpected error happens.
In the most case, the error can be fixed by restarting the machine.
If the error still happens in spite of restarting the machine, it
sometimes could be solved by carrying out the Limit Initialization
or changing some setting values.
CAUSE
Sub Board does not work correctly.
Sub CPU does not work correctly.
There is a bad connection between
Main Board and Sub Board.
DIPSW setup error
DIPSW defect
Main Board defect
Limit Position Initialize has not been
done.
Head Lock Sensor does not work
correctly or is broken.
Limit Sensor does not work correctly or
is broken.
Disorder of Cap Motor
Fault of Cap Unit
Fault of Cap Sensor
Cut-line or short-circuit of Cable and
Flexible Cable
Fault of Tool Carriage Connection
Loose of Connection Part
Fault of the Limit Position Initialize value
Limit Sensor does not work correctly or
is broken.
Disorder of Cap Motor
Loose of Connection Part
Fault of the Limit Position Initialize value
Limit Sensor does not work correctly or
is broken.
Linear Encoder Setup has not been
done.
Disorder of Wiper Origin Sensor
Fault of Wiper Unit
Fault of Wiper Origin Sensor
Cut-line or short-circuit of Cable and
Flexible Cable
Read error of Linear Encoder
Read error of Encoder on Scan Motor
side
Wire is not fixed to Head Carriage firmly.
6-10
OUTLINE
ACTION
1) Check Cable Connection between Main Board
and Servo Board
2) Servo Board Replacement
3) Main Board Replacement
1) Check the DIPSW setup
2) Replacement the Main Board
1) Carry out Limit Position Initialize.
1) Head Lock Sensor Replacement
2) Check the mechanical Backlash or loose with
the scanning axes.
1) Limit Sensor Replacement
2) Check the mechanical Backlash or loose with
the scanning axes.
1) Cap Motor Replacement
2) Cap Unit Replacement
3) Cap Sensor Replacement
4) Cable and Flexible Cable Replacement
1) Check the mechanical Backlash or loose with
the Tool Carriage part.
2) Lock Position Adjustment
3) Limit Position and Cut Down Position Initialize
4) Limit Sensor Replacement
1) Check the mechanical Backlash or loose with
the Tool Carriage part.
2) Lock Position Adjustment
3) Limit Position and Cut Down Position Initialize
4) Limit Sensor Replacement
1) Carry out Linear Encoder Setup.
1) Wiper Origin Motor Replacement
2) Wiper Unit Replacement
3) Wiper Origin Sensor Replacement
4) Cable and Flexible Cable Replacement
1) Confirm whether Encoder Scale is between the
slit of Encoder Module in a whole width of the
machine.
2) Linear Encoder Replacement
3) Scan Motor Replacement
4) Confirm Cable Connection between Linear
Encoder Board and Print Carriage Board.
5) Confirm Connection between Wire and Head
Carriage.
-
#1
Hi, I have a VP-540i that is giving me problems. I am getting an error 0109 error. I have the service manual and tried replacing the wiper motor and sensor. The motor does not even try to rotate. If i go to service mode i can see the sensor works if I push the wiper to and away from home position.
My next guess would be the servo board. does anyone have any suggestions for me? is there a way to try to start or move the motor in service mode manually? is there a chance that the servo board could be bad or blown a fuse?
Your help will be appreciated. Thank you
Last edited: May 19, 2017
-
#5
Hey cwaldner,
Considering the wiper sensor is working, the motor does not rotate, and the cable connection to the servo board seem to check out, what remains is a failed wiper motor (albeit new) and/or failed servo board. Beyond this consideration, it’s recommended to consult with your regional Roland dealer for parts and repair.
If you have additional questions or need extra support directly from Roland corporate support, please submit an «official» support request form online here: Product Support Form | Roland
If you do write us, we look forward to helping you and take care,
Roland Technical Support
Roland DGA Corp.
rn
CHECKING
NO
POINT
Service Call
1
2
Internal Error
6-14 SERVICE CALL
CODE
MEANING
No.
0002
Sub CPU
Disorder of communication with
Communication
Sub CPU
Error
0003
DIPSW model
A setup about the model of DIPSW
setting error
is set up in an unsuitable
combination.
0101
Limit Position
Limit Position Initialize has not
Error
been done.
0102
Head Lock
Even though the machine carries
Sensor Error
out the regular movement, the
output of the Head Lock Sensor
does not reach the expected value.
0103
Limit Sensor
Even though the machine carries
Error
out the regular movement, the
output of the Limit Sensor does not
reach the expected value.
0104
Cap Unit
Even though the machine carries
Protection Error
out the regular movement, the
output of Cap Sensor does not
reach the expected value.
0105
Tool Carriage
Machine fails to connect the Tool
Connection
Carriage to the Head Carriage.
Error
0106
Tool Carriage
Machine fails to disconnect the
Disconnection
Tool Carriage from the Head
Error
Carriage.
0107
Unset up of the
Linear Encoder Setup has not
Linear Encoder
been done.
0109
Wiper
Even though the machine carries
Protection Error
out the regular movement, the
output of the Wiper Origin Sensor
does not reach the expected value.
0110
Linear Encoder
Input value from Linear Encoder is
Error
not changed when Linear Encoder
is set up the Origin.
When Motor stops during printing,
Motor does not complete the
movement which is supposed to be
done.
ACTION
Refer to Service Call
Restart machine
CONTENTS
REFERENCE
Refer to Service Call
This message is displayed when an unexpected error happens.
In the most case, the error can be fixed by restarting the machine.
If the error still happens in spite of restarting the machine, it
sometimes could be solved by carrying out the Limit Initialization
or changing some setting values.
CAUSE
Sub Board does not work correctly.
Sub CPU does not work correctly.
There is a bad connection between
Main Board and Sub Board.
DIPSW setup error
DIPSW defect
Main Board defect
Limit Position Initialize has not been
done.
Head Lock Sensor does not work
correctly or is broken.
Limit Sensor does not work correctly or
is broken.
Disorder of Cap Motor
Fault of Cap Unit
Fault of Cap Sensor
Cut-line or short-circuit of Cable and
Flexible Cable
Fault of Tool Carriage Connection
Loose of Connection Part
Fault of the Limit Position Initialize value
Limit Sensor does not work correctly or
is broken.
Disorder of Cap Motor
Loose of Connection Part
Fault of the Limit Position Initialize value
Limit Sensor does not work correctly or
is broken.
Linear Encoder Setup has not been
done.
Disorder of Wiper Origin Sensor
Fault of Wiper Unit
Fault of Wiper Origin Sensor
Cut-line or short-circuit of Cable and
Flexible Cable
Read error of Linear Encoder
Read error of Encoder on Scan Motor
side
Wire is not fixed to Head Carriage firmly.
6-10
OUTLINE
ACTION
1) Check Cable Connection between Main Board
and Servo Board
2) Servo Board Replacement
3) Main Board Replacement
1) Check the DIPSW setup
2) Replacement the Main Board
1) Carry out Limit Position Initialize.
1) Head Lock Sensor Replacement
2) Check the mechanical Backlash or loose with
the scanning axes.
1) Limit Sensor Replacement
2) Check the mechanical Backlash or loose with
the scanning axes.
1) Cap Motor Replacement
2) Cap Unit Replacement
3) Cap Sensor Replacement
4) Cable and Flexible Cable Replacement
1) Check the mechanical Backlash or loose with
the Tool Carriage part.
2) Lock Position Adjustment
3) Limit Position and Cut Down Position Initialize
4) Limit Sensor Replacement
1) Check the mechanical Backlash or loose with
the Tool Carriage part.
2) Lock Position Adjustment
3) Limit Position and Cut Down Position Initialize
4) Limit Sensor Replacement
1) Carry out Linear Encoder Setup.
1) Wiper Origin Motor Replacement
2) Wiper Unit Replacement
3) Wiper Origin Sensor Replacement
4) Cable and Flexible Cable Replacement
1) Confirm whether Encoder Scale is between the
slit of Encoder Module in a whole width of the
machine.
2) Linear Encoder Replacement
3) Scan Motor Replacement
4) Confirm Cable Connection between Linear
Encoder Board and Print Carriage Board.
5) Confirm Connection between Wire and Head
Carriage.