Sinumerik Alarm 25080 Axis %1 positioning monitoring
Parameters:
%1 = Axis name, spindle number
Definitions:
For blocks in which “exact stop” is effective, the axis must have reached the exact stop window after the positioning time given in the axis-specific MD 36020 POSITIONING_TIME. Exact stop coarse: MD 36000 STOP_LIMIT_COARSE Exact stop fine: MD 36010 STOP_LIMIT_FINE The alarm can be reprogrammed in the MD ALARM_REACTION_CHAN_NOREADY (channel not ready).
Reactions:
– Mode group not ready.
– Channel not ready.
– If the axis is a single axis when this alarm is triggered, the alarm is only effective for this axis (not effective for e.g. the channel or mode group)
– Channel not ready.
– NC Start disable in this channel.
– NC Stop on alarm.
– The NC switches to follow-up mode.
– Alarm display.
– Interface signals are set.
Remedy:
Please inform the authorized personnel/service department. Check whether the exact stop limits (course and fine) correspond to the dynamic possibilities of the axis, otherwise increase them, if necessary in connection with the positioning time set in MD 36020 POSITIONING_TIME. Check speed controller/position controller optimization; select highest possible gains. Check setting of Kv factor (MD 32200 POSCTRL_GAIN) and increase if necessary.
Program Continuation:
Clear alarm with the RESET key in all channels of this mode group. Restart part program.
References
- Siemens Diagnostics Guide by Siemens
Sinumerik Alarm 25080 Axis %1 positioning monitoring
Доброе время суток! Токарный станок китаец ck6150, энкодер Aton Technologies, ловит периодически ошибки 25040 и 25080 при позиционировании шпинделя через SPOSA. Т.е он отрабатывает иногда как положено, а иногда уходит в ошибку, регулировал параметры по данной ошибке, стало лучше вроде бы, но все же периодически ошибки ловит. При этом на патроне маркером отметил точки 0°, 180°, 200°, станок по ним отрабатывает ровно несколько раз до появления ошибки, после сброса ошибки по точкам отмечается смещение. Работает по этому смещению так же до появления ошибки и далее, после ошибки опять смещает и отрабатывает с новым смещением.
- Цитата
- 30 Июл 2009
Теперь что означают светодиоды.
1.Зеленые,-«POK»-POWER OK» ,»PR»-POWER READY
2.Красные,-«NF»-NCK FAULT(ошибка системы),»CF»-COMMUNICATION FAULT(ошибка связи),»PS»-PLC STOP(останов PLC),»PF»-PLC FAULT(ошибка PLC)
3.Желтые,»CB»-COMMUNICATION BOOT FILES FOR SIMODRIVE-611D,
«CP»-COMMUNICATION PROCESSOR,»PFO»-PLC IN FIRST OUT,»DP»,-DUAL PORT.
Для чего нужны кнопки,»NMI»-NUMERICAL MACHINE INTERFACE-используется для активации диагностического интерфейса в процессе работы с программой «LADDER»,»RESET»,-ручной сброс и перезапуск NCK контроллера.
Добавлено 30-07-2009 22:58
Маленькая тонкость в названии «NCK»,это не NUMERICAL CONTROL KEMEL,a KERNEL!
Добавлено 30-07-2009 23:05
Т.е. по русски KERNEL,-это ядро.C «верблюдом» связи никакой нету!
Добавлено 30-07-2009 23:16
Многие называют «NCK»- ядром системы,я считаю, что это определение несколько узковато,т.к. понятие NCK и функциональное значение намного шире.
Добавлено 30-07-2009 23:29
Ах да,забыл совсем!Что такое за переключатель не коннекторе интерфейса.Значит,это интерфейс «PROFIBUS-DP»,а переключатель «MASTER/SLAVE» и все дела.
- 31 Июл 2009
andreieinav сказал(а):
Ах да,забыл совсем!Что такое за переключатель не коннекторе интерфейса.Значит,это интерфейс «PROFIBUS-DP»,а переключатель «MASTER/SLAVE» и все дела.
Чуть поправлю, переключатель терминирования линии, подкл. к линии реэюк 120 ОМ, при неподключенном к устройству разъеме.
- 31 Июл 2009
o_l_e_g,согласен-это один из вариантов «заглушки»
- 31 Июл 2009
Доброго времени суток! С большим удовольствием прочитал эту тему, очень хорошо все описано. Хотелось бы попросить поподробней описать процедуру восстановления 840 Семена PCU-20, при наличии резервных файлов на карте памяти. К сожалению, сейчас не на работе, но после слета данных обнаружил на карте памяти два файла- что-то типа NCU-PLC и PLC. Хотелось бы узнать положения кодовых переключателей S3, S4 и последовательность ввода в эксплуатацию. И ещё такой вопрос- чем определяется уровень доступа при включении станка? У нас 2 стойки при включении находятся сразу с правами производителя, можно ли это каким-либо образом исправить? По поводу программы для закачки и выгрузки файлов в стойку (не только в семены) используем бесплатную программу NC-Link Free, под хрюшей и с преобразователем USB-Com работает без проблем. Интерфэйс у нее правда английский, но все понятно, есть возможность сохранять комовские настройки для разных типов стоек. Заранее благодарен!
- 31 Июл 2009
Уважаемый Andreieinav подскажите пожалуйста sinumerik 810D у нас происходит биение оси «Y» выдает ошибки (25080 и 25030) контроль позиционирования и аварийный предел фактической скорости. Пробовали в MD уменьшать скорость, контроль над скоростью md 36200 ставили на 10% больше максимальной в документации советуют правильно определить коэффициент Kv в общем запутались мы окончательно помогите пожалуйста!
- 1 Авг 2009
martyn_80, перекинь измерительный кабель с другой оси, заведомо исправный.
- 1 Авг 2009
В случаях, как у Martiyn_80, мы обычно поступали следующим образом- неисправность похожа на обрыв обратной связи, и тут важно каким образом позиционируется ось, энкодерами двигателя или есть дополнительные оптические линейки, и проявляется ли неисправность в ручном режиме станка. Перебрасывали оси местами, правда у нас в основном токарки, X c Z, перемещали маховичком оси и определяли, действительно ли обрыв обратной связи, либо неисправен привод, либо механика. В случае с оптическими линейками несколько сложнее, но неисправность чисто внешне выглядит не так.
- 2 Авг 2009
Значит,начну с Martyn_80.
Если машина вывесила транспорант 25080,т.е..25080 AXIS %1 POSITIONING MONITORINGи
25030 AXIS %1 ACTUAL VELOCITY ALARM,это вовсе не говорит о физичеcкой неисправности оси.Причиной такого поведения машины может являться неcоответствие линейных параметров оси их «R»-параметрам.Т.е. ,грубо говоря,программа пользователя,точнее,»R»-параметры домиков ,пытаются запихать оcь в то место,куда она физически зайти не может!Короче,бери программистов и заставь проверить все «домики» начиная с параметра «R28»,кажется,а уже потом,если «R» параметры в порядке,начинать мучить оси параметрами MD 36200,это AX VELO LIMIT.
А вот параметр MD 322000POSCTRL GAINлучше вернуть назад,чтобы не перегреть драйвер!Ведь,если бы была физическая проблема с осью,то и команда «REFERENCE POINT» не отрабатывала бы!
Добавлено 02-08-2009 11:27
Теперь ASm,я немогу, не зная архитектуры машины, рекомендовать вышибать ей «мозги»!Можно наломать серьезных дров!Тем более на такой коварной штуке,кaк PCU-20!Тут,прежде чем решиться на инсталляцию,нужно все продумать,-каждый шаг,найти всю документацию по NCK и PLC,разобраться с приоритетами устройств,а уже потом начинать инсталляцию!Закинь в личку инфу по твоей машине,-тогда смогу чем-то помочь,а так, рекомендовать что- то я немогу!
Добавлено 02-08-2009 11:38
Уровень доступа и приоритет устройств PCU-20 определяется или программно,установками NCK,или переключателями внутри самого PCU-20,это зависит от модификации устройства.Пытаться щелкать переключателями,в любом случае,-не стоит!Советую,-ищи документы на машину,если машину поставляли немцы,-обязaтельно должно быть описание и комплект инсталляционных файлов!
- 2 Авг 2009
Короче,бери программистов и заставь проверить все «домики» начиная с параметра «R28»
Собственно в том-то и дело ,что программистов по синумерику у нас нет, служба автоматики не знает станок совершенно! Приходиться разбираться самим! Если можно разьяснить подробнее по настройке скоростей , корректировок и R параметры. Буду признателен!
- 10 Авг 2009
Коллеги,извиняюсь за паузу,-жуткое количество вызовов на неисправности!Разгребу завалы,-продолжим и всем отвечу!
- 12 Авг 2009
Итак,мы знаем,что существуют линейные огрaничители движения осей,их два вида ,-программируемые ограничители и физические,т.е. конечники.Оси ,на всех машинах ЧПУ, двигаются согласно подпрограммам движения L-***(SUBPROGAM,или в простонародье,-суброотины).Соoтветственно,описываются эти подпрограммы «R»-параметрами.Вот ,если значения R параметров выходят за рамки значений линейных ограничителей и возникают такие проблемы,как неисправность 25080.
Каждая машина имеет свои конструктивные особенности,поэтому нужно внимательно прочитать в документации программного обеспечения раздел «SUBPROGRAM» таблицу R-параметров.Уменя под рукой R-параметры шлифовального станка «BLOHM»,собранного на базе SINUMERIK-840D,я приведу пример суброотины L-901,это нарезка профиля на камень.
R00= -INITIAL PROFILING
R05= DRESING OR CRUSHING
R09= FEED RATE FOR PROFILE DEPTH
R12= PERIPHERAL SPEED OF WEEL(m/s or ft/sec)
R14= DRESSING INFEED SPEED PER EACH REVOLUTION(0.001mm/rev)
R16= PEA SENSE OF ROTATION
R28= DRESSING AMOUNT
R32= APPROACH DIMENSION Y-AXIS GRINDING WHELL/PROFILING ROLL
R35=SAFETY LEVEL/SAFETY POSITION OF Y-AXIS POSITION
R48= NUMBER OF ROLL-OUT REVOLUTIONS
_
Таким образом,если R35 загнан за линейный ограничитель,обязательно должна возникнуть неисправность 25080!
Добавлено 12-08-2009 14:21
Эти подпрограммы стандартны,т.е. достаточно проверить параметры(естественно,по таблице для данной машины!) имеющие отношение к сбойной оси,в нашем случае,это R-35.Но я всегда рекомендую проверить и остальные параметры,т.к. очень часто оперaторы по ошибке,загоняют туда всякий мусор.
Добавлено 12-08-2009 14:30
Маленькая тонкость.Во вcех машинах есть возможность корректировки тела подпрограммы.Хочу предупредить,не лезьте в тело подпрограммы,кроме корректировки метки конца программы «M17»!Если суброотина не работает,найдите ее на инсталляционном диске,(она идет с расширением «SPF») перепишите ее,проверьте метку M17 и все будет OK!
- 14 Авг 2009
Здравствуй Андрей. Раньше написать не мог, по причине болезни. Пробовал делать все действия, что ты советовал. Но что то все равно идет не так.http://monitor.net.ru/forum/images/smileys/sad.gif Андрей, хочу попросить, можеш сбросить мне в личку номер своего мобильного.
Рылся тут по сайтам и нашел мануалы на русском по SIMODRIVE-611, SINUMERIK и SINAMICS. Одно немного напрягает, через весь экран защитная надпись.
Выкладываю адрес сайта в общак, может кому то будет интересно:
ссылка скрыта от публикации /
- 14 Авг 2009
Одно немного напрягает, через весь экран защитная надпись.
Ломаеш PDF программой «Advanced PDF Password Recovery» , потом любым редактором например «VeryPDF PDF Editor» убираеш ненавистную надпись, я еще для ускорения этого дела ставил софтину «Macro ToolsWorks» она записывает нажатия клавиш и позиции курсора можно автоматизировать удаление надписей автоматически.
Добавлено 14-08-2009 19:13
andreieinav спасибо за информацию! R-параметры надеюсь не имеют отношение к R-переменным в программе?!
- 17 Авг 2009
- 18 Авг 2009
Коллеги,всем привет!
Николай8899,в книжке «ALARM LIST»,- 112 листов.Могу выложить классификационную таблицу неисправностей,или какую то ,интересующую тебя часть.Скажи конкретно,какая неисправность интересует.
martyn_80,я имел в виду R-параметры «SETTING DATA».Они подразделяются,в зависмости от идентификатора,еще на локальные и глобальные.Если интересно,могу рассказать.
Добавлено 18-08-2009 18:48
Попробую что- то найти в архиве «SIEMENS» ,-очень плoхо стал работать их cервер.Если пробьюсь,то выложу «ALARM LIST».
- 18 Авг 2009
Да!!!
Большое спасибо в моём случае любая информация
огромная находка !!
Просто оборудование старое амортизировалось в нескольких компаниях , как следствие
полезной информации «0» и документов к нему тоже !!!
Уважаемый Андрей мы с вами уже несколько раз работали, Ваши советы меня много раз выручали !!!!
А проблема у меня такая !!!
Станок работает всё нормально потом резко останавливается загораются все лампочки и чтоб запустить его снова
нужно выключить машину полностью и подождать!!!
Причем в данной ситуации нельзя посмотреть что произошло он если можно так сказать «виснет»
Раньше это было редко, а теперь чаще и чаще .
А список если можно пришлите
буду очень благодарен!!!
R-параметры «SETTING DATA»
«ALARM LIST»
- 18 Авг 2009
Если загораются все лампочки на 80-ке и машина виснет,то начинать копать надо с блока питания CPU!Это блок,рядом с батарейкой поддержки памяти.Значит,там должны быть дырочки и потенциометр регулировки напряжения логики 5V.Прежде чем вынимать БП,проверь хорошим цифровым вольтметром напругу,-она должна быть ровно,до десятых долей, 5V!Если напряжение в норме,тогда осторожно,чтобы не задеть батарейку(иначе память упадет!),внимаешь БП и начинаешь его отмывать от грязи.Доску БП вынимай очень осторожно,т.к. из за большого радиатора сзади,она может ,при применении силы ,лопнуть!Когда вытащил доcку,обязательно проверь нижнюю решетку корпуса БП,на некоторых моделях решетки покрывают фольгированным напылением,от времени покрытие вспучивается и начинает под действием потка воздуха от вентиляторов подкорачивать плату.
Добавлено 18-08-2009 22:31
Это одна из классических неисправностей этих моделей.Хуже вcего,что она- предвестница капремонта.Причинами могут быть;
1.БП -CPU
2.Платы интерфейса PLC-CPU
3.Проблемы с корзинами ,точнее с кроссплатами внутри корзин.
Буквально на той неделе пришлось полностью перебирать похожую машину.Проблема была в том,что машина подверглась воздействию коррозии.Завод находится в горах,утром в воздухе много влаги,в результате пострадал монтаж как на платах,так и на кроссплатах внутри корзин PLC CPU.
Мой совет,-не мечись начни по порядку с БП ,если надумаешь перепахивать платы,то разрисовывай все,начиная с местоположения плат и кончая положением направляющих полозьев в корзине!
- 18 Авг 2009
Спасибо завтра проверю !!!
Пришлите :
«ALARM LIST»
R-параметры «SETTING DATA»
:good:
- 19 Авг 2009
Проник ,наконец,в архив SIEMENS..Вся инфа по старым моделям SINUMERIK-810G,880,810GA удалена,остались только 840D,810DI,840DI,т.е. последние версии.
Придется выкладывать основные неисправности ALARM LIST потихоньку тут.Спешить некуда,да и способы устранения типичных неисправностей будет полезно обсудить.Часть из них уже обсуждaлась.Не беда,коллеги,наскребем информацию сами!
- 19 Авг 2009
я имел в виду R-параметры «SETTING DATA».Они подразделяются,в зависмости от идентификатора,еще на локальные и глобальные.Если интересно,могу рассказать.
да, если нетрудно!
- 19 Авг 2009
ссылка скрыта от публикации не знаю как на счет ALARM LIST, но документации на 880 много
- 19 Авг 2009
Начну с классификации неисправностей «ALARM LIST».
Hомер 2…6,8…15,40…89,-неисправности включения NC-контроллера
Номер 16…35,-сбои интерфейса RS232C(V24)
Номер 100*…120*,140*…196*,1004*…1008*,1016*,1024*…1036*,
1052*…1060*,1204*…1216*—сбои линейных оcей(axis specific)
Номер 225*,228*…231*,2000*…2031*-сбои шпинделей(spindle specific)
- 19 Авг 2009
Номер 128*…136*,226*…227*,1000*,1012*,1040*,1200*-сбои измерительной аппаратуры,счетчиков,энкодеров,оптических линеек и т.д..
Напоминаю,что «*»-это номер неисправной оси!
Номер 2000…2195,2410…2427-состояние EMERGENCY STOP,ошибки запуска ,неверные параметры запусков,связанные с запретом работы контроллеров.
Номер 7,3000…3246- программные ошибки,oшибки в параметрах MPF,SPF(программах пользоваеля ,cуброотинах)
Номер 1044*-ошибка в параметрах линейной оси(используется для версии SINUMERIK-880GA2,SOVTWARE VERSION1)
Номер 4100..4200-сбои программных циклов,ошибки параметров TOOL OFFSET
Номер 5000…5099,-сбой подпрограмм
Номер 6000…9999-сбои внутренних программ PLC
Добавлено 19-08-2009 22:48
В дальнейшем,разберем подробнее основные неисправности каждой из подгрупп.
Перейду к «R»-параметрам.
Структура «R»-параметров имеет следующий вид;
R00-R99->локальные параметры,которые в свою очередь подразделяются на параметры описывающие движение осей(R00-R49) и параметры активации счетчиков движения(R50-R99).
R100-R199->глобальные параметры,отвечающие за вызов подпрограмм.Значит,параметры R100-R109 отвечают за вызов суброотин L940(L799)-L944,параметры R110-R199,—>L898-L979.
Завтра продолжим.
- 20 Авг 2009
Специально вернулся,чтобы исправить неточность.Я писал «R100-109-отвечают за вызов суброотин L940-L944…»,это не совcем верно,они отвечают «не за вызов»,а за «описaние суброотин».Это ошибка в моем конспекте (плaн занятий в институте).
- 20 Авг 2009
Спасибо! ждем продолжения!
Полный список M-Code и G-Code Siemens Sinumerik для станков с ЧПУ / программистов с ЧПУ, которые работают в режиме диалекта ISO.
Сводная таблица команд G-кодов
Подготовительные (основные) команды / Коды | Описание |
---|---|
G00-G04 | Позиционирование инструмента |
G17-G19 | Переключение рабочих плоскостей (XY, XZ, YZ) |
G20-G21 | Не стандаризовано |
G40-G44 | Компенсация размера различных частей инструмента (длина, диаметр) |
G53-G59 | Переключение систем координат |
G80-G84 | Циклы сверления, нарезания резьбы |
G90-G92 | Переключение систем координат (абсолютная, относительная) |
G Code Siemens Sinumerik 808D(режим диалекта ISO)
G код | Описание |
G00 | Быстрый ход |
G01 | Линейное движение |
G02 | Круг / спираль по часовой стрелке |
G03 | Круг / спираль против часовой стрелки |
G04 | Время ожидания в [с] или оборотов шпинделя |
G05 | Высокоскоростной цикл резки |
G05.1 | Высокоскоростной цикл -> Вызов CYCLE305 |
G08 | Предварительное управление ВКЛ / ВЫКЛ G15 Полярные координаты отключены |
G09 | Точная остановка |
G10 | Записать смещение нулевой точки / смещение инструмента |
G10.6 | Отвод от контура (POLF) |
G11 | Завершить ввод параметра |
G16 | Полярные координаты |
G17 | Плоскость XY |
G18 | Плоскость ZX |
G19 | Плоскость т YZ |
G20 | Дюймовая система ввода |
G21 | Метрическая система ввода |
G27 | Проверка референтной позиции |
G28 | 1. Приближение к ориентиру. |
G30 | 2./3./4. Приближение к ориентиру |
G30.1 | Положение контрольной точки |
G31 | Измерение с «удалением оставшегося пути» |
G40 | Отмена выбора компенсации радиуса фрезы |
G41 | Компенсация слева от контура |
G42 | Компенсация справа от контура |
G43 | Положительная компенсация длины инструмента включена |
G44 | Отрицательная коррекция длины инструмента включена |
G49 | Компенсация длины инструмента выключена |
G50 | Масштабирование отмена |
G51 | Масштабирование |
G50.1 | Зеркальное отображение запрограммированной оси ВЫКЛ. |
G51.1 | Зеркальное отображение запрограммированной оси ВКЛ. |
G52 | Программируемое смещение нулевой точки |
G53 | Позиция подхода в системе координат станка |
G54 P0 | Внешнее смещение нулевой точки |
G54 | Выбор рабочего смещения |
G55 | Выбор рабочего смещения |
G56 | Выбор рабочего смещения |
G57 | Выбор рабочего смещения |
G58 | Выбор рабочего смещения |
G59 | Выбор рабочего смещения |
G60 | Направленное позиционирование |
G61 | Режим точной остановки |
G63 | Режим нажатия |
G64 | Режим непрерывного пути G66 Вызов модуля макроса |
G65 | Макро-вызов |
G67 | Удалить вызов модуля макроса |
G68 | Вращение ВКЛ, 2D / 3D |
G69 | Вращение ВЫКЛ. |
G72.1 | Повторение контура с вращением |
G72.2 | Повторение линейного контура |
G73 | Цикл высокоскоростного сверления глубоких отверстий со стружкодроблением |
G74 | Цикл левого нарезания резьбы |
G76 | Цикл точного сверления |
G80 | Цикл выключен |
G81 | Простой цикл сверления |
G82 | Цикл сверления зенковки |
G83 | Цикл сверления глубоких отверстий с удалением стружки |
G84 | Цикл правого нарезания резьбы |
G85 | Цикл растачивания, отвод с G01 после достижения конца по оси Z, без остановки шпинделя |
G86 | Цикл растачивания, шпиндель останавливается, а затем отвод с G00 после достижения конца по оси Z |
G87 | Обратное зенкование |
G89 | Цикл растачивания, выдержка на некоторое время, затем отвод с помощью G01, без изменения направления вращения шпинделя |
G90 | Абсолютное программирование |
G91 | Инкрементальное программирование |
G92 | Установка фактического значения |
G92.1 | Удалить фактическое значение, сбросить WKS |
G93 | обратнозависимая скорость подачи (1 / мин) |
G94 | Скорость подачи в [мм / мин, дюйм / мин] |
G95 | Революционная скорость подачи в [мм / об, дюймах / об] |
G96 | Постоянная поверхностная скорость |
G97 | Постоянная скорость резки |
G98 | Возврат к исходной точке через фиксированные циклы |
G99 | Возвращение в точку R через фиксированные циклы |
G290 | Выбор режима Сименс |
G291 | Выбор режима диалекта ISO |
Таблица технологических кодов M-Code Siemens Sinumerik
Технологические команды M-Code Siemens Sinumerik начинаются с буквы М. Включают такие действия, как:
- Сменить инструмент
- Включить/выключить шпиндель
- Включить/выключить охлаждение
- Вызвать/закончить подпрограмму
Вспомогательные (технологические) команды
Код | Описание | Пример |
---|---|---|
M00 | Приостановить работу станка до нажатия кнопки «старт» на пульте управления, так называемый «технологический останов» | G0 X0 Y0 Z100 M0; |
M01 | Приостановить работу станка до нажатия кнопки «старт», если включен режим подтверждения останова | G0 X0 Y0 Z100 M1; |
M02 | Конец программы | M02; |
M03 | Начать вращение шпинделя по часовой стрелке | M3 S2000; |
M04 | Начать вращение шпинделя против часовой стрелки | M4 S2000; |
M05 | Остановить вращение шпинделя | M5; |
M06 | Сменить инструмент | M6 T15; |
M07 | Включить дополнительное охлаждение | M3 S2000 M7; |
M08 | Включить основное охлаждение | M3 S2000 M8; |
M09 | Выключить охлаждение | G0 X0 Y0 Z100 M5 M9; |
M30 | Конец информации | M30; |
M98 | Вызов подпрограммы | M98 P101; |
M99 | Конец подпрограммы, возврат к основной программе | M99; |
Параметры команд задаются буквами латинского алфавита
Код константы | Описание | Пример |
---|---|---|
X | Координата точки траектории по оси X | G0 X0 Y0 Z100 |
Y | Координата точки траектории по оси Y | G0 X0 Y0 Z100 |
Z | Координата точки траектории по оси Z | G0 X0 Y0 Z100 |
F | Скорость рабочей подачи | G1 G91 X10 F100 |
S | Скорость вращения шпинделя | S3000 M3 |
R | Радиус или параметр стандартного цикла | G1 G91 X12.5 R12.5 или G81 R1 0 R2 -10 F50 |
D | Параметр коррекции выбранного инструмента | M06 T1 D1 |
P | Величина задержки или число вызовов подпрограммы | M04 P101 или G82 R3 Z-10 P1000 F50 |
I,J,K | Параметры дуги при круговой интерполяции | G03 X10 Y10 I0 J0 F10 |
L | Вызов подпрограммы с данной меткой | L12 P3 |
- 16000 Channel %1 block %2 invalid value for lifting direction
- 16005 Channel %1 block %2 invalid value for lifting distance
- 16010 Channel %1 block %2 machining stop after lift fast
- 16015 Channel %1 block %2 wrong axis identifier %3
- 16016 Channel %1 block %2 no retraction position programmed for axis %3
- 16020 Channel %1 repositioning in block %2 is not possible
- 16100 Channel %1 block %2 spindle %3 not available in the channel
- 16105 Channel %1 block %2 spindle %3 cannot be assigned
- 16110 Channel %1 block %2 spindle %3 for dwell time not in control mode
- 16120 Channel %1 block %2 invalid index for tool fine compensation
- 16130 Channel %1 block %2 instruction not allowed with FTOCON
- 16140 Channel %1 block %2 FTOCON not allowed
- 16150 Channel %1 block %2 invalid spindle number with PUTFTOCF
- 16200 Channel %1 block %2 spline and polynominal interpolation not available
- 16300 Channel %1 block %2 denominator polynominal with zero places within parameter range not allowed
- 16400 Channel %1 block %2 positioning axis %3 cannot participate in spline
- 16410 Channel %1 block %2 axis %3 is not a geometry axis
- 16420 Channel %1 block %2 axis %3 programmed repeatedly
- 16421 Channel %1 block %2 angle %3 programmed repeatedly in the block
- 16422 Channel %1 block %2 angle %3 programmed repeatedly in the block
- 16423 Channel %1 block %2 angle %3 programmed repeatedly in the block
- 16424 Channel %1 block %2 coordinate %3 programmed repeatedly in the block
- 16430 Channel %1 block %2 geometry axis %3 cannot traverse as positioning axis in rotated coordinate system
- 16440 Channel %1 block %2 rotation programmed for non-existent geometry axis
- 16500 Channel %1 block %2 chamfer or rounding negative
- 16510 Channel %1 block %2 no facing axis available
- 16700 Channel %1 block %2 axis %3 invalid feed type
- 16710 Channel %1 block %2 axis %3 master spindle not programmed
- 16715 Channel %1 block %2 axis %3 spindle not in standstill
- 16720 Channel %1 block %2 axis %3 thread lead is zero
- 16730 Channel %1 block %2 axis %3 wrong parameter
- 16740 Channel %1 block %2 no geometry axis programmed
- 16750 Channel %1 block %2 axis %3 SPCON not programmed
- 16751 Channel %1 block %2 spindle/axis %3 SPCOF not executable
- 16755 Channel %1 block %2 no stop required
- 16760 Channel %1 block %2 axis %3 S value missing
- 16761 Channel %1 block %2 axis/spindle %3 not programmable in the channel
- 16762 Channel %1 block %2 spindle %3 thread function is active
- 16763 Channel %1 block %2 axis %3 programmed speed is illegal (zero or negative)
- 16770 Channel %1 block %2 axis %3 no measuring system available
- 16771 Channel %1 following axis %2 overlaid movement not enabled
- 16776 Channel %1 block %2 curve table %3 does not exist for axis %4
- 16777 Channel %1 block %2 coupling: following axis %3 for lead axis %4 not available
- 16778 Channel %1 block %2 coupling: Ring coupling at following axis %3 and leading axis %4 impermissible
- 16779 Channel %1 block %2 coupling: too many couplings for axis %3, see active leading axis %4
- 16780 Channel %1 block %2 following spindle/axis missing
- 16781 Channel %1 block %2 master spindle/axis missing
- 16782 Channel %1 block %2 following spindle/axis %3 not available
- 16783 Channel %1 block %2 master spindle/axis %3 not available
- 16785 Channel %1 block %2 identical spindles/axes %3
- 16787 Channel %1 block %2 coupling parameter not changeable
- 16788 Channel %1 block %2 cyclic coupling
- 16789 Channel %1 block %2 multiple link
- 16790 Channel %1 block %2 Parameter is zero or missing
- 16791 Channel %1 block %2 parameter is not relevant
- 16792 Channel %1 block %2 too many couplings for axis/spindle %3
- 16793 Channel %1 block %2 coupling of axis %3 prohibits transformation change
- 16794 Channel %1 block %2 coupling of axis/spindle %3 prohibits reference point approach
- 16795 Channel %1 block %2 string cannot be interpreted
- 16796 Channel %1 block %2 coupling not defined
- 16797 Channel %1 block %2 coupling is active
- 16798 Channel %1 block %2 axis %3 is following axis and prohibits axis container rotation
- 16799 Channel %1 block %2 axis %3 is master axis and prohibits axis container rotation
- 16800 Channel %1 block %2 traverse instruction DC/CDC for axis %3 not allowed
- 16810 Channel %1 block %2 traverse instruction ACP for axis %3 not allowed
- 16820 Channel %1 block %2 traverse instruction ACN for axis %3 not allowed
- 16830 Channel %1 block %2 incorrect position programmed for axis/spindle %3
- 16903 Channel %1 program control: action %2 not allowed in the current state
- 16904 Channel %1 program control: action %2 not allowed in the current state
- 16905 Channel %1 program control: action %2 not allowed
- 16906 Channel %1 program control: action %2 is aborted due to an alarm
- 16907 Channel %1 action %2 only possible in stop state
- 16908 Channel %1 action %2 only possible in reset state or at the block end
- 16909 Channel %1 action %2 not allowed in current mode
- 16911 Channel %1 mode change is not allowed
- 16912 Channel %1 program control: action %2 only possible in reset state
- 16913 Mode group %1 channel %2 mode change: action %3 not allowed
- 16914 Mode group %1 channel %2 mode change: action %3 not allowed
- 16915 Channel %1 action %2 not allowed in the current block
- 16916 Channel %1 repositioning: action %2 not allowed in the current state
- 16918 Channel %1 for action %2 all channels must be in reset state
- 16919 Channel %1 action %2 is not allowed due to a pending alarm
- 16920 Channel %1 action %2 is already active
- 16921 Channel %1 mode group %2 machine data: channel/mode group assignment not allowed or assigned twice
- 16922 Channel %1 subprograms: action %2 maximum nesting depth exceeded
- 16923 Channel %1 program control: action %2 not allowed in the current state
- 16924 Channel %1 caution: program test modifies tool management data
- 16925 Channel %1 program control: action %2 not allowed in the current state, action %3 active
- 16926 Channel %1 channel coordination: action %2 not allowed in block %3, marker %4 is already set
- 16927 Channel %1 action %2 at active interrupt treatment not allowed
- 16928 Channel %1 interrupt treatment: action %2 not possible
- 16930 Channel %1: preceding block and current block %2 must be separated through an executable block
- 16931 Channel %1 subprograms: action %2 maximum nesting depth exceeded
- 16932 Channel %1 conflict when activating user data type %2
- 16933 Channel %1 interrupt treatment: action %2 not allowed in the current state
- 16934 Channel %1 interrupt treatment: action %2 not possible due to stop
- 16935 Channel %1 action %2 not possible due to search run
- 16936 Channel %1 action %2 not possible due to active dry run
- 16937 Channel %1 action %2 not possible due to program test
- 16938 Channel %1 action %2 aborted due to active gear change
- 16939 Channel %1 action %2 rejected due to active gear change
- 16940 Channel %1 action %2 wait for gear change
- 16941 Channel %1 action %2 rejected because no program event has been executed yet
- 16942 Channel %1 start program command action %2 not possible
- 16943 Channel %1 action %2 not possible due to ASUP
- 16944 Channel %1 action %2 not possible due to active search blocks
- 16945 Channel %1 action %2 delayed up to the block end
- 16946 Channel %1 start via START is not allowed
- 16947 Channel %1 start via PLC is not allowed
- 16948 Channel %1 dependent channel %2 still active
- 16949 Correspondence between marker of channel %1 and channel %2 is invalid.
- 16950 Channel %1 search run with hold block
- 16951 Channel %1 search run in a program section that cannot be searched
- 17000 Channel %1 block %2 maximum number of symbols exceeded
- 17001 Channel %1 block %2 no memory left for tool/magazine data
- 17010 Channel %1 block %2 no memory left
- 17020 Channel %1 block %2 illegal array index 1
- 17030 Channel %1 block %2 illegal array index 2
- 17040 Channel %1 block %2 illegal axis index
- 17050 Channel %1 block %2 illegal value
- 17055 Channel %1 block %2 GUD variable not existing
- 17060 Channel %1 block %2 requested data area too large
- 17070 Channel %1 block %2 data is write-protected
- 17080 Channel %1 block %2 %3 value below lower limit
- 17090 Channel %1 block %2 %3 value exceeds upper limit
- 17095 Channel %1 block %2 invalid value
- 17100 Channel %1 block %2 digital input/comparator no. %3 not activated
- 17110 Channel %1 block %2 digital output no. %3 not activated
- 17120 Channel %1 block %2 analog input no. %3 not activated
- 17130 Channel %1 block %2 analog output no. %3 not activated
- 17140 Channel %1 block %2 NCK output %3 is assigned to a function via machine data
- 17150 Channel %1 block %2 maximum of %3 NCK outputs programmable in the block
- 17160 Channel %1 block %2 no tool selected
- 17170 Channel %1 block %2 number of symbols too large
- 17180 Channel %1 block %2 illegal D number
- 17181 Channel %1 block %2 T no.= %3, D no.= %4 not existing
- 17182 Channel %1 block %2 illegal sum correction number
- 17188 Channel %1 D number %2 defined in tool T no. %3 and %4
- 17189 Channel %1 D number %2 of tools defined on magazine/location %3 and %4
- 17190 Channel %1 block %2 illegal T number
- 17191 Channel %1 block %2 T= %3 not existing, program %4
- 17192 TO unit %1 invalid tool designation of ‘%2’, duplo no. %3. No more replacement tools possible in ‘%4’.
- 17193 Channel %1 block %2 the active tool is no longer on toolholder no./spindle no. %3, program %4
- 17194 Channel %1 block %2 no suitable tool found
- 17200 Channel %1 block %2 deleting tool data not possible
- 17202 Channel %1 block %2 deleting magazine data not possible
- 17210 Channel %1 block %2 access to variable not possible
- 17212 Channel %1 tool management: Load manual tool %3, duplo no. %2 onto spindle/ toolholder %4
- 17214 Channel %1 tool management: remove manual tool %3 from spindle/toolholder %2
- 17216 Channel %1 tool management: remove manual tool from spindle/toolholder %4 and load manual tool %3, duplo no. %2
- 17220 Channel %1 block %2 tool not existing
- 17230 Channel %1 block %2 Duplo no. already assigned
- 17240 Channel %1 block %2 illegal tool definition
- 17250 Channel %1 block %2 illegal magazine definition
- 17260 Channel %1 block %2 illegal magazine location definition
- 17262 Channel %1 block %2 illegal tool adapter operation
- 17270 Channel %1 block %2 call-by-reference: illegal variable
- 17500 Channel %1 block %2 axis %3 is not an indexing axis
- 17501 Channel %1 block %2 indexing axis %3 with Hirth tool system is active
- 17502 Channel %1 block %2 indexing axis %3 with Hirth tooth system stop is delayed
- 17503 Channel %1 block %2 indexing axis %3 with Hirth tooth system and axis not referenced
- 17510 Channel %1 block %2 invalid index for indexing axis %3
- 17600 Channel %1 block %2 preset on transformed axis %3 not possible
- 17605 Channel %1 block %2 axis %3 transformation active: inhibits rotation of axis container
- 17610 Channel %1 block %2 axis %3 involved in the transformation, action cannot be carried out
- 17620 Channel %1 block %2 approaching fixed point for transformed axis %3 not possible
- 17630 Channel %1 block %2 referencing for transformed axis %3 not possible
- 17640 Channel %1 block %2 spindle operation for transformed axis %3 not possible
- 17650 Channel %1 block %2 machine axis %3 not programmable
- 17800 Channel %1 block %2 illegally coded position programmed
- 17900 Channel %1 block %2 axis %3 is no machine axis
- 18000 Channel %1 block %2 NCK-specific protection zone %3 wrong. Error code %4
- 18001 Channel %1 block %2 channel-specific protection zone %3 incorrect. Error code %4
- 18002 Channel %1 block %2 NCK protection zone %3 cannot be activated. Error code %4
- 18003 Channel %1 block %2 NCK protection zone %3 cannot be activated.Error code %4
- 18004 Channel %1 block %2 orientation of workpiece-related protection zone %3 does not correspond to the orientation of tool-related protection zone %4
- 18005 Channel %1 block %2 serious error in definition of NCK-specific protection zone %3
- 18006 Channel %1 block %2 serious error in definition of channel-specific protection zone %3
- 18100 Channel %1 block %2 invalid value assigned to FXS[]
- 18101 Channel %1 block %2 invalid value assigned to FXST[]
- 18102 Channel %1 block %2 invalid value assigned to FXSW[]
- 18200 Channel %1 block %2 curve table: block search stop not allowed with definition CTABDEF
- 18201 Channel %1 block %2 curve table: table %3 does not exist
- 18202 Channel %1 block %2 curve table: instruction CTABEND without CTABDEF not allowed
- 18300 Channel %1 block %2 frame: fine shift not possible
- 18310 Channel %1 block %2 frame: illegal rotation
- 18311 Channel %1 block %2 frame: illegal instruction
- 18312 Channel %1 block %2 frame: fine shift not configured
- 18313 Channel %1 block %2 frame: illegal switchover of geometry axes
- 18314 Channel %1 block %2 frame: type conflict
- 18400 Channel %1 block %2 language change not possible:
- 20000 Channel %1 axis %2 reference cam not reached
- 20001 Channel %1 axis %2 no cam signal present
- 20002 Channel %1 axis %2 zero mark not found
- 20003 Channel %1 axis %2 measuring system error
- 20004 Channel %1 axis %2 reference mark missing
- 20005 Channel %1 axis %2 reference point approach aborted
- 20006 Channel %1 axis %2 reference point creep velocity not reached
- 20007 Channel %1 axis %2 reference point approach requires 2 measuring systems
- 20008 Channel %1 axis %2 reference point approach requires second referenced measuring system
- 20050 Channel %1 axis %2 handwheel mode active
- 20051 Channel %1 axis %2 handwheel mode not possible
- 20052 Channel %1 axis %2 already active
- 20053 Channel %1 axis %2 DRF, FTOCON, external zero point offset not possible
- 20054 Channel %1 axis %2 wrong index for indexing axis in JOG mode
- 20055 Channel %1 master spindle not present in JOG mode
- 20056 Channel %1 axis %2 no revolutional feedrate possible. Axis/spindle %3 stationary
- 20057 Channel %1 block %2 revolutional feedrate for axis/spindle %3 is <= zero
- 20058 Channel %1 axis %2 revolutional feedrate: illegal feed source
- 20060 Channel %1 axis %2 cannot be traversed as geometry axis
- 20061 Channel %1 axis %2 cannot be traversed as orientation axis
- 20062 Channel %1 axis %2 already active
- 20063 Channel %1 axis %2 orientation axes cannot be traversed without transformation
- 20065 Channel %1 master spindle not defined for geometry axes in JOG mode
- 20070 Channel %1 axis %2 programmed end position is behind software limit switch %3
- 20071 Channel %1 axis %2 programmed end position is behind working area limit %3
- 20072 Channel %1 axis %2 is not an indexing axis
- 20073 Channel %1 axis %2 cannot be repositioned
- 20074 Channel %1 axis %2 wrong index position
- 20075 Channel %1 axis %2 can currently not oscillate
- 20076 Channel %1 axis %2 oscillating – mode change not possible
- 20077 Channel %1 axis %2 programmed position is behind software limit switch %3
- 20078 Channel %1 axis %2 programmed position is behind working area limit %3
- 20079 Channel %1 axis %2 oscillation path length %3 <= 0
- 20080 Channel %1 axis %2 no handwheel assigned for overlaid motion
- 20085 Channel %1 contour handwheel: traverse direction or overtravel of beginning of block not allowed
- 20090 Axis %1 travel to fixed stop not possible. Check programming and axis data.
- 20091 Axis %1 has not reached fixed stop
- 20092 Axis %1 travel to fixed stop still active
- 20093 Axis %1 standstill monitoring at fixed-stop end point has been triggered
- 20094 Axis %1 function has been aborted
- 20095 Axis %1 illegal torque, current torque %2
- 20096 Axis %1 brake test aborted, additional information %2
- 20100 Channel %1: invalid configuration for digitizing function
- 20101 Communication with the digitizer not possible
- 20102 Channel %1: No or invalid trafo at digitizing active
- 20103 Channel %1: digitizing module does not support 3+2 axis digitizing
- 20105 Channel %1: axes stopped by digitizer. Error code: %2
- 20106 Emergency stop set by the digitizer
- 20108 Invalid data package received from the digitizer. Error codes: %1, %2
- 20109 Error in communication with the digitizer: status code of com-circuit: %1
- 20120 Axis %1: too many compensation relations
- 20121 Axis %1: Configuration error in compensation table %2
- 20122 Compensation table %1: invalid axis assignment
- 20123 Axis %1: different output assignment of multiplied tables
- 20124 Axis %1: sum of compensation values too large
- 20125 Axis %1: change of compensation value is too rapid
- 20130 Channel %1 contour tunnel monitoring
- 20140 Channel %1 motion synchronous action: traversing of command axis %2 see NC alarm %3
- 20141 Channel %1 motion synchronous action: illegal axis type
- 20142 Channel %1 command axis %2: rotation of axis container already enabled
- 20143 Channel %1 axis %2 command axis cannot be started as it is controlled by the PLC
- 20144 Channel %1 block %2 motion synchronous action: system variable access not possible
- 20145 Channel %1 block %2 motion synchronous action: arithmetic error
- 20146 Channel %1 block %2 motion synchronous action: nesting depth exceeded
- 20147 Channel %1 block %2 motion synchronous action: command not executable
- 20148 Channel %1 block %2 motion synchronous action: internal error %3
- 20149 Channel %1 block %2 motion synchronous action: illegal index
- 20150 Channel %1 tool management: PLC terminates interrupted command
- 20160 Channel %1 tool management: PLC can terminate only incorrectly aborted commands
- 20170 Channel %1 machine data $AC_FIFO invalid
- 20200 Channel %1 invalid spindle number %2 with tool fine compensation
- 20201 Channel %1 spindle %2 no tool assigned
- 20203 Channel %1 no active tool
- 20204 Channel %1 PUTFTOC command not allowed with FTOCOF
- 20210 Channel %1 block %3 spindle %2 wrong values for centerless grinding
- 20211 Channel %1 block %3 spindle %2 support point beyond range limits
- 21600 Monitoring for ESR active
- 21610 Channel %1 axis %2 encoder %3 frequency limit exceeded
- 21611 Channel %1 NC-controlled Extended Stop/Retract triggered
- 21612 Channel %1 axis %2 VDI signal ‘Servo enable’ reset during motion
- 21613 Axis %1 measuring system changing
- 21614 Channel %1 axis %2 hardware limit switch %3
- 21615 Channel %1 axis %2 taken from traverse mode to follow-up mode
- 21616 Channel %1 block %2 overlaid motion active at transformation switchover
- 21617 Channel %1 block %2 transformation does not allow to traverse the pole
- 21618 Channel %1 as from block %2 transformation active: overlaid motion too great
- 21619 Channel %1 block %2 transformation active: motion not possible
- 21650 Channel %1 axis %2 overlaid motion not allowed
- 21660 Channel %1 block %2 axis %3 conflict between SYNACT: $AA_OFF and CORROF
- 21665 Channel %1 $AA_TOFF cleared
- 21670 Channel %1 block %2 illegal change of tool direction with $AA_TOFF active
- 21700 Channel %1 block %3 axis %2 touch probe already deflected, edge polarity not possible
- 21701 Channel %1 block %3 axis %2 measurement not possible
- 21702 Channel %1 block %3 axis %2 measurement aborted
- 21703 Channel %1 block %3 axis %2 touch probe not deflected, illegal edge polarity
- 21740 Output value at analog output no. %1 has been limited
- 21750 Error during output of cam signals via timer
- 21760 Channel %1 block %2 too many auxiliary functions programmed
- 21800 Channel %1 workpiece setpoint %2 reached
- 22000 Channel %1 block %3 spindle %2 change of gear stage not possible
- 22010 Channel %1 block %3 spindle %2 actual gear stage differs from requested gear stage
- 22011 Channel %1 block %3 spindle %2 change to programmed gear stage not possible
- 22012 Channel %1 block %2 leading spindle %3 is in simulation.
- 22013 Channel %1 block %2 dependent spindle %3 is in simulation.
- 22014 Channel %1 block %2. The dynamics of leading spindle %3 and dependent spindle %4 is too variably
- 22020 Channel %1 block %3 spindle %2 gear step change position not reached
- 22040 Channel %1 block %3 spindle %2 is not referenced with zero marker
- 22045 Block %2 spindle/axis %3 not available in channel %1 because active in channel %4
- 22050 Channel %1 block %3 spindle %2 no transition from speed control mode to position control mode
- 22051 Channel %1 block %3 spindle %2 reference mark not found
- 22052 Channel %1 block %3 spindle %2 no standstill on block change
- 22053 Channel %1 block %3 spindle %2 reference mode not supported
- 22054 Channel %1 block %3 spindle %2 improper punching signal
- 22055 Channel %1 block %3 spindle %2 configured positioning speed is too high
- 22060 Channel %1 position control expected for axis/spindle %2
- 22062 Channel %1 axis %2 reference point approach: zero marker search velocity (MD) is not reached
- 22064 Channel %1 axis %2 reference point approach: zero marker search velocity (MD) is too high
- 22065 Channel %1 tool management: Tool motion is not possible, as tool %2 with Duplo no. %3 is not in magazine %4
- 22066 Channel %1 tool management: Tool change is not possible, as tool %2 with Duplo no. %3 is not in magazine %4
- 22067 Channel %1 tool management: tool change not possible since there is no tool available in tool group %2
- 22068 Channel %1 block %2 tool management: no tool available in tool group %3
- 22069 Channel %1 block %2 tool management: No tool available in tool group %3, program %4
- 22070 TO unit %1 Please change tool T= %2 into magazine. Repeat data backup
- 22071 TO unit %1 tool %2 duplo no. %3 is active, but not in the magazine area under consideration
- 22100 Channel %1 block %3 spindle %2 chuck speed exceeded
- 22200 Channel %1 spindle %2 axis stopped during tapping
- 22250 Channel %1 spindle %2 axis stopped during thread cutting
- 22260 Channel %1 spindle %2 thread might be damaged
- 22270 Channel %1 block %2 maximum velocity of thread axis at position %3 reached
- 22275 Channel %1 block %2 zero velocity of thread axis at position %3 reached
- 22280 Channel %1 in block %2: Prog. acceleration path too short %3, %4 required
- 22320 Channel %1 block %2 PUTFTOCF command could not be transferred
- 22321 Channel %1 axis %2 PRESET not allowed during traverse motion
- 22322 Channel %1 axis %2 PRESET: illegal value
- 25000 Axis %1 hardware fault of active encoder
- 25001 Axis %1 hardware fault of passive encoder
- 25010 Axis %1 pollution of measuring system
- 25011 Axis %1 pollution of passive encoder
- 25020 Axis %1 zero mark monitoring of active encoder
- 25021 Axis %1 zero mark monitoring of passive encoder
- 25022 Axis %1 encoder %2 warning %3
- 25030 Axis %1 actual velocity alarm limit
- 25031 Axis %1 actual velocity warning limit
- 25040 Axis %1 standstill monitoring
- 25042 Axis %1 standstill monitoring during torque/force limitation
- 25050 Axis %1 contour monitoring
- 25060 Axis %1 speed setpoint limitation
- 25070 Axis %1 drift value too large
- 25080 Axis %1 positioning monitoring
- 25100 Axis %1 measuring system switchover not possible
- 25105 Axis %1 measuring systems differ considerably
- 25110 Axis %1 selected encoder not available
- 25200 Axis %1 requested set of parameters invalid
- 25201 Axis %1 drive fault
- 25202 Axis %1 waiting for drive
- 26000 Axis %1 clamping monitoring
- 26001 Axis %1 parameterization error: friction compensation
- 26002 Axis %1 encoder %2 parameterization error: number of encoder marks
- 26003 Axis %1 parameterization error: lead screw pitch
- 26004 Axis %1 encoder %2 parameterization error: grid point distance with linear encoders
- 26005 Axis %1 parameterization error: output rating
- 26006 Axis %1 encoder %2 encoder type/output type %3 not possible
- 26007 Axis %1 QEC: invalid coarse step size
- 26008 Axis %1 QEC: invalid fine step size
- 26009 Axis %1 QEC: memory overflow
- 26010 Axis %1 QEC: invalid acceleration characteristic
- 26011 Axis %1 QEC: invalid measuring periods
- 26012 Axis %1 QEC: feed forward control not active
- 26014 Axis %1 machine data %2 invalid value
- 26015 Axis %1 machine data %2[%3] invalid value
- 26016 Axis %1 machine data %2 invalid value
- 26017 Axis %1 machine data %2[%3] invalid value
- 26018 Axis %1 setpoint output drive %2 used more than once
- 26019 Axis %1 encoder %2 measurement not possible with this controller module
- 26020 Axis %1 encoder %2 hardware fault %3 during encoder initialization
- 26022 Axis %1 encoder %2 measurement with simulated encoder not possible
- 26024 Axis %1 machine data %2 value changed
- 26025 Axis %1 machine data %2[%3] value changed
- 26030 Axis %1 encoder %2 absolute position lost
- 26031 Axis %1 configuration error master-slave
- 26032 Axis %1 master-slave not configured
- 26050 Axis %1 parameter set change from %2 to %3 not possible
- 26051 Channel %1 in block %2 unanticipated stop crossed in continuous path mode
- 26052 Channel %1 in block %2: path velocity too high for auxiliary function output
- 26070 Channel %1 axis %2 cannot be controlled by the PLC, max. number exceeded
- 26072 Channel %1 axis %2 cannot be controlled by the PLC
- 26074 Channel %1 switching off PLC control of axis %2 not allowed in the current state
- 26080 Channel %1 retraction position of axis %2 not programmed or invalid
- 26081 Channel %1 axis trigger of axis %2 was activated, but axis is not PLC- controlled
- 26100 Axis %1 drive %2 sign of life missing
- 26101 Axis %1 drive %2 communication failure
- 26102 Axis %1 drive %2 sign of life missing
- 26105 Drive of axis %1 not found
- 26106 Encoder %2 of axis %1 not found
- 26110 Independent drive stop/retract triggered
- 27000 Axis %1 is not safely referenced
- 27001 Axis %1 error in a monitoring channel, code %2, values: NCK %3, drive %4
- 27002 Axis %1 test stop is running
- 27003 Checksum error found: %1 %2
- 27004 Axis %1, difference safe input %2, NCK %3, drive %4
- 27005 Axis %1 error in data cross check: static actual value difference
- 27006 Axis %1 Test ext. pulse deletion running
- 27007 Axis %1 acceptance test mode is active
- 27008 Axis %1 SW limit switch deactivated
- 27010 Axis %1 tolerance for safe standstill exceeded
- 27011 Axis %1 safe velocity exceeded
- 27012 Axis %1 safe end position exceeded
- 27013 Axis %1 safe braking ramp exceeded
- 27020 Axis %1 stop E triggered
- 27021 Axis %1 stop D triggered
- 27022 Axis %1 stop C triggered
- 27023 Axis %1 stop B triggered
- 27024 Axis %1 stop A triggered
- 27030 Axis %1 function not supported on this 611D module
- 27031 Axis %1 limit value for safe velocity %2 at gear ratio %3 too large (max. %4)
- 27032 Axis %1 checksum error of safe monitoring. Confirmation and re-test required!
- 27033 Axis %1 parameterization of MD %2[%3] invalid
- 27034 Parameterization of MD %1 invalid
- 27090 Error in data cross check NCK-PLC, %1[%2], NCK: %3; %4 ALSI
- 27091 Error in data cross check NCK PLC, stop of %1
- 27092 Communication broken off during NCK PLC data cross check, error detected by %1
- 27093 Checksum error NCK-SPL, %1, %2, %3
- 27094 Write access to system variable %1 only allowed from NCK-SPL
- 27095 %1 SPL protection not activated
- 27096 SPL start not allowed
- 27100 At least one axis is not safely referenced
- 27101 Axis %1 difference in function safe operational stop, NCK: %2 drive: %3
- 27102 Axis %1 difference in function safe velocity %2, NCK: %3 drive: %4
- 27103 Axis %1 difference in function safe limit position %2, NCK: %3 drive: %4
- 27104 Axis %1 difference in function safe cam plus %2, NCK: %3 drive: %4
- 27105 Axis %1 difference in function safe cam minus %2, NCK: %3 drive: %4
- 27106 Axis %1 difference in function safe velocity nx, NCK: %2 drive: %3
- 27107 Axis %1 difference in function cam modulo monitoring, NCK: %2 drive: %3
- 27124 Stop A triggered at least in 1 axis
- 27200 PROFIsafe: cycle time %1 [ms] too long
- 27201 PROFIsafe: MD %1[%2]: bus segment %3 error
- 27202 PROFIsafe: MD %1[%2]: address %3 error
- 27203 PROFIsafe: MD %1[%2]: SPL assignment error
- 27204 PROFIsafe: double assignment MD %1[%2] – MD %3[%4]
- 27220 PROFIsafe: Number of NCK F modules (%1) <> number of DP modules (%2)
- 27221 PROFIsafe: NCK F module MD %1[%2] unknown
- 27222 PROFI safe: S7 F module PROFI safe address %1 unknown
- 27223 PROFIsafe: NCK F module MD %1[%2] is not a %3 module
- 27224 PROFIsafe: F module MD %1[%2] – MD %3[%4]: double assignment of PROFIsafe address
- 27225 PROFIsafe: slave %1, configuration error %2
- 27240 PROFIsafe: DP M not running up, DP info: %1
- 27241 PROFIsafe: DP M version different, NCK: %1, PLC: %2
- 27242 PROFIsafe: F module %1, %2 faulty
- 27250 PROFIsafe: configuration in DP M changed; error code %1 – %2
- 27251 PROFIsafe: F module %1, %2 reports error %3
- 27252 PROFIsafe: Slave %1, sign-of-life error
- 27253 PROFIsafe: communication fault F master component %1, error %2
- 27254 PROFIsafe: F module %1, error on channel %2; %3
- 27255 PROFIsafe: F module %1, general error
- 27256 PROFIsafe: Current cycle time %1 [ms] > parameterized cycle time
- 27299 PROFIsafe: Diagnosis %1 %2 %3 %4
- 28000 NCU link connection to all other NCUs of the link network has been aborted
- 28001 NCU link connection to the NCU %1 of the link network has been aborted
- 28002 Error on activation of machine data, NCU network-wide machine data were modified by NCU %1
- 28004 NCU link: NCU %1 of the link network is not on the bus
- 28005 NCU link: NCU %1 of the link network not running synchronously
- 28007 NCU link: conflict in configuration data of NCU %1
- 28008 NCU link: conflict in timer setting of NCU %1
- 28009 NCU link: conflict in bus parameters of NCU %1
- 28010 NCU link: the NCU %1 has not received a message
- 28011 IPO time insufficient for NCU link. Link cycle time: %1
- 28012 NCU link: synchronization cycle signal failure %1 times
- 28020 NCU link: too many link axes configured %1
- 28030 Serious alarm on NCU %1, axes in follow-up mode
- 28031 Serious alarm on NCU %1 not yet acknowledged, axes still in follow-up mode
- 28032 Emergency stop activated on NCU %1, axes in follow-up mode
- 28033 Emergency stop on NCU % 1, axes still in follow-up mode
- 29033 Channel %1 axis change of axis %2 not possible, PLC axis movement not yet completed
- 60000 Channel %1 block %2:
- 61000 Channel %1 block %2 no tool compensation active
- 61001 Channel %1 block %2 thread lead incorrect
- 61002 Channel %1 block %2 machining type wrongly defined
- 61003 Channel %1 block %2 no feed programmed in the cycle
- 61004 Channel %1 block %2 configuration geometry axis incorrect
- 61005 Channel %1 block %2 3rd geometry axis not present
- 61006 Channel %1 block %2 tool radius too large
- 61007 Channel %1 block %2 tool radius too small
- 61009 Channel %1 block %2 active tool number = 0
- 61010 Channel %1 block %2 finishing allowance too large
- 61011 Channel %1 block %2 scaling not allowed
- 61012 Channel %1 block %2 different scaling on the plane
- 61013 Channel %1 block %2 basic settings were changed, program cannot be executed
- 61101 Channel %1 block %2 reference plane incorrectly defined
- 61102 Channel %1 block %2 no spindle direction programmed
- 61103 Channel %1 block %2 number of drillings is zero
- 61104 Channel %1 block %2 contour violation of slots/long holes
- 61105 Channel %1 block %2 cutter radius too large
- 61106 Channel %1 block %2 number or distance of circular elements
- 61107 Channel %1 block %2 first drilling depth incorrectly defined
- 61108 Channel %1 block %2 illegal values for parameters _RAD1 and _DP1
- 61109 Channel %1 block %2 parameter _CDIR incorrectly defined
- 61110 Channel %1 block %2 finishing allowance at the base > depth infeed
- 61111 Channel %1 block %2 infeed width > tool diameter
- 61112 Channel %1 block %2 tool radius negative
- 61113 Channel %1 block %2 parameter _CRAD for corner radius too large
- 61114 Channel %1 block %2 machining direction G41/G42 incorrectly defined
- 61115 Channel %1 block %2 approach or retract mode (straight line/circle/plane/space) incorrectly defined
- 61116 Channel %1 block %2 approach or retraction path = 0
- 61117 Channel %1 block %2 active tool radius <= 0
- 61118 Channel %1 block %2 length or width = 0
- 61119 Channel %1 block %2 nominal or core diameter incorrectly programmed
- 61120 Channel %1 block %2 internal/external thread type not defined
- 61121 Channel %1 block %2 number of teeth per cutting edge missing
- 61122 Channel %1 block %2 safety clearance on the plane incorrectly defined
- 61124 Channel %1 block %2 infeed width is not programmed
- 61125 Channel %1 block %2 technology selection in parameter _TECHNO incorrectly defined
- 61126 Channel %1 block %2 thread length too short
- 61127 Channel %1 block %2 transmission ratio of tapping axis incorrectly defined (machine data)
- 61128 Channel %1 block %2 dipping angle = 0 for dipping with oscillation or helix
- 61180 Channel %1 block %2 no name assigned to swivel data block, although MD $MN_MM_NUM_TOOL_CARRIER > 1
- 61181 Channel %1 block %2 NCK software version unsufficient (missing TOOLCARRIER functionality)
- 61182 Channel %1 block %2 name of swivel data block unknown
- 61183 Channel %1 block %2 retraction mode GUD7 _TC_FR beyond value range 0… 2
- 61184 Channel %1 block %2 no solution possible with current input angle values
- 61185 Channel %1 block %2 no or incorrect (min > max) rotary axis angle ranges assigned
- 61186 Channel %1 block %2 rotary axis vectors invalid –> Check installation and start-up of the swivel cycle CYCLE800
- 61188 Channel %1 block %2 no axis name for the 1st axis assigned -> Check installation and start-up of the swivel cycle CYCLE800
- 61200 Channel %1 block %2 too many elements in the machining block
- 61201 Channel %1 block %2 wrong sequence in the machining block
- 61202 Channel %1 block %2 no technology cycle
- 61203 Channel %1 block %2 no positioning cycle
- 61204 Channel %1 block %2 unknown technology cycle
- 61205 Channel %1 block %2 unknown positioning cycle
- 61210 Channel %1 block %2 block search element not found
- 61211 Channel %1 block %2 absolute reference missing
- 61212 Channel %1 block %2 wrong tool type
- 61213 Channel %1 block %2 circle radius too small
- 61214 Channel %1 block %2 no lead programmed
- 61215 Channel %1 block %2 raw dimension incorrectly programmed
- 61216 Channel %1 block %2 feed/tooth only possible with milling tools
- 61217 Channel %1 block %2 cutting speed for tool radius 0 programmed
- 61218 Channel %1 block %2 feed/tooth programmed, but number of teeth is zero
- 61222 Channel %1 block %2 plane infeed greater than the tool diameter
- 61223 Channel %1 block %2 approach path too short
- 61224 Channel %1 block %2 retract path too short
- 61225 Channel %1 block %2 swivel data block unknown
- 61226 Channel %1 block %2 swivel head cannot be exchanged
- 61230 Channel %1 block %2 tool probe diameter too small
- 61231 Channel %1 block %2 ShopMill program %3 cannot be executed, as it has not been tested by ShopMill
- 61232 Channel %1 block %2 loading of magazine tool not possible
- 61233 Channel %1 block %2: Thread inclination incorrectly defined
- 61234 Channel %1 block %2 ShopMill subroutine %4 cannot be executed, as it has not been tested by ShopMill
- 61235 Channel %1 block %2: ShopTurn program %4 cannot be executed, as it has not been tested by ShopTurn.
- 61236 Channel %1 block %2: ShopTurn subroutine %4 cannot be executed, as it has not been tested by ShopTurn.
- 61237 Channel %1 block %2: Retraction direction unknown. Manually retract tool!
- 61238 Channel %1 block %2: Machining direction unknown.
- 61239 Channel %1 block %2: Tool change point lies in the retraction area!
- 61240 Channel %1 block %2: Wrong feed type
- 61241 Channel %1 block %2: No retraction plane defined for this machining direction.
- 61242 Channel %1 block %2: Wrong machining direction
- 61243 Channel %1 block %2: Correct tool change point, tool tip is in retraction area!
- 61244 Channel %1 block %2: Thread lead change results in an undefined thread
- 61246 Channel %1 block %2: Safety clearance too small
- 61247 Channel %1 block %2: Blank radius too small
- 61248 Channel %1 block %2: Infeed too small
- 61249 Channel %1 block %2: Number of edges too small
- 61250 Channel %1 block %2: Key width/Edge length too small
- 61251 Channel %1 block %2: Key width/Edge length too large
- 61252 Channel %1 block %2: Chamfer/Radius too large
- 61253 Channel %1 block %2: No finishing allowance programmed
- 61254 Channel %1 block %2: Error when traversing to fixed stop
- 61255 Channel %1 block %2: Cut-off error: Tool breakage?
- 61301 Channel %1 block %2 measuring probe does not switch
- 61302 Channel %1 block %2 measuring probe collision
- 61303 Channel %1 block %2 safe area exceeded
- 61308 Channel %1 block %2 check measuring distance 2a
- 61309 Channel %1 block %2 check measuring probe type
- 61310 Channel %1 block %2 scale factor is active
- 61311 Channel %1 block %2 no D number is active
- 61316 Channel %1 block %2 center point and radius cannot be determined.
- 61332 Channel %1 block %2 change tool tip position
- 61338 Channel %1 block %2 positioning velocity is zero
- 61601 Channel %1 block %2 finished-part diameter too small
- 61602 Channel %1 block %2 tool width incorrectly defined
- 61603 Channel %1 block %2 groove form incorrectly defined
- 61604 Channel %1 block %2 active tool violates programmed contour
- 61605 Channel %1 block %2 contour incorrectly programmed
- 61606 Channel %1 block %2 contour processing error
- 61607 Channel %1 block %2 starting point incorrectly programmed
- 61608 Channel %1 block %2 wrong cutting edge position programmed
- 61609 Channel %1 block %2 form incorrectly defined
- 61610 Channel %1 block %2 no infeed depth programmed
- 61611 Channel %1 block %2 no intersection point found
- 61612 Channel %1 block %2 thread axis cutting not possible
- 61613 Channel %1 block %2 undercut position incorrectly defined
- 61800 Channel %1 block %2: External CNC system missing
- 61801 Channel %1 block %2: Wrong G code selected
- 61802 Channel %1 block %2: Wrong axis type
- 61803 Channel %1 block %2 programmed axis not present
- 61804 Channel %1 block %2: Progr. position exceeds reference point
- 61805 Channel %1 block %2: The value is absolutely and incrementally programmed
- 61806 Channel %1 block %2: Incorrect axis assignment
- 61807 Channel %1 block %2 wrong spindle direction programmed (active)
- 61808 Channel %1 block %2: The final drilling depth or individual drilling depth is missing
- 61809 Channel %1 block %2: Impermissible drilling position
- 61810 Channel %1 block %2: ISO-G code not possible
- 61811 Channel %1 block %2: Impermissible ISO axis name
- 61812 Channel %1 block %2: Value(s) in the external cycle call incorrectly defined
- 61813 Channel %1 block %2: GUD value incorrectly defined
- 61814 Channel %1 block %2: Polar coordinates not possible with cycle
- 61815 Channel %1 block %2: G40 not active
- 61816 Channel %1 block %2: axes are not at the reference point
- 61817 Channel %1 block %2: The axis coordinates are within the protection zone
- 61818 Channel %1 block %2: The axis area limit values are identical
- 62000 Channel %1 block %2:
- 62100 Channel %1 block %2 no drilling cycle active
- 62101 Channel %1 block %2: Incorrect cutting direction – G3 is generated
- 62103 Channel %1 block %2: The finishing allowance is not programmed
- 62105 Channel %1 block %2 number of columns or lines is zero
- 62180 Channel %1 block %2 no name assigned to swivel data block although machine data $MN_MM_NUM_TOOL_CARRIER > 1
- 62181 Channel %1 block %2 NCK software version unsufficient (missing TOOLCARRIER functionality)
- 62182 Channel %1 block %2: Load swivel head
- 62183 Channel %1 block %2 retraction mode GUD7 _TC_FR beyond value range 0…2
- 62184 Channel %1 block %2 no solution possible with current input angle values
- 62185 Channel %1 block %2 no end stop assigned to rotary axes
- 62186 Channel %1 block %2 illegal rotary axis vectors
- 62187 Channel %1 block %2 name of swivel data block unknown
- 62200 Channel %1 block %2: Start spindle
- 63000 Channel %1 block %2:
- 65000 Channel %1 block %2:
- 66000 Channel %1 block %2:
- 67000 Channel %1 block %2:
- 68000 Channel %1 block %2:
- 70000 Compile cycle alarm
- 75000 OEM alarm
- 75005 Channel %1 block %2 CLC: General programming error
- 75010 Channel %1 block %2 CLC_LIM value exceeds MD limit
- 75015 Channel %1 block %2 CLC(0) with active TOC
- 75016 Channel %1 block %2 CLC: orientation changed for TRAFOOF
- 75020 Channel %1 CLC position offset at lower limit %2
- 75021 Channel %1 CLC position offset at upper limit %2
- 75025 Channel %1 CLC stopped because sensor head has been touched
- 75050 Channel %1 wrong MD configuration, error code %2
- 75051 Channel %1 CC_COPON CC_COPOFF error code %2
- 75060 Channel %1 tolerance window exceeded axis %2
- 75061 Channel %1 coupling active axis %2
- 75062 Channel %1 axes not in standstill axis %2
- 75070 Channel %1 wrong machine data for collision protection %2
- 75071 Channel %1 collision monitoring axis %2
- 75100 Too many analog axes configured
- 75110 Axis %1 reached drift limit
- 75200 Channel %1 wrong MD configuration, %2 incorrect
- 75210 Channel %1 number of axes/axis assignment inconsistent
- 75250 Channel %1 tool parameters incorrect
- 75255 Channel %1 working area error
- 75260 Channel %1 block %2 tool parameters incorrect
- 75265 Channel %1 block %2 working area error
- 75270 Channel %1 tool parameters incorrect
- 75275 Channel %1 block %2 working area error
- 75451 Error with definition of setpoint switchover
- 75452 Axis %1 setpoint switchover not possible in the current state
- 75500 Channel %1 wrong configuration
- 75600 Channel %1 retrace support: wrong MD configuration. Error code %2
- 75601 Channel %1 block %2 invalid parameter in CC_PREPRE()
- 75605 Channel %1 retrace support: internal error, error code %2
- 75606 Channel %1 retraceable contour was shortened
- 75607 Channel %1 resynchronisation not possible
Pages: 1 2 3
3
Milling Cycles
3.16 Swiveling – CYCLE800 (SW 6.2 and higher)
3.16.6 Error messages
Explanation
Alarm source CYCLE800
Alarm number
61180
61181
61182
61183
61184
61185
61186
61187
61188
62180
62181
Typical display of the swivel angle to be set for a
manual rotary axis in CYCLE800
62180
3-258
Alarm text
«No name assigned to swivel data
record even though machine data
$MN_MM_NUM_TOOL_CARRIER > 1″
«NCK software version too old (no
TOOLCARRIER functionality)»
«Name of swivel data record unknown» See Swivel cycle start-up CYCLE800 à
«Retraction mode GUD7 _TC_FR
outside value range 0..2″
«No solution can be found with current
angle inputs»
«Rotary axis angle ranges incorrect
(min>max) or not defined»
«Invalid rotary axis vectors»
«Block search computation end of block
not valid for SWIVEL»
«No axis name
1st rotary axis declared»
«Set rotary axes x.x [deg]»
«Set rotary axes x.x [deg]»
«Set rotary axes B: 32.5 [deg]»
Explanation, remedy
No name assigned to swivel data record
even though several swivel data records
exist
($MN_MM_NUM_TOOL_CARRIER>0) or
no swivel data record defined
($MN_MM_NUM_TOOL_CARRIER=0)
TOOLCARRIER functionality as from
NCU 6.3xx
Kinematics Name (swivel data record)
See Swivel cycle start-up CYCLE800 à
Retraction;
1st transfer parameter CYCLE800(x,…) is
faulty >2
Check start-up of swivel cycle
CYCLE800
Swivel cycle start-up CYCLE800:
Rotary axis vector V1 or V2 not entered
or incorrect
Select block search with calculation
contour
Swivel cycle start-up CYCLE800: no
entry under rotary axis 1 identifier
Angles to be set for manual rotary axes
Angle to be set for manual rotary axis
SINUMERIK 840D/840Di/810D Programming Guide Cycles (PGZ) – 11.02 Edition
3
12.97
11.02
© Siemens AG, 2002. All rights reserved
Перейти к контенту
Значит,начну с Sander,мануалы на фирме SIEMENS выкладываются,чтобы заказчик примерно представлял,что и какую технику он может заказать.Как и в других областях,авторские права разработчиков этой техники строго охраняются.Существует специальная служба,которая регулярно шерстит «гугль»и мало не покажется,если произойдет утечка;-адвокаты там звери!
А теперь,по теме.Прежде чем выложить процедуру перезаписи NCK на SINUMERIK-810D,840D,хочу сразу предупредить,что переинсталляция NCK,шаг крайний и ответственный.Это крайняя мера и прибегать к ней нужно,если все остальные способы оказались неэффективны.
Добавлено 06-09-2009 19:52
Итак,если решились,то мы должны работать с ключом красного цвета,т.е. с первым уровнем доступа.Переведите его в предпоследнюю позицию.Дальше;
1.В окне «STARTAP»,введите ,удерживая кнопку «^» непрерывно ,код «S U N R I S E»
2.На SIMODRIVE-611,установить переключатель «S4» в положение «2»
Попробуйте сейчас прописать программы»PLC»,-это вариант «малой крови»,без вышибания информации ядра NCK
Если не пошло,тогда нет выбора и нужно инсталлировать NCK и PLC полностью.
Без наличия диска с программами NCK,PLC,SPF,MPF не начинайте инсталляцию!!!
Добавлено 06-09-2009 20:14
Теперь подробно,как выполняется процедура полного обнуления памяти.Все операции производятся на SIMODRIVE-611
1.S4—>»3″,выключить и включить машину
2.S4—>»4″,держать не более 3 секунд
3.S4—>»0″
4.S3—>»1″-обнуление регистров
5.S3—>»0″
6.S3—>»1″,выключaем и с задержкой 10 с. включaем машину.
7.S3—>»0″
Если, после обнуления,горят краcные лампочки «RF» и «RS»,то
8.S4—>»3″ с задержкой 3 с. неcколько раз повторить.
9.S4—>»0″-пишем параметры ядра NCK
10.S4—>»2″-пишем программы PLC
Добавлено 06-09-2009 20:25
Еcли обнуление и запись прошли без накладок,горят две зеленые лампочки.Теперь осталось:
1.Проверить наличие осей
2.Обязательно,перед «REFERENCE POINT» удалить код доступа и сменить красный ключ!
ВНИМАНИЕ! В процессе перезаписи возможно самопроизвольное изменение параметров интерфейса обмена данными,поэтому не надо паниковать,если запись не пошла с первого раза.Подкорректируйте параметры в окне «SERVICE».
Только что, David123 сказал:
Уважаемый @nein !
1) Насколько я понял, Вы умеете обращаться с архивами, первым делом сохраните текущий архив NC.
2) Ошибку 700004 — выдает электроавтоматика станка. Она должна быть описана в Руководстве по станку. Что там сказано?
3) Эта ошибка всегда выводится или ранее станок работал, выдавал готовую продукцию, но произошли какие-то обстоятельства, после чего происходит описываемое.
4) Эта ошибка выводится сразу после первоначальной загрузки системы или какие-то действия производятся на станке? Нет ли в строке вывода ошибки, сразу после номера 700004 символа «стрелка вниз». Это признак — одновременно появились несколько ошибок или сообщений. В области ДИАГНОСТИКА можно найти полный их список. Сделайте их фото.
5) Есть ли у Вас проект (не архив) электроавтоматики станка?
Уважаемый@David123 , большое спасибо, что пытаетесь помочь.
1) Текущий архив NC я сразу сохранил.
2) Там сказано — замените предохранитель или включите автомат.
3) Начну с самого начала. Мы купили станок в Турции. Когда он приехал, он включился, но выдавал другие ошибки. Включался свет в рабочей зоне от кнопки. Выяснилось, что там не было заглушки на разъёме подключения податчика прутка. Я стал ставить заглушку, но в процессе перевозки или погрузки станка этот разъём был сломан. В результате там что-то перемкнулось, и теперь выпадает такая ошибка про предохранитель. Разъём мы заменили, цепи прозвонили — всё нормально. Но теперь ошибка не уходит. Свет не включается.
Теперь вернусь к автоматам. Все цепочки — нормальные. На фотографии 1 на модуле 9А3 горят светодиоды B2.7 и B3.0 — т.е. все автоматы нормальные. На фотографии 2 на блоке питания 9А1 постоянно горит красный светодиод FAULT. На фотографии 1 видно, что горят светодиоды на модулях 9А3 и 9А4 (это если мы правильно понимаем, входные цепи для 9А1) и не горят на выходном модуле 9А5. Сам блок 9А1 мы меняли (брали точно такой же с соседнего рабочего станка) — ничего не менялось. X3/IN — это связь с PLC.
4) Ошибка выпадает сразу при загрузке. Я разговаривал с сервисником Шпиннера из Болгарии, он сказал, что все остальные ошибки — это производные от 700004. Завтра сделаю фото области «диагностика».
5) Нет, проекта у меня нет.
Siemens Sinumerik 840D alarm list (840D/840Di/810D and similar controls), for cnc machinists and maintenance personnel who work on cnc machines with Sinumerik cnc controls.
Siemens Sinumerik Alarms
Sinumerik 840D Alarm List
- 1000 System error %1
- 1001 System error %1
- 1002 System error %1
- 1003 Alarm pointer for this self-clearing alarm %1 is zero
- 1004 Alarm reaction to NCK alarm incorrectly configured
- 1005 Operating system error %1 parameter %2 %3 %4
- 1010 Channel %1 system error %2 action %3
- 1011 Channel %1 %3 %4 system error %2
- 1012 Channel %1 system error %2 %3 %4
- 1013 Channel %1 system error %2
- 1014 Channel %1 system error %2
- 1015 Channel %1 axis %2 system error %3
- 1016 Channel %1 axis %2 system error %3
- 1017 Channel %1 axis %2 system error %3
- 1018 Floating point arithmetic error in channel %1 task %2 station %3 FPU state %4 %4
- 1019 Floating point arithmetic error at address %3 in channel %1 task %2 FPU state %4
- 1030 System error in link module error code %1 error type %2
- 1031 Link module generated an unspecified error %1 NCU %2 %3 %4
- 1100 No valid firmware
- 1160 Assertion failed in %1: %2
- 2000 PLC sign-of-life monitoring
- 2001 PLC has not started up
- 2100 NCK battery warning threshold reached
- 2101 NCK battery alarm
- 2102 NCK battery alarm
- 2110 NCK temperature alarm
- 2120 NCK fan alarm
- 2130 5V/24V encoder or 15V D/A converter under voltage
- 2140 The actual service switch position forces a SRAM to be cleared at the next Power On (general reset active)
- 2190 Hardware plug-in module for communication with the digitizer missing
- 2192 No NCU link module exists, MD %1 reset
- 2193 “Safety Integrated” is not available for link axis %1.
- 2195 Channel %1 axis %2 high-speed punching/nibbling not possible via link
- 2196 Link axis active and $MN_MM_SERVO_FIFO_SIZE != %1
- 2900 Reboot is delayed
- 3000 Emergency stop
- 3001 Internal emergency stop
- 4000 Channel %1 machine data %2[%3] has gap in axis assignment
- 4001 Channel %1 axis %2 defined for more than one channel via machine data %3
- 4002 Channel %1 machine data %2[%3] assigns an axis not defined in channel
- 4003 Axis %1 incorrect assignment of master channel in machine data %2
- 4004 Channel %1 machine data %2 axis %3 defined repeatedly as geometry axis
- 4005 Maximum number of axes in channel %1 exceeded. Limit %2
- 4007 Axis %1 incorrect assignment of master NCU in machine data %2
- 4010 Invalid identifier used in machine data %1[%2]
- 4011 Channel %1 invalid identifier used in machine data %2[%3]
- 4012 Invalid identifier used in machine data %1[%2]
- 4013 Invalid NCU link configuration by machine data %1 = %2 , on NCU_1 = %3
- 4014 Axis %1 defined several times in %2
- 4016 Axis %1 already used by NCU %2
- 4017 Axis container %1, location %2 already used by NCU %3
- 4018 Axis container %1, location %2 not used by any channel
- 4019 Axis container %1 advance not allowed with current status of NCU %2
- 4020 Identifier %1 used several times in machine data %2
- 4021 Channel %1 identifier %2 used several times in machine data %3
- 4022 Axis container %3 switch not allowed: ext. zero offset active channel %1 axis %2
- 4023 Axis container %1 switch not allowed, axis container %2 switch active
- 4024 Invalid axis configuration due to missing axis container machine data
- 4025 Axis container %3 switch not allowed: master/slave active channel %1 axis %2
- 4026 Machine data %1[%2], link axis NC%3_AX%4 not used by any channel
- 4027 Notice: MD %1 was also changed for the other axes of axis container %2
- 4028 Notice! The axial MDs of the axes of the axis containers were matched.
- 4029 Notice: the axial MDs in axis container %1 will be matched on the next power-up
- 4030 Channel %1 axis identifier missing in machine data %2[%3]
- 4031 Channel %1 link axis %2 defined for more than one channel in machine data %3
- 4032 Channel %1 wrong identifier for facing axis in %2
- 4033 Notice: NCU link communication still not connected
- 4034 Local link axis %1 is not allowed for different interpolation cycle time = %2/%3
- 4035 Interpolation cycle from NCU%1 = %2 does not match NCU%3 = %4
- 4036 Wrong NCU link configuration by MD %1
- 4040 Channel %1 axis identifier %2 not consistent with machine data %3
- 4045 Channel %1 conflict between machine data %2 and machine data %3
- 4050 NC code identifier %1 cannot be reconfigured to %2
- 4060 Standard machine data loaded
- 4062 Backup data loaded
- 4065 Buffered memory was restored from backup medium (potential loss of data!)
- 4066 Buffered memory of FFS restored from backup medium (potential loss of data!)
- 4070 Normalizing machine data has been altered
- 4073 Compile cycle functions define machine data number %1 several times
- 4075 Machine data %1 (and maybe others) not altered due to missing permission level %2
- 4076 %1 Machine data could not be altered with permission level %2
- 4077 New value %1 of MD %2 not set. Requested %3 bytes too much %4 memory.
- 4080 Incorrect configuration of indexing axis in MD %1
- 4090 Too many errors during power-up
- 4100 System cycle time/scan time divider corrected for digital drive
- 4102 Default values for drive cycle times differ
- 4110 IPO factor increased to %1
- 4111 PLC cycle increased to %1 ms
- 4112 Servo cycle changed to %1 ms
- 4113 Sysclock cycle changed to %1 ms
- 4114 Error in DP cycle of SDB1000
- 4115 Time ratio communication to Ipo changed to %1
- 4150 Channel %1 invalid M function sub program call configured
- 4152 Illegal configuration of the “Block display with absolute values” function
- 4160 Channel %1 invalid M function number configured for spindle switchover
- 4170 Invalid M function number for channel synchronisation assigned
- 4180 Invalid M function number assigned to enable ASUP
- 4181 Channel %1 invalid assignment of an M auxiliary function number
- 4182 Channel %1 invalid M auxiliary function number in %2%3, MD reset
- 4183 Channel %1 M auxiliary function number %2 used several times (%3 and %4)
- 4184 Channel %1 illegally predefined auxiliary function in %2%3, MD reset
- 4185 Channel %1 illegal auxiliary function configured %2 %3 %4
- 4200 Channel %1 geometry axis %2 must not be declared a rotary axis
- 4210 Channel %1 spindle %2 declaration as rotary axis missing
- 4215 Channel %1 spindle %2 declaration as modulo axis missing
- 4220 Channel %1 spindle %2 declared repeatedly
- 4225 Channel %1 axis %2 declaration as rotary axis missing
- 4230 Channel %1 data alteration from external not possible in current channel state
- 4240 Runtime overflow for IPO cycle or position controller cycle, IP %1
- 4250 FastPlcCom functionality not available
- 4252 PLCIO read error: %1
- 4254 PLCIO write error: %1
- 4260 Machine data %1 illegal
- 4270 Machine data %1 assigns not activated NCK input/output byte %2
- 4275 Machine data %1 and %2 both assign the same NCK output byte no. %3 several times
- 4280 Assignment of NCK input/output byte via MD %1[%2] does not match hardware configuration
- 4282 Hardware of external NCK outputs assigned repeatedly
- 4285 Error on terminal block %1, error code %2
- 4290 Local P-bus sign-of-life monitoring
- 4291 Module in local P-bus slot %1 error codes %2 %3 %4 %2 %3 %4
- 4300 Declaration in MD %1 is not allowed for geometry axis/spindle %2.
- 4310 Declaration in MD %1 index %2 is not allowed.
- 4320 Axis %1 function %2 %3 and %4 not allowed
- 4334 Channel %1 The amount of fine correction in parameter %2 of the orientable toolholder %3 is too large
- 4336 Channel %1 orientable toolholder no. %2 for orientation transformation %3 does not exist
- 4338 Channel %1 invalid transformation type ‘%2’ in toolholder %3 for orientation transformer %4
- 4340 Channel %1 block %2 invalid transformation type in transformation no. %3
- 4341 Channel %1 block %2 no data set available for transformation no. %3
- 4342 Channel %1 invalid machine data for general 5-axis transformation error no. %2
- 4343 Channel %1 attempt made to change the machine data of an active transformation.
- 4345 Channel %1 invalid configuration in chained transformation no.%2
- 4346 Channel %1 invalid geoaxis assignment in machine data %2[%3]
- 4347 Channel %1 invalid channel axis assignment in machine data %2[%3]
- 4350 Channel %1 axis identifier %2 machine data %3 not consistent with machine data %4
- 4400 MD alteration will cause reorganisation of buffered memory (loss of data!)
- 4502 Channel %1 anachronism %2(%3) -> %4
- 5000 Communication job not executable %1
- 6000 Memory reorganized using standard machine data
- 6010 Channel %1 data block %2 not or not completely created, error code %3
- 6020 Machine data have been altered – now memory is reorganized
- 6030 Limit of user memory has been adapted
- 6035 Instead of %1 KB the system has only %2 KB of free user memory of type “%3”
- 6100 Error while creating %1, error number %2 %3
- 6401 Channel %1 tool change not possible: Empty location for tool %2 Duplo no. %3 on magazine %4 not available.
- 6402 Channel %1 tool change not possible. Magazine no. %2 not available
- 6403 Channel %1 tool change not possible. Magazine location number %2 on magazine %3 not available.
- 6404 Channel %1 tool change not possible. Tool %2 not available or not usable
- 6405 Channel %1 command %2 has invalid PLC acknowledge parameter %3 – identifier %4
- 6406 Channel %1 PLC acknowledge for command %2 is missing
- 6407 Channel %1 tool %2 cannot be placed in magazine %3 on location %4.Invalid definition of magazine!
- 6410 TO unit %1 tool %2 / Duplo no. %3 has reached its pre warning limit with D = %4
- 6411 Channel %1 tool %2 / Duplo no. %3 has reached its prewarning limit with D = %4
- 6412 TO unit %1 tool %2 / Duplo no. %3 has reached its monitoring limit with D = %4
- 6413 Channel %1 tool %2 / Duplo no. %3 has reached its monitoring limit with D = %4
- 6421 Channel %1 tool move not possible. Empty location for tool %2 Duplo no. %3 on magazine %4 not available.
- 6422 Channel %1 tool move not possible. Magazine no. %2 not available.
- 6423 Channel %1 tool move not possible. Location %2 on magazine %3 not available.
- 6424 Channel %1 tool move not possible. Tool %2 not available/not usable.
- 6425 Channel %1 tool %2 cannot be placed in magazine %3 on location %4. Invalid definition of magazine!
- 6430 Workpiece counter: overflow in table of monitored cutting edges.
- 6431 Function not allowed. Tool management/monitoring is not active.
- 6432 Function not executable. No tool assigned to tool holder/spindle
- 6433 Channel %1 block %2 %3 not available with tool management
- 6434 Channel %1 block %2 NC command SETMTH not allowed because tool holder function not active
- 6441 Writing of $P_USEKT not allowed.
- 6442 Channel %1 function not executable. No tool assigned to desired magazine/magazine location %2.
- 6450 Channel %1 tool change not possible. Invalid magazine location no. %2 in buffer magazine
- 6451 Channel %1 tool change not possible. No buffer magazine defined.
- 6452 Channel %1 tool change not possible. Tool holder/spindle number = %2 not defined.
- 6453 Channel %1 tool change not possible. No assignment between toolholder/spindle no. = %2 and buffer magazine location %3
- 6454 Channel %1 tool change not possible. No distance relation available.
- 6500 NC memory full
- 6510 Too many part programs in the NC memory
- 6520 The value of the machine data %1%2 is too low
- 6530 Too many files in directory
- 6540 Too many directories in the NC memory
- 6550 Too many subdirectories
- 6560 Data format not allowed
- 6570 NC memory full
- 6580 NC memory full
- 6600 NC card memory is full
- 6610 Too many files open on NC card
- 6620 NC card has incorrect format
- 6630 NC card hardware is defective
- 6640 NC card is not inserted
- 6650 Write protection of NC card is active
- 6660 ‘Flash File System’ option is not set
- 6670 NC card read active
- 6671 NC card write active
- 6690 Cycles from NC card cannot be copied to the passive file system.
- 6691 Cycles from the passive file system cannot be saved on the NC card
- 6692 Cycle %1 lost
- 6693 File %1 lost
- 6698 Unknown NC card (%1/%2). Writing not possible.
- 6700 Channel %1 value of the machine data %2%3 is too low
- 7000 Too many compile cycle alarms defined
- 7010 Range of MMC alarm numbers for compile cycles exceeded
- 7020 Compile cycle alarm number has not been defined
- 7100 Compile cycles VDI area: %1 byte for inputs and %2 byte for outputs. Maximum %3 bytes available.
- 7200 Problem with externally linked compile cycle %1 %2
- 7201 Assertion error in %1 line %2
- 7202 Missing option bit for %1: %2
- 8000 Channel %1 option ‘user interrupt programs’ not set
- 8010 Option ‘activation of more than %1 axes’ not set
- 8020 Option ‘activation of more than %1 channels’ not set
- 8021 Option ‘activation of more than %1 mode groups’ not set
- 8022 Option ‘activation of more than %1KB SRAM’ not set
- 8030 Channel %1 block %2 option ‘interpolation of more than 4 axes’ not set
- 8032 Option ‘activation of more than %1 link axes’ not set
- 8034 Option ‘activation of axis containers’ not set
- 8036 Option: it is not allowed to set different IPO cycles or position control cycles with NCU link.
- 8038 Option ‘activation of more than %1 lead link axes’ not set
- 8040 Machine data %1 reset, corresponding option is not set
- 8041 Axis %1: MD %2 reset, corresponding option not sufficient
- 8044 Option for IPO cycle time %1 ms not set
- 8045 Option for selected cycle settings not set
- 8080 %1 options are activated without setting the license key
- 8081 %1 options are activated that are not licensed by the license key
- 8082 The license key was entered three times, Power On required before next try.
- 8098 Invalid combination of options (%1)
- 8100 Channel %1 block %2: function not possible
- 10203 Channel %1 NC start without reference point
- 10207 Channel %1 error when selecting or deselecting the digitize function
- 10208 Channel %1 continue program with NC start
- 10209 Channel %1 internal NC stop after block search
- 10222 Channel %1 inter-channel communication not possible
- 10223 Channel %1: Command %2 is already occupied
- 10225 Channel %1: command denied
- 10299 Channel %1 Auto-Repos function is not enabled
- 10600 Channel %1 block %2 auxiliary function during thread cutting active
- 10601 Channel %1 block %2 zero velocity at block end point during thread cutting
- 10604 Channel %1 block %2 thread lead increase too high
- 10605 Channel %1 block %2 thread lead decrease too high
- 10607 Channel %1 block %2 thread with frame not executable
- 10610 Channel %1 axis %2 not stopped
- 10620 Channel %1 block %3 axis %2 at software limit switch %4
- 10621 Channel %1 axis %2 rests on software limit switch %3
- 10630 Channel %1 block %2 axis %3 at working area limit %4
- 10631 Channel %1 axis %2 rests at working area limit %3
- 10650 Channel %1 axis %2 incorrect gantry machine data, error code %3
- 10651 Channel %1 illegal gantry configuration. Error code %2
- 10652 Channel %1 axis %2 gantry warning threshold exceeded
- 10653 Channel %1 axis %2 gantry error threshold exceeded
- 10654 Channel %1 waiting for synchronization start of gantry group %2
- 10655 Channel %1 synchronization of gantry group %2 in progress
- 10656 Channel %1 axis %2 gantry alarm not yet used
- 10700 Channel %1 block %2 NCK protection zone %3 violated during automatic or MDA mode
- 10701 Channel %1 block %2 channel-specific protection zone %3 violated during automatic or MDA mode
- 10702 Channel %1 NCK protection zone %2 violated during manual mode
- 10703 Channel %1 channel-specific protection zone %2 violated during manual mode
- 10704 Channel %1 block %2 protection zone monitoring is not guaranteed
- 10706 Channel %1 NCK protection zone %2 reached with axis %3 during manual mode
- 10707 Channel %1 channel-specific protection zone %2 reached with axis %3 during manual mode
- 10710 Channel %1 block %2 conflict with centre less grinding
- 10720 Channel %1 block %3 axis %2 software limit switch %4
- 10721 Channel %1 block %3 axis %2 software limit switch %4
- 10730 Channel %1 block %3 axis %2 working area limitation %4
- 10731 Channel %1 block %3 axis %2 working area limitation %4
- 10740 Channel %1 block %2 too many empty blocks in WAB programming
- 10741 Channel %1 block %2 direction reversal with WAB infeed motion
- 10742 Channel %1 block %2 WAB distance invalid or not programmed
- 10743 Channel %1 block %2 WAB programmed several times
- 10744 Channel %1 block %2 no valid WAB direction defined
- 10745 Channel %1 block %2 WAB end position not clear
- 10746 Channel %1 block %2 block search stop for WAB
- 10747 Channel %1 block %2 retraction direction not defined for WAB
- 10748 Channel %1 block %2 illegal retract plane with WAB
- 10750 Channel %1 block %2 tool radius compensation activated without tool number
- 10751 Channel %1 block %2 danger of collision due to tool radius compensation
- 10752 Channel %1 block %2 overflow of local block buffer with tool radius compensation
- 10753 Channel %1 block %2 selection of the tool radius compensation only possible in linear block
- 10754 Channel %1 block %2 deselection of the tool radius compensation only possible in linear block
- 10755 Channel %1 block %2 selection of the tool radius compensation via KONT not possible at the current starting point
- 10756 Channel %1 block %2 deselection of the tool radius compensation via KONT not possible at the programmed end point
- 10757 Channel %1 block %2 changing the compensation plane while tool radius compensation is active not possible
- 10758 Channel %1 block %2 curvature radius with variable compensation value too small
- 10759 Channel %1 block %2 path is parallel to tool orientation
- 10760 Channel %1 block %2 helical axis is not parallel to tool orientation
- 10761 Channel %1 block %2 tool radius compensation for ellipse with more than one revolution not possible
- 10762 Channel %1 block %2 too many empty blocks between two traversing blocks with active tool radius compensation
- 10763 Channel %1 block %2 path component of the block in the compensation plane becomes zero
- 10764 Channel %1 block %2 discontinuous path with active tool radius compensation
- 10765 Channel %1 block %2 3D tool radius compensation not possible
- 10766 Channel %1 illegal change of surface orientation between block %2 and block %3
- 10767 Channel %1 block %2 processing with tilt angle unequal 0 not possible
- 10768 Channel %1 block %2 illegal tool orientation with 3D tool radius compensation
- 10769 Channel %1 block %2 Illegal surface normal vector with 3D tool radius compensation
- 10770 Channel %1 block %2 change of corner type due to change of orientation with active tool radius compensation
- 10771 Channel %1 block %2 overflow of local block buffer due to orientation smoothing
- 10772 Channel %1 block %2 illegal orientation change when activating or deactivating 3D face cutting
- 10773 Channel %1 illegal tool orientation in block %2 at inside corner with block %3
- 10774 Channel %1 illegal tool dimensions with face cutting in block %2
- 10775 Channel %1 illegal tool change with face cutting in block %2
- 10776 Channel %1 block%2 axis %3 must be geometry axis if tool radius compensation is active
- 10777 Channel %1 block %2 tool radius compensation: too many blocks with suppression of compensation
- 10778 Channel %1 block %2 preprocessing stop with active tool radius compensation
- 10779 Channel %1 block %2 preprocessing stop with active tool radius compensation
- 10780 Channel %1 block %2 preprocessing stop with active tool radius compensation
- 10781 Channel %1 block %2 illegal orientation of involute with tool radius compensation
- 10782 Channel %1 block %2 illegal curve type with tool radius compensation
- 10783 Channel %1 block %2 tool radius compensation type requires orientation transformation
- 10784 Channel %1 block %2 illegal tool for tool radius compensation with constraint surface
- 10790 Channel %1 block %2 plane change during linear programming with angles
- 10791 Channel %1 block %2 invalid angle during linear programming
- 10792 Channel %1 block %2 illegal interpolation type during linear programming with angles
- 10793 Channel %1 block %2 second block missing during linear programming with angles
- 10794 Channel %1 block %2 angle specification missing in second block during linear interpolation with angles
- 10795 Channel %1 block %2 end point specification during angle programming contradictory
- 10800 Channel %1 block %3 axis %2 is not a geometry axis
- 10805 Channel %1 block %2 repositioning after switch of geometry axes or transformation
- 10810 Channel %1 block %2 master spindle not defined
- 10820 Channel %1 rotary axis/spindle %2 not defined
- 10860 Channel %1 block %2 feedrate not programmed
- 10861 Channel %1 block %3 velocity of positioning axis %2 is zero
- 10862 Channel %1 block %2 master spindle also used as path axis
- 10870 Channel %1 block %2 facing axis not defined
- 10880 Channel %1 block %2 too many empty blocks between two traversing blocks when inserting chamfers or radii
- 10881 Channel %1 block %2 overflow of local block buffer when inserting chamfers or radii
- 10882 Channel %1 block %2 activation of chamfers or radii (non-modal) without traversing movement in the block
- 10883 Channel %1 block %2 chamfer or fillet has to be reduced
- 10890 Channel %1 block %2 overflow of local block buffer when calculating splines
- 10891 Channel %1 block %2 multiplicity of node is greater than its order
- 10900 Channel %1 block %2 no S value programmed for constant cutting speed
- 10910 Channel %1 block %2 excessive velocity of one path axis
- 10911 Channel %1 block %2 transformation prohibits to traverse the pole
- 10912 Channel %1 block %2 preprocessing and main run might not be synchronized
- 10913 Channel %1 block %2 negative feed profile is ignored
- 10914 Movement not possible while transformation active – in channel %1, block %2
- 10930 Channel %1 block %2 interpolation type not allowed in stock removal contour
- 10931 Channel %1 block %2 incorrect stock removal contour
- 10932 Channel %1 block %2 preparation of contour has been restarted
- 10933 Channel %1 block %2 contour program does not contain enough contour blocks
- 10934 Channel %1 block %2 array for contour segmentation is set too small
- 10940 Channel %1 block %2 curve table %3: delete/overwrite not possible
- 10941 Channel %1 block %2 curve table %3: NC memory full
- 10942 Channel %1 block %2 curve table %3: illegal instruction during definition
- 10943 Channel %1 block %2 curve table %3: direction reversal of lead value in the block not allowed
- 10944 Channel %1 block %2 curve table %3: illegal transformation
- 10945 Channel %1 block %2 curve table %3: illegal coupling of axes
- 10946 Channel %1 block %2 curve table %3: no contour defined
- 10947 Channel %1 block %2 curve table %3: contour not continuous
- 10948 Channel %1 block %2 curve table %3: position jump at end of period
- 10949 Channel %1 block %2 curve table %3: missing master axis motion
- 10950 Channel %1 calculation of arc length function too inaccurate
- 10951 Channel %1 block %2 curve table %3: following value period is zero
- 10955 Channel %1 block %2 curve table %3: missing master axis motion
- 10956 Channel %1 block %2 curve table %3: NC memory limit DRAM reached
- 10960 Channel %1 block %2 COMPCURV/COMPCAD and radius compensation cannot be used simultaneously
- 10961 Channel %1 block %2 maximum cubic polynomials are allowed on active radius compensation.
- 10962 Channel %1 block %2 function %3 not possible with path correction
- 12000 Channel %1 block %2 address %3 programmed repeatedly
- 12010 Channel %1 block %2 address %3 address type programmed too often
- 12020 Channel %1 block %2 illegal address modification
- 12030 Channel %1 block %2 invalid parameter or data type in %3
- 12040 Channel %1 block %2 expression %3 is not of data type ‘AXIS’
- 12050 Channel %1 block %2 DIN address %3 not configured
- 12060 Channel %1 block %2 same G group programmed repeatedly
- 12070 Channel %1 block %2 too many syntax-defining G functions
- 12080 Channel %1 block %2 syntax error in text %3
- 12090 Channel %1 block %2 unexpected parameter %3
- 12100 Channel %1 block %2 number of passes %3 not permissible
- 12110 Channel %1 block %2 block syntax cannot be interpreted
- 12120 Channel %1 block %2 G function not separately programmed
- 12130 Channel %1 block %2 illegal tool orientation
- 12140 Channel %1 block %2 functionality %3 not implemented
- 12150 Channel %1 block %2 operation %3 not compatible with data type
- 12160 Channel %1 block %2 range of values exceeded
- 12170 Channel %1 block %2 identifier %3 defined repeatedly
- 12180 Channel %1 block %2 illegal chaining of operators %3
- 12190 Channel %1 block %2 variable of type ARRAY has too many dimensions
- 12200 Channel %1 block %2 symbol %3 cannot be created
- 12210 Channel %1 block %2 string %3 too long
- 12220 Channel %1 block %2 binary constant %3 in string too long
- 12230 Channel %1 block %2 hexadecimal constant %3 in string too long
- 12240 Channel %1 block %2 tool orientation %3 defined repeatedly
- 12250 Channel %1 block %2 nested macro %3 not possible
- 12260 Channel %1 block %2 too many initialization values specified %3
- 12261 Channel %1 block %2 initialization of %3 not allowed
- 12270 Channel %1 block %2 macro identifier %3 already defined
- 12280 Channel %1 block %2 maximum macro length %3 exceeded
- 12290 Channel %1 block %2 arithmetic variable % 3 not defined
- 12300 Channel %1 block %2 call-by-reference parameter missing on subroutine call %3
- 12310 Channel %1 block %2 axis parameter missing on procedure call %3
- 12320 Channel %1 block %2 parameter %3 is no variable
- 12330 Channel %1 block %2 type of parameter %3 incorrect
- 12340 Channel %1 block %2 number of parameters too high %3
- 12350 Channel %1 block %2 parameter %3 no longer possible
- 12360 Channel %1 block %2 dimension of parameter %3 incorrect
- 12370 Channel %1 block %2 range of values %3 not permissible
- 12380 Channel %1 block %2 maximum memory capacity reached
- 12390 Channel %1 block %2 initialization value %3 cannot be converted
- 12400 Channel %1 block %2 field %3 element does not exist
- 12410 Channel %1 block %2 incorrect index type for %3
- 12420 Channel %1 block %2 identifier %3 too long
- 12430 Channel %1 block %2 specified index is invalid
- 12440 Channel %1 block %2 maximum number of formal arguments exceeded
- 12450 Channel %1 block %2 label defined twice
- 12460 Channel %1 block %2 maximum number of symbols exceeded with %3
- 12470 Channel %1 block %2 G function %3 is unknown
- 12475 Channel %1 block %2 invalid G function number %3 programmed
- 12480 Channel %1 block %2 subroutine %3 already defined
- 12490 Channel %1 block %2 access permission level %3 is not valid
- 12500 Channel %1 block %2 in this module %3 is not possible
- 12510 Channel %1 block %2 too many machine data %3
- 12520 Channel %1 block %2 too many tool parameters %3
- 12530 Channel %1 block %2 invalid index for %3
- 12540 Channel %1 block %2 Block is too long or too complex
- 12550 Channel %1 block %2 name %3 not defined or option not installed
- 12552 Channel %1 block %2 tool/magazine OEM parameter not defined. Option not set.Option not set.
- 12560 Channel %1 block %2 programmed value %3 exceeds allowed limits
- 12570 Channel %1 block %2 too many motion synchronous actions in %3
- 12571 Channel %1 block %2 %3 not permissible for motion synchronous action
- 12572 Channel %1 block %2 %3 only permissible for motion synchronous action
- 12580 Channel %1 block %2 %3 not permissible for assignment in motion synchronous action
- 12581 Channel %1 block %2 invalid read access to %3 while in motion synchronous action
- 12582 Channel %1 block %2 field index %3 incorrect
- 12583 Channel %1 block %2 variable %3 no system variable
- 12584 Channel %1 block %2 variable %3 cannot be read synchronously with motion
- 12585 Channel %1 block %2 variable %3 cannot be changed synchronously with motion
- 12586 Channel %1 block %2 motion synchronous action: type conflict in variable %3
- 12587 Channel %1 block %2 motion synchronous action: operation/function %3 not allowed
- 12588 Channel %1 block %2 motion synchronous action: address %3 not allowed
- 12589 Channel %1 block %2 motion synchronous action: variable %3 not allowed with modal ID
- 12590 Channel %1 block %2 global user data cannot be created
- 12600 Channel %1 block %2 invalid line checksum
- 12610 Channel %1 block %2 accessing single character with call-by-reference parameter not possible %3
- 12620 Channel %1 block %2 accessing this variable as single character not possible
- 12630 Channel %1 block %2 skip ID/label in control structure not allowed
- 12640 Channel %1 block %2 invalid nesting of control structures
- 12641 Channel %1 block %2 maximum nesting depth of control structures exceeded
- 12650 Channel %1 block %2 axis identifier %3 different in channel %4
- 12660 Channel %1 block %2 motion synchronous action: variable %3 reserved for motion synchronous actions and technology cycles
- 12661 Channel %1 block %2 technology cycle %3: no further subprogram call possible
- 12700 Channel %1 block %2 contour definition programming not allowed as modal sub program is active
- 12701 Channel %1 block %2 illegal interpolation type for contour definition active
- 12710 Channel %1 block %2 illegal language element in external language mode
- 12720 Channel %1 block %2 program number for macro call (G65/G66) missing
- 12722 Channel %1 block %2 multiple ISO_2/3 macro or cycle calls in the block
- 12724 Channel %1 block %2 no radius programmed for cylinder interpolation activation/deactivation
- 12726 Channel %1 block %2 illegal plane selection with parallel axes
- 12728 Channel %1 block %2 distance for double turret not set
- 12730 Channel %1 block %2 no valid transformation machine data parametrized
- 12740 Channel %1 block %2 modal macro call %3 not possible
- 14000 Channel %1 block %2 illegal end of file
- 14001 Channel %1 block %2 illegal end of block
- 14009 Channel %1 block %2 illegal program path %3
- 14010 Channel %1 block %2 invalid default parameter in subroutine call
- 14011 Channel %1 block %2 program %3 not existing or will be edited
- 14012 Channel %1 block %2 maximum subroutine level exceeded
- 14013 Channel %1 block %2 number of subroutine passes invalid
- 14014 Channel %1 selected program %3 not available or will be edited
- 14015 Channel %1 block %2 program %3 is not enabled
- 14016 Channel %1 block %2 error when calling the subroutine via M/T function
- 14017 Channel %1 block %2 syntax error when calling the subroutine via M function
- 14020 Channel %1 block %2 wrong value or wrong number of parameters on function or procedure call
- 14021 Channel %1 block %2 wrong value or wrong number of parameters on function or procedure call
- 14025 Channel %1 block %2 motion synchronous action: illegal modal ID
- 14026 Channel %1 block %2 motion synchronous action: invalid polynomial number in the FCTDEF command
- 14030 Channel %1 block %2 combine OSCILL and POSP during oscillation with in feed motion
- 14033 Channel %1 block %2 involute: no end point programmed
- 14034 Channel %1 block %2 involute: angle of rotation too large
- 14035 Channel %1 block %2 involute: start point invalid
- 14036 Channel %1 block %2 involute: end point invalid
- 14037 Channel %1 block %2 involute: radius invalid
- 14038 Channel %1 block %2 involute not definable: end point error
- 14039 Channel %1 block %2 involute: end point programmed several times
- 14040 Channel %1 block %2 error in end point of circle
- 14045 Channel %1 block %2 error in tangential circle programming
- 14048 Channel %1 block %2 wrong number of revolutions in circle programming
- 14050 Channel %1 block %2 nesting depth for arithmetic operations exceeded
- 14051 Channel %1 block %2 arithmetic error in part program
- 14060 Channel %1 block %2 invalid skip level with differential block skip
- 14070 Channel %1 block %2 memory for variables not sufficient for subroutine call
- 14080 Channel %1 block %2 jump destination %3 not found
- 14082 Channel %1 block %2 label %3 program section not found
- 14085 Channel %1 block %2 instruction not allowed
- 14088 Channel %1 block %2 axis %3 doubtful position
- 14090 Channel %1 block %2 illegal D number
- 14091 Channel %1 block %2 illegal function, index %3 %3
- 14092 Channel %1 block %2 axis %3 is wrong axis type
- 14093 Channel %1 block %2 path interval <= 0 with polynominal interpolation
- 14094 Channel %1 block %2 polynominal degree greater than 3 programmed for polynominal interpolation
- 14095 Channel %1 block %2 radius for circle programming too small
- 14096 Channel %1 block %2 illegal type conversion
- 14097 Channel %1 block %2 string cannot be converted to AXIS type
- 14098 Channel %1 block %2 conversion error: no valid number found
- 14099 Channel %1 block %2 result in string concatenation too long
- 14100 Channel %1 block %2 orientation transformation not available
- 14101 Channel %1 block %2 orientation transformation not active
- 14102 Channel %1 block %2 polynominal degree greater than 5 programmed for orientation vector angle
- 14110 Channel %1 block %2 Euler angles and orientation vector components programmed
- 14111 Channel %1 block %2 Euler angles, orientation vector and transformation axes programmed
- 14112 Channel %1 block %2 programmed orientation path not possible
- 14113 Channel %1 block %2 programmed lead angle too large
- 14114 Channel %1 block %2 programmed tilt angle too large
- 14115 Channel %1 block %2 illegal definition of workpiece surface
- 14116 Channel %1 block %2 absolute orientation programmed while ORIPATH is active
- 14117 Channel %1 block %2 no angle or direction of the cone programmed
- 14118 Channel %1 block %2 no end orientation programmed
- 14119 Channel %1 block %2 no intermediate orientation programmed
- 14120 Channel %1 block %2 plane determination for programmed orientation not possible
- 14122 Channel %1 block %2 angle and direction of the cone programmed
- 14123 Channel %1 block %2 nutation angle of the cone too small
- 14124 Channel %1 block %2 start tangent for orientation is zero
- 14125 Channel %1 block %2 programmed rotation is not possible
- 14129 Channel %1 block %2 orientation angles and orientation vector components programmed
- 14130 Channel %1 block %2 too many initialization values given
- 14131 Channel %1 block %2 orientation axes and lead/tilt angles programmed
- 14132 Channel %1 block %2 orientation axes incorrectly configured
- 14133 Channel %1 block %2 G code for orientation definition not allowed
- 14134 Channel %1 block %2 G code for orientation interpolation not allowed
- 14140 Channel %1 block %2 position programming without transformation not allowed
- 14144 Channel %1 block %2 PTP movement not allowed
- 14146 Channel %1 block %2 CP or PTP movement without transformation not allowed
- 14148 Channel %1 illegal reference system for Cartesian manual traverse
- 14150 Channel %1 block %2 illegal tool carrier number programmed or declared (MD)
- 14151 Channel %1 block %2 illegal tool carrier rotation
- 14152 Channel %1 block %2 tool carrier: invalid orientation. Error code: %3
- 14153 Channel %1 block %2 unknown tool carrier type: %3
- 14154 Channel %1 block %2 The amount of fine correction in parameter %3 of the orientable tool holder %4 is too large
- 14155 Channel %1 block %2 invalid base frame definition for tool carrier offset
- 14156 Channel %1 toolholder selection error at reset
- 14157 Channel %1 block %2 illegal interpolation type with MOVT
- 14159 Channel %1 block %2 more than two angles programmed with ROTS or AROTS
- 14160 Channel %1 block %2 tool length selection without geometry axis specification
- 14165 Channel %1 block %2 active T number does not match selected tool
- 14170 Channel %1 block %2 illegal interpolation type with tool length compensation
- 14180 Channel %1 block %2 H number is not defined
- 14185 Channel %1 block %2 D number is not defined
- 14190 Channel %1 block %2 H number with G49
- 14195 Channel %1 block %2 D number with G49
- 14197 Channel %1 block %2 D number and H number programmed simultaneously
- 14198 Channel %1 block %2 illegal change of tool direction with tool offset
- 14199 Channel %1 block %2 illegal plane change for tool with diameter component
- 14200 Channel %1 block %2 negative polar radius
- 14210 Channel %1 block %2 polar angle too large
- 14250 Channel %1 block %2 negative pole radius
- 14260 Channel %1 block %2 pole angle too large
- 14270 Channel %1 block %2 pole programmed incorrectly
- 14280 Channel %1 block %2 polar coordinates programmed incorrectly
- 14290 Channel %1 block %2 poly nominal degree greater than 5 programmed for poly nominal interpolation
- 14300 Channel %1 block %2 overlaid handwheel motion activated incorrectly
- 14310 Handwheel %1 configuration incorrect or inactive
- 14400 Channel %1 block %2 tool radius compensation active at transformation switchover
- 14401 Channel %1 block %2 transformation not available
- 14402 Channel %1 block %2 spline active at transformation change
- 14403 Channel %1 block %2 preprocessing and main run might not be synchronized
- 14404 Channel %1 block %2 illegal parametrization of transformation
- 14410 Channel %1 block %2 spline active at geometry axis changeover
- 14411 Channel %1 block %2 tool radius compensation active at geometry axis changeover
- 14412 Channel %1 block %2 transformation active at geometry axis changeover
- 14413 Channel %1 block %2 fine tool correction: changeover geometry/channel axis not allowed
- 14414 Channel %1 block %2 GEOAX function: incorrect call
- 14415 Channel %1 block %2 tangent control: changeover geometry/channel axis not allowed
- 14420 Channel %1 block %2 index axis %3 frame not allowed
- 14500 Channel %1 block %2 illegal DEF or PROC instruction in the part program
- 14510 Channel %1 block %2 PROC instruction missing on subroutine call
- 14520 Channel %1 block %2 illegal PROC instruction in data definition section
- 14530 Channel %1 block %2 EXTERN and PROC instruction do not correspond
- 14600 Channel %1 block %2 reload buffer %3 cannot be established
- 14601 Channel %1 block %2 reload buffer could not be deleted
- 14602 Channel %1 block %2 timeout during EXTCALL
- 14610 Channel %1 block %2 compensation block not possible
- 14650 Channel %1 block %2 SETINT instruction with invalid ASUP input
- 14660 Channel %1 block %2 SETINT instruction with invalid priority
- 14700 Channel %1 block %2 timeout during command to interpreter
- 14701 Channel %1 block %2 number of available NC blocks reduced by %3
- 14710 Channel %1 block %2 error in initialization sequence in function %3
- 14720 Channel %1 block %2 axes for centerless transformation not available
- 14730 Channel %1 block %2 conflict at activation of centerless transformation
- 14740 Channel %1 block %2 no tool data available for centerless grinding
- 14745 Channel %1 block %2 centerless grinding not active
- 14750 Channel %1 block %2 too many auxiliary functions programmed
- 14751 Channel %1 block %2 resources for motion synchronous actions not sufficient (code: %3)
- 14752 Channel %1 block %2 DELDTG | STOPREOF conflict
- 14753 Channel %1 block %2 motion synchronous actions with illegal interpolation type
- 14754 Channel %1 block %2 motion synchronous actions and wrong feed type
- 14755 Channel %1 block %2 motion synchronous actions without traverse motion
- 14756 Channel %1 block %2 motion synchronous action and wrong value
- 14757 Channel %1 block %2 motion synchronous action and wrong type
- 14758 Channel %1 block %2 programmed value not available
- 14759 Channel %1 block %2 motion synchronous action and wrong axis type
- 14760 Channel %1 block %2 auxiliary function of a group programmed repeatedly
- 14761 Channel %1 block %2 motion synchronous action: DELDTG function not allowed with active tool radius compensation
- 14762 Channel %1 block %2 too many PLC variables programmed
- 14763 Channel %1 block %2 too many link variables programmed
- 14764 NCU link cannot transfer all link variables immediately
- 14765 NCU link cannot transfer all link variables
- 14766 NCU link is heavily loaded, impending memory shortage
- 14767 Machine data matching via NCU link not complete
- 14770 Channel %1 block %2 auxiliary function programmed incorrectly
- 14780 Channel %1 block %2 unreleased option used
- 14790 Channel %1 block %2 axis %3 programmed by PLC
- 14800 Channel %1 block %2 programmed path speed less or equal to zero
- 14810 Channel %1 block %2 negative axis speed programmed for positioning axis %3
- 14811 Channel %1 block %2 incorrect value range for acceleration of axis/spindle %3
- 14812 Channel %1 block %2 SOFTA not available for axis %3
- 14815 Channel %1 block %2 negative thread lead change programmed
- 14820 Channel %1 block %2 negative value for maximum spindle speed programmed with constant cutting speed
- 14821 Channel %1 block %2 error in selection or deselection of GWPS
- 14822 Channel %1 block %2 incorrect programming of GWPS
- 14823 Channel %1 block %2 error on selection or deselection of tool monitoring
- 14824 Channel %1 block %2 conflict with GWPS
- 14840 Channel %1 block %2 incorrect value range for constant cutting speed
- 14900 Channel %1 block %2 center point and end point programmed simultaneously
- 14910 Channel %1 block %2 invalid angle of aperture for programmed circle
- 14920 Channel %1 block %2 intermediate point of circle incorrect
- 15000 Channel %1 block %2 channel-sync instruction using illegal mark
- 15010 Channel %1 block %2 program coordination instruction with invalid channel number
- 15020 Channel %1 block %2 CHANDATA instruction cannot be executed. Channel %3 is not active
- 15021 Channel %1 block %2 CHANDATA instruction with invalid channel number
- 15025 CHANDATA(%2): channel is not active. Channel data will be ignored.
- 15030 Channel %1 block %2 different measurement system settings
- 15100 Channel %1 block %2 REORG abort caused by log file overflow
- 15110 Channel %1 block %2 REORG not possible
- 15150 Channel %1 block %2 reload from external aborted
- 15160 Channel %1 block %2 wrong preprocessing configuration
- 15165 Channel %1 block %2 error when translating or interpreting PLC Asup %3
- 15166 Channel %1 user system asup _N_ASUP_SPF not available
- 15170 Channel %1 block %2 program %3 could not be compiled
- 15171 Channel %1 block %2 compiled program %3 older than the relevant subroutine
- 15175 Channel %1 block %2 program %3. Interfaces could not be built
- 15180 Channel %1 block %2 program %3 cannot be executed as INI file
- 15185 Channel %1 %2 errors in INI file
- 15190 Channel %1 block %2 not enough free memory for subroutine call
- 15300 Channel %1 block %2 invalid number-of-passed-blocks during block search
- 15310 Channel %1 block %2 file requested during block search is not available
- 15320 Channel %1 block %2 invalid block search command
- 15330 Channel %1 block %2 invalid block number as search target
- 15340 Channel %1 block %2 invalid label as search target
- 15350 Channel %1 block %2 search target not found
- 15360 Channel %1 illegal target of block search (syntax error)
- 15370 Channel %1 target of block search not found
- 15380 Channel %1 block %2 illegal incremental programming in axis %3
- 15390 Channel %1 block %2 %3 not executed during block search
- 15395 Channel %1 master-slave not executable during block search
- 15400 Channel %1 block %2 selected initial init file does not exist
- 15410 Channel %1 block %2 initialization file contains invalid M function
- 15420 Channel %1 block %2 instruction in current mode not allowed
- 15450 Channel %1 block %2 compiled program cannot be stored
- 15460 Channel %1 block %2 syntax error with modal function
- 15500 Channel %1 block %2 illegal angle of shear
- 15700 Channel %1 block %2 illegal cycle alarm number %3
- 15800 Channel %1 block %2 wrong starting conditions for CONTPRON/CONTDCON
- 15810 Channel %1 block %2 wrong array dimension for CONTPRON/CONTDCON
- 15900 Channel %1 block %2 touch probe not allowed
- 15910 Channel %1 block %2 touch probe not allowed
- 15950 Channel %1 block %2 no traverse motion programmed
- 15960 Channel %1 block %2 no traverse motion programmed
Pages: 1 2 3